JVC KD-R322, KD-R321 Instruction Manual

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Vous avez des PROBLÈMES de fonctionnement?

Réinitialisez votre appareil

Référez-vous à la page intitulée Comment réinitialiser votre appareil

ENGLISH

FRANÇAIS

KD-R322/KD-R321

CD RECEIVER / RÉCEPTEUR CD

Dear Customer,
This apparatus is in conformance with the valid
European directives and standards regarding
electromagnetic compatibility and electrical safety.

European representative of Victor Company of
Japan, Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany

EN, FR

Cher(e) client(e),
Cet appareil est conforme aux directives et
normes européennes en vigueur concernant la
compatibilité électromagnétique et à la sécurité
électrique.

Représentant européen de la société Victor
Company of Japan, Limited:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Allemagne

0910DTSMDTJEIN© 2010 Victor Company of Japan, Limited

For canceling the display demonstration, see page 4. / Pour annuler la démonstration des
affichages, référez-vous à la page 4.

For installation and connections, refer to the separate manual.
Pour l’installation et les raccordements, se référer au manuel séparé.

INSTRUCTIONS

MANUEL D’INSTRUCTIONS

GET0678-003A

[E/EU]

CoverRear_KD-R322_R321[E]_3.indd 1-2 8/3/10 10:49:25 AM

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and

to obtain the best possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave
all servicing to qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with
optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

WARNING:

Stop the car before operating the unit.

Battery

Products

Information for Users on Disposal of
Old Equipment and Batteries

[European Union only]

These symbols indicate that the product and
the battery with this symbol should not be
disposed as general household waste at its
end-of-life.
If you wish to dispose of this product and
the battery, please do so in accordance with
applicable national legislation or other rules
in your country and municipality.
By disposing of this product correctly, you
will help to conserve natural resources and
will help prevent potential negative effects
on the environment and human health.

Notice:

The sign Pb below the symbol for batteries
indicates that this battery contains lead.

2 ENGLISH

Caution:

Adjust the volume so that you can hear sounds
outside the car. Driving with the volume too
high may cause an accident.

Caution on volume setting:

Discs produce very little noise compared
with other sources. Lower the volume before
playing a disc to avoid damaging the speakers
by the sudden increase of the output level.

Caution for DualDisc playback:

The Non-DVD side of a “DualDisc” does not
comply with the “Compact Disc Digital Audio”
standard. Therefore, the use of Non-DVD side
of a DualDisc on this product may not be
recommended.

EN02-15_KD-R322_R321[E]_f.indd 2 9/8/10 11:27:55 AM

How to attach/detach the control
panel

How to reset your unit

Your preset adjustments will
also be erased.

How to forcibly eject a disc

[Hold]

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

Condensation : When the car is air­conditioned, moisture may collect on the
laser lens. This may cause disc read errors. In
this case, remove the disc and wait for the
moisture to evaporate.
Temperature inside the car : If you have
parked the car for a long time in hot or cold
weather, wait until the temperature in the car
becomes normal before operating the unit.

CONTENTS

3 How to attach/detach the control

panel

3 How to reset your unit
3 How to forcibly eject a disc

3 About discs

4 Canceling the display

demonstration

4 Setting the clock

5 Basic operations

6 Listening to the radio

8 Listening to a disc

9 Connecting the other external

components

9 Listening to the other external

components

10 Selecting a preset sound mode

10 Menu operations

13 Troubleshooting

14 Using Bluetooth ® devices

15 Specifications

15 Maintenance

About discs

This unit can only play the CDs with:

Discs that cannot be used:

• Discs that are not round.

• Discs with coloring on the recording surface
or discs that are dirty.

• You cannot play a Recordable/ReWritable
disc that has not been finalized. (For the
finalization process refer to your disc writing
software, and your disc recorder instruction
manual.)

• 3-inch CD cannot be used. Attempt to insert
using an adapter can cause malfunction.

EN02-15_KD-R322_R321[E]_f.indd 3 9/8/10 11:27:56 AM

Handling discs:

• Do not touch the recording surface of the
disc.

• Do not stick tape etc. on the disc, or use a disc
with tape stuck on it.

• Do not use any accessories for the disc.

• Clean from the center of the disc and move
outward.

• Clean the disc with a dry silicon or soft cloth.
Do not use any solvents.

