JVC HR - S7950EU User Manual

VIDEO CASSETTE RECORDER

ENGLISH

CONTENTS

SAFETY FIRST 2

Safety Precautions ..................................2

INDEX 4 INSTALLING YOUR NEW RECORDER 10

Basic Connections ...............................10

S-VIDEO Connection ........................... 11

INITIAL SETTINGS 12

Auto Set Up ......................................... 12

Preset Download ................................. 14

Language .............................................16

SAT CONTROL SET 17

Satellite Receiver Control Setting .........17

T-V LINK 19

T-V Link Functions ...............................19

PLAYBACK 20

Basic Playback .....................................20

Playback Features ................................ 21

RECORDING 24

Basic Recording ................................... 24

Recording Features .............................. 25

B.E.S.T. Picture System ......................... 27

TIMER RECORDING 28

HOWVIEW

Express Timer Programming ................. 30

24 Hour Express Timer Programming ... 32 Automatic Satellite Programme

Recording ............................................ 35

PROGRAMME NAVIGATION 36

Navigation ........................................... 36

EDITING 40

Edit From A Camcorder ........................ 40

Edit To Or From Another

Video Recorder ....................................41

Output/Input Set ..................................42

SYSTEM CONNECTIONS 44

Connecting To A Satellite Receiver ......44

Connecting/Using A Decoder .............. 46

Connecting/Using A Stereo System ......47

SUBSIDIARY SETTINGS 48

Mode Set ............................................. 48

HOWVIEW

Tuner Set .............................................54

Clock Set .............................................60

Video Channel Set ............................... 62

TROUBLESHOOTING 63 QUESTIONS AND ANSWERS 66 SPECIFICATIONS 67 LIST OF TERMS 68

Timer Programming ......... 28

System Setup ....................53

LPT0651-001A

SAFETY FIRST

Safety Precautions

The rating plate and the safety caution are on the rear of the unit.

WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT

TO RAIN OR MOISTURE.

CAUTION

When you are not using the recorder for a long period of time, it is recommended that you disconnect

the power cord from the mains outlet. Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric

shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.

WARNING

There are two different types of SECAM colour systems: SECAM-L, used in FRANCE (also called SECAM-West), and SECAM-B, used in Eastern European countries (also called SECAM-East).

1. This recorder can also receive SECAM-B colour television signals for recording and playback.

2. Recordings made of SECAM-B television signals produce monochrome pictures if played back on a video recorder of SECAM-L standard, or do not produce normal colour pictures if played back on a PAL video recorder with SECAM-B system incorporated (even if the TV set is SECAM-compatible).

3. SECAM-L prerecorded cassettes or recordings made with a SECAM-L video recorder produce monochrome pictures when played back with this recorder.

4. This recorder cannot be used for the SECAM-L standard. Use a SECAM-L recorder to record SECAM-L signals.

IMPORTANT

Please read the various precautions on pages 2 and 3 before installing or operating the recorder.

It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without

the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.

● Cassettes marked “S-VHS” and “VHS” can be used with this video cassette recorder. However, S-VHS recordings are possible only with cassettes marked “S-VHS”. By using the S-VHS ET function, it is possible to record and play back with S-VHS picture quality on VHS cassettes with this recorder.

● S

HOWVIEW

from Gemstar Development Corporation.

is a registered trademark of Gemstar Development Corporation. The S

HOWVIEW

system is manufactured under licence

For Italy:

“It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.’95 published in the Official Gazette of the Italian Republic n. 301 of 28 Dec.’95”

The STANDBY/ON operating current on and off. “

Video tapes recorded with this video recorder in the LP/EP (Long Play/Extended Play) mode cannot be played back on a single-speed video recorder.

When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear.)

When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.

Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette.

1. DO NOT

... in an environment prone to extreme temperatures or humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are generated. ... on a surface that is unstable or subject to vibration.

2. DO NOT

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

3. DO NOT

4. DO NOT

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

5. DO NOT

6. DO NOT

filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this unit.

7. DO NOT

8. AVOID

place the recorder ...

block the recorder’s ventilation openings or holes.

place heavy objects on the recorder or remote control. place anything which might spill on top of the recorder or remote control.

expose the apparatus to dripping or splashing. use this equipment in a bathroom or places with water. Also DO NOT

place any naked flame sources, such as lighted candles, on the apparatus.

violent shocks to the recorder during transport.

button does not completely shut off mains power from the unit, but switches

” shows electrical power standby and “!” shows ON.

place any containers

MOISTURE CONDENSATION

Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.

