JVC HR-S7900U User Manual

Download

VIDEO CASSETTE RECORDER

HR-S7900U

MBRSET

CABLE/

DBS

A/B

POWER

TV/VCR

DISPLAY

A. MONITOR

123

456

DBS

DAILY(M-F)

WEEKLY

AUX

C.RESET

CANCEL

TIMER

START STOP DATE

EXPRESS PROGRAMMING

PROG

PROG SP/EP SKIP SEARCH

CHECK

REW

REC

–

REMOTE CONTROL UNIT

SHUTTLE

MULTI BRAND

PLAY

STOP

PAUSE

PLUS

–

POWER

S VIDEO

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

A.DUB

INSERT

24HR QUICK

PROGRAM

PLAY

REW

–

REC PAUSE STOP/EJECT

CH– /+

PUSH / TURN

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial No. which are located on the rear of cabinet. Retain this information for future reference.

Model No. Serial No.

LPT0504-001A

Dear Customer,

Thank you for purchasing the JVC S-VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new VCR.

CAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

This video cassette recorder should be used with AC 120V`, 60Hz only. To prevent electric shocks and fire hazards, DO NOT use any other power source.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Declaration of Conformity Model Number :HR-S7900U Trade Name :JVC Responsible Party :JVC Americas Corp. Address :1700 Valley Road Wayne,

N.J. 07470

Telephone Number :973-315-5000

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Failure to heed the following precautions may result in damage to the VCR, Remote or video cassette.

1. DO NOT place the VCR . . .

... in an environment prone to extreme temperatures or

humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are

generated. ... on a surface that is unstable or subject to vibration.

2. DO NOT block the VCR’s ventilation openings.

3. DO NOT place heavy objects on the VCR or on the Remote.

4. DO NOT place anything which might spill on the top of the VCR or on the Remote.

5. AVOID violent shocks to the VCR during transport.

VCR Plus+, C3 and PlusCode are registered trademarks of Gemstar Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar Development Corporation.

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

CAUTION:

Changes or modifications not approved by JVC could void user’s authority to operate the equipment.

n Cassettes marked "S-VHS" and "VHS" can be used with this

video cassette recorder. However, S-VHS recordings are possible only with cassettes marked "S-VHS". By using S-VHS ET it is possible to record and play back with S-VHS picture quality on VHS cassettes with this VCR.

n As an ENERGY STA R® Partner, JVC has determined that this

product or product model meets the ENERGY STAR® guidelines for energy efficiency.

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.

INSTALLATION

1. Grounding or Polarization

(A) Your product may be equipped with a polarized alternating-

current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

(B) Your product may be equipped with a 3-wire grounding-type

plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

2. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

5. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

• Do not block the openings by placing the product on a bed,

sofa, rug or other similar surface.

• Do not place the product in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA INSTALLATION INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

3. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

ANTENNA LEAD IN WIRE

GROUND CLAMP

ANTENNA DISCHARGE UNIT (NEC SECTION

ELECTRIC SERVICE EQUIPMENT

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

USE

1. Accessories

To avoid personal injury:

• Do not place this product on an unstable cart, stand, tripod, bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.

• Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.

• Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.

• Do not try to roll a cart with small casters across thresholds or deep-pile carpets.

2. Product and Cart Combination

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

3. Water and Moisture

Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.

4. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

5. Attachments

Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.

6. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

7. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

PORTABLE CART WARNING (Symbol provided by RETAC)

SERVICING

1. Servicing

If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power supply cord or plug is damaged. b.If liquid has been spilled, or objects have fallen into the

product. c.If the product has been exposed to rain or water. d.If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation. e.If the product has been dropped or damaged in any way. f. When the product exhibits a distinct change in

performance—this indicates a need for service.

3. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or which have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

4. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.

HOW TO USE THIS INSTRUCTION MANUAL

● The Index on pages 60 – 64 lists frequently-used terms, and

the number of the page on which they are used or explained

in the manual. This section also illustrates the controls and

connections on the front and rear panel, the front display

panel and the Remote.

● The Z mark signals a reference to another page for

instructions or related information.

● Operation buttons necessary for the various procedures are

clearly indicated through the use of illustrations at the

beginning of each major section.

BEFORE YOU INSTALL YOUR NEW VCR . . .

. . . please read the sections/literature listed below.

● ”CAUTIONS” on page 2

● ”IMPORTANT PRODUCT SAFETY INSTRUCTIONS” on the

INSTALLING YOUR NEW VCR 6

Basic Connections .................................. 6

INITIAL SETTINGS 8

Plug & Play Setting ................................ 8

Auto Clock Set/Auto Tuner Set ................................... 8

Language Setting ................................... 9

Clock Setting........................................ 10

Preparations.............................................................10

Setting clock semiautomatically

— Semiauto Clock Set ............................................. 11

Setting clock manually

— Manual Clock Set ................................................12

Tuner Setting ....................................... 13

Setting channels automatically

— Auto Channel Set ................................................13

Setting channels manually

— Manual Channel Set ............................................14

Cable Box Control Setting .................... 15

Installing Controller .................................................15

Setting cable box output channel & brand ...............16

DBS Receiver Control Setting ................18

Installing Controller .................................................18

Setting DBS receiver output channel & brand ..........19

BASIC PLAYBACK AND RECORDING 21

Basic Playback .................................... 21

To stop playback ......................................................21

To rewind the tape ...................................................21

To fast-forward the tape ...........................................21

To eject the tape ......................................................21

To turn off the VCR .................................................. 21

Basic Playback Features ...................... 22

Changing display information ..................................22

Checking tape position ............................................22

Playing back tape repeatedly — Repeat Play ........... 22

Adjusting tracking condition

— Tracking Adjustments .......................................... 23

Selecting monitor sound — Audio Monitor ..............23

Automatic operations after rewinding

— Next Function Memory .......................................23

Locating beginning of recordings

— Index Search .......................................................23

Locating beginning of timer recordings

— Instant Review.....................................................24

Adjusting picture condition

— Digital TBC/NR ...................................................24

Basic Recording ................................... 25

To pause recording ..................................................25

To stop recording .....................................................25

To rewind the tape (when it is not running) ..............25

To fast-forward the tape (when it is not running) ......25

To eject the tape ......................................................25

To turn off the VCR .................................................. 25

Basic Recording Features ..................... 26

Changing display information ..................................26

Specifying recording length

— Instant Timer Recording (ITR) ..............................26

Watching one program while recording another ......26

Showing on-screen display ......................................27

SPECIAL EFFECT PLAYBACK 28

Special Effect Playback ........................ 28

Locating particular scene rapidly

— Picture Search .....................................................28

Viewing still picture — Still Picture Playback...........29

Skipping unwanted portions — Skip Search .............29

Viewing still picture frame by frame

— Frame-by-Frame Playback ...................................29

Viewing slow motion picture

— Slow Motion Playback ........................................ 29

TIMER RECORDING 30

VCR Plus+® Timer Programing .............. 30

Changing VCR Plus+® Setting................32

Express Timer Programing ................... 34

24HR Quick Programing ...................... 36

Checking program settings .......................................37

Canceling or changing program settings .................. 37

When programs overlap each other .........................38

OTHER USEFUL FUNCTIONS 39

Useful Function Settings .......................39

Satellite Auto Recording ....................... 44

Child Lock ............................................45

EDITING 46

Edit From Camcorder ...........................46

Edit To Or From Another VCR ............... 48

Audio Dubbing .................................... 49

Insert Editing and AV Dubbing ............. 50

MULTI-BRAND REMOTE CONTROL 52

TV Brand Setting .................................. 52

Cable Box Brand Setting ...................... 53

DBS Receiver Brand Setting ..................54

Changing Remote Control Code ............ 55

TROUBLESHOOTING 56

Questions and answers ............................................59

INDEX 60

List of terms .............................................................60

Front panel ..............................................................61

Front display panel ..................................................62

Rear panel ...............................................................63

On-screen display....................................................63

Remote ....................................................................64

SPECIFICATIONS 65

FOR SERVICING (Only in U.S.A.) 66

WARRANTY (Only in U.S.A.) 67

Basic Connections

Antenna or cable

Matching transformer

AC Power Cord

VIDEO OUT

AUDIO OUT

S V

I D E O

IN OUT

(not supplied)

CABLE

BOX

INSTALLING YOUR NEW VCR

ANTENNA IN (Antenna or cable input)

Coaxial cable

Flat feeder

REMOTE

OUT

PAUSE/ AV COMPU

-LINK AUDIO

VIDEO

ANTENNA IN

VHF/UHF

TV OUT

Back of VCR

AC Outlet

To S-video input connector

S VIDEO OUT

S-video cable (supplied)

To Audio/video input connectors

To 75 ohm terminal

TV OUT

Audio/video cable (supplied)

RF cable (supplied)

Check contents

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (Z␣ pg.␣ 65).

Situate VCR

Place the VCR on a stable, horizontal surface.

Connect VCR to TV

The following connections are required.

RF Connection

1 Disconnect the TV antenna from the TV. 2 Connect the TV antenna cable to the

ANTENNA IN terminal on the rear of the VCR.

3 Connect the supplied RF cable between the TV

OUT terminal on the rear of the VCR and the TV’s antenna input terminal.

AV Connection (improves picture quality during tape playback.)

If your TV is equipped with audio/video input connectors

1 Connect the antenna, VCR and TV as shown in

the illustration.

2 Connect an audio/video cable between the

AUDIO/VIDEO OUT connectors on the rear of the VCR and the audio/video input connectors on the TV.

S-video Connection (allows you to make the most of the S-VHS picture performance.)

If your TV is equipped with an S-video input connector

1 Perform “RF Connection” and RED/WHITE

AUDIO connections.

2 Connect an S-video cable between the S VIDEO

OUT connector on the rear of the VCR and the S-video input connector on the TV.

Set VCR channel

Press POWER to turn off the VCR and press STOP/ EJECT ( § ) on the front panel for more than

5␣ seconds. “3CH” appears on the display panel. Press CH + and – on the Remote to select “3CH” or “4CH” for only RF connection, “–CH” (OFF) for RF and AV connection, then press OK.

● The VCR channel is preset to 3CH. Set to 4CH if 3CH is used for broadcasting in your area. (To view the picture from this VCR through this channel, select the same channel on the TV with the VCR channel setting on the VCR.)

● You can now perform basic playback (Z␣ pg.␣ 21) or basic recording (Z␣ pg.␣ 25).

NOTES:

●

The VCR channel is the channel on which you can watch the picture from the VCR on the TV when only using the RF connection.

●

Even if you are using audio/video cables to connect your VCR to your TV, you must also connect it using the RF cable. This will ensure that you can record one show while watching another (Z pg. 26).

●

For full identification of the VCR’s rear panel, refer to the Index ( Z pg. 63).

Connect VCR to power source

Connect the AC power plug to an AC outlet.

● The clock and tuner channels will automatically be set when the antenna is connected and when the AC power cord is first connected to an AC power outlet (Z pg. 8). (If “Auto” or “CH” is displayed on the front display panel before the VCR is turned on, the clock and tuner channels are being set automatically. Wait until the clock time is displayed on the front display panel before turning on the VCR.)

Plug & Play Setting

Auto Clock Set/Auto Tuner Set

ATTENTION

● If you use a cable box, Plug & Play will not function; set the clock and tuner channels separately. (Z pg.10 – 14)

● It takes several minutes for the VCR to complete the Plug & Play setting.

● Do not press any buttons on the front panel or on the Remote while Plug & Play is in progress.

REW

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

S VIDEO

PLAY

A.DUB

24HR QUICK PROGRAM

INSERT

–

REC PAUSE STOP/EJECT

CH– /+

PUSH / TURN

INITIAL SETTINGS

This VCR sets the clock and tuner channels automatically when AC power cord is first connected to an AC outlet. The antenna cable must be connected for the Plug & Play setting. The time and date can be set automatically by the clock setting data transmitted from one of the regular TV broadcast channels. We call this TV channel the “host channel” and it is a PBS channel in your area.

Perform Plug & Play setup

Connect the antenna cable to the VCR (Z pg.

6). Then connect the AC power cord to an AC outlet. Do not turn on the VCR.

The clock and tuner channels will be set automatically.

NOTES:

●

Auto Clock Set is performed first. “Auto” blinks on the front display panel during Auto Clock Set.

●

Auto Channel Set is performed next. Auto Channel Set scans all the channels that are receivable by your VCR. During Auto Channel Set, the channel numbers are displayed as they are scanned and set.

●

When Plug & Play setting has been complete successfully, the correct clock time is displayed. If you perform Plug & Play setting successfully, there is no need to perform the clock (Z pg. 10) and tuner (Z pg.

13) settings. If, however, you want to add or delete channels, refer to Manual Channel Set on page 14.