• When removing discs from this unit, pull them
out horizontally.

• Remove the rims from the center hole and
disc edge before inserting a disc.

3ENGLISH

Canceling the display demonstration

Display demonstration will be activated automatically if no operation is done for about 20 seconds.

1 Turn on the power.

4 Select <DEMO OFF>.

2

[Hold]

(Initial setting)

3

(Initial setting)

Setting the clock

1 Turn on the power.

2

3 Select <CLOCK>.

4 Select <CLOCK SET>.

5 Adjust the hour.

[Hold]

(Initial setting)

5

6 Finish the procedure.

6 Adjust the minute.

7 Select <24H/12H>.

8 Select <24 HOUR> or

<12 HOUR>.

9 Finish the procedure.

(Initial setting)

4 ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 4 9/8/10 11:27:56 AM

Basic operations

Loading slot Display window

When you press or hold the following button(s)...

Button General operation

• Turns on.

/ SOURCE

Control dial

(turn)

Control dial

(press)

EQ

Number

buttons (1 – 6)

BRIGHTNESS Enters <BRIGHTNESS> menu directly. (page 11)

T/P BACK

DISP

• Turns off [Hold].

• Selects the sources (FM, CD, F-AUX, BT AUDIO or R-AUX or BT PHONE, AM). “CD”
is selectable only when a disc is loaded.

• Adjusts the volume level.

• Selects items.

• Mutes the sound while listening to a source. If the source is “CD,” playback
pauses. Press the control dial again to cancel muting or resume playback.

• Confirms selection.

• Selects the sound mode.

• Enters tone level adjustment directly [Hold]. (page 10)

• Selects preset stations.

• Stores the current station into the selected number button [Hold].

• Press number button 1 (RPT) or 2 (RND) to enter REPEAT/RANDOM setting
directly. (page 8)

• Activates/deactivates TA Standby Reception.

• Enters PTY Searching mode [Hold].

• Returns to the previous menu.

• Exit from the menu [Hold].

• Changes the display information.

• Scrolls the display information [Hold].

Control dial Ejects the disc

Front auxiliary input jackDetaches the panel

5ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 5 9/8/10 11:27:57 AM

Listening to the radio

~

]

“FM” or “AM”

“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.

Ÿ

Improving the FM reception

1

[Hold]

2

]

<TUNER> ] <MONO> ] <MONO ON>
Reception improves, but stereo effect
will be lost.

To restore the stereo effect, repeat the same
procedure to select <MONO OFF>.

Automatic presetting (FM)—

SSM (Strong-station Sequential Memory)

You can preset up to 18 stations for FM.

While listening to a station...

1

[Hold]

2

• Auto search [Press].

• Manual search [Hold].
“M” flashes, then press the button

repeatedly.

Manual presetting (FM/AM)

You can preset up to 18 stations for FM and 6
stations for AM.

1

]

Tune in to a station you want to

preset.

2

“PRESET MODE” flashes.

[Hold]

3

]

Selects preset number.
Preset number flashes and “MEMORY”
appears.

• Pressing and holding the number buttons
(1 – 6) can also store the current station to the
selected number buttons (1 – 6).

Selecting a preset station

]

<TUNER> ] <SSM> ]
<SSM 01 – 06 / 07 – 12 / 13 – 18>
“SSM” flashes and local stations with the
strongest signal are searched and stored
automatically.

To preset another 6 stations, repeat the
above procedure by selecting one of the other
6 SSM setting ranges.

Changing the display information (for non­Radio Data System station)

Frequency j Clock

6 ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 6 9/8/10 11:27:57 AM

• Pressing the number buttons (1 – 6) can also
select the preset stations (1 – 6).

1

or

2

The following features are available
only for FM Radio Data System stations.

Searching for your favourite
FM Radio Data System
programme—

You can tune in to a station broadcasting your
favourite programme by searching for a PTY
code.

1

The last selected PTY code appears.

PTY Search

[Hold]

2

]

Select one of your favourite
programme types or a PTY code, and
start searching.

If there is a station broadcasting a
programme of the same PTY code as you
have selected, that station is tuned in.

