JVC KD-S7350, KD-S690 User Manual

CD RECEIVER KD-S7350/KD-S690

ENGLISH

RECEPTOR CON CD KD-S7350/KD-S690

RECEPTEUR CD KD-S7350/KD-S690

KD-S7350

S

KD-S690

S

COMPACT

DIGITAL AUDIO

For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.

ESPAÑOL

FRANÇAIS

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

For customer Use:

Enter below the Model No. and
Serial No. which are located on
the top or bottom of the
cabinet. Retain this information
for future reference.

Model No.

Serial No.

GET0131-001A

[J]

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with

ENGLISH

the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT FOR LASER PRODUCTS

Precautions:

1. CLASS 1 LASER PRODUCT

2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure
to beam.

3. CAUTION: Do not open the top cover. There are no user-serviceable parts inside. Leave all
servicing to qualified service personnel.

4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches
to prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.

5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.

How to reset your unit

While holding SEL (select), press (standby/on/attenuator) for more than 2 seconds.
This will reset the built-in microcomputer.

(standby/on/attenuator)

SEL (select)

Notes:

• Your preset adjustments—such as preset channels or sound adjustments—will also be erased.

• If a CD is in the unit, it will eject when you reset the unit. Be careful not to drop the CD.

2

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

CONTENTS

How to reset your unit ............................... 2

How to use the M (MODE) button ............. 3

LOCATION OF THE BUTTONS ............ 4

Control panel ............................................. 4

Remote controller ...................................... 5

Preparing the remote controller ................ 6

BASIC OPERATIONS ....................... 7

Turning on the power ................................ 7

Setting the clock ........................................ 8

RADIO OPERATIONS ...................... 9

Listening to the radio ................................. 9

Storing stations in memory ....................... 10

Tuning in to a preset station ...................... 11

SOUND ADJUSTMENTS ................... 15

Selecting preset sound modes

(C-EQ: custom equalizer) ....................... 15

Adjusting the sound .................................. 16

OTHER MAIN FUNCTIONS ................ 17

Selecting the level display ......................... 17

Detaching the control panel ...................... 18

TROUBLESHOOTING ...................... 19

MAINTENANCE ............................. 20

Handling discs ........................................... 20

SPECIFICATIONS........................... 21

CD OPERATIONS ........................... 12

Playing a CD ............................................. 12

Locating a track or a particular portion

on a CD .................................................. 13

Selecting CD playback modes .................. 14

Prohibiting CD ejection ............................. 14

How to use the M (MODE) button

If you press M (MODE), the unit goes into functions mode and the number buttons and 5/∞
buttons work as different function buttons.

ENGLISH

Ex.: When number button 2 works as MO (monaural) button.

Time countdown indicator

To use these buttons for original functions again after pressing M (MODE), wait for 5 seconds
without pressing any of these buttons until the functions mode is cleared.

• Pressing M (MODE) again also clears the functions mode.

BEFORE USE

*

For safety....

• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.

• Stop the car before performing any complicated
operations.

*

Temperature inside the car....

If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.

3

Control panel

Display window

ENGLISH

a

LOCATION OF THE BUTTONS

s

d

f lk

ghj

1 2

1 (standby/on/attenuator) button
2 SEL (select) button
3 Control dial
4 Loading slot
5 Display window
6 FM/AM button
7 5 (up) button

+10 button

8 4 /¢ buttons
9 0 (eject) button
p DISP (display) button

• Also functions as SSM buttons when pressed
together with M (MODE) button.

q M (MODE) button

• Also functions as SSM buttons when pressed
together with DISP (display) button.

w Remote sensor
e MO (monaural) button
r Number buttons
t RPT (repeat) button
y RND (random) button
u E (EQ: equalizer) button

4 6 9

3

qp e yt

w

5

/

r u i ;

i CD button
o ∞ (down) button

–10 button

; (control panel release) button

Display window

a EQ (equalizer) indicator
s LOUD (loudness) indicator
d CD–in indicator
f CD indicator
g FM band indicators (FM1, FM2, FM3)
h AM band indicator
j Tuner reception indicators

MO (monaural), ST (stereo)

k RND (disc random) indicator
l Volume (or audio) level indicator
/ Main display
z RPT (repeat) indicator

z

87

o

4

Remote controller

S

1 • Turns on the unit if pressed when the unit

is turned off.

• Turns off the unit if pressed and held until
“SEE YOU” appears on the display.

• Drops the volume level in a moment if
pressed briefly.
Press again to resume the volume.

3 Selects the preset stations while listening to

the radio.
Each time you press the button, the preset
station number increases, and the selected
station is tuned in.

4 Selects the sound mode (C-EQ: custom

equalizer).
Each time you press the button, the sound
mode (C-EQ) changes.

5 Selects the band while listening to the radio.

Each time you press the button, the band
changes.

6 Selects the source.

Each time you press the button, the source
changes.

7 Functions the same as the control dial on the

main unit.

Note:

These buttons do not used for adjusting
“CLOCK H,” “CLOCK M,” and “LEVEL”
(see pages 8 and 17).

ENGLISH

2 • Searches for stations while listening to the

radio.

• Fast-forwards or reverses the track if
pressed and held while listening to a CD.

• Skips to the beginning of the next track or
goes back to the beginning of the current
(or previous) tracks if pressed briefly while
listening to a CD.

5

Preparing the remote
controller

3. Return the battery holder.

Insert again the battery holder by pushing it
until you hear a clicking sound.

Before using the remote controller:

ENGLISH

• Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.

Remote sensor

• Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).

Installing the battery

When the controllable range or effectiveness
of the remote controller decreases, replace
the battery.

1. Remove the battery holder.

1) Push out the battery holder in the
direction indicated by the arrow using a
ball point pen or a similar tool.

2) Remove the battery holder.

(back side)

WARNING:

• Store the battery in a place which children
cannot reach.
If a child accidentally swallows the battery,
immediately consult a doctor.

• Do not recharge, short, disassemble or heat the
battery or dispose of in a fire.
Doing any of these things may cause the battery
to give off heat, crack or start a fire.

• Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off
heat, crack or start a fire.

• When throwing away or saving the battery,
wrap in tape and insulate; otherwise, it may
cause the battery to give off heat, crack or start
a fire.

• Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off
heat, crack or start a fire.

(back side)

2. Place the battery.

Slide the battery into the holder with the
+ side facing upwards so that the battery
is fixed in the holder.

6

CAUTION:

DO NOT leave the remote controller in a place
(such as dashboards) exposed to direct sunlight
for a long time. Otherwise, it may be damaged.

Lithium coin
battery (product
number: CR2025)

BASIC OPERATIONS

ENGLISH

1

3

Turning on the power

1

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.

2

Select the source.

To operate the tuner (FM or AM),

see pages 9 – 11.

To play a CD,

see pages 12 – 14.

3

Adjust the volume.

To increase the
volume

To decrease the
volume

Volume (or audio) level indicator
(see page 17)

2

4

Adjust the sound as you want.
(See pages 15 and 16.)

To drop the volume in a moment

Press briefly while listening to any
source. “AT T” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.

• If you turn the control dial, you can also restore
the sound.

