Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
® Audio) Decoding FormatCompact disc playerMax. Bit Rate: 192 kbps
GENERAL
Installation Size182 mm × 52 mm × 160 mm
Panel Size188 mm × 58 mm × 6 mm
(No.MA429<Rev.002>)1-3
Page 4
1.1Safety Precautions
SECTION 1
PRECAUTION
!
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
1-4 (No.MA429<Rev.002>)
Page 5
1.2Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron plate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.3Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the pickup unit.
• Apply solder to the short land before the card wire is disconnected from the connector on the pickup unit.
(If the card wire is disconnected without applying solder, the pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land after connecting the card wire.
Flexible wire
Mechanism control board
CN102
Short land section
Pickup
(No.MA429<Rev.002>)1-5
Page 6
1.5Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation
when open. Do not stare into beam.
(Others) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when
open and inter lock failed or defeated. Avoid direct
exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
!
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS and PRINT
WARNING LABEL and PRINT
1-6 (No.MA429<Rev.002>)
Page 7
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
2.1Identification method
Supported reduction in cost, and board contents was changed.
A set put the following label on is an object.
Front side
Top view
Label position
Change pwb parts
(No.MA429<Rev.002>)1-7
Page 8
SECTION 3
DISASSEMBLY
3.1Main body (Used figure are KD-A305)
3.1.1 Removing the Bottom chassis (See Fig.1, 2)
(1) Remove the two screws A and one screw B attaching the
Heat sink. (See Fig.1)
(2) Remove the two screws C, two screws D and one screw E
attaching the Bottom chassis and then slide to backward
the Bottom chassis. (Se Fig.2)
AAB
Fig.1
3.1.3 Removing the Main board (See Fig.4, 5)
(1) Remove the two screws F and one screw G attaching the
side plate. (See Fig.4)
(2) Remove the three screws H attaching the Main board. (See
Fig.5)
(3) Disconnect the connector CN501
CD mechanism. (See Fig.5)
of the main board from
FFG
Fig.4
hook
E
a
CCDD
Fig.2
3.1.2 Removing the Front chassis (See Fig.3)
(1) Disengage four hooks a engaged both side of the Front
chassis.
Fig.3
CN501
H
H
Fig.5
1-8 (No.MA429<Rev.002>)
Page 9
3.1.4 Removing the CD mechanism (See Fig.6)
(1) Remove the three screws J attaching the CD mechanism.
JJ
J
Fig.6
3.1.5 Removing the Switch board (See Fig.7)
(1) Remove the Volume knob.
(2) Remove the four screws K attaching the Rear cover.
(3) Disengage eleven hooks b engaged Rear cover.
hook
b
KK
hook
b
Fig.7
(No.MA429<Rev.002>)1-9
Page 10
3.1.6 CD MECHANISM assembly section
• Remove the CD MECHANISM assembly from the main body.
Removing the MECHANISM CONTROL BOARD
3.1.7
assembly (See Fig.
(1)
From the bottom side of CD MECHANISM assembly,
remove the solders from the soldered sections (
c
) on the MECHANISM CONTROL BOARD assembly.
1
(See Fig.
(2) Remove the three screws A and one screw B attaching the
MECHANISM CONTROL BOARD assembly. (See Fig.1.)
(3) Solder the short land sections on the pickup. (See Fig.2.)
Caution:
• Solder the short land sections on the pickup before
•
.)
disconnecting the flexible wire from the connector
on the MECHANISM CONTROL BOARD as-
CN102
sembly.
If the card wire is disconnected without attaching
solder, the pickup may be destroyed by static
electricity. (See Fig.
When attaching the MECHANISM CONTROL
BOARD assembly, remove the solders from the
short land sections after connecting the flexible
wire to the connector CN102
CONTROL BOARD assembly.
Mechanism
control board
a
1
and 2)
2
.)
a, b
and
on the MECHANISM
b
CN102
Mechanism control board
CN102
Flexible wire
Short land section
Pickup
Fig.2
A
A
c
A
Fig.1
1-10 (No.MA429<Rev.002>)
B
Page 11
3.1.8 Removing the top cover (See Fig.3 to 5)
• Remove the MECHANISM CONTROL BOARD assembly.
(1) From the front side of the CD MECHANISM assembly,
change the hook position of the two roller springs. (See
Fig.3.)
(2) From the side of the CD MECHANISM assembly, remove
the six screws C attaching the top cover. (See Fig.3 and 4.)
(3) Take out the top cover in an upward direction. (See Fig.5.)
Top cover
C
Roller springRoller spring
Fig.3
Top cover
Fig.5
3.1.9 Removing the roller (See Fig.6)
• Remove the MECHANISM CONTROL BOARD assembly and
top cover.
(1) From the bottom side of the top cover, remove the screw D
attaching the gear holder.
(2) Remove the R.holder assembly from disc plate, and then
take out the roller from R.holder assembly in the direction
of the arrow.
Reference:
When attaching the R.ACT gear (2) and R.ACT gear (3),
apply grease to the section d of R.holder assembly.
Top cover
C
Fig.4
C
Gear holder
Roller gear
R.ACT gear(3)
R.ACT gear(2)
Top cover
D
d
R.holder assembly
Fig.6
Roller coller
Washer
Roller
Disc plate
(No.MA429<Rev.002>)1-11
Page 12
3.1.10 Removing the PHOTO BOARD assembly (See Fig.7 and 8)
• Remove the MECHANISM CONTROL BOARD assembly and
top cover.
(1)
From the bottom side of the top cover, release the
e
projection
Fig.
7
.)
(2) Take out the disc plate in the direction of the arrow. (See
Fig.7.)
(3) From the reverse side of the disc plate, remove the screw
E attaching the PHOTO BOARD assembly. (See Fig.8.)
from the notch of the disc plate. (See
e
e
SUS
spring
Mechanism section
Mecha frame
SUS
spring
F
Top cover
Fig.7
Disc plate
E
Photo board
Disc plate
Fig.8
3.1.11 Removing the mechanism section (See Fig.9 and 10)
• Remove the MECHANISM CONTROL BOARD assembly and
top cover.
From the top side of the CD MECHANISM assembly,
(1)
F
remove the two screws
assembly. (See Fig.
(2) Remove the two roller springs on the top side of the mecha
frame. (See Fig.9.)
(3) Remove the four SUS springs on the top side of the mecha
frame. (See Fig.9.)
(4) Remove the link spring on the top side of the mecha frame.
(See Fig.10.)
(5) Release section f of the three dampers from the mecha
frame. (See Fig.10.)
Reference:
When attaching the roller spring and SUS spring, keep
direction before remove.
Move the slide cam (R) assembly in the direction of the
(6)
arrow, and then take out the mechanism section in an
upward direction. (See Fig.10.)
Reference:
When attaching the mechanism section, apply grease to
the section g. (See Fig.10.)
attaching the loading motor
9
.)
SUS
spring
Roller spring
Loading motor assembly
Fig.9
Damper
Mechanism section
g
f
Fig.10
SUS
spring
Mecha frame
Slidecam(R)
assembly
Link spring
1-12 (No.MA429<Rev.002>)
Page 13
3.1.12 Removing the slide cam (L) (See Fig.11 to 13)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover and mechanism section.
(1) From the top side of the mecha frame, remove the screw G
attaching the cam cover. (See Fig.11.)
Take out the cam cover from mecha frame in an upward
(2)
11
direction. (See Fig.
(3) Take out the slide cam (L) in the direction of the arrow.
(See Fig.12.)