PTY codes: NEWS, AFFAIRS, INFO, SPORT,
EDUCATE, DRAMA, CULTURE, SCIENCE,
VARIED, POP M (music), ROCK M (music),
EASY M (music), LIGHT M (music), CLASSICS,
OTHER M (music), WEATHER, FINANCE,
CHILDREN, SOCIAL, RELIGION, PHONE IN,
TRAVEL, LEISURE, JAZZ, COUNTRY,
NATION M (music), OLDIES, FOLK M (music),
DOCUMENT

TA Standby Reception

TA Standby Reception allows the unit to switch
temporarily to Traffic Announcement (TA) from
any source other than AM.

To activate TA Standby Reception

If the TP indicator lights up, TA
Standby Reception is activated.
If the TP indicator flashes, TA
Standby Reception is not yet
activated.

• To activate the reception, tune in to another
station providing Radio Data System signals
required for TA Standby Reception.

• To deactivate the reception, press
again.

T/P BACK

NEWS Standby Reception

NEWS Standby Reception allows the unit to
switch temporarily to your NEWS programme
from any source other than AM.

To activate NEWS Standby Reception, see
<NEWS-STBY>. (page 12)

Tracing the same programme—

Network-Tracking Reception

When driving in an area where FM reception is
not sufficient enough, this unit automatically
tunes in to another FM Radio Data System
station of the same network, possibly
broadcasting the same programme with
stronger signals.

To change the Network-Tracking Reception
setting, see <AF-REG>. (page 12)

Automatic station selection—

Programme Search

Usually when you select a preset number, the
station preset in that number is tuned in.
If the signals from the FM Radio Data System
preset station are not sufficient for good
reception, this unit, using the AF data, tunes in
to another frequency possibly broadcasting the
same programme as the original preset station
is broadcasting.

To activate Programme Search, see
<P-SEARCH>. (page 12)

Changing the display information

Station name (PS) = Station
Frequency = Programme type
(PTY) = Clock = (back to the
beginning)

7ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 7 9/8/10 11:27:57 AM

Listening to a disc

~

]

“CD”

Ÿ

All tracks will be played repeatedly until you change the source
or eject the disc.

Stopping playback and ejecting
the disc

If the ejected disc is not
removed within 15 seconds, it is
automatically inserted into the
loading slot.

Selecting a track/folder

Selects folder of the MP3/WMA

[Press] Selects track.
[Hold] Fast-forwards or
reverses the track.

Changing the display information

Disc title/Album name/performer (folder
name)* = Track title (file name)* = Current
track number with the elapsed playing time =
Current track number with the clock time =
(back to the beginning)

* “NO NAME” appears for conventional CDs or if

not recorded.

8 ENGLISH

Playback starts
automatically.

Selecting a track/folder from the
list

• If the MP3/WMA disc contains many tracks,
you can fast search (±10, ±100) through the
disc by turning the control dial quickly.

•

To return to the previous menu, press
T/P BACK.

Selecting the playback modes

You can use only one of the following playback
modes at a time.

1

• Pressing number button 1 (RPT) or

[Hold]

2 (RND) can enter REPEAT/RANDOM
setting directly. Then, perform step 3.

2

]

“REPEAT” j “RANDOM”

3

REPEAT
TRACK RPT : Repeats current track
FOLDER RPT : Repeats current folder

RANDOM
FOLDER RND : Randomly plays all tracks

ALL RND : Randomly plays all tracks

To cancel repeat play or random play, select
“RPT OFF” or “RND OFF.”

of current folder, then
tracks of next folders

EN02-15_KD-R322_R321[E]_f.indd 8 9/8/10 11:27:57 AM

Connecting the other external components

You can connect an external component to the auxiliary input jack on the control panel (F-AUX)
and/or on the rear side of the unit (R-AUX).

Summary of using the external components through the auxiliary input jacks:

item

Preparation

Sub­item

Setting

Source

name

BT PHONE *

External component

Portable audio
player

Bluetooth device Rear SRC SELECT R-AUX BT ADAPTER BT AUDIO/

* ”BT PHONE” appears when a Bluetooth phone is in use.

Auxiliary

input jack

Front SRC SELECT F-AUX ON F-AUX
Rear SRC SELECT R-AUX ON R-AUX

Menu setting

On the control panel (F-AUX): On the rear panel (R-AUX):

3.5 mm stereo mini

3.5 mm stereo mini
plug (not supplied)

plug (with “L” shaped
connector) (not supplied)

Connecting

cable/device

(not supplied)

See below.