To turn off the power

Press and hold for more than one
second.

“SEE YOU” appears, then the unit turns off.

• If you turn off the power while listening to a

CD, CD play will start from where playback has
been stopped previously, next time you turn on
the power.

CAUTION on Volume Setting:

CDs produce very little noise compared with other
sources. If the volume level is adjusted for the
tuner, for example, the speakers may be damaged
by the sudden increase in the output level.
Therefore, lower the volume before playing a CD
and adjust it as required during playback.

Volume level appears.

7

ENGLISH

Setting the clock

1

Press and hold SEL (select) for more
than 2 seconds.

“CLOCK H,” “CLOCK M,” or “LEVEL”
appears on the display.

2

Set the hour.

1 Select “CLOCK H” (hour) if not shown on

the display.

LEVEL

2 Adjust the hour.

2 Adjust the minute.

4

Finish the setting.

CLOCK MCLOCK H

To check the current clock time or change the
display mode

Press DISP (display) repeatedly.
Each time you press the button,
the display mode changes as
follows:

• During tuner operation:

ClockFrequency

• During CD operation:

3

Set the minute.

1 Select “CLOCK M” (minute).

8

LEVEL

ClockElapsed playing time

• During power off:

The power turns on and the clock time is

CLOCK MCLOCK H

shown for 5 seconds, then the power turns
off.

RADIO OPERATIONS

ENGLISH

Listening to the radio

You can use either automatic searching or manual
searching to tune in to a particular station.

Searching a station automatically:
Auto search

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

Selected band appears.

Lights up when receiving an FM stereo
broadcast with sufficient signal strength.

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.

2

Start searching a station.

To search stations of
higher frequencies

To stop searching before a station is
received, press the same button you have

pressed for searching.

Searching a station manually:
Manual search

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.

2

Press and hold ¢ or 4
until “M” (manual) starts flashing on
the display.

To search stations of
lower frequencies

When a station is received, searching stops.

CONTINUED ON THE NEXT PAGE

9

3

Tune in to a station you want while
“M” (manual) is flashing.

ENGLISH

• If you release your finger from the button,

• If you hold down the button, the frequency

To tune in to stations
of higher frequencies

To tune in to stations
of lower frequencies

the manual mode will automatically turns
off after 5 seconds.

keeps changing (in 200 kHz intervals for
FM and 10 kHz for AM) until you release
the button.

Storing stations in memory

You can use one of the following two methods to
store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong­station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).

1

Select the FM band (FM1 – 3) you
want to store FM stations into.

Each time you press the
button, the band changes as
follows:

When an FM stereo broadcast is hard to
receive

1 Press M (MODE) to enter the

functions mode while listening
to an FM stereo broadcast.

2 Press MO (monaural), while

still in the functions mode, so
that the MO indicator lights up
on the display.
Each time you press the
button, the MO indicator lights
up and goes off alternately.

MO (monaural) indicator

When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved.

FM1 FM2 FM3 AM

2

Press and hold both buttons for
more than 2 seconds.

“- -SSM- -” appears, then disappears when
automatic preset is over.

Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number
buttons—No.1 (lowest frequency) to No.6
(highest frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.

10

Manual preset

You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.

Ex.: Storing FM station of 88.3 MHz into the

preset number 1 of the FM1 band.

1

Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

2

Tune in to a station (in this example,
of 88.3 MHz).

To tune in to stations
of higher frequencies

To tune in to stations
of lower frequencies

4

Repeat the above procedure to store
other stations into other preset
numbers.

Notes:

• A previously preset station is erased when a new
station is stored in the same preset number.

• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.

Tuning in to a preset station

You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on pages 10 and 11.

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

ENGLISH

3

Press and hold the number button
(in this example, 1) for more than
2 seconds.

“P1” flashes for a few seconds.

2

Select the number (1 – 6) for the
preset station you want.

Note:

You can also use the 5 (up) or ∞ (down) button on
the unit to select the next or previous preset stations.
Each time you press the 5 (up) or ∞ (down) button,
the next or previous preset station is tuned in.

11

ENGLISH

CD OPERATIONS

Playing a CD

Insert a CD into the loading slot.

The unit turns on, draws
the CD and starts
playback automatically.

Note on One-Touch Operation:

When a CD is already in the loading slot, pressing
CD turns on the unit and starts playback
automatically.

The CD–in indicator flashes.

The CD–in indicator light up.

Total playing time of
the inserted disc

Total track number
of the inserted disc

Note:

When a CD is inserted upside down, “EJECT” and
the CD–in indicator flash on the display and the CD
automatically ejects.

To stop play and eject the CD

Press 0.
CD play stops and the CD automatically ejects
from the loading slot. The source changes to the
tuner (you will hear the last received station.)

• If you change the source, CD play also stops
(without ejecting the CD).
Next time you select “CD” as the source, CD
play starts from where playback has been
stopped previously.

Notes:

• If the ejected disc is not removed for about
15 seconds, the disc is automatically inserted again
into the loading slot to protect it from dust.
(CD play will not start this time.)

• You can eject the CD even when the unit is turned
off.

About mistracking:

Mistracking may result from driving on extremely
rough roads. This does not damage the unit and
the CD, but will be annoying.
We recommend that you stop CD play while
driving on such rough roads.

Elapsed playing time Current track

All tracks will be played repeatedly until you stop
playback.

12

Locating a track or a
particular portion on a CD

To fast-forward or reverse the track

Press and hold ¢ ,
while playing a CD, to
fast-forward the track.

To go to a track quickly (+10 and –10
buttons)

1 Press M (MODE) to enter the functions mode

while playing a CD.

ENGLISH

2 Press +10 or –10.

Press and hold 4 ,
while playing a CD, to
reverse the track.

To go to the next or previous tracks

Press ¢ briefly,
while playing a CD, to go
ahead to the beginning of
the next track.
Each time you press the
button consecutively, the
beginning of the next
tracks is located and
played back.

Press 4 briefly,
while playing a CD, to go
back to the beginning of
the current track.
Each time you press the
button consecutively, the
beginning of the previous
tracks is located and
played back.

To go to a particular track directly

Press the number button corresponding to the
track number to start its playback.

To skip 10 tracks* forwards
up to the last track

To skip 10 tracks* backwards
up to the first track

* The first time you press +10 or –10 button,

the track skips to the nearest higher or lower
track with a track number of multiple ten (ex.

10th, 20th, 30th).
Then each time you press the button, you can
skip 10 tracks (see “How to use the +10 and
–10 buttons” below).

• After the last track, the first track will be

selected, and vice versa.

How to use the +10 and –10 buttons

• Ex. 1: To select track number 32 while

playing track number 6.

(Three times) (Twice)

Track 6 \ 10 \ 20 \ 30 \ 31 \ 32

• Ex. 2 :To select track number 8 while

playing track number 36.

• To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.

• To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than one
second.

(Three times) (Twice)

Track 36 \ 30 \ 20 \ 10 \ 9 \ 8

13

Selecting CD playback modes

Prohibiting CD ejection

To play back tracks at random
(Disc Random Play)

ENGLISH

You can play back all tracks on the CD at
random.