During Initial Auto Clock Set

“Auto” blinks.

During Auto Channel Set

The channel numbers are displayed as they are scanned and set.

Plug & Play Completed

The current time (including AM/PM) is displayed.

* If an incorrect clock time or “– –:– –” appears on the display panel, see “What to do if Plug & Play setting failed”

below.

INFORMATION

● If “AUTO CLOCK” is set to “ON” on the Clock Set screen on page 11, the clock will be adjusted automatically by the host channel every hour (except 11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming PBS channel clock setting data. (This automatic clock adjustment can only be performed when the VCR is turned off. The clock will be adjusted just on these hours — on the time displayed on the front display panel, not on the actual real time.) The default setting of “AUTO CLOCK” is “ON”.

● If the memory backup fails, because a power outage occurs or because the AC power cord is unplugged, Plug & Play will be performed when power is restored to the VCR.

● Poor antenna or cable signal may prevent the VCR from receiving the Auto clock setting data from the PBS channel. If this function is taking a considerable amount of time, it may be necessary to perform the Semiauto or Manual Clock Set procedure.

What to do if Plug & Play setting failed

● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform the Semiauto (Z pg. 11) or Manual Clock Set (Z pg. 12) procedure.

● If “- -:- -” appears on the front display panel, your antenna cable may not be connected to the VCR or there may not be a Host PBS signal available in your area. Ensure that the antenna cable is connected correctly. Then turn on and off the VCR; the Plug & Play setting will be automatically reactivated. If Plug & Play setting is not performed though the antenna cable is connected correctly, perform Manual Clock Set (Z pg. 12) and Auto Channel Set or Manual Channel Set (Z pg. 13 or 14).

Language Setting

This VCR offers you the language choice to view menus and some messages (excluding the on-screen display superimposed on the TV screen) — in English, Spanish or French. Select the desired language using the following procedure. The default setting is “ENGLISH”.

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

1 4

123 456

2 3

Access Main Menu screen

Press MENU.

Access Initial Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “INITIAL SET”, then press OK or SHUTTLE

PLUS

Select language

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “LANGUAGE”, then press OK or SHUTTLE

repeatedly until

PLUS the desired language is selected.

Return to normal screen

Press MENU.

MAIN MENU

FUNCTION SET TUNER SET

INITIAL SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

INITIAL SET

CLOCK SET

LANGUAGE ENGLISH

GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET

SELECT WITH (5,∞) AND (OK) PRESS (MENU) TO END

2 3

Clock Setting

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

1 8

123 456

2 – 7

INITIAL SETTINGS (cont.)

Perform clock setting only if the clock has not been set correctly by the Plug & Play setting or if you use a cable box. Access the Clock Set screen to perform the Semiauto or Manual Clock Set. Each procedure starts from step 4 after preparation steps below are finished. If you use a cable box, set the clock manually. (Z pg. 12)

Preparations

Access Main Menu screen

Press MENU.

Access Initial Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “INITIAL SET”, then press OK or SHUTTLE

PLUS

Select clock set

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “CLOCK SET”, then press OK or SHUTTLE

PLUS

MAIN MENU

FUNCTION SET TUNER SET

INITIAL SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

INITIAL SET

CLOCK SET

LANGUAGE ENGLISH GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET

SELECT WITH (5,∞) AND (OK) PRESS (MENU) TO END

2 – 7

● “CABLE BOX USERS SET CLOCK MANUALLY” appears on the screen for about 5 seconds, then the Clock Set screen appears.

Setting clock semiautomatically

— Semiauto Clock Set

You can change the host channel/D.S.T. /time zone setting manually. First follow steps 1 to 3 on page 10, then go to the following steps.

Set Auto Clock to ON

Press SHUTTLE PLUS to move the highlight bar to “AUTO CLOCK”, then press SHUTTLE PLUS %ﬁ so that “ON” is selected. Then; To select the host channel — go to step 5. To select the D.S.T. mode — go to step 6. To select the time zone — go to step 7.

NOTE:

The time set previously will be erased when “AUTO CLOCK”, “HOST CH”, “D.S.T.” or “TIME ZONE” setting is changed.

Select host channel

You can either select “AUTO” or enter a PBS channel number. Press SHUTTLE PLUS # to move the highlight bar to “HOST CH”, then press SHUTTLE PLUS %ﬁ until “AUTO” or the desired PBS channel number is selected.

NOTE:

Some PBS channels do not transmit clock setting data.

TIME DATE YEAR

1:00PM 12/24 00 SUN

AUTO CLOCK : ON

HOST CH : AUTO (CATV) D.S.T. : AUTO TIME ZONE : AUTO PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

CLOCK SET

Select D.S.T. mode

You have three choices: AUTO– Select if you want to adjust your VCR’s

clock automatically by the incoming signal from the host channel. (Auto Daylight Saving Time*)

ON– Adjustment will be made by the built-in

clock itself.

OFF– Select when Daylight Saving Time does

not apply to you.

Press SHUTTLE PLUS to “D.S.T.”, then press SHUTTLE PLUS %ﬁ repeatedly until the desired setting is selected.

to move the highlight bar

Select time zone

You can select the time zone automatically or manually.

Press SHUTTLE PLUS to “TIME ZONE”, press SHUTTLE PLUS %ﬁ repeatedly until “AUTO” or the desired time zone is selected. Each time you press the button, the time zone changes as follows:

= AUTO = ATLANTIC = EASTERN = CENTRAL = MOUNTAIN = PACIFIC = ALASKA = HAWAII = (back to the beginning)

to move the highlight bar

NOTE:

If an incorrect clock time is displayed by the Plug & Play setting, you may be receiving the clock setting data of a PBS channel from an adjacent time zone or from an incorrect PBS channel from a cable TV system. If you selected "AUTO" for the host channel in step 5, be sure to select the correct time zone manually.

* Auto Daylight Saving Time

This function enables automatic adjustment of the VCR’s clock at the start and end of Daylight Saving Time. With Auto DST activated, . . . . . . on the first Sunday of April at 2:00 AM, the clock is adjusted to 3:00 AM. . . . on the last Sunday of October at 2:00 AM, the clock is adjusted to 1:00 AM.

Return to normal screen

Press MENU.

IMPORTANT

Turn off the VCR after performing Semiauto Clock Set. ”Auto” will appear on the front display panel while the clock is being set. The current clock time will appear automatically when the clock setting is complete.

INITIAL SETTINGS (cont.)

Set date

Press SHUTTLE PLUS %ﬁ until the desired date appears, then press OK or SHUTTLE PLUS

● Holding SHUTTLE PLUS %ﬁ changes the date

in 15-day intervals.

123 456

Set year

Press SHUTTLE PLUS %ﬁ until the desired year appears, then press OK or SHUTTLE PLUS

Select D.S.T. mode

You can select either “ON” or “OFF”. ON– Adjustment will be made by the built-in

clock itself.

OFF– Select when Daylight Saving Time does

not apply to you.

Press SHUTTLE PLUS %ﬁ to select the desired setting.

twice.

Start clock

4 – 7

Press MENU and normal screen appears.

To make corrections any time during the process

Press OK or SHUTTLE PLUS # repeatedly until the item you want to change blinks, then press SHUTTLE PLUS %ﬁ.

4 – 7

Setting clock manually

— Manual Clock Set

First follow steps 1 to 3 on page 10, then go to the following steps.

Set time

Press SHUTTLE PLUS %ﬁ until the desired time appears, then press OK or SHUTTLE PLUS

● Holding SHUTTLE PLUS %ﬁ changes the time

in 30-minute intervals.

● When the time is entered manually, “AUTO CLOCK” is automatically set to “OFF”, and “HOST CH” and “TIME ZONE” disappear.

CLOCK SET

TIME DATE YEAR

– –:– –AM 1/ 1 00

AUTO CLOCK : ON HOST CH : AUTO (CATV) D.S.T. : AUTO TIME ZONE : AUTO PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

Tuner Setting

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

1 4

123 456

2 3

Setting channels automatically — Auto Channel Set

Use Auto Channel Set only if channels have not been set correctly by the Plug & Play setting. If you want to add or delete channels, use Manual Channel Set (Z pg. 14).

Access Main Menu screen

Press MENU.

Access Tuner Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “TUNER SET”, then press OK or SHUTTLE

PLUS

Perform Auto Channel Set

You can automatically set the receivable channels in your area in the order of their frequencies. Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “AUTO CHANNEL SET”, then press OK or SHUTTLE PLUS

MAIN MENU

FUNCTION SET

TUNER SET

INITIAL SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

TUNER SET

BAND CATV

AUTO CHANNEL SET

MANUAL CHANNEL SET

SELECT WITH (5,∞) AND (OK) PRESS (MENU) TO END

AUTO CHANNEL SET

SCANNING...

2 3

PRESS (MENU) TO END

NOTES:

●

When Auto Channel Set is complete, “SCAN COMPLETED” appears on screen.

●

If the scan was unsuccessful, “SCAN COMPLETED– NO SIGNAL” appears on screen. Check the connections and start again.

Return to normal screen

Press MENU.

INFORMATION

The VCR selects the correct band (TV or CATV) automatically during Auto Channel Set. The selected band will be displayed on the right side of “BAND” on the Tuner Set screen.

1 5

123 456

2 – 4

INITIAL SETTINGS (cont.)

Access Tuner Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “TUNER SET”, then press OK or SHUTTLE PLUS #.

Access Manual Channel Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “MANUAL CHANNEL SET”, then press OK or

SHUTTLE PLUS

Add or skip desired channels

To add channels

1 Press the Number

keys to input a channel number you want to add.

2 Press OK or

SHUTTLE PLUS set to “ADD”.

3 Repeat 1 and 2 to

add other channels.

To skip channels

1 Press the Number keys or SHUTTLE PLUS %ﬁ

to input a channel number you want to skip.

2 Press OK or SHUTTLE PLUS 3 Repeat 1 and 2 to skip other channels.

BAND CATV AUTO CHANNEL SET

MANUAL CHANNEL SET

SELECT WITH (5,∞) AND (OK) PRESS (MENU) TO END

MANUAL CHANNEL SET

PRESS NUMBER KEY (0–9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

TUNER SET

(CATV)

CH 45 ADD

to set to “SKIP”.

Setting channels manually

— Manual Channel Set

You can add the channels you want or delete the channels you do not want manually.

Access Main Menu screen

Press MENU.

Return to normal screen

Press MENU.

Cable Box Control Setting

The following procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer recording. The Controller is effective for recording broadcasts that have been programmed using VCR Plus+ system (Z pg. 30) or Express timer programing (Z pg. 34).

Suggested location

Place the cable box on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

ATTENTION:

The Controller can also control a DBS receiver. If both a cable box and a DBS receiver are used, position the Controller so its signal reaches the remote sensors on both the cable box and DBS receiver.

Your VCR

Cable box

Controller (suggested locations)

Installing Controller

Situate Controller

Place the Controller so that its transmitter is facing the cable box’s remote sensor.

● Make sure the path between the Controller and the cable box’s remote sensor is not blocked.

Attach Controller

Fix securely using the adhesive strip attached on the back of the Controller.

Connect cable box to VCR

●

If your cable box does not have audio/video output connectors

Connect the RF output terminal on the cable box to the ANTENNA IN terminal on the rear of your VCR.

If your cable box has audio/video output

●

connectors

Connect an audio/video cable between the AUDIO/VIDEO IN connectors on the rear of the VCR and the audio/video output connectors on the cable box.

NOTE:

When connecting your cable box, refer to its instruction manual.

Controller

Your VCR

RF output

Transmitter

ANTENNA

CABLE

BOX

To Audio/Video output

To AUDIO/ VIDEO IN

Connect Controller to VCR

Connect the Controller to the CABLE BOX Controller connector on the rear panel.

How to control the cable box

This VCR has two separate methods to control your cable box.

● The VCR’s wireless Remote can control your cable box. This eliminates the need for a separate cable box’s Remote.

● The VCR’s Controller can also control your cable box. This allows the VCR to change your cable box’s channel number during timer recording.

Each method must be set up separately. To set up the VCR’s Remote, refer to page 53. To set up the Controller, go to page 16.

INITIAL SETTINGS (cont.)

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

123 456

3 4 6 7

3 – 5

Setting cable box output channel & brand

After installation, set the cable box output’s channel and its brand correctly; otherwise, the Controller cannot work correctly.

Access Main Menu screen on VCR

Press MENU.

Access Initial Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “INITIAL SET”, then press OK or SHUTTLE PLUS #.

Access Cable Box Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “CABLE BOX SET”, then press OK or

SHUTTLE PLUS

CLOCK SET LANGUAGE ENGLISH GUIDE CHANNEL SET

CABLE BOX SET

DBS RECEIVER SET

SELECT WITH (5,∞) AND (OK) PRESS (MENU) TO END

Select cable box output channel

Your selection depends on how your cable box is connected to your VCR.