KS-BTA100
(page 14)

Portable audio player,

etc.

Recommended to use a 3-terminal plug head stereo mini plug for
optimum audio output.

Portable audio player,

etc.

Listening to the other external components

For details, refer also to the instructions supplied with the external components.

~

]

“F-AUX” or “R-AUX”

EN02-15_KD-R322_R321[E]_f.indd 9 9/8/10 11:27:57 AM

Turn on the connected component and

Ÿ

start playing the source.

9ENGLISH

Selecting a preset sound mode

You can select a preset sound mode suitable
for the music genre.

While listening, you can adjust the subwoofer
level and tone level of the selected sound mode.

1

FLAT = NATURAL =
DYNAMIC
BASS BOOST

to the beginning)

=

VOCAL BOOST =

[Hold]

=

USER = (back

2

Adjust the level:
SUB.W *: 00 to 08
BASS/ MID/ TRE: –06 to +06
The sound mode is automatically stored
and changed to “USER.”

* Subwoofer level is adjustable only when <L/O

MODE> is set to <SUB.W>. (page 11)

Storing your own sound mode

You can store your own adjustments in
memory.

1

[Hold]

Menu operations

2

]

<PRO EQ> ] <BASS/ MIDDLE/

TREBLE>

3

Adjust the sound elements of the
selected tone.

BASS [Initial: 80 Hz, 00, Q1.0]
Frequency: 60/ 80/ 100/ 200 Hz
Level: –06 to +06
Q: Q1.0/ 1.25/ 1.5/ 2.0
MIDDLE [Initial: 1.0 kHz, 00, Q1.25]
Frequency: 0.5/ 1.0/ 1.5/ 2.5 kHz
Level: –06 to +06
Q: Q0.75/ 1.0/ 1.25
TREBLE [Initial: 10.0 kHz, 00, Q FIX]
Frequency: 10.0/ 12.5/ 15.0/ 17.5 kHz
Level: –06 to +06
Q: Q FIX

Repeat steps 2 and 3 to adjust other

4

tones.
The adjustments made is automatically
stored and changed to “USER.”

1

If no operation is done
for about 60 seconds, the
operation will be canceled.

Menu item

DEMO

CLOCK

*1 Takes effect only when CT (clock time) data is received.

10 ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 10 9/8/10 11:27:58 AM

[Hold]

For settings, see page 4.

CLOCK SET

24H/12H
CLOCK ADJ *1AUTO

For settings, see page 4.

For settings, see page 4.

Radio Data System signal. /

2 3

Selectable setting, [Initial: Underlined]

: The built-in clock is automatically adjusted using the CT (clock time) data in the

OFF

: Cancels.

Repeat step 2 if necessary.

• To return to the previous
menu, press T/P BACK.

• To exit from the menu, press
DISP or MENU.

Menu item

DIMMER SET AUTO

DIMMER

BRIGHTNESS DAY [ 25

: Dims the display to the previous setting when you turn on the car headlights. *2 /

ON

: Dims the display and button illumination (50% of the selected brightness level). /

OFF

: Cancels (100% of the selected brightness level).

Selectable setting, [Initial: Underlined]

] /

NIGHT [ 11

] : Selects the display and button illumination brightness level

[00 — 31] for day and night.

3

SCROLL *

DISPLAY

TAG DISPLAY ON

PRO EQ

FADER *4, *5R06 — F06

BALANCE *5L06 — R06

LOUD ON

VOL ADJUST –05 — +05

ONCE

: Scrolls the displayed information once. /

intervals). /

OFF

: Cancels.

(Pressing

DISP

for more than one second can scroll the display regardless of the setting.)

: Shows the Tag information while playing MP3/WMA tracks. /

AUTO

: Repeats scrolling (at 5-second

OFF

See page 10.

[ 00 ] : Adjusts the front and rear speaker output balance.

[ 00 ] : Adjusts the left and right speaker output balance.

: Boost low and high frequencies to produce a well-balanced sound at a low volume

level. /

OFF

: Cancels.

[ 00 ] : Presets the volume adjustment level of each source (except

: Cancels.

“FM”), compared to the FM volume level. The volume level will automatically increase or
decrease when you change the source. Before adjustment, select the source you want to
adjust. (“VOL ADJ FIX” appears on the display if “FM” is selected as the source.)