1 Press M (MODE) to enter the

functions mode while playing a
CD.

2 Press RND (random), while

still in the functions mode, so
that “DISC RND” appears on
the display.
Each time you press the
button, disc random play mode
turns on and off alternately.

RND (disc random) indicator

When disc random play is turned on, the

RND indicator lights up on the display. A

track randomly selected starts playing.

To play back tracks repeatedly
(Track Repeat Play)

You can play back the current track repeatedly.

1 Press M (MODE) to enter the

functions mode while playing a
CD.

You can prohibit CD ejection and can lock a CD
in the loading slot.

While pressing CD, press and hold 0 for
more than 2 seconds.

“EJECT” flashes on the display for about
5 seconds, and the CD is locked and cannot be
ejected.

To cancel the prohibition and unlock the CD,

press 0 again for more than 2 seconds, while
pressing CD.
“EJECT” and the CD–in indicator flash on the
display, and the CD ejects from the loading slot.

The CD–in indicator flashes.

2 Press RPT (repeat), while still

in the functions mode, so that
“TRK RPT” appears on the
display.
Each time you press the
button, track repeat play mode
turns on and off alternately.

When track repeat play is turned on, the RPT
indicator lights up on the display. The current
track starts playing repeatedly.

14

RPT indicator

SOUND ADJUSTMENTS

Selecting preset sound modes
(C-EQ: custom equalizer)

You can select a preset sound mode (C-EQ:
custom equalizer) suitable to the music genre.

Select the sound mode you want.

When you press the button
once, the last selected sound
mode is recalled and applied
to the current source.

Ex.: If you have selected “USER” previously

Then, each time you press the
button, the sound modes
change as follows:

USER

The EQ indicator lights up when any sound
mode other than “USER” is selected.

ROCK

CLASSIC

POPSHIP HOPJAZZ

Indication For: Preset values

BAS TRE LOUD

USER (Flat sound) 00 00 OFF

ROCK Rock or +03 +01 ON

disco music

CLASSIC Classical +01 –02 OFF

music

POPS Light music +04 +01 OFF

HIP HOP Funk or rap +02 00 ON

music

JAZZ Jazz music +02 +03 OFF

Note:

You can adjust each sound mode to your preference.
Once you make an adjustment, it is automatically
stored for the currently selected sound mode. See
“Adjusting the sound” on page 16.

ENGLISH

Ex.: When you select “ROCK”

15

Adjusting the sound

2

Adjust the setting.

You can adjust the sound characteristics to your
preference.

ENGLISH

1

Select the item you want to adjust.

Each time you press the
button, the adjustable items
change as follows:

BAS

(bass)

VOL

(volume)

Indication To do: Range

1

BAS*

TRE*

FAD*

BAL Adjust the left L06 (Left only)

LOUD*1Boost low and high

VOL*

Adjust the bass. –06 (min.)

1

Adjust the treble. –06 (min.)

2

Adjust the front R06 (Rear only)
and rear speaker |
balance. F06 (Front only)

and right speaker |
balance. R06 (Right only)

frequencies to
produce a well­balanced sound
at low volume
level.

3

Adjust the volume. 00 (min.)

TRE

(treble)

LOUD

(loudness)

(balance)

|
+06 (max.)

|
+06 (max.)

LOUD ON
|
LOUD OFF

|
50 (max.)

FAD

(fader)

BAL

To increase the level or
turn on the loudness

To decrease the level or
turn off the loudness

Equalization pattern changes as you
adjust the bass or treble.

Ex. 1: When you adjust “TRE” (treble)

Ex. 2: When you turn on the loudness

3

Repeat steps 1 and 2 to adjust the
other items.

To reset each sound mode to the factory
settings, repeat the same procedure and

reassign the preset values listed in the table on
page 15.

*1When you adjust the bass, treble, or loudness, the

adjustment you have made is stored for the
currently selected sound mode (C-EQ) including
“USER.”

*2If you are using a two-speaker system, set the fader

level to “00.”

*3Normally the control dial works as the volume

control. So you do not have to select “VOL” to
adjust the volume level.

16

OTHER MAIN FUNCTIONS

AUDIO 2AUDIO 1

OFF

Selecting the level display

You can select the level display according to your
preference.
When shipped from the factory, “AUDIO 2” is
selected.

1

Press and hold SEL (select) for more
than 2 seconds.

“CLOCK H,” “CLOCK M,” or “LEVEL”
appears on the display.

2

Select “LEVEL” if not shown on the
display.

CLOCK MCLOCK H

LEVEL

3

Select the desired mode.

Ex.: When you select “AUDIO 2”

• AUDIO 1: Shows the audio level indicator.

• AUDIO 2: Alternates “AUDIO 1” setting
and illumination display.

• OFF: Erases the audio level indicator.

4

Finish the setting.

ENGLISH

17

Detaching the control panel

You can detach the control panel when leaving
the car.
When detaching or attaching the control panel,

ENGLISH

be careful not to damage the connectors on the
back of the control panel and on the panel
holder.

Detaching the control panel

Before detaching the control panel, be sure to
turn off the power.

1

Unlock the control panel.

2

Lift and pull the control panel out of
the unit.

Attaching the control panel

1

Insert the left side of the control
panel into the groove on the panel
holder.

2

Press the right side of the control
panel to fix it to the panel holder.

18

3

Put the detached control panel into
the provided case.

Note on cleaning the connectors:

If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.

Connectors

TROUBLESHOOTING

What appears to be trouble is not always serious. Check the following points before calling a service
center.

Symptoms

• Sound cannot be heard
from the speakers.

• This unit does not work at
all.

General

• SSM (Strong-station
Sequential Memory)
automatic preset does not
work.

FM/AM

• Static noise while listening
to the radio.

• CD automatically ejects.

• CD-R/CD-RW cannot be

played back.

• Tracks on the CD-R/CD-RW
cannot be skipped.

• CD can be neither played
back nor ejected.

CD Playback

• CD sound is sometimes
interrupted.

Causes

The volume level is set to the
minimum level.

Connections are incorrect.

The built-in microcomputer
may have functioned
incorrectly due to noise, etc.

Signals are too weak.

The antenna is not connected
firmly.

CD is inserted upside down.

CD-R/CD-RW is not finalized.

CD is locked.

The CD player may function
incorrectly.

You are driving on rough
roads.

Remedies

Adjust it to the optimum level.

Check the cords and
connections.

While holding SEL (select),
press (standby/on/
attenuator) for more than
2 seconds to reset the unit. (The
clock setting and preset stations
stored in memory are erased.)
(See page 2.)

Store stations manually.

Connect the antenna firmly.

Insert the CD correctly.

• Insert a finalized CD-R/
CD-RW.

• Finalize the CD-R/CD-RW
with the component which
you used for recording.

Unlock the CD. (See page 14.)

While holding

(standby/on/attenuator), press
0 (eject) for more than
2 seconds. Be careful not to
drop the CD when it is ejected.

Stop playback while driving on
rough roads.

ENGLISH

•“NO DISC” appears on the
display.

CD is scratched.

Connections are incorrect.

No CD in the loading slot.

CD is inserted incorrectly.