Reference:
When attaching the slide cam (L), apply grease to the
section h. (See Fig.13.)
.)
h
Slide cam(L)
h
h
h
Mecha frame
Slide cam(L)
G
Cam cover
Fig.11
h
Slide cam(L)
h
Fig.13
h
h
Fig.12
Mecha frame
(No.MA429<Rev.002>)1-13
Page 14
3.1.13 Removing the F.lock lever and slide cam (R) (See
Fig.14 and 15)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover and mechanism section.
(1) From the top side of the mecha frame, take out the slide
cam (R) assembly in an upward direction. (See Fig.14.)
(2) Rotate the F.lock lever in the direction of the arrow 1, and
then take out the direction of the arrow 2. (See Fig.14.)
Reference:
When attaching the slide cam (R) assembly, the f.lock
lever and the link arm apply grease to the section
14
(See Fig.
and 15.)
h
Slide cam(R) assembly
h
F.lock lever
2
1
h
h
3.1.14 Removing the damper (See Fig.16)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover and mechanism section.
From the mechanism section, pull out the three dampers in the
direction of the arrow.
Reference:
Before inserting the shaft to the dampers, apply IPA to the
pocket j of damper.
.
Damper (Gray)
Damper (Brown)
j
j
Damper (Brown)
j
Fig.16
Mecha frame
h
h
h
h
Link arm
Fig.14
Slide cam(R) assembly
h
h
h
Slide cam(R) assembly
Fig.15
3.1.15 Removing the clamper assembly (See Fig.17)
• Remove the MECHANISM CONTROL BOARD assembly, top
h
cover and mechanism section.
(1) From the top side of the mechanism section, release the
clamper spring.
(2) Move the clamper assembly in the direction of the arrow,
and then release the joints (k and m).
Take out the clamper assembly from the T.M chassis
(3)
assembly.
h
Clamper assembly
Clamper spring
k
1-14 (No.MA429<Rev.002>)
T.M. chassis assembly
m
Fig.17
Page 15
3.1.16 Removing the feed motor (See Fig.18 and 19)
r
• Remove the MECHANISM CONTROL BOARD assembly, top
cover, mechanism section and clamper assembly.
(1) From the bottom side of the T.M chassis assembly, remove
the two screws H attaching the feed motor assembly. (See
Fig.18.)
Remove the two screws J attaching the feed motor to
(2)
19
f.motor holder. (See Fig.
Reference:
When attaching the f. wheel gear, trigger arm and feed
motor, apply grease to the sections (n, p and q). (See
Fig.18 and 19.)
.)
Feed motor
F.worm gear
q
Comp. spring
J
3.1.17 Removing the SWITCH BOARD assembly (See
Fig.18)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover, mechanism section, clamper assembly and feed motor
assembly.
From the bottom side of the T.M chassis assembly, take out
the SWITCH BOARD assembly in an upward direction from
T.M chassis assembly.
H
Feed motor assembly
Switch board
p
n
F.wheel gear
Trigger arm
F.motor holder
Fig.19
3.1.18 Removing the loading motor (See Fig.20)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover, mechanism section and clamper assembly.
(1) From the right side of the L.M base assembly, remove the
two screws K attaching the loading motor.
(2) Take out the loading motor in the direction of the arrow
from the L.M base assembly.
Reference:
When attaching the loading motor, apply grease to the
section r.
K
r
L.M. base assembly
Fig.20
L.worm gear
Loading moto
T.M. chassis assembly
Fig.18
(No.MA429<Rev.002>)1-15
Page 16
3.1.19 Removing the pickup assembly (See Fig.21 to 22)
• Remove the MECHANISM CONTROL BOARD assembly, top
cover, mechanism section, clamper assembly and feed motor
assembly.
Caution:
• Do not touch section u on the pickup assembly. (See Fig.21
and 22.)
(1) From the bottom side of the T.M chassis assembly, move
the pickup assembly in the direction of the arrow from the
T.M chassis assembly. (See Fig.21.)
(2) Pull out the main shaft. (See Fig.21.)
(3) Remove the screw M attaching the pickup to the rack plate.
(See Fig.22.)
Reference:
When attaching the loading motor, apply grease to the
sections s and t. (See Fig.21.)
3.1.20 Removing the spindle motor (See Fig.23 and 24)
Remove the MECHANISM CONTROL BOARD assembly,
•
top cover, mechanism section, clamper assembly, feed motor
assembly and pickup assembly.
(1) From the top side of the T.M chassis assembly, remove the
CD T.table assembly from the spindle motor. (See Fig.23.)
(2) Remove the two screws N attaching the spindle motor.
(See Fig.23.)
(3) Take out the spindle motor from the bottom side of the T.M
chassis assembly. (See Fig.23.)
Reference:
When attaching the CD T.table assembly to the spindle
motor shaft, apply loctite 460 to inside the CD T.table
assembly. (See Fig.24.)
Pick up assembly
s
T.M. chassis assembly
u
Fig.21
t
Main shaft
NN
Spindle motor
Fig.23
CD T.table assembly
CD T.table assembly
T.M.chassis assembly
Loctite
M
Rack plate
u
Pick up
Fig.22
1-16 (No.MA429<Rev.002>)
Spindle motor
Fig.24
Page 17
SECTION 4
ADJUSTMENT
4.1Adjustment
Test instruments required for adjustment
(1) Digital oscilloscope (100MHz)
(2) Digital tester
(3) Test Disc
(4) Extension cable : EXTGS004-26PL
Standard volume position
Balance and Bass &Treble volume : lndication "0"
Loudness : OFF
How to connect the extension cable for adjusting
Be sure to attach the het sink and rear bracket onto the power amplifier IC and regulator IC respectively,
before supply the power.
If voltage is applied without attaching these parts, the power amplifier IC and regulator IC will be destroyed by heat.
Standard measuring conditions
Power supply voltage DC 14.4V(10.5 to 16V)
Load impedance 20K ohm (2 Speakers connection)
Dummy load
Exclusive dummy load should be used for AM, and FM.
For FM dummy load, there isa loss of 6dB between SSG
output and antenna input.
The loss of 6dB need not be considered since direct
reading of figures are applied in this working standard.
Extension cable
EXTGS004-26PL
(No.MA429<Rev.002>)1-17
Page 18
4.2SERVICE MODE
DELEPROM
CD ERROR
CLR ERR
RUNNING1
RUNNING2
SIRIUS RST
XM RST
HD RESET
Clear EEPROM data
Display the CD Error past record in EEPROM.
Clear CD Error history from EEPROM.
For use in running tests.
For use in running tests.
SIRIUS Soft Reset
It clears all contents of built-in RAM and EEPROM, and performs software reset.
* Active at the time of SIRIUS connection.
XM Soft Reset
It clears all contents of built-in RAM and EEPROM, and performs software reset.
* Active at the time of XM connection.
HD Soft Reset
It clears all contents of built-in RAM and EEPROM, and performs software reset.
* Active at the time of HD connection.
DAB RESET
BT RESET
CDCHERR
DELCHERR
DAB Soft Reset
It clears all contents of built-in RAM and EEPROM, and performs software reset.
* Active at the time of DAB connection.
BT Soft Reset
It clears all contents of built-in RAM and EEPROM, and performs software reset.
* Active at the time of BT connection.
Display the CH Error past record stored in EEPROM
* Active at the time of CD CHANGER/IPOD (JBUS) connection
Clear CH Error history from EEPROM
* Active at the time of CD CHANGER/IPOD (JBUS) connection
1-18 (No.MA429<Rev.002>)
Page 19
4.3TUNER SERVICE MODE
A
Key operation (FM, AM and DAB mode)
Enter service mode: [SEL] [MENU] (3 sec)
Exit service mode: press [ENTER] (SEL) key.