L/O MODE SUB.W

AUDIO

SUB.W LPF *6LOW 55Hz / LOW 85Hz / LOW 120Hz

: Selects if the REAR/SW terminals are used for connecting a subwoofer (through

an external amplifier). /

REAR

: Selects if the REAR/SW terminals are used for connecting

the speakers (through an external amplifier).

: Frequencies lower than

55 Hz/85 Hz/120 Hz are sent to the subwoofer.

SUB.W LEVEL

HPF ON

BEEP ON / OFF

TEL MUTING *7ON

*600 — 08

[ 04 ] : Adjusts the subwoofer output level.

: Activates the High Pass Filter. The unit selects the cutoff frequency to the rear

speakers. /

OFF

: Deactivates (all signals are sent to the rear speakers).

: Activates or deactivates the keypress tone.

: Mutes the sounds while using the cellular phone (not connected through

KS-BTA100). /

OFF

: Cancels.

*2 The illumination control lead connection is required. (See “Installation/Connection Manual.”) This setting may not work

correctly on some vehicles (particularly on those having a control dial for dimming). In this case, change the setting to
any other than <DIMMER AUTO>.

*3 Some characters or symbols will not be shown correctly (or will be blanked) on the display.
*4 If you are using a two-speaker system, set the fader level to “00.”
*5 This adjustment will not affect the subwoofer output.
*6 Displayed only when <L/O MODE> is set to <SUB.W>.
*7 This setting does not work if <BT ADAPTER> is selected for <R-AUX> of the <SRC SELECT>.

Continued...

11ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 11 9/8/10 11:27:58 AM

Menu item

AMP GAIN *8LOW POWER

Selectable setting, [Initial: Underlined]

: VOLUME 00 – VOLUME 30 (Selects if the maximum power

of each speaker is less than 50 W to prevent damaging the speakers.) /

AUDIO

SSM *
AF-REG *

9

10

HIGH POWER

: VOLUME 00 – VOLUME 50

See page 6.

AF ON

: When the currently received signals become weak, the unit switches to another
station (the programme may differ from the one currently received). (The AF indicator
lights up.) /

AF-REG ON

: When the currently received signals become weak, the
unit switches to another station broadcasting the same programme. (The AF and REG
indicators light up.) /

NEWS-

9, *10

STBY

*

TUNER

P-SEARCH *10SEARCH ON / SEARCH OFF

NEWS ON / NEWS OFF

OFF

: Cancels.

: Activates or deactivates NEWS Standby Reception.

: Activates Programme Search (if AF-REG is turn on) or

deactivates.

9

MONO *
IF BAND AUTO

See page 6.

: Increases the tuner selectivity to reduce interference noises between adjacent

stations. (Stereo effect may be lost.) /

WIDE

: Subject to interference noises from

adjacent stations, but sound quality will not be degraded and the stereo effect will remain.

11

AM *
F-AUX *
R-AUX *

SRC SELECT

ON / OFF

11

11

: Enable or disable “AM” in source selection.

ON / OFF

: Enable or disable “F-AUX” in source selection.

ON / OFF

: Enable or disable “R-AUX” in source selection. /

if the rear auxiliary input jack is connected to the Bluetooth adapter, KS-BTA100. (page 9)

BT ADAPTER *12

*8 The volume level automatically changes to “VOLUME 30” if you change to <LOW POWER> with the volume level set

higher than “VOLUME 30.”

9

*

Displayed only when the source is “FM.”

10

*

Only for FM Radio Data System stations.

11

*

Displayed only when any source other than “AM/ F-AUX/ R-AUX/ BT AUDIO” is selected separately.

12

*

When <BT ADAPTER> is selected, source name is changed to “BT AUDIO” from “R-AUX.”

: Selects

Additional information

• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.

• This unit can play back files with the extension code
<.mp3> or <.wma> (regardless of the letter
case—upper/lower).

• This unit can play back the files meeting the conditions
below:

– Bit rate: MP3/WMA: 8 kbps — 320 kbps
– Sampling frequency:
MP3: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz,

16 kHz, 12 kHz, 11.025 kHz, 8 kHz

WMA: 48 kHz, 44.1 kHz, 32 kHz, 22.05 kHz

• This unit can show WMA Tag and ID3 Tag Version

1.0/1.1/2.2/2.3/2.4 (for MP3).