ATTENTION:

To mobile phone users:

Using a mobile phone in the vicinity of the recorder may cause picture vibration on the TV screen or change the screen to a blue back display.

On placing the recorder:

Some TVs or other appliances generates strong magnetic fields. Do not place such appliance on top of the recorder as it may cause picture disturbance.

FRONT VIEW

INDEX

STANDBY/ON

Cassette Loading Slot

24H EXPRESS

S-VIDEO/VIDEO/AUDIO Input Connectors

pg. 40

墌

Stop/Eject

S-VHS ET Button 墌pg. 26

Front Display Panel 墌pg. 6

Button 墌pg. 12

Button 墌pg. 32

Button 墌pg. 20, 24

Connector cover

Attach the provided connector cover when you do not use the front panel connectors. To attach it, insert the cover’s left tab to the recorder’s front panel connector part, then push in the cover’s right side. To remove it, press the cover’s left side.

Infrared Beam Receiving Window

SAT

I J K L M

Button 墌pg. 35

Record Pa us e Play Advanced JOG Dial 墌pg. 20, 32

Button 墌pg. 24

Button 墌pg. 21

Button 墌pg. 20

REAR VIEW

Mains Power Cord 墌pg. 10

S VIDEO OUT Connector 墌pg. 11

AV1 (L-1) IN/OUT Connector

pg. 10, 41, 44, 45, 46

墌

SAT CONTROL Connector 墌pg. 17

ANT. IN Connector 墌pg. 10

AV2 (L-2) IN/DECODER Connector

pg. 17, 41, 44, 45, 46

墌

Remote PAUSE Connector 墌pg. 40

AUDIO OUT (L/R) Connectors 墌pg. 47

RF OUT Connector 墌pg. 10

FRONT DISPLAY PANEL

INDEX (cont.)

Instant REVIEW Indicator 墌pg. 22

Start Time Indicator ( ) 墌pg. 28, 32

S-VHS Indicator 墌pg. 26, 51

Stop Time Indicator ( ) 墌pg. 28, 32

VCR Indicator 墌pg. 25

Channel/Clock/Remain Display 墌pg. 15

Mode Display (L-1, L-2, F-1, S-1 or SAt*)

* When “L-2 SELECT” is set to “SAT” (墌pg. 43), “SAt” appears

instead of “L-2”.

“Timer” Indicator 墌pg. 29, 31, 32

Automatic Satellite Programme Recording

Indicator Play Indicator

Record Indicator

Counter Display

(The counter can display up to +/ – “19:59:59”. If the playback or recording time exceeds this limit the display starts to count from “0:00:00”.) Tape Speed SP/LP/EP 墌pg. 24

()

墌

pg. 35

ON-SCREEN DISPLAY

When “O.S.D.” is set to “ON” (墌pg. 49), various operational indicators appear on the TV screen.

Operation Mode Indicators

Tape Speed SP/LP/EP

Tape Direction

Index MARK Indicator 墌pg. 24

Counter Display

Tape Remaining Time Indicator 墌pg. 25

Audio Mode Display 墌pg. 23

Tape Position Indicator

The tape position indicator appears on the TV screen when you press

from the Stop mode or perform an Index Search (

pg. 22). The position of

墌

“

” in relation to “0” (beginning) or “+” (end) shows you where you are on the tape.

Beginning End

NOTE:

Depending on the type of tape being used, the tape position indicator may not appear correctly.

VPS/PDC Indicator 墌pg. 29, 31

Type of Broadcast 墌pg. 26

Current Day/Month/Year

Clock Display

Channel Position Number and Station Name/

Auxiliary Input Indicator (L-1, L-2, F-1, S-1 or SAT*)

* When “L-2 SELECT” is set to “SAT” (墌pg. 43), “SAT” appears

instead of “L-2”.

Timer Warning Display

A warning appears on the TV screen to tell you that the timer-recording is to start in 5 minutes if you’re not in the Timer mode at that time. The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press

on the remote control.

S-VHS ET Indicator (S-VHS ET : ON/S-VHS ET : OFF) 墌pg. 26, 51 “Cassette Loaded” Mark

REMOTE CONTROL

INDEX (cont.)