Go to next item: press [DISP] key
Back to previous item: press [BACK] key
VER=#***MICON version display
# indicates destination: J=USA, U=OTHERS (eg. ASIA), R=EUROPE, E=EASTERN EUROPE
*** indicates version No.
########
Tuner device and version identification display
Display :TOM V1 for TOMIC V1 tuner.
Display :TOM V2 for TOMIC V2 tuner.
Display :ATOM V2 for ATOMIC V2 tuner.
Display: ATOM V3 for ATOMIC V3 tuner.
TINJ= ##
SPI=####
PI =####
PTY=##
TP=#TA=*
MS=#DI=*
AF=####
LEV= ##H
U&W= ##H
Tuner injection indicator
"##" indicates current tuner injection.
FOR DAB ONLY
To link SID display that DAB receives and FM station (Search PI), the reception situation of D
displayed.
"####" indicates SID code.
FOR RDS ONLY
PI display of receiving station, "####" indicates PI code.
PTY display of receiving station (00~29), "##" indicates PTY code.
TP, TA display of receiving station
"#" indicates TP ON/OFF: 1=ON; 0=OFF;
"*" indicates TA ON/OFF: 1=ON; 0=OFF.
M/S, DI display of receiving station
"#" indicates M/S ON/OFF: 1=ON; 0=OFF;
"*" indicates DI ON/OFF: 1=ON; 0=OFF.
Display the contents of AF memory (by scrolling) "####" indicate AF frequencies.
Fieldstrength indicator.
Adjacent and Multipath noise level indicator.
IFC= ##H
IFBW= #
RFAGC=##
IFAGC=##
##**
########
IF COUNTER result indicator.
FM IF filter bandwidth indicator.
FM RF AGC resulting attenuation.
FM IF AGC resulting attenuation.
CLOCK display of receiving station (Original DISP key operation)
FOR RDS ONLY
PS NAME display of receiving station (Original DISP key operation)
#####
FREQUENCY display of receiving station (Original DISP key operation)
(No.MA429<Rev.002>)1-19
Page 20
4.4ERROR CODE
4.4.1 Mechanical Error Detail Codes
ConditionDetailsError Code Detail Code
Disc Loading Error
(1) B1 Time OutAfter detecting SW1=L, it does not become SW2=L090011
(2) B2 Time OutAfter detecting SW2=H, it does not become SW2=L090012
(3) C1 Time OutAfter detecting SW2=L, it does not become SW2=H090013
Eject Error
(1) B1 Time OutAfter detecting SW2=H, it does not become SW2=L010021
(2) C2 Time OutAfter detecting SW2=L, it does not become SW2=H010022
(3) B2 Time OutAfter detecting SW1=L, it does not become SW2=L
010023
immediately after RESET and so on.
(4) D0 Panel CloseDisc can not be ejected due to closed panel.010024
Forced Eject Error
(1) E1 ErrorSW1=H, SW2=L detected from NO DISC010041
(2) E2 ErrorDetected SW1=L after RESET and then detected SW1=H010042
(3) E3 ErrorDetected SW1=H after RESET010043
(4) E4 ErrorDetected SW1=H after SW1=L010044
(5) E5 ErrorDetected SW1=H after SW2=H→L010045
(6) E6 ErrorTime Out for Loading after RESET010046
(7) E7 ErrorDetected SW1=H after SW2=H→L→H010047
(8) E8 ErrorEject Key input while the procedure is not completed after
010048
Forced Eject execution
(9) ErrorEject Key input during Disc is on the way and not completed010049
Loading Waiting Error
(1) SW1=H or NO DISC
Disc is removed or NO DISC detection condition090031
detection before Loading
Motor activation during
Disc is waiting at thewaiting location.
(2) SW2=L before Loading
Disc is inserted090032
Motor activation during
Disc is waiting at thewaiting location.
4.4.2 CD changer mechanism error code
Error contentsDetailsError code Detail code
Tray eject error Tray motor time over
1.TRAYINSW time over
Tray motor does not operate.030011
(TRAYINSW:LTRAYOUTSW:H)
2.TRAYOUTSW time over
Tray stops.030012
(TRAYINSW:HTRAYOUTSW:H)
3.TRAYINSW time over
TRAYINSW NG etc.030013
(TRAYINSW:LTRAYOUTSW:L)
4.MAGIN SW:L→H Magazine is ejected while Tray is being ejected.030014
Tray return error Tray motor time over
1.TRAYOUTSW time over
Tray motor does not operate.030016
(TRAYINSW:HTRAYOUTSW:L)
2.TRAYINSW time over
Tray stops.030017
(TRAYINSW:HTRAYOUTSW:H)
3.TRAYIN/OUTSW time over
TRAYOUTSW NG etc.030018
(TRAYINSW:LTRAYOUTSW:L)
4.MAGIN SW:L→H Magazine is ejected while Tray is being returned.030019
1-20 (No.MA429<Rev.002>)
Page 21
Lifter up error Position motor time over
1.WAIT position time over Position motor does not operate.020021
2.WAIT position time over Position is not stable in fine adjustment mode.020022
3.WAIT position time over Other condition020023
Lifter down error Position motor time over
1.WAIT position time over Position motor does not operate.020026
2.WAIT position time over Position is not stable in fine adjustment mode.020027
3.WAIT position time over Other condition020028
Chucking error Position motor time over
1.Play position time over Position motor does not operate.020031
2.Play position time over Position is not stable in fine adjustment mode.020032
3.Play position time over Other condition020033
Unchucking error Position motor time over
1.WAIT position time over Position motor does not operate.020036
2.WAIT position time over Position is not stable in fine adjustment mode.020037
3.WAIT position time over Other condition020038
Eject error Eject cannot be carried out.
1.Eject position time over Position motor does not operate.020041
2.Eject position time over Improper EJECT position.*020042
3.MAGINSW time over Magazine is not ejected.010043
Initialize error
1.Mechanism SW NG error TRAYINSW and TRAYOUTSW are L.030046
2.Absolute position time over Position is not stable in absolute position.*020047
*"Position is not stable in WAIT position," "Position is not stable in PLAY position," and "Position is not stable in
absolute position" and "Improper EJECT position" are all Position Motor TIME OVER.
4.4.3 CD changer disc error code
Error contentsDetailsError code Detail code
Pickup movement error Time over at PUBWD and PUFWD by monitoring RESET SW.
1.Time over of pickup movement
in an inner direction(10s)
2.Time over of pickup movement
in an outer direction(10s)
Focus search error
Focus is not adjusted by 3-round fo-
Pickup cannot move in an inner direction.
RESET SW is not on.
Pickup cannot move in an outer direction.
RESET SW is not off.
When focus is not adjusted by 3-round(1set)
focus search after disc change or focus shock the result is NG
040051
040052
810053
cus search
Tracking balance adjustment error
Time over(1s)
TOC area search error
Tracking balance adjustment is not finished 1s
820054
after adjustment command(TBA) is executed.
TOC area search is not finished after 10s.800055
Time over(10s)
Focus balance adjustment error
Time over(2s)
Focus gain adjustment error
Time over(0.6s)
Focus balance adjustment is not finished 2s
after adjustment command(FBA) is executed.
Focus gain adjustment error is not finished 0.6s
after adjustment command(FGA) is executed.