Change the CD.

Check the cords and
connections.

Insert a CD into the loading slot.

Insert the CD correctly.

19

MAINTENANCE

Handling discs

This unit has been designed to reproduce CDs,
CD-Rs (Recordable), and CD-RWs (Rewritable).

• This unit is not compatible with MP3 discs.

ENGLISH

How to handle discs

When removing a disc
from its case, press down

the center holder of the case
and lift the disc out, holding
it by the edges.

• Always hold the disc by the edges. Do not
touch its recording surface.

When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).

• Make sure to store discs into the cases after
use.

To keep discs clean

A dirty disc may not play correctly.
If a disc does become dirty, wipe it
with a soft cloth in a straight line
from center to edge.

To play new discs

New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
unit may reject the disc.
To remove these rough spots, rub the edges with
a pencil or ball-point pen, etc.

Moisture condensation

Moisture may condense on the lens inside the
CD player in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car.

Should this occur, the CD player may
malfunction. In this case, eject the disc and leave
the unit turned on for a few hours until the
moisture evaporates.

Center holder

When playing a CD-R or CD-RW

Before playing back CD-Rs or CD-RWs, read
their instructions or cautions carefully.

• Use only “finalized” CD-Rs or CD-RWs.

• Some CD-Rs or CD-RWs may not play back on

this unit because of their disc characteristics,
and for the following reasons:

– Discs are dirty or scratched.
– Moisture condensation on the lens inside the

unit.

– The pickup lens inside the unit is dirty.

• CD-RWs may require a longer readout time

since the reflectance of CD-RWs is lower than
that of regular CDs.

• CD-Rs or CD-RWs are susceptible to high
temperatures or high humidity, so do not leave
them inside your car.

• Do not use following CD-Rs or CD-RWs:
– Discs with stickers, labels, or protective seal

stuck to the surface.

– Discs on which labels can be directly printed

by an ink jet printer.
Using these discs under high temperatures or
high humidity may cause malfunctions or
damage to discs. For example,
– Stickers or labels may shrink and warp a

disc.
– Stickers or labels may peel off so discs

cannot be ejected.
– Print on discs may get sticky.
Read instructions or cautions about labels and
printable discs carefully.

CAUTIONS:

• Do not insert 8 cm (3 3/16") discs (single CDs)
into the loading slot. (Such discs cannot be
ejected.)

• Do not insert any disc of unusual shape—like a
heart or flower; otherwise, it will cause a
malfunction.

• Do not expose discs to direct sunlight or any
heat source or place them in a place subject to
high temperature and humidity. Do not leave
them in a car.

• Do not use any solvent (for example,
conventional record cleaner, spray, thinner,
benzine, etc.) to clean discs.

20

Warped
disc

Sticker

Sticker
residue

Disc

Stick-on
label

SPECIFICATIONS

AUDIO AMPLIFIER SECTION

Maximum Power Output:

Front: 45 W per channel
Rear: 45 W per channel

Continuous Power Output (RMS):

Front: 17 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than

0.8% total harmonic distortion.

Rear: 17 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than

0.8% total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:

Bass: ±10 dB at 100 Hz

Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:

2.0 V/20 kΩ load (full scale)

Output Impedance: 1 kΩ

TUNER SECTION

Frequency Range:

FM: 87.5 MHz to 107.9 MHz

AM: 530 kHz to 1 710 kHz

[FM Tuner]

Usable Sensitivity:

11.3 dBf (1.0 µV/75 Ω)

50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75 Ω)

Alternate Channel Selectivity (400 kHz):

65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB

CD PLAYER SECTION

Type: Compact disc player
Signal Detection System: Non-contact optical

pickup (semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit

GENERAL

Power Requirement:

Operating Voltage: DC 14.4 V

(11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature:

0°C to +40°C (32°F to 104°F)

Dimensions (W × H × D):

Installation Size (approx.):

182 mm × 52 mm × 150 mm
(7-3/16" × 2-1/16" × 5-15/16")

Panel Size (approx.):

188 mm × 58 mm × 11 mm
(7-7/16" × 2-5/16" × 7/16")

Mass (approx.):

1.3 kg (2.9 lbs) (excluding accessories)

Design and specifications are subject to change
without notice.

If a kit is necessary for your car, consult your
telephone directory for the nearest car audio
speciality shop.

ENGLISH

[AM Tuner]

Sensitivity: 20 µV
Selectivity: 35 dB

21

http://www.jvcmobile.c

Visit us on-line for

Technical Support & Customer Satisfaction Survey.

US RESIDENTS ONLY

om

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to Reset

Still having trouble??

USA ONLY

Call 1-800-252-5722

http://www.jvc.com

We can help you!

EN, SP, FR 1202KKSMDTJEIN

© 2002 VICTOR COMPANY OF JAPAN, LIMITED

JVC

KD-S890/KD-S7350/KD-S690

Installation/Connection Manual
Manual de instalación/conexión
Manuel d’installation/raccordement

GET0131-002A

[J]

ENGLISH

• This unit is designed to operate on 12 V DC, NEGATIVE ground
electrical systems.

INSTALLATION (IN-DASH MOUNTING)

• The following illustration shows a typical installation. However, you
should make adjustments corresponding to your specific car. If you
have any questions or require information regarding installation kits,
consult your JVC car audio dealer or a company supplying kits.

1

Before mounting: Press (control panel release button) to
detach the control panel if already attached.

* When shipped from the factory, the control panel is packed in the

hard case.

2

Remove the trim plate.

3

Remove the sleeve after disengaging the sleeve locks.
1 Stand the unit.

Note: When you stand the unit, be careful not to damage the
fuse on the rear.

2 Insert the 2 handles between the unit and the sleeve, as

illustrated, to disengage the sleeve locks.

3 Remove the sleeve.

Note: Be sure to keep the handles for future use after installing
the unit.

4

Install the sleeve into the dashboard.
* After the sleeve is correctly installed into the dashboard, bend the

appropriate tabs to hold the sleeve firmly in place, as illustrated.

5

Fix the mounting bolt to the rear of the unit’s body and place the
rubber cushion over the end of the bolt.

6

Do the required electrical connections.

7

Slide the unit into the sleeve until it is locked.

8

Attach the trim plate.

9

Attach the control panel.

ESPAÑOL

• Esta unidad está diseñada para funcionar con 12 V de CC, con
sistemas eléctricos de masa NEGATIVA.

INSTALACION (MONTAJE EN EL
TABLERO DE INSTRUMENTOS)

• La siguiente ilustración muestra una instalación típica. Sin embargo
usted deberá efectuar los ajustes correspondientes a su automóvil. Si
tiene alguna pregunta o necesita información acerca de las
herramientas para instalación, consulte con su concesionario de JVC
de equipos de audio para automóviles o a una compañía que
suministra tales herramientas.

1

Antes de instalar: Pulse (soltar panel de control) para separar
el panel de control si ya está unido.

* Cuando se envía de la fábrica, el panel de control está embalado

en el estuche duro.

2

Retire la placa de guarnición.

3

Retire la cubierta después de desenganchar los retenes de la
cubierta.