● If your cable box is connected to your VCR’s ANTENNA IN terminal on the rear

Press SHUTTLE PLUS %ﬁ on the Remote until the channel number representing the cable box’s output (CH2 – CH9) appears on the screen.

● If your cable box is connected to your VCR’s AUDIO/VIDEO IN connectors on the front panel

Press SHUTTLE PLUS %ﬁ on the Remote until “ON F-1 (FRONT)” appears on the screen.

● If your cable box is connected to your VCR’s AUDIO/VIDEO IN connectors on the rear panel

Press SHUTTLE PLUS %ﬁ on the Remote until “ON L-1 (REAR)” appears on the screen.

● If you do not use a cable box

Press SHUTTLE PLUS %ﬁ on the Remote until “OFF” appears on the screen.

CABLE BOX SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

INITIAL SET

OFF

Turn on cable box

Select a channel other than channel 9 on your cable box.

Access Cable Box Brand Set screen

Press OK.

Enter cable box brand

Press the appropriate Number keys to enter the brand code from the list shown to the right, then press OK.

● If the cable box’s channel changes to 9, setting is complete

Press OK and “CABLE BOX CONTROL IS ON” appears on the screen for about 5 seconds, then it returns to the normal screen.

● If the cable box's channel does not change to 9

1 Press SHUTTLE PLUS %ﬁ to move the

highlight bar (arrow) to “NO”.

2 Press OK. 3 Repeat step 7 until the cable box’s channel

changes to 9 by entering another code.

4 If the channel does not change after going

through all the code numbers listed for your model of cable box, then try all the other numbers between 1 and 25.

CABLE BOX BRAND SET

PRESS NUMBER KEY (0–9)

THEN (OK) TO TEST

PRESS (MENU) TO END

CABLE BOX BRAND SET

DID YOUR CABLE BOX CHANGE TO CHANNEL 09? = YES NO

PRESS (5,∞), THEN (OK)

PRESS (MENU) TO END

CABLE BOX BRAND LIST

BRAND CODE

ARCHER 1, 5, 17 CABLETENNA 1, 17 CABLEVIEW 15, 16, 17, 21, 25 CITIZEN 15, 16, 17, 21, 25

CURTIS 2, 8 DIAMOND 1, 17 EASTERN 19 GC BRAND 15, 16, 17, 21, 25 GEMINI 15 GENERAL INSTRUMENTS 1, 4, 6, 11, 12, 15, 28 HAMLIN 10, 18, 19, 23 JASCO 15 JERROLD 1, 4, 6, 11, 12, 15, 28 NOVAVISION 2, 8 OAK 7, 20 PANASONIC 13, 14 PULSER 15, 16, 17, 21, 25 RCA 13, 14 REGAL 10, 18, 19, 23 REGENCY 19 REMBRANDT 1, 16, 17 SAMSUNG 5, 16, 24 SCIENTIFIC ATLANTA 2, 8 SIGMA 7, 20 SL MARX 5, 16, 17, 24, 25 SPRUCER 13, 14 STARGATE 5, 15, 16, 17, 21, 24, 25 TELEVIEW 5, 16, 24 TOCOM 1, 4, 16 UNIKA 1, 17 UNIVERSAL 16, 17, 25 VIDEOWAY 3, 9, 22 ZENITH 3, 9, 22

If the VCR’s clock has not been set (with AUTO CLOCK set to ON)

“CABLE BOX USERS SET CLOCK MANUALLY” appears for about 5 seconds when you press OK in step 6, then the Clock Set screen appears. Perform Manual Clock Set on page 12. If you press MENU after the clock has been set, the Cable Box Brand Set screen appears.

NOTES:

●

The Controller may not work with all types of cable box.

●

If your cable box does not respond to any code between 1 and 25, you cannot use the Controller to change cable box channels. In this case, make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start time of timer recording. Contact your cable company about the possibility of exchanging your current cable box with the one compatible with your VCR.

●

The VCR can only change the cable box channel through the Controller during timer recording.

●

If your cable box cannot be operated with a remote control (because it has no remote sensor), you cannot use the Controller to change its channels. Make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start time of timer recording.

●

If the VCR’s memory backup expires because of a power failure, set the cable box output channel and brand again.

●

For customers in U.S.A.: If you are unable to set the Controller, contact JVC toll free at 1-800-537-5722.

DBS Receiver Control Setting

Suggested location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver’s remote sensor.

ATTENTION:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the Controller so its signal reaches the remote sensors on both the DBS receiver and cable box.

DBS receiver

INITIAL SETTINGS (cont.)

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) receiver. The Controller allows the VCR to automatically switch the DBS receiver’s channels during timer recording.

NOTES:

●

The VCR can automatically change the DBS receiver channels using the Controller when the VCR has been programed using Express timer programing (Z pg. 34) Because satellite programing does not use PlusCode, the Controller cannot change the DBS receiver channels during VCR Plus+ timer recording.

●

If a cable box is also used, it is recommended that you connect the DBS receiver to your VCR’s audio/video input connectors and the cable box to your VCR’s antenna input terminal.

Installing Controller

Situate Controller

Place the Controller so that its transmitter is facing the DBS receiver’s remote sensor.

● Make sure the path between the Controller and the DBS receiver’s remote sensor is not blocked.

Your VCR

Controller

Your VCR

DBS receiver

RF output

Transmitter

ANTENNA IN

CABLE

BOX

To AUDIO/ VIDEO IN

Controller (suggested locations)

To Audio/Video output

Attach Controller

Fix securely using the adhesive strip attached on the back of the Controller.

Connect DBS receiver to VCR

●

If your DBS receiver does not have audio/ video output connectors

Connect the RF output terminal on the DBS receiver to the ANTENNA IN terminal on the rear of your VCR.

If your DBS receiver has audio/video output

●

connectors

Connect an audio/video cable between the AUDIO/VIDEO IN connectors on the rear of the VCR and the audio/video output connectors on the DBS receiver.

NOTE:

When connecting your DBS receiver, refer to its instruction manual.

Connect Controller to VCR

Connect the Controller to the CABLE BOX Controller connector on the rear panel.

How to control the DBS receiver

This VCR has two separate methods to control your DBS receiver.

● The VCR’s wireless Remote can control your DBS receiver. This eliminates the need for a separate DBS receiver’s Remote.

● The VCR’s Controller can also control your DBS receiver. This allows the VCR to change your DBS receiver’s channel number

during timer-recording.

Each method must be set up separately. To set up the VCR’s Remote, refer to page 54. To set up the Controller, go to page 19.

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

123 456

3 4

3 – 5

Setting DBS receiver output channel & brand

After installation, set the DBS receiver’s output channel and its brand correctly; otherwise, the Controller cannot work correctly.

Turn on DBS receiver

Select a channel other than channel 55, 100 or 205 on your DBS receiver.

Access Main Menu screen on VCR

Press MENU.

Access Initial Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “INITIAL SET”, then press OK or SHUTTLE PLUS #.

Access DBS Receiver Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “DBS RECEIVER SET”, then press OK or

SHUTTLE PLUS

CLOCK SET LANGUAGE ENGLISH GUIDE CHANNEL SET CABLE BOX SET

DBS RECEIVER SET

SELECT WITH (5,∞) AND (OK) PRESS (MENU) TO END

Select DBS receiver output channel

Your selection depends on how your DBS receiver is connected to your VCR.

● If your DBS receiver is connected to your VCR’s ANTENNA IN terminal on the rear

Press SHUTTLE PLUS %ﬁ on the Remote until the channel number representing the DBS receiver’s output (CH3 or CH4) appears on the screen.

● If your DBS receiver is connected to your VCR’s AUDIO/VIDEO IN connectors on the front panel

Press SHUTTLE PLUS %ﬁ on the Remote until “ON F-1 (FRONT)” appears on the screen.

● If your DBS receiver is connected to your VCR’s AUDIO/VIDEO IN connectors on the rear panel

Press SHUTTLE PLUS %ﬁ on the Remote until “ON L-1 (REAR)” appears on the screen.

● If you do not use a DBS receiver

Press SHUTTLE PLUS %ﬁ on the Remote until “OFF” appears on the screen.

CONTINUED ON NEXT PAGE \

DBS RECEIVER SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

INITIAL SET

OFF

123 456

INITIAL SETTINGS (cont.)

Access DBS Receiver Brand Set screen

Press OK.

Enter DBS Receiver’s brand

Press the appropriate Number keys to enter the brand code from the

following list, then press OK. The program currently received through the

DBS receiver appears for about 10 seconds.

BRAND CODE

JVC (DISH Network) 51 ECHOSTAR (DISH Network) 51 PRIMESTAR 50 SONY (DSS) 41 RCA (DSS) 40

DBS RECEIVER BRAND SET

4 0

PRESS NUMBER KEY (0–9)

THEN (OK) TO TEST

PRESS (MENU) TO END

6 7

● If the DBS receiver’s channel changes to the channel listed below for your brand, setting is complete

JVC = 100 ECHOSTAR = 100 PRIMESTAR = 55 SONY = 205 RCA = 205

Press OK and “DBS RECEIVER CONTROL IS ON” appears on the screen for about 5 seconds, then it returns to the normal screen.

DBS RECEIVER BRAND SET

DID YOUR DBS RECEIVER CHANGE TO CHANNEL 100? = YES NO

PRESS (5,∞), THEN (OK)

PRESS (MENU) TO END

● If the DBS receiver’s channel does not change as shown above

1 Press SHUTTLE PLUS %ﬁ to move the

highlight bar (arrow) to “NO”.

2 Press OK. 3 Re-enter the correct code.

NOTES:

●

The Controller may not work with all types of DBS receiver.

●

If your DBS receiver does not respond to the code, you cannot use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording.

●

The VCR can only change the satellite channel through the Controller during timer recording.

●

If your DBS receiver cannot be operated with a remote control (because it has no remote sensor), you cannot use the Controller to change its channels. Make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording.

●

For customers in U.S.A.: If you are unable to set the Controller, contact JVC toll free at 1-800-537-5722.

BASIC PLAYBACK AND RECORDING

Basic Playback

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

JOG dial

POWER

S VIDEO

VIDEO (MONO)L—AUDIO—R

REW ( 1 )

REC LINK

DIGITAL TBC/NR

SP EP

VCR

123 456

PLAY

A.DUB

24HR QUICK PROGRAM

INSERT

STOP/EJECT

REW

–

REC PAUSE STOP/EJECT

( 7 / 0 )

POWER

FF ( ¡ )

STOP ( 7 )

This VCR can check the tape condition during playback (and recording), and realizes the best possible pictures.

Load a cassette

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Do not apply too much pressure when inserting.

● The VCR turns on automatically.

● The counter is automatically reset to “0:00:00”.

● If the cassette’s record safety tab has been

removed, playback begins automatically.

Start playback

CH– /+

PUSH / TURN

Press PLAY ( 3 ).

● Tape speed (SP or EP) is automatically detected.

● The S-VHS indicator lights up on the front

display panel when you play back a tape recorded in S-VHS mode or in S-VHS ET mode (Z pg. 43)

● If “VIDEO CALIBRATION” is set to “ON” (default setting: Z pg. 40), “VIDEO CALIBRATION” appears on the screen, and this VCR checks the tape condition during automatic tracking.

● If the tape ends during playback or fast-forward search, the cassette indication “

” blinks for a few seconds and the VCR starts rewinding the tape automatically.

To stop playback

Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

To rewind the tape

Press REW ( 1 ) (or turn the JOG dial on the front panel to the left).

To fast-forward the tape

Press FF ( ¡ ) (or turn the JOG dial on the front panel to the right).

To eject the tape

Press STOP/EJECT ( 7 / 0 ) on the front panel when the tape is not running.

● You can also eject the cassette with the VCR turned off.

To turn off the VCR

Press POWER.

Clean the video heads using a dry cleaning cassette — TCL-2UX — when:

• Rough, poor picture appears while a tape is played back.

• The picture is unclear or no picture appears.

• “USE CLEANING CASSETTE” appears on the screen (only with “SUPERIMPOSE” set to “ON”: Z pg. 39,

40.)

Basic Playback

BASIC PLAYBACK AND RECORDING (cont.)

Changing display information

Press DISPLAY during playback.

Each time you press the button, the front display panel shows the time counter, tape remaining time and the clock time in sequence.

Features

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

123 456

C. RESET

–a, b, c

S VIDEO

–a

A.DUB

INSERT

REW

PLAY

–

24HR QUICK PROGRAM

REC PAUSE STOP/EJECT

STOP/EJECT

( 7 / 0 )

–b

–C

–2

–1

STOP ( 7 )

Time Counter

Tape Remaining Time

Clock Time

● To display the VCR status including the tape remaining

CH– /+

PUSH / TURN

time, the time counter and the clock time on the TV screen, see “Showing on-screen display” (Z pg. 27).