820056
820057
TOC read error. Time over(30s) TOC read operation is not finished after 30s.840059
First track access error
Time over(10s)
Last track access error
First track access is not finished 10s after TOC
800060
reading is finished.
Last track access is not finished 10s after first track in running mode.800061
Time over(10s)
Q code read error
Time over(0.6s)
Q code is not read for 0.6s during playback of
TOC and program area.
M3MM P3 FSPG4002-001 ------------ POLY BAG (Deletion)1 01,02,03,04,05,06,07,08,09,0A,0B
M3MM P3 ------------ FSPG4002-001 POLY BAG (Addition)1 01,02,03,05,06,07,09,0A,0B,0C
M3MM P3 ------------ FSPG4002-001 POLY BAG (Addition)2 04,08
M3MM P4 FSPG4002-001 ------------ POLY BAG (Deletion)1 04,08
<Rev.001> <Rev.002>
Part No.
Part Name Description QtyModels
(Addition)1 01
SLEEVE
(Deletion)1 01,02,03,04,05,06,07,08,09,0A,0B
SLEEVE
(Addition)1 02,03,04,05,06,07,08,09,0A,0B,0C
SLEEVE
(Addition)1 01
KIT
(Deletion)1 01,02,03,04,05,06,07,08,09,0A,0B
KIT
(MA429-R002) 11
Page 36
Victor Company of Japan, Limited
Mobile Entertainment Division 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(MA429-R002)
Printed in Japan
No.MA429<Rev.001> VSE
Page 37
PARTS LIST
KD-A305J,KD-R300J,KD-R404UI
KD-R405U,KD-R405UN,KD-R405UT
KD-R405UH,KD-R406U,KD-R406UN
KD-R406UT,KD-R406UH,KD-S26J
MODELMARK
AKD-A305J
DKD-R405U
GKD-R405UH
JKD-R406UT
* All printed circuit boards and its assemblies are not available as service parts.
MODELMARK
BKD-R300J
EKD-R405UN
HKD-R406U
KKD-R406UH
MODELMARK
- Contents -
Exploded view of general assembly and parts list (Block No.M1)
CD mechanism assembly and parts list (Block No.MB)
Electrical parts list (Block No.01~05)
Packing materials and accessories parts list (Block No.M3)
CKD-R404UI
FKD-R405UT
IKD-R406UN
LKD-S26J
3- 2
3- 6
3- 8
3-16
MA429PAR<Rev.002>
3-1
Page 38
Exploded view of general assembly and parts list
3
0
5
Block No.
MMM1
405UT,406UT
53
13
12
1
e
a
12
14
5
d
a
c
e
b
A
6
17
16
19
18
49
9
56
26J
305J,
2
6
35
Switch
board
24
33
34
28
29
6
23
31
32
26
27
25
52
30
21
22
36
36
1
36
37
40
42
39
3-2
Page 39
MM
305J,300J,26J
48
305J
45
47
d
b
46
c
Main board
36
37
20
15
f
26J
7
55
7
7
8
54
8
8
4
2
A
11
10
305J
38
43
3
50
41
51
f
0
305J,300J
41
44
The parts without symbol number are not service.
3-3
Page 40
General Assembly
Block No. [M][1][M][M]
Symbol No.Part No.Part NameDescriptionLocal
1GE10248-001ATOP CHASSISA
1GE10248-003ATOP CHASSISB,C,D,E,F,G,H,I,J,K,L
2GE33323-002AHEAT SINKA,B,C,D,E,F,G,H,I,J,K
2GE33323-001AHEAT SINKL
3GE20248-002ABOTTOM COVERA
3GE20248-001ABOTTOM COVERB,C,D,E,F,G,H,I,J,K,L
4GE33325-002AINSULATORA,B,C,D,E,F,G,H,I,J,K
4GE33325-003AINSULATORL
5GE40395-001ASIDE PANEL
6QYSDST2604ZATAP SCREWM2.6 x 4mm(x3)
7GE40377-002ASCREW(x3)
8GE40377-003ASCREW(x3)
9QYSDST2606ZATAP SCREWM2.6 x 6mm
10QYSDST2606ZATAP SCREWM2.6 x 6mm
11QYSDSF2606ZATAP SCREWM2.6 x 6mm
12GE40377-002ASCREW(x2)
13QYSDST2608ZATAP SCREWM2.6 x 8mm
14QYSDST2606ZATAP SCREWM2.6 x 6mm
15GE10242-005AFRONT CHASSISA,B,C,D,E,F,G,H,I,J,K
15GE10242-008AFRONT CHASSISL
16GE32350-002ALOCK LEVER
17GE40368-002ATORSION SPRING
18GE32810-001ARELEASE LEVER
19GE30999-004ACOMP.SPRING
20GE40432-001ABLIND
21GE10243-011AFRONT PANELA
21GE10243-010AFRONT PANELB,L
21GE10243-012AFRONT PANELC,D,E,F,G
21GE10243-013AFRONT PANELH,I,J,K
22GE33342-022AFINDER ASSYA
22GE33342-024AFINDER ASSYB
22GE33342-006AFINDER ASSYC
22GE33342-005AFINDER ASSYD,E,F,G
22GE33342-015AFINDER ASSYH,I,J,K
22GE33342-038AFINDER ASSYL
23GE33307-001APOWER BTN
24GE33308-001AEJECT BTN
25GE33309-004ADISP BTN HIA,B,L
25GE33309-005ADISP BTN HIC,D,E,F,G,H,I,J,K
26GE33310-004ASRC BTN HIA,B,L
26GE33310-005ASRC BTN HIC,D,E,F,G,H,I,J,K
27GE33311-001AMENU BTN HI
28GE33315-003ADETACH BTNA,B,H,I,J,K,L
28GE33315-001ADETACH BTNC,D,E,F,G
29GE30999-006ACOMP.SPRING
30GE33314-002ALIGHT GUIDE
31GE33312-006ANAVI BTN HIA,B,H,I,J,K,L
31GE33312-005ANAVI BTN HIC,D,E,F,G
32GE33313-002ANAVI BTN BASE
33GE33320-003AVOL KNOBA
33GE33320-001AVOL KNOBB,C,D,E,F,G,H,I,J,K,L
34GE40127-005AKNOB SPRING
35GE10244-001AREAR COVERA,B,C,D,E,F,G,H,I,J,K
35GE10244-003AREAR COVERL
36VKZ4777-010M INI SCREW(x4)
37GE33317-001ALCD LENS
38GE33318-001ALENS CASE
39GE33319-001ALCD CASE
40GE40440-003ALIGHTING SHEET
41GE33394-002ANAME PLATEA
41GE33397-002ANAME PLATEB
41GE33403-001ANAME PLATEC
41GE33400-001ANAME PLATED,E,F,G
41GE33406-001ANAME PLATEH,I,J,K
41GE33872-001ANAME PLATEL
42QLD0569-001LCD MODULE
43QNZ1002-001RUBBER CONNECTO
44QNZ1003-001RUBBER CONNECTO
C1NCB31HK-102XC CAPACITOR1000pF 50V K