1 Ponga la unidad vertical.

Nota: Al poner la unidad vertical, tenga cuidado de no dañar el
fusible provisto en la parte posterior.

2 Inserte las 2 manijas entre la unidad y la cubierta tal como en la

ilustración y desenganche los retenes de la cubierta.

3 Retire la cubierta.

Nota: Después de instalar la unidad, asegúrese de guardar las
manijas para uso futuro.

4

Instale la cubierta en el tablero de instrumentos.
* Después de que la cubierta esté correctamente instalada en el

tablero de instrumentos, doble las lengüetas correspondientes
para sostener la cubierta firmemente en su lugar, tal como se
muestra.

5

Fije el perno de montaje en la parte trasera del cuerpo de la unidad
y coloque el cojín de goma sobre el extremo del perno.

6

Realice las conexiones eléctricas requeridas.

7

Deslice la unidad dentro de la cubierta hasta que quede trabada.

8

Coloque la placa de guarnición.

9

Coloque el panel de control.

1202KKSMDTJEIN

JVC

EN, SP, FR

FRANÇAIS

• Cet appareil est conçu pour fonctionner sur des sources de courant
continu de 12 V à masse NEGATIVE.

INSTALLATION (MONTAGE DANS LE
TABLEAU DE BORD)

• L’illustration suivante est un exemple d’installation typique. Cependant,
vous devez faire les ajustements correspondant à votre voiture
particulière. Si vous avez des questions ou avez besoin d’information
sur des kits d’installation, consulter votre revendeur d’autoradios JVC
ou une compagnie d’approvisionnement.

1

Avant le montage:

commande) pour éventeullement détacher le panneau de
commande.

* Lorsque ce panneau de commande sort d’usine, il est rangé dans

un étui de transport.

2

Retirer la plaque d’assemblage.

3

Libérer les verrous du manchon et retirer le manchon.

1

Poser l’appareil à la verticale.

Remarque:

attention de ne pas endommager le fusible situé sur l’arrière.

2

Insérer les 2 poignées entre l’appareil et le manchon comme
indiqué pour désengagé les verrous de manchon.

3

Retirer le manchon.

Remarque:

utilisation ultérieur, après l’installation de l’appareil.

4

Installer le manchon dans le tableau de bord.
* Après installation correcte du manchon dans le tableau de bord,

plier les bonnes pattes pour maintenir fermement le manchon en
place, comme montré.

5

Monter le boulon de montage sur l’arrière du corps de l’appareil
puis passer l’amortisseur en caoutchouc sur l’extrémité du boulon.

6

Réalisez les connexions électriques.

7

Faire glisser l’appareil dans le manchon jusqu’à ce qu’il soit
verrouillé.

8

Attachez la plaque d’assemblage.

9

Remonter le panneau de commande.

Appuyer sur (déblocage du panneau de

Lorsque vous mettez l’appareil à la verticale, faire

S’assurer de garder les poignées pour une

Control panel

12

Panel de control

Panneau de commande

Handle

Manija

Poignée

3

Lock Plate

Placa de bloqueo

Plaque de verrouillage

Slot

Ranura

Fente

Trim plate

Placa de guarnición

Plaque d’assemblage

Rubber cushion

Cojín de goma

Amortisseur en caoutchouc

Sleeve

Cubierta

Manchon

7

4

Dashboard

Tablero de instrumentos

Tableau de bord

184 mm

53 mm

5

Mounting bolt

Perno de montaje

Boulon de montage

Fuse

Fusible

Fusible

Sleeve

Cubierta

Manchon

9

Control panel

Panel de control

Panneau de commande

8

6

4

*

Trim plate

Placa de guarnición

Plaque d’assemblage

1

See “ELECTRICAL CONNECTIONS.”

Véase “CONEXIONES ELECTRICAS”.

Référez-vous “RACCORDEMENTS
ELECTRIQUES” .

• When using the optional stay

• Cuando emplea un soporte opcional

• Lors de l’utilisation du hauban en option

Washer

Arandela

Rondelle

Dashboard

Tablero de instrumentos

Tableau de bord

Fire wall

Tabique a prueba
de incendios

Cloison

Sleeve

Cubierta

Manchon

Mounting bolt

Perno de montaje

Boulon de montage

Stay (option)

Soporte (opción)

Hauban (en option)

Lock nut

Tuerca de
seguridad

Ecrou d’arrêt

Screw (option)

Tornillo (opción)

Vis (en option)

• When installing the unit without using the sleeve

• Instalación de la unidad sin utilizar la manga

• Lors de l’installation de l’appareil scans utiliser de manchon

In a Toyota for example, first remove the car radio and install the unit in its place.

En un Toyota por ejemplo, primero retire la radio del automóvil y luego instale la unidad en su lugar.

Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.

Flat type screws (M5 x 6 mm)*

Tornillos tipo plano (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Bracket*

Ménsula*

Support*

Pocket

Compartimiento

Poche

Bracket*

Ménsula*

Support*

* Not included with this unit.

* No suministrado con esta unidad.

*

Non fourni avec cet appareil.

Flat type screws (M5 x 6 mm)*

Tornillos tipo plano (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Removing the unit

• Before removing the unit, release the rear section.

1

Remove the control panel.

2

Remove the trim plate.

3

Insert the 2 handles into the slots, as shown. Then, while gently
pulling the handles away from each other, slide out the unit. (Be

sure to keep the handles after installing it.)

Control panel

Panel de control

Panneau de commande

Note : When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If longer screws are

Nota : Cuando instala la unidad en la ménsula de montaje, asegúrese de utilizar los tornillos de 6 mm de longitud. Si

Remarque :

used, they could damage the unit.

se utilizan tornillos más largos, éstos pueden dañar la unidad.

Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une longueur de 6 mm.
Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Extracción de la unidad

• Antes de extraer la unidad, libere la sección trasera.

1

Retire el panel de control.

2

Retire la placa de guarnición.

3

Inserte las 2 manijas entre las ranuras, como se muestra. Luego,
separe gentilmente las manijas y extraiga la unidad. (Asegúrese de

conservar las manijas después de instalarlo.)

Trim plate

Placa de guarnición

Plaque d’assemblage

Retrait de l’appareil

•

Avant de retirer l’appareil, libérer la section arrière.

1

Retirer le panneau de commande.

2

Retirer la plaque d’assemblage.

3

Introduire les 2 poignées dans les fentes, comme montré. Puis, tout
en tirant doucement les poignées écartées, faire glisser l’appareil
pour le sortir.

l’installation de l’appareil.)

(S’assurer de conserver les poignées après

321

Handle

Manija

Poignée

Parts list for installation and connection

The following parts are provided with this unit.
After checking them, please set them correctly.

Hard case/Control panel

Estuche duro/Panel de control

Etui de transport/Panneau de
commande

Trim plate

Placa de guarnición

Plaque d’assemblage

Handles

Manijas

Poignées

Lista de piezas para instalación y conexión

Con esta unidad se suministran las siguientes piezas.
Después de inspeccionarlas, colóquelas correctamente.