● The approximate tape remaining time appears and the " indicator lights on the front display panel.

● The tape remaining time is calculated based on the

tape speed (SP or EP) being used. The indicated remaining time is only an estimate.

To reset the time counter, press C. RESET on the Remote. The counter reading becomes “0:00:00”. It is also reset when a tape is inserted.

Checking tape position

The tape position indicator appears on screen in the following cases:

● When you change the VCR

operation mode from the stop mode to fast forward or rewind mode.

● When you perform an Index

Search (Z pg. 23) or Instant Review (Z pg. 24).

The position of “ (End) shows you where you are on the tape.

” in relation to “B” (Beginning) or “E”

+++

COUNT 0:33:27

NOTES:

●

"SUPERIMPOSE" must be set to “ON”, or the indicator will not appear (Z pg. 39, 40).

●

It may take a few seconds for the tape position indicator to be displayed.

Playing back tape repeatedly

— Repeat Play

You can play back a tape repeatedly (100 times).

While playing back a tape, press and hold PLAY ( 3 ) for more than 5 seconds.

The play indicator ( # ) on the front display panel starts flashing slowly, and a tape will be played back 100␣ times.

To stop playback, press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

Adjusting tracking condition

— Tracking Adjustments

Automatic tracking adjustment

This VCR automatically adjusts the tracking condition. Whenever you insert a tape and start playback, automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback.

Manual tracking adjustment

If automatic tracking cannot eliminate noises well during playback, use the manual tracking following the procedures below.

● You can also use the manual tracking during slow motion playback (Z pg. 29).

1 Activate manual tracking

Press SP/EP on the Remote during playback.

2 Eliminate the noises on the TV screen

Press CH + or – on the Remote.

● Press it briefly for a fine adjustment, or press and hold for coarse adjustment. Watch the screen and continue adjustment until optimum picture and sound quality are achieved.

● To reactivate automatic tracking, press SP/EP on the Remote. The automatic tracking becomes active again.

Selecting monitor sound

— Audio Monitor

You can select the desired monitor sound.

While playing back a tape on which stereo sound or SAP sound is recorded, press A. MONITOR on the Remote.

Each time you press the button, sound changes as follows:

HI-FI

HI-FI: Normally select this.

Hi-Fi sound is played back. HI-FI L: Sound on the left Hi-Fi channel is played back. HI-FI R: Sound on the right Hi-Fi channel is played back. NORM:Sound on the normal track is played back. NORM HI-FI:

Both sounds on the Hi-Fi track and normal

track are mixed and played back.

NOTES:

●

The above indication appears when “SUPERIMPOSE” is set to “ON” (Z pg. 39, 40), though the monitor sound changes in sequence.

●

If the tape being played back has no Hi-Fi sound track, the normal sound track will be heard regardless of this setting.

●

If RF connection (Z pg. 7) is used for viewing pictures on the TV, sound will be monaural even though you select “HI-FI”.

●

You can also use the menu to select your desired monitor sound. (Z pg. 42)

HI-FI L HI-FI R

NORM HI-FI

NORM

Automatic operations after

rewinding — Next Function Memory

The Next Function Memory “tells” the VCR what to do after rewinding is complete.

● Ensure that the VCR is in stop mode.

a– For Automatic Playback Start

Press REW ( 1 ), then press PLAY ( 3 ) within 2␣ seconds.

b– For Automatic Power Off

Press REW ( 1 ), then press POWER within 2␣ seconds.

c– For Automatic Timer Standby

Press REW ( 1 ), then press TIMER within 2␣ seconds.

NOTE:

It is not possible to select the Automatic Timer Standby function if the cassette’s record safety tab is removed.

Locating beginning of

recordings — Index Search

Index codes are placed on the tape at the beginning of each recording when recording on this VCR. You can find and automatically play back from the beginning of any recording using the Index Search function.

1 Start search

While the tape is not running, press SHUTTLE PLUS 4 or ¢ on the Remote.

2 Access distant code

To access a recording of 2 to 9 index codes away, press SHUTTLE PLUS 4 or ¢ repeatedly until the correct number is displayed on screen (only if “SUPERIMPOSE” is set to “ON” ; Z pg. 39, 40). Playback begins automatically when the desired recording is located.

Beginning of the current program recorded

Previous program recorded

–1

● If you want to find the very beginning of the

desired program, press REW ( 1 ) or FF ( ¡ ) after playback starts.

Current position on the tape

Next program recorded

NOTE:

An index code is not placed on the tape when recording is resumed from recording pause.

Beginning of the 2nd next program recorded

2nd next

2–23

BASIC PLAYBACK AND RECORDING (cont.)

Locating beginning of timer

recordings — Instant Review

REW

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

S VIDEO

PLAY

–

A.DUB

24HR QUICK PROGRAM

INSERT

REC PAUSE STOP/EJECT

123 456

REW ( 1 )

Other Useful functions for playback

● Video Calibration (Z pg. 40)

When this function is set to “ON”, this VCR checks the condition of the tape in use during playback and recording, and compensates to provide the highestpossible pictures.

FF ( ¡ )

CH– /+

PUSH / TURN

At the press of a button, you can turn on the VCR, rewind the tape and begin to view the most recent timerrecorded program.

After ensuring that the VCR is turned off and that the timer mode is disengaged, press REVIEW.

● The VCR turns on, and rewinds to the index code indicating the beginning of the last timer-recorded program, then begins playback automatically.

● You can access a program of 2 to 9 index codes away from the current position on the tape. If, for example, you have 5 programs recorded and you want to watch the third one, press REVIEW three times.

● If you want to find the very beginning of the desired program, press REW ( 1 ) or FF ( ¡ ) after playback starts.

● If the tape is already rewound when REVIEW is pressed, it will play the tape from the beginning. It will not fast-forward to an index code.

● The Instant Review function will also operate if the VCR is turned on.

Adjusting picture condition

— Digital TBC/NR

The Digital TBC/NR (Time Base Corrector / Noise Reduction) function removes jitter from fluctuating video signals to deliver a stable picture even with old tapes and rental tapes. The Digital 3-DNR (Noise Reduction) function which cuts noise and reproduces clear pictures is also linked to this function. We recommend that you use the Digital TBC/NR function when... — playing back a tape recorded on a camcorder. — playing back a tape repeatedly used. — using this VCR as the player for editing.

Press DIGITAL TBC/NR on the front panel so that the DIGITAL TBC/NR lamp lights up.

Each time you press the button, this function turns on and off.

● Picture Control (Z pg. 40)

This function helps you to adjust the playback picture quality according to your preference.

● Video Stabilizer (Z pg. 41)

You can automatically correct vertical vibrations in the picture when playing back unstable recordings made on another VCR.

● Blue Back (Z pg. 41)

When this function is set to “ON”, the TV screen becomes all blue in the following cases: – When receiving a channel not in use. – When stopping playback.

NOTES:

●

If you play back a tape recorded under poor TV reception condition, the picture may happen to become more stable with Digital TBC/NR activated.

●

If you play back a tape on which certain types of signals (using a PC or some character generators) have been recorded with Digital TBC/NR activated, the playback picture may be distorted. In this case, deactivate Digital TBC/NR.

●

Digital TBC/NR and Video Stabilizer (Z pg. 41) cannot be used at the same time; if you turn on Digital TBC/NR when “VIDEO STABILIZER” is set to “ON”, Video Stabilizer will be automatically turned “OFF”. Make sure Digital TBC/NR is deactivated when you want to use Video Stabilizer.

Basic Recording

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

JOG dial

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

123 456 7

S VIDEO

TV/VCR

This VCR can check the tape condition during recording (and playback), and realizes the best possible pictures.

Load a cassette

Make sure the record safety tab is intact. If not, cover the hole with adhesive tape before inserting the cassette.

PLAY ( 3 )

SP EP

VCR

89 0

REW

PLAY

–

A.DUB

24HR QUICK PROGRAM

INSERT

PAUSE ( 8 )

STOP/EJECT

( 7 / 0 )

POWER

2 –b

FF ( ¡ )REW ( 1 )

PAUSE ( 8 )

STOP ( 7 )

REC PAUSE STOP/EJECT

–a

CH– /+

PUSH / TURN

Select recording channel

On the front panel: Push the JOG dial, then turn it to the left or right.

On the Remote: a– Press CH + or –.

b– Press the Number keys.

● If you connect the TV and the VCR only using

the RF connection, press TV/VCR on the Remote so that the VCR mode indicator lights on the front display panel, to view the program to be recorded.

Set tape speed

Press SP/EP to set the recording speed.

Start recording

On the front panel: Press REC ( ¶ ).

On the Remote: While holding REC ( ¶ ), press PLAY ( 3 ).

● If “VIDEO CALIBRATION” is set to “ON” (default setting: Z pg. 40), this VCR checks the tape condition for about seven seconds, then starts recording. This means that the first seven seconds of the program will not be recorded. If this is inconvenient for you, follow the steps below:

1 Press REC ( ¶ ) and PAUSE ( 8 ) to start

Video Calibration.

2 Then press PLAY ( 3 ) to start recording

after Video Calibration is complete.

To pause recording

Press PAUSE ( 8 ). To resume recording, press PLAY ( 3 ).

To stop recording

Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

To rewind the tape (when it is not running)

Press REW ( 1 ) (or turn the JOG dial on the front panel to the left).

To fast-forward the tape (when it is not running)

Press FF ( ¡ ) (or turn the JOG dial on the front panel to the right).

To eject the tape

Press STOP/EJECT ( 7 / 0 ) on the front panel when the tape is not running.

● You can also eject the cassette with the VCR turned off.

To turn off the VCR

Press POWER.

It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.

Basic Recording

BASIC PLAYBACK AND RECORDING (cont.)

Changing display information

Press DISPLAY during recording or recording pause.

Each time you press the button, the front display panel shows the time counter, tape remaining time, channel number and the clock time in sequence.

Features

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

123 456

S VIDEO

C –1

C. RESET

STOP/EJECT ( 7 / 0 )

REW

PLAY

A.DUB

24HR QUICK

PROGRAM

INSERT

–

REC PAUSE STOP/EJECT

CH– /+

PUSH / TURN

Time Counter

Clock Time

● To display the VCR status including the tape remaining time, the time counter and the clock time on the TV screen, see “Showing on-screen display” (Z pg. 27).

● The approximate tape remaining time appears and the

" indicator lights on the front display panel.

● The tape remaining time is calculated based on the tape speed (SP or EP) being used. The indicated remaining time is only an estimate.

To reset the time counter, press C. RESET on the Remote. The counter reading becomes “0:00:00”. It is also reset when a tape is inserted.

Specifying recording length

Tape Remaining Time

Channel No.

— Instant Timer Recording (ITR)

You can easily specify the recording length from 30␣ minutes to 6 hours and the VCR shuts off after recording is finished.

During recording, press REC ( ¶ ) on the front panel repeatedly until the recording length you want appears on the front display panel.

(record) indicator starts blinking.

The Each time you press the button, recording length increases in 30-minute intervals (up to 6 hours).

To cancel an ITR, press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

Accidental erasure prevention

To prevent accidental recording on a recorded cassette, remove its record safety tab. To record on it later, cover the hole with adhesive tape.

STOP ( 7 )

Record safety tab

Watching one program while

recording another

1 Engage TV mode

During recording...

● If you connect the TV and the VCR only using the RF connection (Z pg. 7) to view pictures from the VCR

Press TV/VCR on the Remote so that VCR mode indicator goes off from the front display panel. (The TV broadcast being recorded disappears.)

● If you are using the AV connection (Z pg. 7) to view pictures from the VCR, change the TV’s

input mode from AV to TV.

2 Select channel for viewing

Select the channel, you want to watch, on the TV.

Showing on-screen display

When “SUPERIMPOSE” is set to “ON” (Z pg. 39, 40), you can see the current VCR status on the TV screen.

● For more detailed information about the on-screen display, see page 63.

1 Display VCR status on TV screen

During recording or recording pause, press OSD. All indications corresponding to the current VCR status are displayed for 5 seconds. The time counter remains on the screen indicating the elapsed time.

● The indications are not recorded.

CH 125 RECORD THU 12:00 AM PAUSE STEREO ] SP SAP

+++

NORM REMAIN 10:00 HI–FI COUNT –1:23:45

INDEX 1

2 Exit on-screen display

Press OSD again.

NOTES:

●

If the VCR is in recording pause mode, “RECORD/PAUSE” is always displayed.

●

The VCR status can be also displayed during playback.

Other useful functions for recording

● Recording Resume Function

If there is a power outage during recording (or Instant Timer Recording, or timer recording), the recording will resume automatically when the power is restored to the VCR. (No setting is required for this function.)