• The search function works but search speed is not
constant.

12 ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 12 9/8/10 11:27:58 AM

• The maximum number of characters for file/folder
names vary depending on the disc format used (includes
4 extension characters—<.mp3> or <.wma>).

ISO 9660 Level 1 and 2, Romeo: 64 characters, Joliet: 32

characters, Windows long file name: 64 characters

• This unit can play back files recorded in VBR (variable
bit rate). (Files recorded in VBR have a discrepancy in
elapsed time indication.)

• This unit cannot play back the following files:

– MP3 files: encoded in MP3i and MP3 PRO format; an

inappropriate format; layer 1/2.

– WMA files: encoded in lossless, professional, and

voice format; not based upon Windows Media®
Audio; copy-protected with DRM.

– Files which have data such as AIFF, ATRAC3, etc.

Troubleshooting

Symptom Remedy/Cause

Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.

• Make sure the unit is not muted/paused. (page 5)

• Check the cords and connections.

“MISWIRING CHK WIRING THEN RESET
UNIT” appears on the display and no
operations can be done.

General

The unit does not work at all. Reset the unit. (page 3)

“F-AUX” or “R-AUX” cannot be selected. Check the <SRC SELECT>

Sound is sometimes interrupted while
listening to an external component
connected to the auxiliary input jack.

SSM automatic presetting does not work. Store stations manually.

Static noise while listening to the radio. Connect the aerial firmly.

FM/AM

“AM” cannot be selected. Check the <SRC SELECT>

Disc cannot be played back. Insert the disc correctly.

CD-R/CD-RW cannot be played back and
track cannot be skipped.

Disc sound is sometimes interrupted. Stop playback while driving on rough roads. / Change the

“NO DISC” appears on the display. Insert a playable disc into the loading slot.

“PLEASE” and “EJECT“ appear alternately

Disc playback

on the display.

“IN DISC” appears on the display. The disc cannot be ejected properly. Make sure nothing is

Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in a format

Noise is generated. Skip to another track or change the disc.

“READING” keeps flashing on the display. A longer readout time is required. Do not use too many

Tracks do not play back in the order you
have intended them to play.

MP3/WMA playback

The elapsed playing time is not correct. This sometimes occurs during playback. This is caused by how

The correct characters are not displayed
(e.g. album name).

Check to be sure the terminals of the speaker leads are covered
with insulating tape properly, then reset the unit. (page 3)
If the message does not disappear, consult your JVC IN-CAR
ENTERTAINMENT dealer or a company supplying kits.

=

<F-AUX / R-AUX> setting.

(page 12)

Check to be sure the recommended stereo mini plug is used for
connection. (page 9)

=

<AM> setting. (page 12)

Insert a finalized CD-R/CD-RW (finalize with the component
which you used for recording).

disc. / Check the cords and connections.

0

, then insert a disc correctly.

Press

blocking the loading slot.

compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.

• Add the extension code <.mp3> or <.wma> to the file
names.

hierarchical levels and folders.

The playback order is determined when the files are recorded.

the tracks are recorded on the disc.

This unit can only display letters (upper case), numbers, and a
limited number of symbols.

13ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 13 9/8/10 11:27:58 AM

Using Bluetooth ® devices

For Bluetooth operations, it is required to connect the Bluetooth adapter, KS-BTA100 (not supplied)
to the auxiliary input jack (R-AUX/BT ADAPTER) on the rear of the unit. (page 9)

• For details, refer also to the instructions supplied with the Bluetooth adapter and the Bluetooth
device.

• Operations may be different according to the connected device.

Preparation

1 Register (pair) a Bluetooth device with KS-BTA100.

Refer to the instructions manual supplied with KS-BTA100.

2 Change the <SRC SELECT> settings of this unit.

]

[Hold]

Using the Bluetooth mobile phone

Adjusting the microphone volume

(Low) (High)

KS-BTA100

Microphone

Volume level: High/ Normal (initial)/ Low

• Receiving a call
When a call comes in...

• Making a call
Making a call to the last connected number from

your phone.

• Switching between handsfree and phone
While talking...

• Ends/rejects call

• Voice dialing

[Hold]

Voice dialing is available only when the connected

mobile phone has the voice recognition system.