C2NDC31HJ-7R0XC CAPACITOR7pF 50V J
C3NCB31HK-102XC CAPACITOR1000pF 50V K
C4NCB31AK-224XC CAPACITOR0.22uF 10V K
C5NDC31HJ-150XC CAPACITOR15pF 50V J
C6NDC31HJ-2R0XC CAPACITOR2pF 50V J
C7NDC31HJ-220XC CAPACITOR22pF 50V J
C10NCB21AK-105XC CAPACITOR1uF 10V K
C11NCB31HK-103XC CAPACITOR0.01uF 50V K
C12NCB31HK-103XC CAPACITOR0.01uF 50V K
C13NCB21AK-105XC CAPACITOR1uF 10V K
C14NCB31AK-224XC CAPACITOR0.22uF 10V K
C15NCB31CK-104XC CAPACITOR0.1uF 16V K
C16NCB31HK-103XC CAPACITOR0.01uF 50V K
C17NCB31CK-104XC CAPACITOR0.1uF 16V K
C18NCB31HK-103XC CAPACITOR0.01uF 50V K
C19NCB31CK-104XC CAPACITOR0.1uF 16V K
C22NDC31HJ-150XC CAPACITOR15pF 50V J
C23NCB31CK-104XC CAPACITOR0.1uF 16V K
C24NCB31HK-103XC CAPACITOR0.01uF 50V K
C25NCB31HK-103XC CAPACITOR0.01uF 50V K
C26QEKJ1CM-107ZE CAPACITOR100uF 16V M
C27QEKJ1EM-106ZE CAPACITOR10uF 25V M
C34NDC31HJ-5R6XC CAPACITOR5.6pF 50V J
C120NCB31CK-104XC CAPACITOR0.1uF 16V K
C161NCB31AK-105XC CAPACITOR1uF 10V K
C162QTE1H57-105ZE CAPACITOR1uF 50V
C163QTE1H57-105ZE CAPACITOR1uF 50V
C164NCB31AK-105XC CAPACITOR1uF 10V K
C165NCB31HK-103XC CAPACITOR0.01uF 50V K
C166NCB31AK-105XC CAPACITOR1uF 10V K
C169NCB31EK-103XC CAPACITOR0.01uF 25V K
C171NCB31AK-105XC CAPACITOR1uF 10V K
C172QTE1H57-105ZE CAPACITOR1uF 50V
C173QTE1H57-105ZE CAPACITOR1uF 50V
C174NCB31AK-105XC CAPACITOR1uF 10V K
C175NCB31HK-103XC CAPACITOR0.01uF 50V K
C180QTE1A57-107ZE CAPACITOR100uF 10V
C181QTE1C57-106ZE CAPACITOR10uF 16V
C301QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C302QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C303NDC31HJ-101XC CAPACITOR100pF 50V J
C304NDC31HJ-101XC CAPACITOR100pF 50V J
C311QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C312QFV91HJ-474ZMF CAPACITOR0.47uF 50V J
C313NDC31HJ-101XC CAPACITOR100pF 50V J
C314NDC31HJ-101XC CAPACITOR100pF 50V J
C315NCB31AK-105XC CAPACITOR1uF 10V K
C316NCB31AK-105XC CAPACITOR1uF 10V K
C317QTE1C57-476ZE CAPACITOR47uF 16V
C318QEKJ1CM-226ZE CAPACITOR22uF 16V M
C319NCB31EK-223XC CAPACITOR0.022uF 25V K
C320NCB31EK-223XC CAPACITOR0.022uF 25V K
C321NCB21AK-225X-AC CAPACITOR2.2uF 10V K
C383QEKJ1HM-475ZE CAPACITOR4.7uF 50V MA
C384QEKJ1HM-475ZE CAPACITOR4.7uF 50V MA
C385QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C386QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C387NCB31HK-152XC CAPACITOR1500pF 50V K A
C388NCB31HK-152XC CAPACITOR1500pF 50V K A
C389QEKJ1CM-107ZE CAPACITOR100uF 16V MA
C390QEKJ1CM-107ZE CAPACITOR100uF 16V MA
C392NCB31EK-104XC CAPACITOR0.1uF 25V KA
C393QEKJ1CM-476ZE CAPACITOR47uF 16V MA
C501QEKJ0JM-227ZE CAPACITOR220uF 6.3V M
C503QEKJ1AM-227ZE CAPACITOR220uF 10V M
C504NCB31EK-104XC CAPACITOR0.1uF 25V K
C505NCB31EK-104XC CAPACITOR0.1uF 25V K
C507NCB31EK-473XC CAPACITOR0.047uF 25V K
Part No.Part NameDescriptionLocal
3-8
Page 45
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C511NCB31HK-222XC CAPACITOR2200pF 50V K
C513NCB31HK-682XC CAPACITOR6800pF 50V K
C515NCB31HK-122XC CAPACITOR1200pF 50V K
C517NCB31HK-182XC CAPACITOR1800pF 50V K
C518NDC31HJ-680XC CAPACITOR68pF 50V J
C521NCB31EK-104XC CAPACITOR0.1uF 25V K
C522NCB31CK-224XC CAPACITOR0.22uF 16V K
C524NDC31HJ-561XC CAPACITOR560pF 50V J
C525NCB31CK-223XC CAPACITOR0.022uF 16V K
C526NCB31CK-223XC CAPACITOR0.022uF 16V K
C527NCB31EK-332XC CAPACITOR3300pF 25V K
C528NDC31HJ-181XC CAPACITOR180pF 50V J
C529NCB31HK-103XC CAPACITOR0.01uF 50V K
C530NCB31HK-103XC CAPACITOR0.01uF 50V K
C531NCB31AK-334XC CAPACITOR0.33uF 10V K
C532NCB31AK-334XC CAPACITOR0.33uF 10V K
C534NCB31EK-332XC CAPACITOR3300pF 25V K
C535NCB31EK-104XC CAPACITOR0.1uF 25V K
C536QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C537QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C539NCB31EK-104XC CAPACITOR0.1uF 25V K
C540NCS31HJ-681XC CAPACITOR680pF 50V J
C541NCB31EK-153XC CAPACITOR0.015uF 25V K
C542NCB31EK-104XC CAPACITOR0.1uF 25V K
C543NCB31HK-102XC CAPACITOR1000pF 50V K
C544NCB31EK-823XC CAPACITOR0.082uF 25V K
C545NCB31EK-104XC CAPACITOR0.1uF 25V K
C547QTE0J57-476ZE CAPACITOR47uF 6.3V
C548QTE0J57-476ZE CAPACITOR47uF 6.3V
C549NCB31EK-104XC CAPACITOR0.1uF 25V K
C551NCB31EK-104XC CAPACITOR0.1uF 25V K
C552QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C583NDC31HJ-821XC CAPACITOR820pF 50V J
C584NDC31HJ-821XC CAPACITOR820pF 50V J
C585QTE1H64-225ZE CAPACITOR2.2uF 50V
C586QTE1H64-225ZE CAPACITOR2.2uF 50V
C587NDC31HJ-151XC CAPACITOR150pF 50V J
C588NDC31HJ-151XC CAPACITOR150pF 50V J
C590QTE0J57-476ZE CAPACITOR47uF 6.3V
C591QTE1A57-107ZE CAPACITOR100uF 10V