TV Button 墌“Operating JVC TVs” on page 9

TV/VCR Button 墌pg. 25 and “Operating JVC

TVs” on page 9 REVIEW Button 墌pg. 22

Number Keys 墌pg. 24, 28

VPS/PDC Button 墌pg. 29, 31

Cancel

0000 Button 墌pg. 25 STOP +/– Button 墌pg. 30

START +/– Button 墌pg. 30

PROG Button 墌pg. 28

Programme Check

Rewind

Record

Stop

MENU Button 墌pg. 16

r t

TV PR +/– Button 墌“Operating JVC TVs” on page 9 STANDBY/ON

AUDIO Button 墌pg. 23

on page 9 Display – – : – – Button 墌pg. 25

DAILY Button 墌pg. 29, 31

WEEKLY Button 墌pg. 29, 31

AUX Button 墌pg. 40

Timer

DATE +/– Button 墌pg. 30

PR +/– Button 墌pg. 24

Auto Tracking

SP/LP/EP Button 墌pg. 24 30 SEC Button 墌pg. 22

Play

Fast Forward

Pa us e

OK Button 墌pg. 13

Information Button*

* If you press this button when “O.S.D.” is set to “ON” (墌pg. 49),

you can see the current recorder status on the TV screen.

w e

TV page 9

Button 墌pg. 33

Button 墌pg. 20, 21

Button 墌pg. 24

Button 墌pg. 20, 24

Button 墌pg. 12

(TV Muting) Button 墌“Operating JVC TVs”

Button 墌pg. 29, 31

Button 墌pg. 23

Button 墌pg. 20

Button 墌pg. 20, 21

Button 墌pg. 21

Button 墌pg. 21, 22

+/– Button 墌“Operating JVC TVs” on

Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down the TV button. (

“Operating JVC TVs” below)

墌

This remote control transmits A code signals only; it is not applicable to B code signals.

How To Use

The remote control can operate most of your video recorder’s functions, as well as basic functions of JVC TV sets. (墌“Operating JVC TVs” below)

● Point the remote control toward the receiving window.

● The maximum operating distance of the remote control is about 8 m.

Operating JVC TVs

+/–

To operate your TV, while holding down the TV button, press the corresponding button: 1,

(TV Muting).

TV/VCR, TV PR

+/–

NOTES:

●

When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover.

●

Depending on the type of JVC TV, some or all functions may not be operated using the remote control.

●

If the remote control doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.

Basic Connections

Aerial connector

INSTALLING YOUR NEW RECORDER

It’s essential that your video recorder be properly connected.

THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

Back of TV

21-pin SCART cable (not provided)

Mains power cord

Back of recorder

21-pin SCART connector

AV1 (L-1) IN/OUT

Mains outlet

RF cable

(provided)

TV aerial cable

ANT. IN

RF OUT

Check the contents.

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” on page 67.

Situate the recorder.

Place the recorder on a stable, horizontal surface.

Connect the recorder to TV.

The connection method you use depends on the type of TV you have.

RF Connection

To connect to a TV with NO AV input connectors . . .

Disconnect the TV aerial cable from the TV.

Connect the TV aerial cable to the ANT. IN connector

on the rear panel of the recorder. Connect the provided RF cable between the RF OUT

connector on the rear panel of the recorder and the TV’s aerial connector.

AV C onnection

To connect to a TV with AV input connectors . . .

Connect the aerial, recorder and TV as per “RF

Connection”. Connect an optional 21-pin SCART cable between the

AV1 (L-1) IN/OUT connector on the rear panel of the recorder and the TV’s 21-pin SCART connector.

Make AV connection if your TV has a 21-pin AV input connector (SCART) in order to reduce the possibility of interference. With AV connection, you can enjoy stereo playback of video tapes if you are using a stereo TV.

NOTES:

●

The AV1 (L-1) IN/OUT connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). If your TV’s 21-pin AV input connector (SCART) is compatible with the Y/C signal, set “L-1 OUTPUT” to “S-VIDEO” after the connection and the initial settings are completed ( high-quality S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

●

Set your TV to the VIDEO (or AV), Y/C, or RGB mode according to the type of your TV’s SCART connector.

●

For switching the TV’s mode, refer to the instruction manual of your television.

●

To obtain high-quality S-VHS pictures, you can also use the S-VIDEO connection described on page 11.