<SRC SELECT> ] <R-AUX> ]

<BT ADAPTER>

Using the Bluetooth audio device

1

(CD receiver)

If playback does not start, operate the Bluetooth audio player to start playback.

About microphone volume:

• When you turn off the power of the CD receiver, the volume level changes to Normal.

14 ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 14 9/21/10 3:56:22 PM

]

“BT AUDIO”

[Press] Selects track.
[Hold] Fast-forwards or reverses the track.

2

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output :

Front/Rear :

Continuous Power Output (RMS) :

Front/Rear :

40 Hz to 20 000 Hz at no more than 1% total
harmonic distortion.

Load Impedance :
Frequency Response :
Signal-to-Noise Ratio :
Line-Out or Subwoofer-Out Level/

Impedance :

Output Impedance :

50 W per channel

20 W per channel into 4 Ω,

2.5 V/20 kΩ load (full scale)

4 Ω (4 Ω to 8 Ω allowance)

40 Hz to 20 000 Hz

70 dB

1 kΩ

TUNER SECTION

Frequency Range :

FM :

87.5 MHz to 108.0 MHz

AM :

MW : 531 kHz to 1 611 kHz

LW : 153 kHz to 279 kHz

FM Tuner :

Usable Sensitivity :
50 dB Quieting Sensitivity :

(1.8 μV/75 Ω)

Alternate Channel Selectivity (400 kHz) :

65 dB

Frequency Response :
Stereo Separation:

MW Tuner :

Sensitivity/Selectivity :

LW Tuner :

Sensitivity :

9.3 dBf (0.8 μV/75 Ω)

16.3 dBf

40 Hz to 15 000 Hz

40 dB

20 μV/40 dB

50 μV

CD PLAYER SECTION

Type :

Compact disc player

Signal Detection System :

pickup (semiconductor laser)

Number of Channels :
Frequency Response :
Signal-to-Noise Ratio :
Wow and Flutter :
MP3 Decoding Format (MPEG1/2 Audio

Layer 3) :

Max. Bit Rate: 320 kbps

WMA (Windows Media® Audio) Decoding

Format :

Max. Bit Rate: 192 kbps

2 channels (stereo)

5 Hz to 20 000 Hz

98 dB

Less than measurable limit

GENERAL

Power Requirement :

DC 14.4 V (11 V to 16 V allowance)

Grounding System :
Allowable Operating Temperature :

0°C to +40°C

Dimensions (W × H × D) : (approx.)

– Installation Size :
182 mm × 52 mm × 159 mm
– Panel Size :
188 mm × 59 mm × 9 mm

Mass :

1.2 kg (excluding accessories)

Subject to change without notice.

Microsoft and Windows Media are either
registered trademarks or trademarks of
Microsoft Corporation in the United States
and/or other countries.

Operating Voltage :

Negative ground

Non-contact optical

Maintenance

Cleaning the unit

Wipe off the dirt on the panel with a dry silicon or soft cloth. Failure to observe this precaution
may result in damage to the monitor or unit.

Cleaning the connector

Wipe off dirt on the connector of the unit and panel. Use a cotton swab or cloth.

15ENGLISH

EN02-15_KD-R322_R321[E]_f.indd 15 9/8/10 11:27:59 AM

Merci pour avoir acheté un produit JVC.

Veuillez lire attentivement toutes les instructions avant d’utiliser l’appareil afin de bien comprendre

son fonctionnement et d’obtenir les meilleures performances possibles.

IMPORTANT POUR PRODUITS LASER

1. PRODUIT LASER CLASSE 1

2. ATTENTION: N’ouvrez pas le couvercle supérieur. Il n’y a aucune pièce réparable par l’utilisateur

à l’intérieur de l’appareil; confiez toute réparation à un personnel qualifié.

3. ATTENTION: Rayonnement laser visible et/ou invisible de classe 1M une fois ouvert. Ne pas

regarder directement avec des instruments optiques.

4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À L’EXTÉRIEUR DE

L’APPAREIL.

AVERTISSEMENT:

Arrêtez la voiture avant de manipuler l’appareil.