C592NCB31EK-104XC CAPACITOR0.1uF 25V K
C703NDC31HJ-200XC CAPACITOR20pF 50V J
C704NDC31HJ-200XC CAPACITOR20pF 50V J
C706NCB31EK-103XC CAPACITOR0.01uF 25V K
C707QEKJ1CM-107ZE CAPACITOR100uF 16V M
C708NCB31CK-104XC CAPACITOR0.1uF 16V K
C709NCB31CK-104XC CAPACITOR0.1uF 16V K
C710NDC31HJ-101XC CAPACITOR100pF 50V JA
C711QTE0J57-476ZE CAPACITOR47uF 6.3V
C712NCB31EK-103XC CAPACITOR0.01uF 25V K
C714NCB31CK-104XC CAPACITOR0.1uF 16V K
C715NCB31CK-104XC CAPACITOR0.1uF 16V K
C717NCB31CK-104XC CAPACITOR0.1uF 16V K
C718NCB31CK-104XC CAPACITOR0.1uF 16V K
C719QEKJ1CM-107ZE CAPACITOR100uF 16V M
C720NCB31AK-474XC CAPACITOR0.47uF 10V K
C721NCB31CK-104XC CAPACITOR0.1uF 16V K
C722QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C726NDC31HJ-391XC CAPACITOR390pF 50V J
C727NDC31HJ-391XC CAPACITOR390pF 50V J
C741NDC31HJ-680XC CAPACITOR68pF 50V J
C771NCB31EK-473XC CAPACITOR0.047uF 25V K
C781QEKJ1AM-227ZE CAPACITOR220uF 10V M
C784QEKJ1CM-107ZE CAPACITOR100uF 16V M
C785QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C801NCB31EK-473XC CAPACITOR0.047uF 25V K
C852NCB31CK-224XC CAPACITOR0.22uF 16V KC,D,E,F,G,
C901QEZ0870-278E CAPACITOR2700uF
C902QERF1HM-225ZE CAPACITOR2.2uF 50V M
C903QEKJ1CM-476ZE CAPACITOR47uF 16V M
C905QEKJ1CM-476ZE CAPACITOR47uF 16V M
C906NCB31HK-103XC CAPACITOR0.01uF 50V K
C908QEKJ1AM-227ZE CAPACITOR220uF 10V M
C909QERF0JM-337ZE CAPACITOR330uF 6.3V M
C912NCB31HK-103XC CAPACITOR0.01uF 50V K
C916NCB31HK-103XC CAPACITOR0.01uF 50V K
C971NCB31EK-104XC CAPACITOR0.1uF 25V K
H,I,J,K
C982NCB31EK-104XC CAPACITOR0.1uF 25V K
C984NCB21AK-225XC CAPACITOR2.2uF 10V K
C603NCB31CK-104XC CAPACITOR0.1uF 16V K
C604NCB31CK-105XC CAPACITOR1uF 16V K
C650NCB31CK-104XC CAPACITOR0.1uF 16V K
C651NBE21CM-106XTA E CAPACITOR10uF 16V M
C661NCB31CK-105XC CAPACITOR1uF 16V K
C662NDC31HJ-151XC CAPACITOR150pF 50V J
C663NCB31CK-223XC CAPACITOR0.022uF 16V K
C665NCB31CK-104XC CAPACITOR0.1uF 16V K
C666NCB31CK-104XC CAPACITOR0.1uF 16V K
C682NCB31EK-104XC CAPACITOR0.1uF 25V K
C703NDC31HJ-200XC CAPACITOR20pF 50V J
C704NDC31HJ-200XC CAPACITOR20pF 50V J
C706NCB31EK-103XC CAPACITOR0.01uF 25V K
C707QEKJ1CM-107ZE CAPACITOR100uF 16V M
C708NCB31CK-104XC CAPACITOR0.1uF 16V K
C709NCB31CK-104XC CAPACITOR0.1uF 16V K
C710NDC31HJ-101XC CAPACITOR100pF 50V JA
C711QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C714NCB31CK-104XC CAPACITOR0.1uF 16V K
C715NCB31CK-104XC CAPACITOR0.1uF 16V K
C717NCB31CK-104XC CAPACITOR0.1uF 16V K
C718NCB31CK-104XC CAPACITOR0.1uF 16V K
C719QEKJ1CM-476ZE CAPACITOR47uF 16V M
C720NCB31AK-474XC CAPACITOR0.47uF 10V K
C721NCB31CK-104XC CAPACITOR0.1uF 16V K
C722QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C741NDC31HJ-680XC CAPACITOR68pF 50V J
C781QEKJ1CM-476ZE CAPACITOR47uF 16V M
C784QEKJ1CM-107ZE CAPACITOR100uF 16V M
C785QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C801NCB31EK-473XC CAPACITOR0.047uF 25V K
C852NCB31CK-224XC CAPACITOR0.22uF 16V KC,D,E,F,G,H,I
C901QEZ0870-278E CAPACITOR2700uF
C903QEKJ1CM-476ZE CAPACITOR47uF 16V M
C904NCB31HK-104XC CAPACITOR0.1uF 50V K
C905QEKJ1CM-476ZE CAPACITOR47uF 16V M
C906NCB31HK-103XC CAPACITOR0.01uF 50V K
C908QEKJ1CM-476ZE CAPACITOR47uF 16V M
C909QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C912NCB31HK-103XC CAPACITOR0.01uF 50V K
C916NCB31HK-103XC CAPACITOR0.01uF 50V K
C971NCB31EK-104XC CAPACITOR0.1uF 25V K
C982NCB31EK-104XC CAPACITOR0.1uF 25V K
C984NCB21AK-225XC CAPACITOR2.2uF 10V K
L1NQL093K-R47XCOIL0.47uH K
L2NQL093K-1R8XCOIL1.8uH K
L3QQL213M-R22ZCOIL0.22uH M
L4QQR1813-001COIL
L5QQL244J-561ZCOIL560uH J
L6QQL244J-561ZCOIL560uH J
L7QQL244K-4R7ZCOIL4.7uH K
L8QQL244K-4R7ZCOIL4.7uH K
L120NQR0007-002XFERRITE BEADS
L121NQR0007-002XFERRITE BEADS
L122NQR0007-002XFERRITE BEADS
L701QQL244K-4R7ZCOIL4.7uH K
L702QQL244K-4R7ZCOIL4.7uH K
L901QQR1852-001CHOKE COIL
L901or QQR0703-001CHOKE COIL
C604NCB31CK-105XC CAPACITOR1uF 16V K
C650NCB31CK-104XC CAPACITOR0.1uF 16V K
C651NBE21CM-106XTA E CAPACITOR10uF 16V M
C661NCB31CK-105XC CAPACITOR1uF 16V K
C662NDC31HJ-151XC CAPACITOR150pF 50V J
C663NCB31CK-223XC CAPACITOR0.022uF 16V K
C665NCB31CK-104XC CAPACITOR0.1uF 16V K
C666NCB31CK-104XC CAPACITOR0.1uF 16V K
C682NCB31EK-104XC CAPACITOR0.1uF 25V K
No additional / supplemental order of WARRANTY CARDs are available.
Block No.
M
3
M
M
305J
KIT : A9,A10,A11
A12,A13
P5
405U,406U
P3
A1,A2,A4,A5,A6,A21
305J,300J,26J
P3
P5
A13
A16
A15
A17
P3
A1,A4,A21
A8
A7
305J,300J,26J
P9
A14
P2
P7
P8
P6
405U,406U
P4
A1,A4,A18,A19
A20,A21,A22(26J)
3-16
P6
The
A3
P1
arts without symbol number are not service.