Sleeve

Cubierta

Manchon

Power cord

Cordón de alimentación

Cordon d’alimentation

Lock nut (M5)

Tuerca de seguridad (M5)

Ecrou d’arrêt (M5)

Liste des pièces pour l’installation et
raccordement

Les pièces suivantes sont fournies avec cet appareil.
Après vérification, veuillez les placer correctement.

RM-RK50

For KD-S890
Para KD-S890
Pour le KD-S890

RM-RK60

Remote controller

Mando a distancia

Télécommade

Battery

Pila

Pile

CR2025

Mounting bolt (M5 x 20 mm)

Perno de montaje (M5 x 20 mm)

Boulon de montage (M5 x 20 mm)

Rubber cushion

Cojín de goma

Amortisseur en caoutchouc

Washer (ø5)

Arandela (ø5)

Rondelle (ø5)

For KD-S7350/KD-S690
Para KD-S7350/KD-S690
Pour le KD-S7350/KD-S690

Remote controller

Mando a distancia

Télécommade

Battery

Pila

Pile

2

CR2025

ESPAÑOL

FRANÇAISENGLISH

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the battery’s
negative terminal and make all electrical connections before installing the
unit. If you are not sure how to install this unit correctly, have it installed by
a qualified technician.

Note:
This unit is designed to operate on 12 V DC, NEGATIVE ground
electrical systems. If your vehicle does not have this system, a voltage

inverter is required, which can be purchased at JVC car audio dealers.

• Replace the fuse with one of the specified rating. If the fuse blows
frequently, consult your JVC car audio dealer.

• If noise is a problem...
This unit incorporates a noise filter in the power circuit. However, with
some vehicles, clicking or other unwanted noise may occur. If this
happens, connect the unit’s rear ground terminal (see connection
diagram) to the car’s chassis using shorter and thicker cords, such as
copper braiding or gauge wire. If noise still persists, consult your JVC car
audio dealer.

• Maximum input of the speakers should be more than 50 W (for
KD-S890) and 45 W (for KD-S7350/KD-S690) both at the rear and at the
front, with an impedance of 4 Ω to 8 Ω.

• Be sure to ground this unit to the car’s chassis.

• The heat sink becomes very hot after use. Be careful not to touch it

when removing this unit.

Heat sink

Sumidero térmico

Dissipateur de chaleur

CONEXIONES ELECTRICAS

Para evitar cortocircuitos, recomendamos que desconecte el terminal
negativo de la batería y que efectúe todas las conexiones eléctricas
antes de instalar la unidad. Si usted no está seguro de cómo instalar
correctamente la unidad, hágala instalar por un técnico cualificado.

Nota:
Esta unidad está diseñada para funcionar con 12 V de CC, con
sistemas eléctricos de masa NEGATIVA. Si su vehículo no posee este

sistema, será necesario un inversor de tensión, que puede ser
adquirido en los concesionarios de JVC de equipos de audio para
automóviles.

• Reemplace el fusible por uno con la corriente especificada. Si el
fusible se quemase frecuentemente consulte con su concesionario de
JVC de equipos de audio para automóviles.

• Si el ruido fuese un problema...
Esta unidad tiene un filtro de ruido en el circuito de alimentación. Sin
embargo, en algunos vehículos, pueden producirse chasquidos u
otros ruidos indeseados. En tal caso conecte el terminal de tierra
posterior (véase diagrama de conexión) del receptor al chasis del
automóvil, utilizando cordones más gruesos y cortos tales como
alambre de cobre trenzado o de grueso calibre. Si el ruido persiste,
consulte a su concesionario de JVC de equipos de audio para
automóvil.

• La entrada máxima de los altavoces debe ser de más de 50 W (para
KD-S890) y de 45 W (para KD-S7350/KD-S690) tanto en la parte
trasera como en la delantera, con una impedancia de 4 Ω a 8 Ω.

• Asegúrese de conectar esta unidad a tierra en el chasis del

automóvil.

• El sumidero térmico estará muy caliente después del uso. Asegúrese
de no tocarlo al desmontar esta unidad.

RACCORDEMENTS ELECTRIQUES

Pour éviter tout court-circuit, nous vous recommandons de débrancher la
borne négative de la batterie et d’effectuer tous les raccordements
électriques avant d’installer l’appareil. Si l’on n’est pas sûr de pouvoir
installer correctement cet appareil, le faire installer par un technicien
qualifié.

Remarque:

Cet appareil est conçu pour fonctionner sur des sources de courant
continu de
d’alimentation, il vous faut un convertisseur de tension, que vous pouvez
acheter chez un revendeur d’autoradios JVC.

•

Remplacer le fusible par un de la valeur précisée. Si le fusible saute
souvent, consulter votre revendeur d’autoradios JVC.

•

Si le bruit est un problème...
Cet appareil incorpore un filtre de bruit dans le circuit d’alimentation.
Cependant, avec certains véhicules, quelques claquements ou autres
bruits non désirés risquent de se produire. Si cela arrive, raccorder la

borne arrière de masse

diagramme de raccordement) en utiliscant des cordons les plus gros et
les plus courts possibles telle qu’une barre de cuivre ou une tresse. Si le
bruit persiste, consulter votre revendeur d’autoradios JVC.

•

L’entrée maximum des enceintes doit être supérieure à 50 W (pour le
KD-S890) et 45 W (pour le KD-S7350/KD-S690), pour l’arrière et pour
l’avant, et l’impédance doit être comprise entre

• S’assurer de raccorder la mise à la masse de cet appareil au
châssis de la voiture.

•

Le dissipateur de chaleur devient très chaud après usage. Faire attention
de ne pas le toucher en retirant cet appareil.

12 V à masse NEGATIVE

de l’appareil au châssis de la voiture (voir le

. Si votre véhicule n’offre pas ce type

4 Ω à 8 Ω

.

Typical connections / Conexiones tipicas / Raccordements typiques

Before connecting: Check the wiring in the vehicle carefully. Incorrect
connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car
body may be different in color.

1

Connect the colored leads of the power cord to the car battery,
speakers and automatic antenna (if any) in the following sequence.

1 Black: ground
2 Yellow: to car battery (constant 12 V)
3 Red: to an accessory terminal
4 Blue with white stripe: to remote lead of other equipment or

automatic antenna if any (200 mA max.)

5 Others: to speakers

2

Connect the antenna cord.

3

Finally connect the wiring harness to the unit.

Rear ground terminal

Terminal de tierra posterior

Borne arrière de masse

Only for KD-S890/KD-S7350
Solo para KD-S890/KD-S7350

Seluement pour le

KD-S890/

KD-S7350

Antes de la conexión: Verifique atentamente el conexionado del
vehículo. Una conexión incorrecta podría producir daños graves en la
unidad.
Los cordones del cable de alimentación y los del conector procedentes
de la carrocería del automóvil podrían ser de diferentes en color.

1

Conecte los conductores de color del cable de alimentación a la
batería del automóvil, altavoces y antena motriz (si la hubiere) en la
secuencia siguiente.

1 Negro: a tierra
2 Amarillo: a la batería del automóvil (12 V constantes)
3 Rojo: a un terminal de accesorio
4 Azul con rayas blancas: al conductor remoto de otro equipo o de

la antena automática, si hubiere (máx. 200 mA)

5 Otros: a los altavoces

2

Conecte el cable de antena.