墌

pg. 42). You can obtain

Connect the recorder to mains.

Plug the end of the mains power cord into a mains outlet.

After the connection is completed, perform “Auto Set Up” on page 12.

S-VIDEO Connection

Back of TV

Aerial connector

power cord

Back of recorder

AUDIO IN connectors

S-VIDEO IN connector

Mains outlet

Mains

S VIDEO OUT

RF cable (provided)

S-Video cable (not provided)

Audio cable

(not provided)

TV aerial cable

AUDIO OUT

To connect to a TV with S-VIDEO/AUDIO IN connectors . . .

Connect the recorder to TV.

Connect the aerial, recorder and TV as per “RF

Connection” ( Connect the recorder’s S VIDEO OUT connector to

the TV’s S-VIDEO IN connector. Connect the recorder’s AUDIO OUT connectors to the

TV’s AUDIO IN connectors.

Connect the recorder to mains.

Plug the end of the mains power cord into a mains outlet.

墌

pg. 10).

NOTES:

●

You can obtain high-quality S-VHS pictures.

●

With S-VIDEO connection, you cannot use the Preset Download function (

●

If your TV is not stereo-capable, use the recorder’s AUDIO OUT connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction. (

●

To operate the recorder with your TV using the S-VIDEO connection, set your TV to its AV mode.

●

For switching the TV’s mode, refer to the instruction manual of your television.

After the connection is completed, perform “Auto Set Up” on page 12.

墌

pg. 14).

墌

pg. 47)

Auto Set Up

Auto Channel Set/Auto Clock Set/ Auto Guide Program Number Set

INITIAL SETTINGS

Before starting, make sure of the following:

● The TV aerial cable should be connected to the recorder.

● The recorder’s mains power cord should be connected to a

mains outlet.

● The TV should be set to its AV mode (with AV connection pg. 10) or UHF channel 36 (with RF connection

墌

pg. 10).

墌

After the pressed for the first time to power on the recorder selecting your country*, the Auto Set Up function sets the tuner channels, clock** and Guide Program numbers automatically.

* If you live in Belgium (BELGIUM) or Switzerland (SUISSE), you also

**If you live in Hungary (MAGYARORSZÁG), Czech Republic (

button on the recorder or remote control is

need to select your language.

REPUBLIKA), Poland (POLSKA) or other countries in Eastern Europe (OTHER EASTERN EUROPE), set the clock manually.

, by simply

ESKÁ

Turn on the recorder.

Press 1 on the recorder or remote control. The Country Set display appears on the TV screen.

NOTE:

If you have connected your TV to the recorder with RF connection and the on-screen display appearing on UHF channel 36 looks distorted, perform “Video Channel Set” on page 62.

Select your country.

Press rt to move the highlight bar (pointer) to your country’s name.

(Example) DEUTSCHLAND is selected.

NOTES:

●

If you have selected BELGIUM or SUISSE, go to step3.

●

If you have selected MAGYARORSZÁG, POLSKA or OTHER EASTERN EUROPE, press OK. The Clock Set screen appears. Set the clock manually ( go to step 4.

●

If you have selected any other country name, go to step 4.

ESKÁ REPUBLIKA,

墌

pg. 60), then

Select the language.

Press OK. The Language Set display appears on the TV screen. Press highlight bar (pointer) to the language of your choice.

(Example) DEUTSCH is selected.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press

On the on-screen display

Press highlight bar (pointer) to “AUTO SET” and press OK or

“Auto” blinks on the front display panel; do NOT press any button on the recorder or remote control until the front display panel shows either the display as illustrated in step 5 or “– –:– –” as illustrated on page 15.

● If you are using the on-screen display, the AUTO SET screen will appear. As Auto Set Up progresses, the “ mark on the TV screen moves from left to right.

● When you have connected the video recorder to a TV offering T-V Link via a fully-wired 21-pin SCART cable ( the TV is turned on, the recorder automatically performs the Preset Download ( “AUTO SET” for Auto Set Up function.

to move the

Perform Auto Set Up.

to select “Auto” and press OK or e.

to move the

”

Beginning End

pg. 14) even if you select “Auto” or

墌

pg. 10) and

墌

Confirm/Set video channel.

With RF connection

The video channel that is shown on the display panel is your video channel. Press OK.