● Video Calibration (Z pg. 40)

When this function is set to “ON”, this VCR checks the condition of the tape in use during playback and recording, and compensates to provide the highestpossible pictures.

● Second Audio Recording (Z pg. 41)

This VCR’s built-in MTS decoder enables reception of Multichannel TV Sound broadcast.

To record a SAP program received, set “2ND AUDIO RECORD” to “ON” using the menu screen.

NOTES:

When the channel is changed on the VCR;

●

The “STEREO” indication appears on the screen for about 5 seconds if the program is a stereo broadcast.

●

The “SAP” indication appears on the screen for about 5␣ seconds if the program is a SAP broadcast.

●

Both indications appear when a stereo program is accompanied by SAP sound.

● S-VHS Recording Mode (Z pg. 42)

This VCR allows you to record on an S-VHS tape with VHS picture quality.

● S-VHS ET (Z pg. 43)

This function allows you to record on VHS tapes with SVHS picture quality. Tapes recorded using this function can be played back on a VCR equipped with the S-VHS ET function.

Special Effect Playback

PLAY ( 3 )

REW

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

S VIDEO

PLAY

–

A.DUB

24HR QUICK

PROGRAM

INSERT

REC PAUSE STOP/EJECT

SPECIAL EFFECT PLAYBACK

Locating particular scene

rapidly — Picture Search

7 High-Speed Picture Search:

You can rapidly locate a particular scene on the tape.

On the front panel:

EDB

CH– /+

PUSH / TURN

Possible during normal playback. To do forward picture search, turn the JOG dial quickly to the right. To do reverse picture search, turn the JOG dial quickly to the left.

● If you release the dial, picture search continues.

On the Remote:

Possible during normal playback or still picture playback.

To do forward picture search, press FF ( To do reverse picture search, press REW (

● If you press and hold the button for more than 2␣ seconds, simply releasing it cancels the picture search, and normal playback resumes.

To resume normal playback, press PLAY ( 3 ).

PLAY ( 3 )

123 456

7 Variable-Speed Picture Search:

Possible during normal playback. You can change the speed of picture search.

How to use the JOG dial on the front panel: Turn the JOG dial to the right (forward search) or to the

left (reverse search). Each time the JOG dial passes a click position, picture search speed changes (see the diagram below). If you release the dial, picture search continues.

● The speed of picture search is determined by the

number of click stops of the JOG dial.

A B

A E

)

(

)

(

)

How to use the SHUTTLE PLUS buttons on the Remote: To do forward picture search, press SHUTTLE PLUS

¢ repeatedly. Each time you press the button, the search speed increases.

● To decrease the speed while forward picture search (toward normal playback, then reverse picture search), press SHUTTLE PLUS 4 repeatedly.

To do reverse picture search, press SHUTTLE PLUS 4 repeatedly. Each time you press the button, the search speed increases while reverse picture search.

● To decrease the speed while reverse picture search (toward normal playback, then forward picture search), press SHUTTLE PLUS ¢ repeatedly.

To resume normal playback, press PLAY ( 3 ).

SHUTTLE

Reverse

4 steps 2 steps 2 steps 5 steps

Reverse

play

Viewing still picture

–

Reverse

slow motion

PLUS

–

Slow

motion

Normal

Play

Forward

— Still Picture Playback

On the front panel: Push the JOG dial during normal playback.

On the front panel or the Remote:

Press PAUSE ( 8 ) during normal playback. Playback is freezed and a still picture appears.

To resume normal playback, press PLAY ( 3 ).

NOTE:

To obtain a noiseless still picture, it may be necessary to adjust tracking in slow motion playback before starting still picture playback.

Skipping unwanted portions

— Skip Search

You can skip over (view at high speed) unwanted portions of the tape.

Press SKIP SEARCH once to 4 times during playback.

Each press initiates a 30-second period of high speed playback (up to 2 minutes). When the specified portion of the tape is skipped, normal playback resumes automatically.

To return to normal playback during Skip Search, press PLAY ( 3 ).

Viewing still picture frame by

frame

— Frame-by-Frame Playback

On the front panel: During normal playback: Push the JOG dial or press PAUSE ( 8 ) to pause. To advance a still picture, turn the JOG dial to the right. To reverse a still picture, turn the JOG dial to the left.

On the Remote: During normal playback: Press PAUSE ( 8 ) to pause. To advance a still picture, press SHUTTLE PLUS ¢ (or PAUSE ( 8 )) repeatedly. To reverse a still picture, press SHUTTLE PLUS 4

repeatedly. To resume normal playback, press PLAY ( 3 ).

Viewing slow motion picture

— Slow Motion Playback

On the front panel: During normal playback:

Turn the JOG dial to the first or second click-stop to the left (forward slow motion) or to the third or fourth clickstop to the left (reverse slow motion) so that slow motion playback starts. If you release the dial, slow motion playback continues.

● Holding PAUSE ( 8 ) for more than 2␣ seconds also

starts forward slow motion playback.

On the Remote:

● During normal playback:

Press SHUTTLE PLUS 4 to decrease the playback speed. Each time you press the button, the speed decreases (toward reverse slow motion playback, then reverse picture search).

● Holding PAUSE ( 8 ) for more than 2␣ seconds also

starts forward slow motion playback.

To resume normal playback, press PLAY ( 3 ).

● During still picture playback:

Press and hold SHUTTLE PLUS ¢ to start forward (or SHUTTLE PLUS 4 to start reverse) slow motion

playback. When you release the button, slow motion playback stops and a still picture appears.

● Holding PAUSE ( 8 ) for more than 2␣ seconds also

starts forward slow motion playback.

To resume normal playback, press PLAY ( 3 ).

NOTE:

Manual tracking is possible during slow motion playback. During slow motion playback, simply press Remote to adjust tracking.

CH +

or – on the

TIMER RECORDING

VCR Plus+ Timer Programing

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

POWER

DAILY

CANCEL

STOP +/–

2 7

123 456

3 4

WEEKLY

Timer recording allows you to program the VCR to automatically record a broadcast at some future time. Up to 8␣ timer recording programs can be made using VCR Plus+ timer programing, Express timer programing (Z pg. 34) or 24HR quick programing method (Z␣ pg.␣ 36) as far as a year in advance. The VCR Plus+ timer programing system eliminates the need to input channel, date, start and stop time data when programing timer recording settings. Simply key in the PlusCode number for the TV broadcast you wish to record and the VCR’s timer will be automatically programed. (The PlusCode programing numbers are the numbers next to the program in most TV listing.)

Load a cassette

Make sure the record safety tab is intact. If not, cover the hole with adhesive tape, then load it into the VCR.

● The VCR turns on, and the counter is reset, automatically.

Access PlusCode No. screen

Press PROG. on the Remote.

● The clock must be set to access the PlusCode No. screen. If you have not set the clock, the Main Menu screen appears after an error message is displayed. Refer to page 8 for the Plug & Play setting or page 10 for the clock setting procedure.

PLUSCODE NO.

PRESS NUMBER KEY (0–9) PRESS (+/–) TO SET

EXPRESS PROGRAMMING

PRESS (PROG.) TO END

Enter PlusCode number

Press the appropriate

3 4 7

Number keys to input the PlusCode number printed in the TV listings for the TV broadcast you wish to record, then press OK.

Then; If the Guide Channel Set screen appears

— go to step 4.

If the VCR Plus+ Program screen appears

— go to step 5.

● To make corrections, press CANCEL and input the correct PlusCode number.

PLUSCODE NO.

123

PRESS NUMBER KEY (0–9)

PRESS (PROG.) TO END

THEN (OK)

Input receiving channel number

The guide channel number, which is assigned to the TV or cable station for the PlusCode number that you entered in step 3, will appear automatically on the Guide Channel Set screen. Press the Number keys (or CH +/– or SHUTTLE PLUS %ﬁ) to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR or cable box, then press OK.

● The Guide Channel Set screen appears only when you input the PlusCode number of a station for which the guide channel number has not been set previously.

● If you receive your channels with a cable box and if you have properly set your Controller, “CABLE CH” appears in place of “VCR CH”. If not, refer to pages 15 – 17.

GUIDE CHANNEL SET

GUIDE CH: 12

VCR CH : –––

PRESS NUMBER KEY (0–9)

OR (5,∞), THEN (OK)

PRESS (PROG.) TO END

Check program date

The PlusCode number you entered and the corresponding timer recording program is displayed on the Program screen. Check to make sure it is accurate.

● To change the stop time, press STOP +/–.

● To timer-record daily (Monday–Friday) or

weekly serials, press DAILY (M-F) (number “8”) or WEEKLY (number “9”). “DAILY” or “WEEKLY” appears on the Program screen. Pressing the button again makes each corresponding display disappear.

● If you made a mistake, press CANCEL to access the PlusCode No. screen again and input the correct PlusCode number.

● If an incorrect PlusCode number or the one for a broadcast already finished has been inputted, “ERROR” is displayed for about 5 seconds, then the PlusCode No. screen reappears.

(PLUSCODE NO. 12345678)

START STOP 8:00PM = 10:00PM DATE CH

12/24/00 12 SP

SUN PRESS (8=DAILY, 9=WEEKLY STOP+/– = STOP TIME, SP/EP) PRESS (PROG.) TO END

Set tape speed

Press SP/EP .

PROGRAM 1

Return to normal screen

Press PROG. or OK. “PROGRAM COMPLETED” appears on the screen for about 5 seconds, then normal screen appears.

• If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking. You can now correct the conflicting programs. See “When programs overlap each other” on page 38.

Engage timer recording standby mode

Press TIMER . The VCR turns off automatically and “‰” is displayed on the front display panel.

To use the VCR while it is in timer recording standby mode

Press TIMER to cancel the timer recording standby mode, then press POWER to turn on the VCR. DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER after you use the VCR; otherwise, you cannot record the broadcasts you want.

● When “AUTO TIMER” (Z pg. 40) is set to “ON”, the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER to engage or disengage the timer recording standby mode.

IMPORTANT

If you have moved to a different area or if a broadcasting station’s channel number has been changed, the wrong VCR CH or CABLE CH number will be displayed on the Program screen in step 5. When this happens, set the correct guide channel number for that station. (Z pg. 32, “Changing VCR Plus+ Setting”)

NOTES:

●

Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time, channel settings, and other menu settings are lost if it lasts for more than 3 minutes. As a result, when the power is supplied again to this VCR after the power failure, the following will take place.

1. This VCR starts the Plug & Play setting automatically to

restore the clock time and channel setting.

2. If the clock time and channel setting are restored correctly,

each timer program you have made will start at its start time unless its end time has elapsed.

●

To timer-record cable channels received through a cable box, be sure to keep the cable box turned on.

TIMER RECORDING (cont.)

Changing

VCR Plus+ Setting

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

123 456

4 5

IMPORTANT

If you have moved to a different area or if a broadcasting station’s channel number has been changed, the wrong VCR CH or CABLE CH number will be displayed on the Program screen (Z step 5 on page 31). When this happens, perform the following steps to set the correct guide channel number for that station.

To ensure that VCR Plus+ timer recording operates correctly, it is necessary to set the VCR Plus+ “Guide Channel Set” for each station. Read the following information carefully.

VCR Plus+ guide channel matching

The VCR Plus+ programing system assigns a VCR Plus+ guide channel to the TV channels and the cable channels. These guide channel numbers are also called the VCR Plus+ channel codes. Most TV listings have a section, usually a chart, indicating the guide channel numbers assigned to each station. For accurate VCR Plus+ programing, the VCR Plus+ guide channel number for each station should match the channel number on which it is received in your area.

1 6

NOTES:

●

2 – 5

In many instances, the VCR Plus+ guide channel numbers for cable and broadcast TV stations DO NOT match the channel number on which it is received by your VCR or cable box. Check your TV listing, or contact your cable supplier for details.

●

Many TV stations can be viewed on cable. Check your TV listing, or contact your cable supplier for details.

2 – 5

Access Main Menu screen

Press MENU .

Access Initial Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “INITIAL SET”, then press OK or SHUTTLE

PLUS

Access Guide Channel Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “GUIDE CHANNEL SET”, then press OK or

SHUTTLE PLUS

Input guide channel number

Press the Number keys or SHUTTLE PLUS %ﬁ to input the VCR Plus+ guide channel number as shown in the TV listing, then press OK or

SHUTTLE PLUS

● If you receive your channels with a cable box and if you have properly set your Controller, “CABLE CH” appears in place of “VCR CH”. If not, refer to pages 15 – 17 and re-perform the procedure.

MAIN MENU

FUNCTION SET TUNER SET

INITIAL SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

INITIAL SET

CLOCK SET LANGUAGE ENGLISH

GUIDE CHANNEL SET

CABLE BOX SET DBS RECEIVER SET

SELECT WITH (5,∞) AND (OK) PRESS (MENU) TO END

(Ex.) When inputting the guide channel number 6 for WNJU(Ind.)