3

Por último, conecte el cable de alimentación a la unidad.

Avant de commencer la connexion:

du véhicule. Une connexion incorrecte peut endommager sérieusement
l’appareil.
Le fil du cordon d’alimentation et ceux des connecteurs du châssis de la
voiture peuvent être différents en couleur.

1

Connectez les fils de couleur du cordon d’alimentation à la batterie
de la voiture, aux enceintes et à l’antenne automatique (s’il y en a
une) dans l’ordre suivant.

1

Noir: à la masse

2

Jaune: à la batterie de la voiture (12 V constant)

3

Rouge: à une borne accessoire

4

Bleu avec bande blanche: au fil de télécommande de l’autre
appareil ou à l’antenne automatique s’il y en a une (200 mA max.)

5

Autres: aux enceintes

2

Connectez le cordon d’antenne.

3

Finalement, connectez le faisceau de fils à l’appareil.

Vérifiez attentivement le câblage

1

Line out (see
diagram )

Salida de línea
(véase diagrama )

Sortie de ligne (voir
le diagramme )

Antenna terminal

Terminal de la antena

Borne de l’antenne

2

To antenna

A la antena

A l’antenne

*1 : Before checking the operation of this unit prior to

installation, this lead must be connected, otherwise
power cannot be turned on.

*1 : Antes de comprobar el funcionamiento de esta unidad

previa a de la instalación, es necesario conectar este
cable, de lo contrario no se podrá conectar la
alimentación.

*1 : Pour vérifier le fonctionnement de cet appareil avant

installation, ce fil doit être raccordé, sinon l’appareil ne
peut pas être mis sous tension.

3

15 A fuse

15

Fusible de 15 A

Fusible 15 A

Black

Negro

Noir

1

1

Yellow*

Amarillo*

Jaune*

1

1

2

Red

Rojo

Rouge

3

Blue with white stripe

Azul con rayas blancas

Bleu avec bande blanche

To metallic body or chassis of the car

A un cuerpo metálico o chasis del automóvil

Vers corps métallique ou châssis de la voiture

To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition swich)

A un terminal activo del bloque de fusibles conectado a la batería
del automóvil (desviando el interruptor de encendido)

A une borne sous tension du porte-fusible connectée à la batterie de
la voiture (en dérivant l’interrupteur d’allumage)

To an accessory terminal in the fuse block

A un terminal accesorio del bloque de fusibles

Vers borne accessoire du porte-fusible

To remote lead of other equipment or automatic antenna if any

Al conductor remoto de otro equipo o de la antena automática, si hubiere

4

Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il
y en a une

Not included with this unit.

*

No suministrado con esta unidad.

Non fourni avec cet appareil.

Ignition switch

Interruptor de encendido

Interrupteur d’allumage

*

*

Fuse block

Bloque de fusibles

Porte-fusible

White with black stripe

Blanco con rayas
negras

Blanc avec bande noire

White

Blanco

Blanc

Left speaker (front)

Altavoz izquierdo (frontal)

Enceinte gauche (avant)

Gray with black stripe

Gris con rayas negras

Gris avec bande noire

5

Gray

Gris

Gris

Right speaker (front)

Altavoz derecho (frontal)

Enceinte droit (avant)

Green with black stripe

Verde con rayas negras

Vert avec bande noire

3

Green

Verde

Vert

Left speaker (rear)

Altavoz izquierdo (trasero)

Enceinte gauche (arrière)

Purple with black stripe

Púrpura con rayas negras

Violet avec bande noire

Purple

Púrpura

Violet

Right speaker (rear)

Altavoz derecho (trasero)

Enceinte droit (arrière)

PRECAUTIONS on power supply and speaker
connections:

• DO NOT connect the speaker leads of the power cord to the car

battery; otherwise, the unit will be seriously damaged.

• Connect the black lead (ground), yellow lead (to car battery, constant
12 V), and red lead (to an accessory terminal) correctly.

• BEFORE connecting the speaker leads of the power cord to the
speakers, check the speaker wiring in your car.

– If the speaker wiring in your car is as illustrated in Fig. 1 and

Fig. 2 below, DO NOT connect the unit using that original speaker

wiring. If you do, the unit will be seriously damaged.
Redo the speaker wiring so that you can connect the unit to the
speakers as illustrated in Fig. 3.

– If the speaker wiring in your car is as illustrated in Fig. 3, you

can connect the unit using the original speaker wiring in your car.

– If you are not sure of the speaker wiring of your car, consult your

car dealer.

PRECAUCIONES sobre las conexiones de la
fuente de alimentación y de los altavoces:

• NO conecte los conductores de altavoz del cable de alimentación
a la batería de automóvil, pues podrían producirse graves daños
en la unidad.

• Conecte correctamente el conductor negro (a tierra), el conductor
amarillo (a la batería del automóvil, 12 V constantes), y el conductor
rojo (a un terminal de accesorio).

• ANTES de conectar a los altavoces los conductores de altavoz del
cable de alimentación, verifique el conexionado de altavoz de su
automóvil.
– Si el conexionado de altavoz de su automóvil es como se indica

en las Fig. 1 y Fig. 2 de abajo, NO conecte la unidad utilizando
ese conexionado de altavoz original. Si lo hace, se producirán
daños graves en la unidad.
Vuelva a efectuar el conexionado de altavoz de manera que pueda
conectar la unidad a los altavoces de la manera indicada en la Fig.

3.

– Si el conexionado de altavoz de su automóvil es como se indica

+

+

L

-

-

+

+

R

-

-

+

+

L

-

-

+

+

R

-

-

+

+

L

-

-

+

+

R

-

-

en la Fig. 3, podrá conectar la unidad utilizando el conexionado de
altavoz original de su automóvil.

– Si tiene dudas sobre el conexionado de altavoz de su automóvil,

consulte con su concesionario.

Fig. 2 Fig. 3Fig. 1

Connecting the leads / Conexión de los conductores / Raccordement des fils

PRECAUTIONS sur l’alimentation et la
connexion des enceintes:

• NE CONNECTEZ PAS les fils d’enceintes du cordon

d’alimentation à la batterie; sinon, l’appareil serait sérieusement
endommagé.

•

Connectez correctement le fil noir (a la masse), le fil jaune (a la
batterie de la voiture,12 V constant) et le fil rouge (à la prise
accessoire).

•

AVANT de connecter les fils d’enceintes du cordon d’alimentation
aux enceintes, vérifiez le câblage des enceintes de votre voiture.

–

Si le câblage des enceintes de votre voiture est comme
montré sur la Fig. 1 ou Fig. 2 ci-dessous,

PAS l’appareil en utiliscant ce câblage original des enceintes. Si
vous le faites, l’appareil sera sérieusement endommagé.
Recommencez le câblage des enceintes de façon que vous
puissiez connecter l’appareil aux enceintes comme montré sur la
Fig. 3.

–

Si le câblage des enceintes de votre voiture est comme
montré sur la Fig. 3,

vous pouvez connecter l’appareil en

utiliscant ce câblage original d’enceintes pour votre voiture.