● If you have selected MAGYARORSZÁG, CESKÁ REPUBLIKA, POLSKA or OTHER EASTERN EUROPE in step2 on page 12, “2” appears instead of “1”.

● To view picture signals from the recorder, set your TV to the video channel.

With AV connection

Press panel shows “1 – –” (or “2 – –”). Now the video channel is set to off. Then press OK.

● To view picture signals from the recorder, set your TV to its AV mode.

until the display

PR –

ATTENTION

Once you have performed Auto Set Up, even if the recorder’s memory backup has expired, all the stored stations and their Guide Program numbers remain in the recorder’s memory and the recorder will not perform Auto Set Up again. You only need to set the clock. ( If you have moved to a different area, perform each setting as required.

● Video channel setting (for RF connection users)

● Tuner setting

● Clock setting

If a new station starts broadcasting in your area, perform tuner setting ( setting (

墌

pg. 54

墌

pg. 60

墌

pg. 54) and, if necessary, video channel

墌

pg. 62).

墌

pg. 60)

墌

pg. 62

NOTES:

● In the area where no TV station transmits a PDC (Programme Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.

● If there is a power cut, or if you press Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the recorder power once and try again from step 1.

● Auto Clock Set may not function properly depending on the reception condition.

● If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels (

pg. 57, “INFORMATION”).

墌

or MENU while Auto

Preset Download

Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide

INITIAL SETTINGS (cont.)

If you have connected the recorder to your TV via the AV connection ( Preset Download instead of the Auto Set Up in step 4 on page 13. After downloading, the recorder sets the clock and Guide Program numbers automatically.

Perform steps 1 to 3 of “Auto Set Up” on page 12 before continuing.

pg. 10), the recorder will automatically perform

墌

Program Number Set

ATTENTION

You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.

* Compatible with TVs offering T-V Link, EasyLink, Megalogic,

SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

Perform Preset Download.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press

On the on-screen display

Press highlight bar (pointer) to “T-V LINK” and press OK or

Preset positions on the front display panel increase from “CH1”; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 15.

● If you are using the on-screen display, the T-V LINK screen will appear. Then the GUIDE PROG SET screen will appear during Guide Program Number Set. When Preset Download is completed, “COMPLETED” appears for about 5 seconds, then the normal screen appears.

● If you press any button on the recorder or remote control while downloading is in progress, it will be interrupted.

to select “CH – –” and press OK or e.

to move the

NOTES:

●

For details, refer to the instruction manual of your TV.

●

In the area where no TV station transmits a PDC (Programme Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.

●

If there is a power cut, or if you press downloading or set up is in progress, it will be interrupted; be sure to turn off the recorder power once and try again from the beginning.

●

Auto Clock Set may not function properly depending on the reception condition.

●

On this recorder, the characters available for station names (ID) are A–Z, 0–9, –, downloaded stations may differ from those of your TV

墌

(

pg. 58).

, + and I (space). Some names of

while

Set the video channel.

Set the video channel to off manually. (墌pg. 62)

Results of Auto Set Up/Preset Download appear on the front display panel

If both Auto Channel Set and Auto Clock Set have been performed successfully, the correct current time is displayed.

Turn on the TV and select its video channel or AV mode, then make sure that all necessary stations have been stored in the recorder’s memory by using the PR button(s).

● If station names (ID – will be displayed at the top left corner of the TV screen for about 5 seconds when the recorder is tuned to a different station.

● If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 56 – 59.

If Auto Channel Set has succeeded but Auto Clock Set has not, “1” (channel position) is displayed.

Turn on the TV and select its video channel or AV mode, then make sure that all necessary

stations have been stored in the recorder’s memory by using the PR button(s).

● If station names (ID – will be displayed at the top left corner of the TV screen for about 5 seconds when the recorder is tuned to a different station.

● If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 56 – 59.

Perform “Clock Set” on page 60.

If both Auto Channel Set and Auto Clock Set have failed, “– –:– –” is displayed.

Make sure the cables are connected properly and turn off the recorder’s power once, then turn the recorder’s power back on again. The Country Set display appears on the TV screen; perform “Auto Set Up” on page 12 or “Preset Download” on page 14 again.

pg. 59) have also been stored in the recorder’s memory, the station name

墌

pg. 59) have also been stored in the recorder’s memory, the station name

墌

IMPORTANT

● To check if the Guide Program numbers have been set correctly, perform the S

● In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work

properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the S system, the recorder will record a TV programme of a different station. When programming the timer using the S system, be sure to check the desired channel is selected correctly (

● Your video recorder memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture (

pg. 57, “Delete A Channel”).