Page 53
Packing and Accessories
Block No. [M][3][M][M]
Symbol No.Part No.Part NameDescriptionLocal
A 1GET0570-001AINST BOOKENG FRE SPAA,B
A 1GET0572-001AINST BOOKENGC
A 1GET0571-001AINST BOOKENG THAD,G,H,K
A 1GET0571-004AINST BOOKENG INAE,I
A 1GET0571-005AINST BOOKENG CHI(TAIWAN)F,J
A 1GET0642-001AINST BOOKENG FRE SPAL
A 2GET0571-003AINST BOOKRUSD,H
A 3GET0571-002AINST BOOKARA KOR CHI(TAIWAN) PERD,H
A 4GET0570-002AINSTALL MANUALENG FRE SPAA
A 4GET0570-002BINSTALL MANUALENG FRE SPAB
A 4GET0572-002BINSTALL MANUALENGC
A 4GET0571-006BINSTALL MANUALENG THAD,G,H,K
A 4GET0571-009BINSTALL MANUALENG INAE,I
A 4GET0571-010BINSTALL MANUALENG CHI(TAIWAN)F,J
A 4GET0642-002AINSTALL MANUALENG FRE SPAL
A 5GET0571-007BINSTALL MANUALARA KOR CHI(TAIWAN) PERD,H
A 6GET0571-008BINSTALL MANUALRUSD,H
A 7GE20137-003AMOUNTING SLEEVEA
A 7GE20137-008AMOUNTING SLEEVEB,C,D,E,F,G,H,I,J,K,L
A 8GE20235-001ATRIM PLATEA,B,H,I,J,K
A 8GE20235-012ATRIM PLATEC,D,E,F,G
A 8GE20235-014ATRIM PLATEL
A 9VKZ4027-202PLUG NUTA
A 10GE40426-002AMOUNT BOLTA
A 11VKZ4328-003LOCK NUTA
A 12QYWWS53A008ZAWASHER0mm/5.3mm x A
A 13GE40130-002AHOOK(x2)
A 14GE32320-001AHARD CASE ASSYC,D,E,F,G,H,I,J,K
A 15RM-RK50CREMOCONA,B,C,D,E,F,H,I,J,L
A 15RM-RK50IREMOCONG,K
A 16------------BATTERY
A 17QAM1142-00116P CORD ASSYA,B,L
A 17QAM1145-00116P CORD ASSYC,D,E,F,G,H,I,J,K
A 18------------WARRANTY CARDBT-52008-1A,B,L
A 19------------WARRANTY CARDBT-51029-3A
A 19------------WARRANTY CARDBT-51018-5B
A 19------------WARRANTY CARDBT-51018-6L
A 20BT-51044-1REGIS. CARDA,B,L
A 21LVT1672-002AINST SHEET
A 22GET0222-001ATAG CAUTION SHL
KITSRW-MA372SCREW PARTS KITA9 A10 A11 A12 A13A
P 1GE33395-001ACARTONA
P 1GE33398-003ACARTONB
P 1GE33404-002ACARTONC
P 1GE33401-002ACARTOND,E,F,G
P 1GE33407-002ACARTONH,I,J,K
P 1GE33873-001ACARTONL
P 2QPC03004315PBPOLY BAG30cm x 43cm
P 3FSPG4002-001POLY BAGA,B,C,E,F,G,I,J,K,L
P 3FSPG4002-001POLY BAG(x2)D,H
P 5QPA00801205POLY BAG8cm x 12cm
P 6GE10247-001ACUSHION
P 7QPA01003003POLY BAG10cm x 30cmC,D,E,F,G,H,I,J,K
P 8QPC01002515POLY BAG10cm x 25cmC,D,E,F,G,H,I,J,K
P 9GE40276-003AAIR BUBBLE BAGA,B,L
3-17
Page 54
SCHEMATIC DIAGRAMS
CD RECEIVER
KD-A305J,KD-R300J,KD-R404UI
KD-R405U,KD-R405UN,KD-R405UT
KD-R405UH,KD-R406U,KD-R406UN
KD-R406UT,KD-R406UH, KD-S26J
DVD-ROM No.SML2009Q1
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
Contents
Block diagram
Standard schematic diagrams
Printed circuit boards
COPYRIGHT 2009 Victor Company of Japan, Limited.
KD-A305/KD-R300/KD-S26
2-1
2-2
2-8 to 10
No.MA429SCH<Rev.002>
2009/8
Page 55
Safety precaution
!
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
(Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade))
P1A
T1A
GEB10253A
C741
B320
B318
B317
B316
R354
R344
B742
B741
B740
Q341
B342
C701
B176
B175
B174
B925
B924
B922
B851
B918
B917
B540
B539
B538
B781
B164
B163
B909
Q921
Q922
R906
R905
R759
R757
R754
R749
R734
B311
CN901
B529
B527
B737
B1
B732
B804
B803
B716
GND
3.3V
RST
CL
DA
B713 B712
B802
B801
R739
B383
B382
VREF
B519
J801
X702
X701
X521
X1
S701
R977
R976
R972
R971
R903
R902
R901
R851
R819
R814
R812
R811
R810
R809
R808
R807
R804
R803
R802
R783
R782
R781
R779
R775
R774
R773
R772
R771
R770
R758
R756
R755
R753
R752
R751
R750
R748
R747
R746
R740
R738
R737
R736
R733
R731
R727
R726
R723
R721
R720
R719
R718
R717
R716
R715
R714
R713
R712
R711
R710
R709
R708
R707
R706
R704
R703
R702
R701
R594
R593
R592
R591
R588
R587
R586
R585
R584
R583
R566
R565
R559
R558
R556
R554
R549
R548
R547
R546
R545
R544
R543
R542
R541
R540
R538
R537
R536
R535
R529
R528
R527
R526
R525
R524
R522
R521
R520
R519
R518
R517
R516
R515
R514
R513
R512
R511
R510
R509
R508
R507
R506
R505
R504
R503
R502
R501
R500
R390
R389
R388
R387
R386
R385
R384
R383
R382
R381
R732
R353
R352
R343
R342
R305
R303
R175
R174
R165
R164
R163
R162
R161
R122
R92
R91
R82
R81
R17
R16
R11
R10
R7
R6
R5
R4
R3
R2
R1
Q977
Q976
Q785
Q784
Q782
Q781
Q521
Q501
R735
L901
L702
L701
L122
L121
L120
L9
L8
L7
L6
L5
L4
L3
L2
L1
J702
J321
J1
IC981
IC901
IC801
IC771
IC702
IC701
IC581
IC521
IC501
IC381
IC301
IC161
IC1
D972
D971
D901
D852
D851
D787
D786
D785
D784
D782
D781
D718
D717
D716
D715
D713
D712
D711
D709
D708
D707
D706
D702
D701
D501
D351
D341
D331
D2
D1
CN701
CN501
C985
C984
C983
C982
C971
C917
C916
C915
B921
C913
C912
C911
C909
C908
C907
C906
C905
C903
C902
C901
C852
C851
C801
C785
C784
C781
C771
C743
C742
C727
C726
B313
C722
C721
C720
C719
C718
C717
C715
C714
C712
C711
C710
C709
C708
C707
C706
C704
C703
C702
C592
C591
C590
C588
C587
C586
C585
C584
C583
C552
C551
C549
C548
C547
C546
C545
C544
C543
C542
C541
C540
C539
C538
C537
C536
C535
C534
C533
C532
C531
C530
C529
C528
C527
C526
C525
C524
C522
C521
C518
C517
C515
C513
C512
C511
C510
C509
C508
C507
C505
C504
C503
C502
C501
C393
C392
C390
C389
C388
C387
C386
C385
C384
C383
B381
C321
C320
C319
C318
C317
C316
C315
C314
C313
C312
C311
C304
C303
C302
C301
C181
C180
C175
C174
C173
C172
C171
C169
R166
C166
C165
C164
C163
C162
C161
C120
B2
C34
C32
C31
C27
C26
C25
C24
C23
C22
C19
C18
C17
C16
C15
C14
C13
C12
C11
C10
C9
C8
C7
C6
C5
C4
C3
C2
C1
B902
B901
B106
B105
ARF
Old Main board
Old LED board
F1A S1A
D604
P1A
GEA10254A2
T1A
GEB10254A2
PbF
MARK
UL
forward sidereverse side
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
(Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade))
forward side
reverse side
T2A
GEB10253A
C904
R776
R784
C182
C192
C193
C183
C741
B320
B318
B317
B316
R354
R344
B741
B740
Q341
B342
C701
B176
B175
B174
B925
B924
B922
B851
B918
B917
B540
B539
B538
B781
B164
B163
B909
Q921
Q922
R906
R905
R759
R757
R754
R749
R734
B311
CN901
B529
B527
B737
B1
B732
B804
B803
B716
GND
3.3V
RST
CL
DA
B713 B712
B802
B801
R739
B383
B382
VREF
B519
J801
X702
X701
X521
X1
S701
R977
R976
R972
R971
R903
R902
R901
R851
R819
R814
R812
R811
R810
R809
R808
R807
R804
R803
R802
R783
R782
R781
R779
R775
R774
R773
R772
R771
R770
R758
R756
R755
R753
R752
R751
R750
R748
R747
R746
R740
R738
R737
R736
R733
R731
R727
R726
R723
R721
R720
R719
R718
R717
R716
R715
R714
R713
R712
R711
R710
R709
R708
R707
R706
R704
R703
R702
R701
R594
R593
R592
R591
R588
R587
R586
R585
R584
R583
R566
R565
R559
R558
R556
R554
R549
R548
R547
R546
R545
R544
R543
R542
R541
R540
R538
R537
R536
R535
R529
R528
R527
R526
R525
R524
R522
R521
R520
R519
R518
R517
R516
R515
R514
R513
R512
R511
R510
R509
R508
R507
R506
R505
R504
R503
R502
R501
R500
R390
R389
R388
R387
R386
R385
R384
R383
R382
R381
R732
R353
R352
R343
R342
R305
R303
R175
R174
R165
R164
R163
R162
R161
R122
R92
R91
R82
R81
R17
R16
R11
R10
R7
R6
R5
R4
R3
R2
R1
Q977
Q976
Q785
Q784
Q782
Q781
Q521
Q501
R735
L901
L702
L701
L122
L121
L120
L9
L8
L7
L6
L5
L4
L3
L2
L1
J702
J321
J1
IC981
IC901
IC801
IC771
IC702
IC701
IC581
IC521
IC501
IC381
IC301
IC161
IC1
D972
D971
D901
D852
D851
D787
D786
D785
D784
D782
D781
D718
D717
D716
D715
D713
D712
D711
D709
D708
D707
D706
D702
D701
D501
D351
D341
D331
D2
D1
CN701
CN501
C985
C984
C983
C982
C971
C917
C916
C915
B921
C913
C912
C911
C909
C908
C907
C906
C905
C903
C902
C901
C852
C851
C801
C785
C784
C781
C771
C743
C742
C727
C726
B313
C722
C721
C720
C719
C718
C717
C715
C714
C712
C711
C710
C709
C708
C707
C706
C704
C703
C702
C592
C591
C590
C588
C587
C586
C585
C584
C583
C552
C551
C549
C548
C547
C546
C545
C544
C543
C542
C541
C540
C539
C538
C537
C536
C535
C534
C533
C532
C531
C530
C529
C528
C527
C526
C525
C524
C522
C521
C518
C517
C515
C513
C512
C511
C510
C509
C508
C507
C505
C504
C503
C502
C501
C393
C392
C390
C389
C388
C387
C386
C385
C384
C383
B381
C321
C320
C319
C318
C317
C316
C315
C314
C313
C312
C311
C304
C303
C302
C301
C181
C180
C175
C174
C173
C172
C171
C169
R166
C166
C165
C164
C163
C162
C161
C120
B2
C34
C32
C31
C27
C26
C25
C24
C23
C22
C19
C18
C17
C16
C15
C14
C13
C12
C11
C10
C9
C8
C7
C6
C5
C4
C3
C2
C1
B902
B901
B106
B105
ARF
S1A
D604
GEA10254A2
T1A
GEB10254A2
PbF
MARK
UL
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
(Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade))
Main board
LED board
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
(Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade))
Page 64
Old Switch board
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
(Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade))
D630
S601
R605
R604
C603
D606
S605
S604
D605
R603
R602
S603
forward side
S606
S609
S602
R608
R609
S607
LCD1
GEA10254-
JS686
S608
R610
D602
R611
IC681
D601
reverse side
GEB10254A1
T1A
P1A
J601
R666
R665
R671
C685
R670
C684
R661
C686
R662
D661
R660
C663
C665
C666
R663
IC661
R664
C662
C661
B607
R667
C608
C609
R615
R614
R618
C607
C606
Q604
Q608
C610
C604
Q607
B606
R636
B605
Q605
Q610
R638
R637
IC601
R649
C651
R646
D650
R651
C650
Q601
C652
R656
R647
R644
B602
R658
R648
Q611
B604
JS686
C602
R645
R657
R682
R683
IC681
R681
C682
Switch board
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
(Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade))
S610
D632
S611
R634
D631
R613
R612
R607
S1A
A1
B601
D668
D660
D664
D666
D659
C601
B603
CJ601
Q602
F1A
R632
R631
J601
R630
PbF
MARK
UL
R601
D630
R605
R604
S604
R603
R602
GEB10254A1
J601
S601
C603
D606
S605
D605
S603
forward side
S606
S609
S602
R608
R609
S607
JS
68
S608
R610
R611
6
D602
IC681
LCD1
GEA10254-
D601
A1
S610
D632
S611
R634
D631
R613
R612
R607
S1A
Q602
R632
R631
J601
reverse side
C608
C609
Q610
R638
T1A
R671
C685
R670
C684
R661
C686
R662
D661
R660
C663
C665
C666
R663
R666
R665
IC661
R664
C662
C661
B607
R667
R614
R637
IC601
R615
R618
C607
C606
Q604
Q608
C610
C604
Q607
B606
R636
B605
Q605
R649
C651
R646
D650
R651
C650
Q601
C652
R656
R647
R644
B602
R658
R648
Q611
B604
686
JS
C602
R645
R657
R682
R683
IC681
R681
C682
B601
D668
D660
D664
D666
D659
C601
B603
CJ601
R630
PbF
MARK
UL
R601
2-9
Page 65
Mecha board
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
(Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade))
(Photo board)
SW1
Q301
LVA10771-A2
(Mecha board)
P1A
T1A
MARK
UL
PbF
P1A
LO
R101
D101
SW2
T1A
BROWN
Q302
WHITE
RED
ORANGE
BROWN
UL
MARK
PbF
LVA10771-
CN101
CN102
RED
BLACK
R202
R203
R102
R103
YELLOW
Q201
FE
WHITE
REST
ORANGE
Q101
SW1
SW2
SP
B101
R105
R205
R204
R104
ORANGE
BROWN
SW2
RED
SW1
D201
R201
A1
Reset board
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
(Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade))
LVA10771-A3
PbF
MARK
UL
SW1
2-10
Page 66
< MEMO >
Page 67
Victor Company of Japan, Limited
Mobile Entertainment Division 10-1,1chome,Ohwatari-machi,Maebashi-city,Gumma-ken,371-8543,Japan
(No.MA429SCH<Rev.002>)
Printed in Japan
VSE
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.