– Si vous n’êtes pas sûrs du câblage d’enceintes de votre voiture,

consulter le concessionnaire de votre voiture.

NE CONNECTEZ

Twist the core wires when connecting.

Retuerce los alambres de alma para conectarlos.

Torsader les âmes des fils en les raccordant.

CAUTION / PRECAUCION / PRECAUTION:

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• Para evitar cortocircuitos, cubra los cables NO UTILIZADOS con cinta aislante.

• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS UTILISÉS avec de la bande
isolante.

Solder the core wires to connect them securely.

Suelde los alambres de alma para conectarlos con firmeza.

Souder les âmes des fils pour les raccorder entre eux de
façon sûre.

Connections Adding Other Equipment / Conexiones para añadir otros equipos / Raccordement pour ajouter d’autres appareils

Amplifier / Amplificador / Amplificateur

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of
the other equipment so that it can be controlled through this unit.

• Connect this unit’s line-out terminals to the amplifier’s line-in
terminals.

• Disconnect the speakers from this unit, connect them to the
amplifier. Leave the speaker leads of this unit unused. (Cover the
terminals of these unused leads with insulating tape, as
illustrated above.)

Usted podrá conectar un amplificador para mejorar el sistema estéreo
de su automóvil.

• Conecte el conductor remoto (azul con rayas blancas) al conductor
remoto del otro equipo para poderlo controlar a través de esta
unidad.

• Conecte los terminales de salida de línea de esta unidad con los
terminales de entrada de línea del amplificador.

• Desconecte los altavoces de esta unidad y conéctelos al

amplificador. Los cables de los altavoces de esta unidad quedan
sin usar. (Cubra los terminales de estos cables sin usar con cinta
aislante, tal comose indica en la figura de arriba.)

Vous pouvez connecter un amplificateur pour améliorer votre système
autoradio.

•

Connectez le fil de commande à distance (bleu avec bande blanche)
au fil de commande à distance de l’autre appareil de façon qu’il
puisse être commandé via cet appareil.

•

Raccorder les bornes de sortie ligne de cet appareil aux bornes
d’entrée ligne de l’amplificateur.

• Déconnectez les enceintes de cet appareil et connectez-les à

l’amplificateur. Laissez les fils d’enceintes de cet appareil
inutilisés. (Recouvrir les extrémités de ces fils inutilisés avec de
la bande isolante comme montré ci-dessus.)

Rear speakers

Altavoces posteriores

Enceintes arrière

INPUT

L

R

L

R

JVC Amplifier

Amplificador de JVC

JVC Amplificateur

Signal cord (not supplied with this unit)

Cable de señal (no suministrado con esta unidad)

Cordon de signal (non fourni avec cet appareil)

LINE OUT

L

L

R

R

L

REAR

R

FRONT

KD-S890/

KD-S7350/

KD-S690

Front speakers

Altavoces delanteros

Enceintes avant

Remote lead

Cable remoto

Fil d’alimentation à distance

*2

LL

RR

Only for KD-S890/KD-S7350 : You can connect another power

Solo para KD-S890/KD-S7350 : Podrá conectar otro amplificador de

Seluement pour le KD-S890/KD-S7350 : Vous pouvez connecter un autre

Blue with white stripe

Azul con rayas blancas

Bleu avec bande blanche

INPUT

JVC Amplifier

L

Amplificador de JVC

R

JVC Amplificateur

Y-connector (not supplied with this unit)

Conector en Y (no suministrado con esta unidad)

Connecteur Y (non fourni avec cet appareil)

To automatic antenna if any

A la antena motriz, si la hubiere

Vers l’antenne automatique, s’il y en a une

Front speakers

Altavoces delanteros

Enceintes avant

*2

amplifier for front speakers.

potencia para los altavoces delanteros.

amplificateur de puissance pour les
enceintes avant.

*2 : Firmly attach the ground wire to the metallic body or to

the chasis of the car—to the place not coated with paint
(if coated with paint, remove the paint before attaching
the wire). Failure to do so may cause damage to the
unit.

*2 : Fije firmemente el cable de tierra a la carrocería

metálica o al chasis—a un lugar no cubierto con
pintura (si está cubierto con pintura, quítela antes de
fijar el cable). De lo contrario, se podrían producir
daños en la unidad.

*2 : Attachez solidement le fil de mise à la masse au

châssis métallique de la voiture—à un endroit qui n’est
pas recouvert de peinture (s’il est recouvert de peinture,
enlevez d’abord la peinture avant d’attacher le fil).
L’appareil peut être endommagé si cela n’est pas fait
correctement.

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

• Unit becomes hot.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

LOCALIZACION DE AVERIAS

• El fusible se quema.

* ¿Están los conductores rojo y negro correctamente conectados?

• No es posible conectar la alimentación.

* ¿Está el cable amarillo conectado?

• No sale sonido de los altavoces.

* ¿Está el cable de salida del altavoz cortocircuitado?

• El sonido presenta distorsión.

* ¿Está el cable de salida del altavoz conectado a masa?
* ¿Están los terminales “–” de los altavoces L y R conectados a una

masa común?

• La unidad se calienta.

* ¿Está el cable de salida del altavoz conectado a masa?
* ¿Están los terminales “–” de los altavoces L y R conectados a una

masa común?

4

EN CAS DE DIFFICULTES

• Le fusible saute.

*

Les fils rouge et noir sont-ils racordés correctement?

• L’appareil ne peut pas être mise sous tension.

*

Le fil jaune est-elle raccordée?

• Pas de son des enceintes.

*

Le fil de sortie d’enceinte est-il court-circuité?

• Le son est déformé.

*

Le fil de sortie d’enceinte est-il à la masse?

*

Les bornes “–” des enceintes gauche et droit sont-elles mises
ensemble à la masse?

• L’appareil devient chaud.

*

Le fil de sortie d’enceinte est-il à la masse?

*

Les bornes “–” des enceintes gauche et droit sont-elles mises
ensemble à la masse?

IMPORTANT

Notice the following information will help you to solve your problems.
Keep this IMPORTANT sheet together with the INSTRUCTIONS.

• After installing the unit

= Follow the procedure Å described below.

• If the unit does not operate

= Follow the procedure Å described below.

• If a CD is not ejected from the loading slot

= Follow the procedure ı described below. (If the procedure ı does not work, try the

procedure Å.)

• If a CD is not recognized (“NO DISC” appears on the display) even though
there is a CD in the loading slot

= Follow the procedure ı described below. (If the procedure ı does not work, try the

procedure Å.)

• If a CD is in the unit, it will eject when you reset the unit.
Pay attention not to drop the CD.

Å To reset the microcomputer

While holding SEL (select), press (standby/on/attenuator) for more than 2 seconds.
This will reset the built-in microcomputer.
NOTE: Your preset adjustments—such as preset channels or sound adjustments—will also be

erased.

(standby/on/

attenuator)

SEL (select)

ı To eject a CD by force

While holding (standby/on/attenuator), press 0 (eject) for more than 2 seconds until
the CD is ejected from the loading slot.
(“EJECT” and CD-in indicator flash on the display.)

(standby/on/

attenuator)

0 (eject)

GET0153-001A