墌

HOWVIEW

pg. 28, “S

Timer Programming (墌pg. 28).

HOWVIEW

Timer Programming”).

HOWVIEW HOWVIEW

INFORMATION

Language for the on-screen display

Auto Set Up also selects the language automatically for the on-screen display depending on the Country setting you have made in step 2 on page 12 (unless you have selected BELGIUM or SUISSE), as shown below.

SUOMI PORTUGAL DEUTSCHLAND POLSKA NORGE SVERIGE

If you want to change the language setting manually, see “Language” on page 16.

Just Clock

Your recorder is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to “ON” (

pg. 60, “Just Clock”).

墌

SUOMI DANMARK

]

ENGLISH ÖSTERREICH

]

DEUTSCH

]

POLSKI ITALIA

]

NORSK MAGYARORSZÁG]MAGYAR

]

SVENSKA ESPAÑA

]

ESKÁ REPUBLIKA

] ] ] ]

]

DANSK NEDERLAND DEUTSCH GREECE

CEc

TINA OTHER WESTERN EUROPE

ITALIANO OTHER EASTERN EUROPE]ENGLISH

CASTELLANO

NEDERLANDS

]

ENGLISH

]

ENGLISH

]

Language

Turn on the TV and select the video channel (or AV mode).

INITIAL SETTINGS (cont.)

This recorder offers you the choice to view on-screen messages in 13 different languages. Though Auto Set Up selects the language automatically (墌pg. 15), you can change the language setting manually as required.

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “AUTO CH SET”, then press

Press rt to move the highlight bar (pointer) to your country’s name, then press OK or

Access the Country Set screen.

Select your country.

Select the language.

Press highlight bar (pointer) to the language of your choice.

● You do not have to press OK; pressing OK enters AUTO SET/ T-V LINK screen.

Press

to move the

Return to the normal screen.

SAT CONTROL SET

Satellite Receiver Control Setting

The following procedure is required if you receive satellite channels through a satellite receiver. Approximately 20 seconds before the S programming ( (

pg. 30) starts, the recorder sets its input mode to “L-2”

墌

and automatically switches the satellite receiver’s channels using an optional Satellite Controller.

pg. 28) or Express timer programming

墌

HOWVIEW

timer

Your recorder

Satellite receiver

21-pin SCART cable (not provided)

Satellite Controller

(not provided)

Satellite receiver

Satellite Controller (suggested locations)

Transmitter

Installing Satellite Controller

Situate the Satellite Controller.

Place the Satellite Controller so that the path between its transmitter and the satellite receiver’s remote sensor is unobstructed.

Attach the Satellite Controller.

Fix securely using the adhesive strip attached on the back of the Satellite Controller.

Make connections.

Be sure to connect the recorder’s AV2 (L-2) IN/DECODER connector to the satellite receiver’s 21-pin SCART connector.

NOTE:

When connecting your satellite receiver, refer to its instruction manual.

Connect the Satellite Controller to recorder.

Connect the Satellite Controller to the SAT CONTROL connector on the rear panel.

AV2 (L-2) IN/DECODER

Back of recorder

SAT CONTROL

SAT CONTROL SET (cont.)

Access the Initial Set screen.

Press rt to move the highlight bar (pointer) to “INITIAL SET”, then press OK or

Access the Sat Control Set screen.

Press rt to move the highlight bar (pointer) to “SAT CONTROL SET”, then press OK or

Press the appropriate

to enter the brand code

keys

from the list on page 19, then press OK.

● If the brand code you entered is invalid, the code field will be reset. Enter the correct brand code again.

● If the recorder is in playback or recording mode, you cannot set the brand code.

Enter the satellite receiver’s brand.

number

Setting satellite receiver's brand and channel

After installation, set the satellite receiver’s brand and channel correctly; otherwise, the Satellite Controller cannot work correctly.

Turn on the TV and select the video channel (or AV mode).

Turn on the satellite receiver.

Turn on the satellite receiver’s power.

Access the Main Menu screen on the

recorder.

Press

Select the satellite receiver’s channel for

testing.

Press the appropriate

to enter one of the

keys

channel positions on the satellite receiver, then press

● You can select the channel position between 1 to 999.