GUIDE CHANNEL SET

GUIDE CH : 6

VCR CH : – – –

PRESS NUMBER KEY (0-9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

Input receiving channel number

Press the Number keys or SHUTTLE PLUS %ﬁ to input the number of the channel on which the guide channel’s broadcasts are received, then press OK or

SHUTTLE PLUS

● Repeat steps 4 and 5 for each instance.

Return to normal screen

Press MENU .

(Ex.) If WNJU(Ind.) is received on channel 47

GUIDE CHANNEL SET

GUIDE CH : 6

VCR CH : 47

PRESS NUMBER KEY (0-9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

Express Timer Programing

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

POWER

DAILY

3 4

2 9

123 456

WEEKLY

0 7

TIMER RECORDING (cont.)

You can directly program the VCR’s timer to record up to 8 programmes, as far as a year in advance. Remember, the clock must be set before you can program the timer (Z pg. 8 or 10).

Load a cassette

Make sure the record safety tab is intact. If not, cover the hole with adhesive tape, then load it into the VCR.

● The VCR turns on, and the counter is reset, automatically.

Access PlusCode No. screen

Press PROG..

Access Program screen

Press START +/– once. (If no program is stored, “PROGRAM 1” appears.)

Set program start time

Press START +/– repeatedly to enter the time you want recording to start.

● Press and hold START +/– to increase the

time in 30-minute intervals.

PROGRAM 1

START STOP

– –:– –AM = – –:– –AM

DATE CH

– –/– –/– – – – – SP

PRESS (+/–, SP/EP, 8=DAILY,

9=WEEKLY), THEN (0K)

PRESS (PROG.) TO END

PROGRAM 1

START STOP

8:00 AM = – –:– –AM

DATE CH

– –/– –/– – – – – SP

PRESS (+/–, SP/EP, 8=DAILY,

9=WEEKLY), THEN (0K)

PRESS (PROG.) TO END

Set program stop time

Press STOP +/– repeatedly to enter the time you want recording to stop.

● Press and hold STOP +/– to increase the time in 30-minute intervals.

Set program date

Press DATE +/– . (The current date is displayed on the screen. The date you enter appears in its place.)

Set channel number

Press CH +/– .

● If you are using a DBS receiver, see “ATTENTION FOR DBS RECEIVER USERS” on next page.

● Holding down CH +/– rapidly changes the channel numbers.

Set tape speed

Press SP/EP to set the tape speed.

Return to normal screen

Press PROG. or OK. “PROGRAM COMPLETED” appears on the screen for about 5 seconds, then normal screen appears.

Engage timer recording standby mode

Press TIMER . The VCR turns off automatically and “‰” is displayed on the front display panel.

To timer-record daily (Monday–Friday) or weekly serials

Press DAILY (M-F) (number “8”) or WEEKLY (number “9”) anytime during steps 3 through 9. “DAILY” or “WEEKLY” appears on the Program screen.

● Pressing the button again makes the corresponding indication disappear.

To use the VCR while it is in timer recording standby mode

NOTES:

●

1. This VCR starts the Plug & Play setting automatically to restore the clock time and channel setting.

2. If the clock time and channel setting are restored correctly, each timer program you have made will start at its start time unless its end time has elapsed.

●

Programs that start after midnight must have the next day’s date.

●

After timer recording is completed, the VCR turns off automatically.

●

You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded.

●

To timer-record cable or satellite channels, be sure to keep the cable box or DBS receiver turned on.

ATTENTION FOR DBS RECEIVER USERS

If you are using a DBS receiver (unless “DBS RECEIVER SET” is set to “OFF” Z pg. 19), the band indication (TV, CATV or DBS) appears under the channel number indication. TV :To timer-record a regular TV broadcast

received on the VCR.

CATV :To timer-record a cable TV broadcast

received on the VCR, or through a cable box (unless “CABLE BOX SET” is set to “OFF” Z pg. 16).

DBS :To timer-record a satellite broadcast

received through a DBS receiver.

PROGRAM 1

START STOP

8:00AM = 9:00PM

DATE CH

12/24/00 110 SP

SUN DBS

PRESS (+/–, SP/EP, 8=DAILY,

9=WEEKLY, 7=DBS), THEN (0K)

PRESS (PROG.) TO END

NOTE:

If “BAND” is set to “TV” on the Tuner Set screen (Z␣ pg.␣ 13) and “CABLE BOX SET” is set to “OFF” on the Cable Box Set screen (Z␣ pg.␣ 16), “CATV” will not be displayed on the Program screen; If “BAND” is set to “CATV” or “CABLE BOX SET” is set to “ON”, “TV” will not be displayed.

If the channel number entered requires that the band be set, “7=DBS” is displayed on the screen. If this happens, press the Number key “7 (DBS) ” to select “DBS”.

24HR Quick Programing

JOG dial

REW

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

S VIDEO

NOTES:

●

If “Err” appears on the display panel, repeat the steps again.

●

When a menu screen is shown, you cannot use 24HR quick programing function. Press MENU to return to normal screen, and try again.

●

You can use 24HR quick programing function also when the VCR is turned off.

●

For 24HR quick programing function, the program overlap warning display does not appear even if some programs overlap each other.

●

Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time, channel settings, and other menu settings are lost. As a result, when the power is supplied again to this VCR after the power failure, the following will take place.

1. This VCR starts the Plug & Play setting automatically to restore the clock time and channel setting.

2. If the clock time and channel setting are restored correctly, each timer program you have made will start at its start time unless its end time has elapsed.

PLAY

–

A.DUB

24HR QUICK PROGRAM

INSERT

REC PAUSE STOP/EJECT

24HR QUICK PROGRAM

TIMER RECORDING (cont.)

You can program a timer recording that starts within 24␣ hours. Up to 8␣ timer recording programs can be made as far as a year in advance. Remember, the clock must be set before you can program the timer (Z␣ pg.␣ 8 or␣ 10).

Load a cassette

Make sure the record safety tab is intact. If not, cover the hole with adhesive tape, then load it into the VCR.

● The VCR turns on, and the counter is reset, automatically.

CH– /+

PUSH / TURN

Access 24HR quick program display.

Push 24HR QUICK PROGRAM . “ ” and start time start blinking on the display panel.

Program start time indicator

Set program start time

Turn the JOG dial to the left or right. Then, push the JOG dial. “ the display panel.

” and start time start blinking on

Program start time indicator

● One click stop of the JOG dial changes the time in 5-minute intervals.

Set program stop time

Turn the JOG dial to the left or right. Then, push the JOG dial and channel number will start blinking.

● One click stop of the JOG dial changes the time in 5-minute intervals.

Program stop time indicator

Timer warning display

A warning appears on the TV screen to tell you that the timer-recording is to start in 5␣ minutes if you are not in the timer recording standby mode at that time. Press TIMER to put the VCR into timer recording standby mode. To clear the display, press CANCEL on the Remote.

–WARNING–

TIMER RECORDING

TO START SOON

(CANCEL)

Set channel number

Turn the JOG dial to the left or right.

● You can cancel the setting at any time by pressing and holding the JOG dial for more than 3 seconds. Repeat from the step 3.

Engage timer recording standby mode

Press 24HR QUICK PROGRAM . The VCR turns off automatically and “‰” is displayed on the front display panel.

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

–2

123 456

A B

–2, 3

–3

–1

–2

Checking program settings

1 Disengage timer

Press TIMER , then press POWER.

● When “AUTO TIMER” (Z pg. 40) is set to “ON”,

you do not have to press TIMER .

2 Access Program Check screen

Press PROG. CHECK .

–4

3 Access Program screen

Press PROG. CHECK again to check more detailed information. Each time you press PROG. CHECK , the next program’s Program screen appears. When all Program screens are shown, normal screen resumes.

Canceling or changing program

settings

PR START STOP CH DATE 1 8:00P 10:00 12 12/24 2 10:00A 10:45 40 12/25 3 11:30P 1:00 125 12/25 4 5 6 7 8

PRESS (CHECK) TO NEXT

Other Useful functions for timer recording

You can also use the following functions for timer recording.

● Auto Timer (Z pg. 40)

When “AUTO TIMER” is set to “ON”, the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER to engage or disengage the timer recording standby mode.

● Auto SP = EP Timer (Z pg. 41)

If there is not enough tape to record the entire broadcast for recording in SP mode, the VCR automatically switches to EP mode to allow complete recording. This feature is especially handy when recording a broadcast of more than 2 hours in length.

1 Access Program screen

Repeat steps 1 to 3 above.

2 Cancel or change program setting

To cancel a program, press CANCEL when the Program screen you do not want is shown.

To change a program, press the appropriate button: START+/– , STOP+/– , DATE+/– , CH+/– , and/or SP/ EP when the Program screen on which you want to

make changes is shown.

3 Return to normal screen

Press PROG. CHECK as many times as necessary until no Program screen is shown.

4 Reengage timer recording standby mode

Press TIMER .

● When “AUTO TIMER” (Z pg. 40) is set to “ON”, the timer recording standby mode automatically resumes when you turn off the VCR.

10:00

11:00

12:00

10:00

11:00

12:00

10:00

11:00

12:00

123 456

–3

When programs overlap each

–3

C C

–3

–2

other

If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking.

PR START STOP CH DATE

PROGRAM NOT COMPLETED

PROGRAM OVERLAP

1 8:00P 11:00 12 12/24

2 10:00A 10:45 40 12/25 3 11:30P 1:00 125 12/25 4 9:00P 10:00 10 12/24 5 6 7 8 (5,∞), THEN (>) (PROG.) : END

EX. Program 1 (you have just made) and Program 4 overlap each other

1 Confirm overlapping programs

Overlapping programs blink on the screen.

2 Select program to modify

Press SHUTTLE PLUS %ﬁ, then press SHUTTLE

PLUS

• You can only select one of the overlapping programs.

TIMER RECORDING (cont.)

3 Cancel or change program setting

To cancel a program,

press CANCEL when the Program screen you do not want is shown. “PROGRAM COMPLETED” appears on the screen for about 5␣ seconds, then normal screen appears.

To change a program, press the appropriate button: START+/– , STOP+/– , DATE+/– , CH+/– , and/or SP/ EP when the Program screen on which you want to

make changes is shown, then press OK. “PROGRAM COMPLETED” appears on the screen for about 5 seconds, then normal screen appears.

NOTE:

If the overlap is not yet solved or another overlap occurs with the timer program setting made last after making correction on a program, the conflicting programs will be shown on the Program Check screen again. Repeat the above steps again until the overlap is solved.

ATTENTION

If there is a conflict in the timer schedule and one program overlaps with another, only the parts shown below in gray will be recorded.

Pattern 1: The program with the lower program

number will be recorded.

Program 1 Program 2

Pattern 2: The program starting earlier will be

recorded.

Program 1

Program 2

Pattern 3: The program starting earlier will be

recorded, followed by the remaining portion of the other program.

Program 1

CH10 CH40

CH10

CH40

CH10

Program 2

Not recorded

PROGRAM 4

START STOP 9:00 PM = 10:00PM DATE CH

12/24/00 10 SP

SUN

PRESS (CANCEL) TO CANCEL

PRESS (OK) TO CONFIRM

PRESS (PROG.) TO END

Not recorded

CH40

NOTE:

If you do not mind this overlap, press

timer program setting. See “ATTENTION” to the right.

Without doing anything for about 1 minute, the VCR will

finish the timer programing.

PROG.

to finish the

OTHER USEFUL FUNCTIONS

Useful Function Settings

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

You can use the other useful function settings on the Function Set screen by following the procedure described below.

● For the functions you can set on the Function Set screen, see pages 40 to 43.

Access Main Menu screen

Press MENU.

Access Function Set screen

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to “FUNCTION SET”, then press OK or SHUTTLE

PLUS

MAIN MENU

FUNCTION SET

TUNER SET INITIAL SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

1 5

123 456

2 – 4

2 3

Select Function.

Press SHUTTLE PLUS %ﬁ to move the highlight bar (arrow) to the function you want to set.

FUNCTION

VIDEO CALIBRATION ON

PICTURE CONTROL AUTO AUTO TIMER OFF SUPERIMPOSE ON

=EP TIMER OFF

AUTO SP DIGITAL R3 ON NEXT PAGE

SELECT WITH (5,∞) AND (OK) PRESS (MENU) TO END

VIDEO STABILIZER OFF

BLUE BACK ON 2ND AUDIO RECORD OFF AUDIO MONITOR HI-FI S-VHS MODE ON AV COMPU-LINK ON NEXT PAGE

FRONT AUX INPUT VIDEO

REAR AUX INPUT VIDEO S-VHS ET OFF

SELECT WITH (5,∞) AND (OK) PRESS (MENU) TO END

Change setting

Press OK or SHUTTLE PLUS #.