Pile

Produits

Informations relatives à l’élimination
des appareils et des piles usagés, à
l’intention des utilisateurs

[Union européenne seulement]

Ces symboles signifient que le produit et les
piles ne doivent pas être éliminés en tant
que déchet ménager à la fin de son cycle
de vie.
Si vous souhaitez éliminer ce produit et les
piles, faites-le conformément à la législation
nationale ou autres règles en vigueur dans
votre pays et votre municipalité.
En éliminant correctement ce produit, vous
contribuez à la conservation des ressources
naturelles et à la prévention des éventuels
effets négatifs sur l’environnement et la
santé humaine.

Notification:

La marque Pb en dessous du symbole des
piles indique que cette pile contient du
plomb.

2

FRANÇAIS

Attention:

Ajustez le volume de façon à pouvoir entendre
les sons extérieurs à la voiture. Conduire avec
le volume trop haut peut être la cause d’un
accident.

Précautions sur le réglage du volume:

Les disques produisent très peut de bruit par
rapport aux autres sources. Réduisez le volume
avant de reproduire un disque afin d’éviter
d’endommager les enceintes par la soudaine
augmentation du niveau de sortie.

Précautions pour la lecture de disques à
double face:

La face non DVD d’un disque à “DualDisc” n’est
pas compatible avec le standard “Compact Disc
Digital Audio”. Par conséquent, l’utilisation de la
face non DVD d’un disque à double face sur cet
appareil n’est pas recommandée.

FR02-15_KD-R322_R321[E_EU]f.indd 2 8/30/10 11:34:06 AM

Comment attacher/détacher le
panneau de commande

TABLE DES MATIERES

3 Comment attacher/détacher le

3 Comment réinitialiser votre appareil
3 Comment forcer l’éjection d’un

3 À propos des disques

Comment réinitialiser votre appareil

Vos ajustements préréglés
sont aussi effacés.

4 Annulation des démonstrations

4 Réglage de l’horloge
5 Opérations de base
6 Écoute de la radio

Comment forcer l’éjection d’un
disque

• Faites attention de ne pas faire tomber le
disque quand il est éjecté.

• Si cela ne fonctionne pas, essayez de
réinitialiser l’autoradio.

Condensation : Quand une voiture est climatisée,
de la condensation peut se produire sur la lentille
du laser. Cela peut être la cause d’une erreur de
lecture du disque. Dans ce cas, retirez le disque et
attendez que l’humidité s’évapore.
Température à l’intérieur de la voiture : Si
votre voiture est restée garée pendant longtemps
dans un climat chaud ou froid, attendez que la
température à l’intérieur de la voiture redevienne
normale avant d’utiliser l’appareil.

[Maintenez pressée]

8 Écoute d’un disque
9 Connexion d’autres appareils

9 Écoute d’un autre appareil

10 Sélection d’un mode sonore

10 Utilisation des menus
13 Guide de dépannage
14 Utilisation de périphériques

15 Spécifications

15 Entretien

panneau de commande

disque

des affichages

extérieurs

extérieur

préréglé

Bluetooth ®

À propos des disques

Cet appareil ne peut lire que les CD comportant:

Disques qui ne peuvent pas être utilisés:

• Disques qui ne sont pas ronds

• Disques avec des colorations sur la surface
d’enregistrement ou disques sales

• Vous ne pouvez pas reproduire un disque
enregistrable/réinscriptible qui n’a pas été finalisé.
(Pour le processus de finalisation, reportez-vous
au logiciel utilisé pour graver le disque et au
mode d’emploi du graveur de disque.)

• Les CD de 3 pouces ne peuvent pas être
utilisés. Essayer d’insérer un disque à l’aide d’un
adaptateur peut entraîner un dysfonctionnement
de l’appareil.

FR02-15_KD-R322_R321[E_EU]f.indd 3 8/30/10 11:34:07 AM

Manipulation des disques:

• Ne pas toucher la surface d’enregistrement du
disque.

• Ne pas coller de ruban adhésif, etc. sur les disques
et ne pas utiliser de disque avec du ruban adhésif
collé dessus.

• N’utilisez aucun accessoire pour le disque.

• Nettoyez le disque en partant du centre vers
l’extérieur.

• Nettoyez le disque avec un chiffon sec au silicone
ou un chiffon doux. N’utilisez aucun solvant.

• Pour retirer les disques de cet appareil, tirez-les
horizontalement.

• Retirez les ébarbures du bord du trou central du
disque avant d’insérer un disque.

FRANÇAIS

3