● After pressing OK, the recorder enters the Test mode.

number

SAT CONTROL SET (cont.) T-V LINK

Check the result of the test.

If the satellite receiver’s channel number has been changed to the same one as you set in step 6 ...

Press bar (pointer) to “CHANGED TO ...”, then press OK or finish the Sat Control Set mode.

If the satellite receiver’s channel number has not been changed correctly ...

Press CHANGED”, then press OK or procedure again from step 5.

BRAND NAME CODE

JVC AMSTRAD CANAL SATELLITE CANAL + D-BOX ECHOSTAR (VIA DIGITAL) FINLUX FORCE GALAXIS GRUNDIG HIRSCHMANN HUMAX ITT NOKIA KATHREIN LUXOR MASCOM MASPRO NOKIA PACE PANASONIC PHILIPS RADIX RFT SABA SAGEM SALORA SAMSUNG SIEMENS SKYMASTER TECHNISAT THOMSON TPS TRIAX WISI

to move the highlight

to move the highlight bar (pointer) to “NOT

. Then perform the

73 60, 61, 62, 63, 92 81 81 85 82 68 89 88 64, 65, 102 64, 78, 99 88 68 70, 71, 96 68 93 70 87, 94 65, 67, 74, 86, 92 74, 92 66, 84, 101 78 69 97 83, 90 68 83 64 69, 98 66, 100 97 83 91 64

T-V Link Functions

When you connect the recorder to your TV via a fully-wired 21-pin SCART cable ( available. You can use these functions only with a TV offering T-V Link, etc.* For details, refer to the instruction manual of your TV.

* Compatible with TVs offering T-V Link, EasyLink, Megalogic,

SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

NexTView Link

You can download the EPG (Electronic Programme Guide) information from your TV for timer-programming on the recorder. For details, refer to the instruction manual of your TV.

TV Auto Power On

The TV will turn on and be set to its AV mode automatically whenever you play a tape. For details, refer to the instruction manual of your TV.

VCR Auto Standby

You can use your TV’s remote control to turn off the recorder. For details, refer to the instruction manual of your TV.

Direct Rec

You can easily start recording the programme that you are watching on your TV. When you use this function, set “DIRECT REC” to “ON” (

墌

pg. 10), the following functions are

墌

pg. 50).

NOTES:

●

The Satellite Controller may not work with all types of satellite receiver.

●

For some satellite receivers, you need to set its channel input mode to 2-digit.

●

If your satellite receiver has more than two channel modes, be sure to set to “All Channel Mode”. For details, refer to the instruction manual of the satellite receiver.

●

When selecting the satellite receiver’s channel ( signals from the remote control may interfere with signals transmitted from the Satellite Controller. In this case, move the remote control as close to the recorder’s infrared beam receiving window as possible.

墌

step 6),

Basic Playback

Turn on the TV and select the video channel (or AV mode).

PLAYBACK

Load a cassette.

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointed toward the recorder.

● Do not apply too much pressure when inserting.

● If the record safety tab has been removed, playback begins

automatically.

● If the record safety tab is intact, the recorder checks the tape information for Programme Navigation. For details, refer to “Navigation” (

Find the programme start point.

If the tape is advanced past the start point, press 3 or turn the turn the

Press 4. “bESt” appears blinking in the recorder’s front display panel during automatic tracking. (

Press 8 on the remote control or front panel. Then press

JOG JOG

Start playback.

Stop playback.

pg. 36).

墌

dial to the left. To go forward, press 5 or dial to the right.

pg. 27)

墌

on the recorder’s

to remove the cassette.

Clean the video heads using a dry cleaning cassette — TCL-2 — when:

● Rough, poor picture appears while a tape is played back.

● The picture is unclear or no picture appears.

● “USE CLEANING CASSETTE” appears on the screen (only

with “O.S.D.” set to “ON” (

墌

pg. 49)).

NOTE:

The heads get dirty in the following cases:

● in an environment prone to extreme temperature or humidity

● in a dusty environment

● flaw, dirt or mold on video tapes

● continuous usage for a long time

Usable cassettes

● Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.

● This video recorder can record on regular VHS and Super VHS cassettes. While only VHS signals can be recorded on regular VHS cassettes*, both VHS and Super VHS signals can be recorded and played back using Super VHS cassettes.