Return to normal screen

Press MENU.

OTHER USEFUL FUNCTIONS (cont.)

* The default setting is bold in the table below.

m VIDEO CALIBRATION

OFF

m PICTURE CONTROL

AUTO (NORM):

this. Picture quality is adjusted automatically . When “VIDEO CALIBRA TION” is “OFF”, “NORM” will appear instead of “AUTO”.

EDIT: Minimizes picture

degradation during editing (recording and playback).

SOFT: Reduces image

coarseness when viewing overplayed tapes containing much noise.

SHARP:Clearer, sharper-edged

picture when viewing images with much flat, same-colored surfaces such as cartoons.

Normally select

When this function is set to “ON”, this VCR checks the condition of the tape in use during playback and recording, and compensates to provide the highest-possible pictures. This takes place whenever you play back a tape or start recording after inserting a tape.

NOTES:

●

During playback, this function is always working even though “VIDEO CALIBRATION” appears just at the beginning of automatic tracking.

●

During recording, this function works only for the first EP recording and the first SP recording on an inserted tape. For timer recording, this function checks the tape condition both for the SP recording and the EP recording before the first timer recording starts.

●

When you play back rental tapes or tapes recorded on other VCRs, set this function either “ON” or “OFF” whichever gives you the best picture.

This function helps you to adjust the playback picture quality according to your preference.

NOTES:

●

When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not change until you select again.

●

Select "EDIT" when you are editing tapes (Z pg. 47, 48, and 51). After you finish editing the tapes, select “AUTO” (“NORM” when “VIDEO CALIBRATION” is “OFF”.)

m AUTO TIMER

OFF

m SUPERIMPOSE

OFF

● When this function is set to “ON”:

The timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER to engage or disengage the timer recording standby mode.

● When this function is set to “OFF”:

You have to press TIMER to engage or disengage the timer recording standby mode.

When this function is set to “ON”, various VCR status information (onscreen display) appears on the screen.

NOTES:

●

When you use this VCR as the playback VCR for editing a tape, be sure to set this function to “OFF”; otherwise, the VCR status information (on-screen display) will be recorded on the edited tape.

●

If you select a channel on which no signal is received, the channel number is displayed regardless of this function setting.

Refer to page 39 for setting procedures.

* The default setting is bold in the table below.

m AUTO SP = EP TIMER

OFF

m DIGITAL R3

OFF

When this function is set to “ON”, the VCR automatically switches to EP mode to allow complete recording if there is not enough tape to record the entire program while timer-recording in SP mode.

For Example . . .

Recording a program of 140 minutes in length onto a 120-minute tape

Approximately 110 minutes

SP mode

Make sure you set this function to “ON” before the timer-recording starts.

Approximately 30 minutes

EP mode

NOTES:

●

If you have programed the VCR to timer-record 2 or more programs, the second program and those thereafter may not fit on the tape with this function set to "ON". In this case, do not use this function, but change the tape speed manually during timer programing.

●

In order to ensure that the recording fits on the tape, this function may leave a slight non-recorded portion at the end of the tape.

●

There may be some noise and sound disturbance where the tape speed switches from SP to EP mode on the tape.

●

This function is not available during ITR (Instant Timer Recording), and will not work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.

When this function is set to “ON”, edge correction to the luminance signal is performed to enhance details. Normally set this function to “ON”.

NOTES:

●

Depending on the type of tape being used, picture quality may be better with “DIGITAL R3” set to “OFF”.

●

If you use this VCR as the playback VCR for editing, be sure to set “DIGITAL R3” to “OFF” before starting.

m VIDEO STABILIZER

OFF

m BLUE BACK

OFF

m 2ND AUDIO RECORD

OFF

When this function is set to “ON”, you can automatically correct vertical vibrations in the picture when playing back unstable recordings made on another VCR.

NOTES:

●

When you finish viewing a tape, be sure to set this function to “OFF”.

●

Regardless of the setting, this function has no effect during recording and during special effects playback.

●

The on-screen display may jitter vertically when this function is set to “ON”.

●

To watch recordings with close-caption, set this function to “OFF”.

When this function is set to “ON”, the TV screen becomes all blue in the following cases:

● When receiving a channel not in use.

● When stopping playback.

NOTE:

When you want to receive an unstable channel with poor signals, set this function to “OFF”.

When this function is set to “ON”;

● If a SAP program is received, the SAP audio is recorded on both the normal and Hi-Fi tracks. The main audio is not recorded.

● If a non-SAP program is received, the main audio is recorded on both the Hi-Fi and normal tracks.

When this function is set to “OFF”, the SAP audio cannot be recorded.

Refer to page 39 for setting procedures.

OTHER USEFUL FUNCTIONS (cont.)

* The default setting is bold in the table below.

m AUDIO MONITOR

HI-FI: Normally select this.

Hi-Fi sound is played back.

HI-FI L: Sound on the left Hi-Fi

channel is played back.

HI-FI R: Sound on the right Hi-Fi

channel is played back.

NORM: Sound on the normal track

is played back.

MIX: Both sounds on the Hi-Fi

track and normal track are mixed and played back.

m S-VHS MODE

OFF

This VCR can record two sound tracks simultaneously (normal and HiFi) on a tape. You can select the sound track(s) to listen to while playing back a Hi-Fi stereo tape. In addition, when playing back a prerecorded tape containing two separate audio programs on the Hi-Fi tracks, you can choose either one by selecting either “HI-FI L” or “HI-FI R”.

NOTES:

●

While playing back a monaural tape, sounds on the normal track will be heard regardless of this setting.

●

If RF connection (Z pg. 7) is used for viewing pictures on the TV, sound will be monaural even though you select “HI-FI”.

●

You can also use the monitor sound. (Z pg. 23)

You can determine which recording mode — either S-VHS mode or VHS mode — is used for recording on S-VHS tapes.

When this function is set to “ON”, you can record on S-VHS tapes with S-VHS picture quality.

When this function is set to “OFF”, you can record on S-VHS tapes with VHS picture quality.

A. MONITOR

button on the Remote to select the desired

NOTES:

• S-VHS mode allows you to make high quality video recordings with horizontal resolution of 400 lines, comparing with the 230 lines of resolution of conventional VHS recordings. To achieve the highest quality picture we recommended to record in S-VHS mode. (But remember that a conventional VHS VCR without SQPB cannot play back S-VHS tapes recorded in S-VHS mode.)

• S-VHS MODE setting does not affect recording on VHS tapes. Recording on VHS tapes is always performed in VHS mode except when using S-VHS ET mode (Z pg. 43).

m AV COMPU-LINK

OFF

The REMOTE PAUSE/AV COMPULINK terminal on the rear panel can be used as either the REMOTE PAUSE terminal or the AV COMPULINK terminal.

When this function is set to “ON”, you can use this terminal as the AV COMPULINK terminal. By connecting other JVC’s AV COMPULINK components (see the diagram on page␣ 43), including amplifiers (or receivers) and televisions, one touch control of the audio and video components linked via their AV COMPULINK connectors becomes possible.

For example: simply load a cassette in the VCR and press PLAY ( 3 ) and the AV COMPULINK components automatically turn on, the TV’s AV mode is selected and the VCR starts playback. (You do not have to press PLAY ( 3 ) if the cassette’s record safety tab is removed.)

When this function is set to “OFF”, you can use this terminal as the REMOTE PAUSE terminal. (Z pg. 47)

NOTE:

Connection varies depending on the type of JVC TV you have. Refer to the TV’s instruction manual when making this connection.

CONTINUED ON NEXT PAGE \

Refer to page 39 for setting procedures.

To AV COMPU LINK II (VCR ONLY)

To AUDIO/ VIDEO IN

AV COMPU LINK

Television

To S-VIDEO IN

S-video cable (supplied)

Audio/video cable (supplied)

Mini-plug cable (not supplied)

This VCR

To S-VIDEO OUT

* The default setting is bold in the table below.

REMOTE

OUT

ANTENNA IN

PAUSE/ AV

CABLE

BOX

IN OUT

S V

I D E O

COMPU

-LINK AUDIO

VHF/UHF TV OUT

VIDEO

To REMOTE PAUSE/ AV COMPULINK

To AUDIO/ VIDEO OUT

m FRONT AUX INPUT

VIDEO

S-VIDEO

m REAR AUX INPUT

VIDEO

S-VIDEO

m S-VHS ET

OFF

You have to select which terminal — either VIDEO (composite) or S VIDEO (Y/C separate signals) — to use as the video input terminal on the front panel.

Make sure to select the correct terminal; otherwise, you may fail in recording (editing) on this VCR.

You have to select which terminal — either VIDEO (composite) or S VIDEO (Y/C separate signals) — to use as the video input terminal on the rear panel.

Make sure you select the correct terminal; otherwise, you may fail in recording (editing) on this VCR.

This function allows you to record on VHS tapes with S-VHS picture quality. Tapes recorded using this function can be played back on a VCR equipped with the S-VHS ET function. The S-VHS indicator lights up on the front display panel when "S-VHS ET" is set to "ON".

NOTES:

●

Before recording, make sure that “VIDEO CALIBRATION” is set to “ON”. (Z pg. 40)

●

You cannot activate the S-VHS ET function... – while recording is in progress. – while timer-recording or Instant Timer Recording (Z pg. 26) is in progress. – while Video Calibration (Z pg. 40) is in progress.

●

S-VHS ET does not work with S-VHS tapes.

●

To keep the highest quality recording and playback pictures over a long period of time, S-VHS recording on S-VHS tapes is recommended.

●

Use of high grade tapes are recommended for S-VHS ET recordings. On some tapes, picture quality will not improves even if the S-VHS ET function is used. Check the recording quality before you start important recordings.

●

You can play back S-VHS ET recordings on most of S-VHS VCRs and of VHS VCR equipped with SQPB (S-VHS QUASI PLAYBACK) function. (Notice some VCRs are not compatible with this function.)

●

While playing back a tape recorded with this function on some tapes, noise may appear. (If playback picture becomes blurred or interrupted, use a cleaning cassette.)

●

During special effect playback (Z pg. 28), noise may appear. If special effect playback is performed frequently on a tape recorded with this function, the tape may be damaged and picture may be deteriorated.

Refer to page 39 for setting procedures.

Satellite Auto Recording

REC LINK lamp

REW

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

123 456

S VIDEO

PLAY

–

A.DUB

24HR QUICK PROGRAM

INSERT

REC PAUSE STOP/EJECT

OTHER USEFUL FUNCTIONS (cont.)

This function allows you to automatically record a satellite program which is timer-programed on your DBS receiver.

Preparation: Connect a DBS receiver to the AUDIO/ VIDEO IN or S VIDEO IN (L-1) connectors* on the rear; otherwise, you cannot use this function.

• You can also connect the cable box if it has a timer.

To use these connectors, you have to select which one to use

(Z pg. 43).

Set timer program on DBS receiver

• For timer programing method, refer to the manual supplied with the DBS receiver.

CH– /+

PUSH / TURN

Load a cassette

Make sure the record safety tab is intact.

Set tape speed

Press SP/EP ( ) to set the recording speed.

Engage Satellite Auto Recording standby

mode

Press REC LINK. The VCR turns off automatically and the REC LINK lamp lights (Satellite Auto Recording standby mode). When signals come into the VCR from the DBS receiver, the VCR starts recording (the REC LINK lamp blinks), and stops recording and goes off when signals stop coming in.

• Each time you press the button, Satellite Auto Recording standby mode turns on and off. When it is off, the REC LINK lamp goes off.

IMPORTANT: Be sure not to turn on the DBS receiver before the program starts broadcasting; otherwise, the VCR will start recording when the DBS receiver is turned on.

NOTES:

●

While the Satellite Auto Recording standby mode or after Satellite Auto Recording is finished, the VCR will not enter the timer recording standby mode even though “AUTO TIMER” is set to “ON”. (Z pg. 40)

●

If you turn off this VCR while Satellite Auto Recording is in progress, recording stops.

●

Video Calibration (Z pg. 40) does not work while Satellite Auto Recording is in progress.

●

Auto Clock (Z pg. 11) does not work while in the Satellite Auto Recording standby mode.

●

The VCR may not record a short portion at the beginning of the program or may record slightly longer than the actual length of the program when Satellite Auto Recording method is used.

●

If you engage the Satellite Auto Recording standby mode while the DBS receiver is turned on, the VCR will not start Satellite Auto Recording even though the REC LINK lamp blinks. When you turn off and on the DBS receiver once again, the VCR starts recording.

●

If you have connected another component other than a DBS receiver (or cable box) to the AUDIO/VIDEO IN or S VIDEO IN (L-1) connectors, be sure not to engage the Satellite Auto Recording standby mode; otherwise, the VCR will start recording when the connected component is turned on.

