JVC KD-S35 User Manual

GET0563-002A

[J]

KD-S35

Installation/Connection Manual
Manual de instalación/conexión

0508DTSMDTJEIN
EN, SP

© 2008 Victor Company of Japan, Limited

ENGLISH

ESPAÑOL

PREPARATIONS

You need the installation kits which corresponds to your car.

• Mark all the check boxes ( ) to make sure you have follow the instructions and the listed parts.

Check the battery system in your car

12 V DC, NEGATIVE ground

Prepare this before installation

Parts list for installation and connection

A/B

Hard case/
Control panel

C

Sleeve

TROUBLESHOOTING

• The fuse blows.
* Are the red and black leads connected correctly?

• Power cannot be turned on.
* Is the yellow lead connected?

• No sound from the speakers.
* Is the speaker output lead short-circuited?

• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

• This unit does not work at all.
* Have you reset your unit?

D

Trim plate

E

Power cord

F

Direct connection
cable for iPod

J

Rubber cushion

INSTALLATION

If you are not sure how to install this unit correctly, consult your JVC car audio dealer.

In dash-mounting

When you stand the unit, be careful

Do the required electrical
connections.

not to damage the fuse on the rear.

G

Washer (ø5)

K

Handles

H

Lock nut (M5)

L

Remote controller

Before removing the unit, release the rear section.

I

Mounting bolt—
M4 × 5 mm (M4 × 1/4");
M5 × 12.5 mm (M5 × 1/2")

M

Battery

Removing the unit

Dashboard

Bend the appropriate tabs
to hold the sleeve firmly
in place.

When using the optional stay

Fire wall

Stay (option)

Screw (option)

Install the unit at an angle of
less than 30˚.

When installing the unit without using the sleeve

In a Toyota car for example, first remove the car radio and install the unit in its place.

Flat type screws
—M5 × 8 mm (M5 × 3/8")*

Bracket*

Flat type screws

Pocket

1

Bracket*

—M5 × 8 mm (M5 × 3/8")*

* Not supplied for this unit.

ELECTRICAL CONNECTIONS

Make sure to disconnect the battery’s negative terminal.

• Be sure to ground this unit to the car’s chassis again after installation.

Note:

It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω).
If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 15 of the INSTRUCTIONS).

High

Heat sink

Typical connections Connecting the external amplifiers and/or subwoofer

Rear line out

Connect only the front speakers if your
speaker system is two-speaker system.

White with black stripe

Front speaker (left)

Front speaker (right)

Rear speaker (left)

White

Gray with black stripe

Gray

Green with black stripe

Green

Purple with black stripe

Rear ground terminalAntenna terminal

15 A fuse
iPod connector

Black

2

Yellow *

Red

Blue with white
stripe

To metallic body or
chassis of the car

To a live terminal in the
fuse block connecting to the
car battery (bypassing the
ignition switch) (constant
12 V)

To an accessory terminal in
the fuse block

To the remote lead of other
equipment or automatic antenna if
any (200 mA max.)

Ignition switch

Fuse block

Set “L/O MODE” to “REAR”

(See page 15 of the
INSTRUCTIONS.)

JVC Amplifier

or

Set “L/O MODE” to “SUB. W”

(See page 15 of the INSTRUCTIONS.)

JVC Amplifier

Subwoofer

Rear speakers

Remote lead

Remote lead

Remote lead (blue with white stripe)

Y-connector *

To the remote lead of other equipment
or automatic antenna if any

Front speakers

1

Rear speaker (right)

Purple

PRECAUTIONS on power supply and speaker connections

You can connect an iPod to this unit using the supplied direct connection cable for iPod.

1

*

Not supplied for this unit.

*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be

turned on.

*3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place not coated with paint (if

coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

*4 Signal cord (not supplied for this unit).

Connecting an Apple iPod

iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

Apple iPod (separately purchased)

Direct connection cable for iPod (supplied)

2