* By using the S-VHS ET function, it is possible to record and

play back with S-VHS picture quality on VHS cassettes with this recorder.

Playback Features

NOTES:

● For speed search, refer to the table below.

● You can see smooth slow motion picture only during 1/2x

slow motion playback.

● You can hear the normal audio track only during 1.5x speed search.

Reverse

–7, –5, –3

Reverse

play

–1

Reverse

slow

motion

–1/6, –1/18

Slow

motion

1/18, 1/6, 1/2*

Normal

Forward

play

* PAL SP/LP only

1.5*,2, 3, 5, 7

Still Picture/Frame-By-Frame Playback

Pause during playback.

Push the

Press 9.

Activate frame-by-frame playback.

Tur n t h e playback, or to the left for reverse frame-by-frame playback.

Press 9.

Press w or e.

dial.

JOG

dial to the right for forward frame-by-frame

JOG

To resume normal playback, press 4 or push the dial.

JOG

Slow Motion

During playback, turn the for forward slow motion. To play in reverse slow motion, continue to turn the the forward direction slow motion modes.

JOG

During still picture, press and hold 9 for 2 seconds, then release. Press picture.

and release again to return to still

During still picture, press and hold w or e. Release to return to still picture.

NOTE:

During slow motion playback, some noise may appear on the TV screen. Press PR + or – on the remote control to eliminate the noises.

dial one click to the left

JOG

dial to the left after selecting all

High-Speed (Turbo) Search

During playback, turn the right.

During playback or still, press 5 for forward high-speed search, or

dial quickly to the left or

JOG

for reverse high-speed search.

ATTEN T I O N

● Picture may not appear during high-speed search with an LP/EP-recorded tape.

● Noise may appear or the picture may appear distorted with an EP-recorded tape during still, slow motion, frame-by-frame playback or variable speed search.

● In the high-speed search, still, slow motion or frame-by-frame playback mode, the picture will be distorted, and there will be a loss of colour.

NOTE:

For short searches, press and hold 5 or 3 for over 2 seconds during playback or still picture. When released, normal playback resumes.

To resume normal playback, press

PLAYBACK (cont.)

Variable Speed Search

During playback, turn the forward variable-speed search, or to the left for reverse variable-speed search.

During playback, press w or e.

● The more times you press, the faster the playback picture moves.

● To decrease speed, press the button for the opposite direction.

To resume normal playback, press 4.

dial to the right for

JOG

Index Search

Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction.

NOTE:

Before starting, make sure the recorder is in the Stop mode.

Activate Index Search.

Press w or e (2 or 6). “2 1” or “6 1” is displayed on the TV screen and search begins in the corresponding direction.

● To access index codes 2 through 9, press w until the correct index number is displayed.

Example:

To locate the beginning of B from the current position, press twice. To locate the beginning of D from the current position, press once.

Current position

or e repeatedly

Skip Search

During playback, press unwanted sections. Each press initiates a 30-second period of fast-motion playback. Normal playback resumes automatically.

To resume normal playback during a Skip Search, press

1 to 4 times to skip over

30 SEC

Instant ReView

Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer-recorded programme. If you have several programmes recorded, you can easily access any of them.

NOTE:

Before starting, make sure that the recorder is off and that the Timer mode is disengaged.

Activate Instant ReView.

Press

REVIEW

recorder searches for the index code indicating the start of the last timer-recorded programme. Once it’s found, playback begins automatically.

● The front display panel tells you how many programmes have been timer-recorded. If you have, for example, 3 programmes, the Instant REVIEW indicator ( ) and “3” blink. To watch the first of the 3 programmes, press recorder searches and begins playback automatically. You can access a programme as far as 9 index codes away from the

current tape position.

● The number of recorded programmes will not be displayed on the front display panel after Auto Satellite Programme Recording (

. The recorder power comes on and the

three times

REVIEW

pg. 35).

墌

. The

Index number

● When the specified index code is located, playback begins automatically.

+ 50 hidden pages

JVC HR - S7950EU User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Safety Precautions

FRONT VIEW

REAR VIEW

FRONT DISPLAY PANEL

ON-SCREEN DISPLAY

REMOTE CONTROL

Basic Connections

S-VIDEO Connection

Auto Set Up

Preset Download

Language

Satellite Receiver Control Setting

T-V Link Functions

Basic Playback

Playback Features