●

Satellite Auto Recording and timer-recording cannot be performed at the same time.

●

If the REC LINK lamp does not light but blinks quickly in the Satellite Auto Recording standby mode (even though your DBS receiver is turned off), Satellite Auto Recording will not work properly. If this is the case, perform “Express Timer Programing” (Z pg. 34) to timer-record a satellite program. (Some DBS receivers output signals even if the power is off. Satellite Auto Recording is not possible with those DBS receivers.)

Child Lock

POWER

You can disable the VCR operations.

● You can only use the Remote for this operation.

While the VCR is turned on, press and hold POWER on the Remote for more than 10 seconds.

The VCR turns off, and “CL” appears on the front display panel for about 5 seconds, then the clock time appears again.

123 456

TIMER

● The child lock function is now activated and you

cannot turn on the VCR by pressing POWER on the front panel.

To release the child lock, press and hold POWER on the Remote until the VCR turns on.

● Pressing TIMER during timer recording, unplugging the

AC power cord or a power outage also releases the child lock.

NOTES:

●

When the child lock function is in use, keep the Remote out of the children’s reach.

●

Timer recording programs will be performed even if the child lock function is activated.

●

If any button on the VCR or on the Remote is pressed when the child lock function is activated, “CL” appears on the front display panel for about 5 seconds, then the clock time appears again.

EDITING

Edit From Camcorder

Connection

This VCR (for recording)

POWER

S VIDEO

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

To AUDIO/ VIDEO Input

Audio/video cable (supplied)

To S VIDEO Input*

S-video cable (supplied)

To Audio/video output

To rear panel REMOTE PAUSE/ AV COMPULINK connector

Mini-plug cable (not supplied) (JVC camcorder only)

PLAY

A.DUB

24HR QUICK PROGRAM

INSERT

REW

–

REC PAUSE STOP/EJECT

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

S VIDEO

PLAY

A.DUB

24HR QUICK PROGRAM

INSERT

–

REC PAUSE STOP/EJECT

CH– /+

PUSH / TURN

REW

CH– /+

PUSH / TURN

123 456

To EDIT

To S-video output

Camcorder (for playback)

Various connection for editing tapes

The following three methods can be used for editing tapes.

●

VHS to S-VHS editing (VIDEO-VIDEO connection): Although the picture quality is inherently limited by the original VHS quality, the edited tape has better picture quality than those made by VHS-to-VHS editing.

●

S-VHS to VHS editing (VIDEO-VIDEO connection): Since the original source is recorded in S-VHS mode, the edited tape has better picture quality than those made by VHS-to-VHS editing.

●

S-VHS to S-VHS (S-VIDEO connection): Original picture quality of S-VHS made can be duplicated with minimal picture degradation. This is the best editing method you can use on S-VHS VCRs.

4 – 7

4 – 6

You can use a camcorder as the playback VCR and your VCR as the recording VCR

Make connections

Connect an audio/video cable between the camcorder’s audio/video output connectors and your VCR’s audio/video input connectors.

● When the JVC camcorder is equipped with the Master Edit Control, you can control the VCR from the camcorder. Connect the mini-plug cable (not supplied with this VCR) as illustrated to the left.

● When using a camcorder with a monaural output, connect the audio output connector on the camcorder to the left audio input connector on this VCR.

Load a cassette

Insert the cassette to be recorded on into this VCR (for recording).

Select input mode on this VCR

Select “L-1” — when connecting the camcorder

to the audio/video input connectors on the rear panel.

Select “F-1” — when connecting the camcorder

to the audio/video input connectors on the front panel.

On the front panel: Push the JOG dial, then turn it to the left or right.

On the Remote: Press the Number key "0 (AUX)" and/or CH +/–.

Select video input terminal

Follow the procedure described on pages 39 and

43.

When using S VIDEO terminal, set “FRONT AUX INPUT” (or “REAR AUX INPUT” if you use the connectors on the rear) to “S-VIDEO”.

When using VIDEO terminal, set “FRONT AUX INPUT” (or “REAR AUX INPUT”) to “VIDEO”.

Set “AV COMPU-LINK” to “OFF”

Follow the procedure described on pages 39 and

42.

● The REMOTE PAUSE/AV COMPU-LINK connector works as the Remote Pause connector when “AV COMPU-LINK” is set to “OFF”.

Return to normal screen

Press MENU.

Start playback

Set the camcorder to its play mode.

NOTE:

If the camcorder is equipped with a superimpose/OSD disable feature then set it to “OFF” before starting playback.

Start recording

On the front panel: Press REC ( ¶ ).

On the Remote: Press REC ( ¶ ) and PLAY ( 3 ) at the same time.

● If you are using a Master Edit Control-equipped JVC camcorder, recording starts automatically on this VCR. (Refer to camcorder’s instruction manual.)

NOTE:

Be sure to select “AUTO” for “PICTURE CONTROL” (or “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish dubbing the tapes (Z pg. 39 and 40).

Set “PICTURE CONTROL” to “EDIT”

Follow the procedure described on pages 39 and

40.

If your camcorder is a JVC Master Edit Controlequipped type — go to step 6. If your camcorder is NOT a JVC Master Edit Control-equipped type — go to step 7.

Edit To Or From Another VCR

Connection

Ex. When using this VCR as the playback VCR

This VCR (for playback)

REMOTE

OUT

ANTENNA IN

PAUSE/ AV

COMPU

-LINK AUDIO

VHF/UHF

TV OUT

VIDEO

To AUDIO/ VIDEO OUT

Audio/video cable (supplied)

To Audio/ video Input

To S VIDEO

S-video cable (supplied)

To S-video Input

OUT

CABLE

BOX

IN OUT

S V

I D E O

EDITING (cont.)

Load cassettes

Insert the playback cassette into the playback VCR and the cassette to be recorded on into the recording VCR.

Select input mode on recording VCR

Select the correct external input on the other VCR.

● On this VCR (when using this VCR as the recording VCR); Select “L-1” — when connecting the other VCR

to the audio/video input connectors on the rear panel;

Select “F-1” — when connecting the other VCR

to the audio/video input connectors on the front panel.

On the front panel:

Push the JOG dial, then turn it to the left or right.

On the Remote: Press the Number key "0 (AUX)" and/or CH +/–.

Select video input terminal on recording

VCR

When using this VCR as the recording VCR, follow the procedure described on pages 39 and

43.

When using S VIDEO terminal, set “FRONT AUX INPUT” (or “REAR AUX INPUT” if you use the connectors on the rear) to “S-VIDEO”.

When using VIDEO terminal, set “FRONT AUX INPUT” (or “REAR AUX INPUT”) to “VIDEO”.

Another VCR (for recording)

You can use your VCR as the playback or recording VCR.

● Refer also to the other VCR’s instruction manual for connection and its operations.

Make connections

Connect an audio/video cable between the playback VCR’s audio/video output connectors and the recording VCR’s audio/video input connectors.

● When using this VCR as the recording VCR, connect this VCR’s audio/video input connectors to the audio/video output connectors on the other VCR. If the playback VCR is monaural, connect the audio output connector on the playback VCR to the left audio input connector on this VCR.

Select edit mode

On this VCR, set “PICTURE CONTROL” to “EDIT” by following the procedure described on pages 39 and 40.

Start playback

Press PLAY ( 3 ) on the playback VCR.

NOTE:

If the playback VCR is equipped with a superimpose/ OSD disable feature then set it to “OFF” before starting playback (Z pg. 39 and 40).

Start recording

Press REC ( ¶ ) on the recording VCR.

NOTE:

Be sure to select “AUTO” for “PICTURE CONTROL” (or “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish dubbing the tapes (Z pg. 39 and 40).

Audio Dubbing

Connection

This VCR (for recording)

REW

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

S VIDEO

To AUDIO IN

To Audio output

PLAY

–

A.DUB

24HR QUICK

PROGRAM

INSERT

REC PAUSE STOP/EJECT

Audio cable (not supplied)

CH– /+

PUSH / TURN

Load a cassette and prepare the audio

source

Select input mode

Select “F-1” — when connecting the audio

component to the audio input connectors on the front panel.

Select “L-1” — when connecting the audio

component to the audio input connectors on the rear panel.

On the front panel: Push the JOG dial, then turn it to the left or right.

On the Remote: Press the Number key "0 (AUX)" and/or CH +/–.

Locate start point

1 Press PLAY ( 3 ) to start playback. 2 Press PAUSE ( 8 ) when you find the beginning

of the scene for which you want to audio-dub.

CD player (as the audio source)

●

Audio Dubbing is also possible using the audio input connectors on the rear panel.

You can replace sounds recorded on the normal track with new sounds — for example, your favorite song played back on the CD player.

● Refer also to the other audio component’s instruction manual for connection and its operations.

Normal track

Before audio dubbing

Video and Hi-Fi track

After audio dubbing

Make connections

Connect an audio cable between the VCR’s audio input connectors and the audio component’s audio output connectors.

● If the audio component is monaural, connect the AUDIO L (MONO) input connector on the VCR.

Activate editing mode

Press A.DUB on the front panel.

● The VCR enters the Audio Dubbing pause mode. blinks, and light up on the front

●

display panel.

Start audio dubbing

Start playing the audio source and press PLAY ( 3 ) on this VCR.

● blinks and is displayed on the front

display panel.

To stop audio dubbing

Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

● Audio dubbing automatically stops when the counter reading becomes "0:00:00", and the VCR starts normal playback.

NOTES:

●

During Audio Dubbing, the sound recorded on the normal track is selected as the monitor sound. If you want to listen to the Hi-Fi or mixed sound (Hi-Fi sound and monaural sound), see "Selecting monitor sound — Audio Monitor" (Z pg. 23).

●

Audio Dubbing cannot be performed on a tape with its record safety tab removed.

●

When playing back an audio-dubbed tape, select the sound you want. See "Selecting monitor sound — Audio Monitor" (Z pg. 23).

●

Picture may be distorted if you pause Audio Dubbing.

Insert Editing and AV Dubbing

Connection

This VCR (for recording)

REW

POWER

S VIDEO

S-video

cable

(supplied)

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

To VIDEO/ AUDIO IN

Audio/video cable (supplied)

PLAY

A.DUB

24HR QUICK

PROGRAM

INSERT

–

REC PAUSE STOP/EJECT

CH– /+

PUSH / TURN

EDITING (cont.)

Refer also to the other component’s instruction manual for connection and its operations.

Insert Editing: You can replace a recorded scene with new scene recorded on another tape or with other material. Both the picture and the sound recorded on the Hi-Fi sound track are replaced at the same time.

Audio/Video Dubbing: You can perform Audio Dubbing and Insert Editing at the same time. This means that the picture and the sounds recorded on the Hi-Fi sound track and on the normal track are replaced at the same time.

• For Audio/Video Dubbing, you can edit pictures and sound using different sources; connect a video source to the video input connector, and an audio source to the audio input connectors.

Insert Editing

Source tape

Edited tape

Before editing

Normal track

To S-video output

To Audio/ video output

Another VCR (for playback)

●

Insert Editing and AV Dubbing are also possible using the audio/video connectors on the rear panel.

After editing

Video and Hi-Fi track

AV Dubbing

Source tape

Edited tape

Before editing

After editing

Make connections

Connect an audio/video cable between the VCR’s audio/video input connectors and the other component’s audio/video output connectors.

Prepare tapes

Load the source tape on the other VCR, and the tape to be edited on this VCR.

Select input mode

Select “F-1” — when connecting the other

component to the audio/video input connectors on the front panel.

Select “L-1” — when connecting the other

component to the audio/video input connectors on the rear panel.

On the front panel: Push the JOG dial, then turn it to the left or right.

On the Remote: Press the Number key "0 (AUX)" and/or CH +/–.

Select video input terminal

Follow the procedure described on pages 39 and

43. When using S VIDEO terminal, set “FRONT AUX INPUT” (or “REAR AUX INPUT” if you use the connectors on the rear) to “S-VIDEO”.

When using VIDEO terminal, set “FRONT AUX INPUT” (or “REAR AUX INPUT”) to “VIDEO”.

Locate start point

Use REW ( ) or JOG dial to reverse the tape

(See “Special Effect Playback”: Z pg. 28).

When you find the begining of the scene you

want to edit, press PAUSE ( 8 ).

Activate editing mode

Press INSERT on the front panel.

● Make sure that the recording format (VHS, SVHS or S-VHS ET) on the VCR is the same as that of the original recording on the tape.

● During Insert Editing pause mode (

light up on the front display panel.)

● For AV Dubbing, after pressing INSERT, press A.DUB also. During AV Dubbing insert pause

mode ( the front display panel.)

and blink, and lights up on

Start editing

Press PLAY ( 3 ) on this VCR, and start playback on the other component at the same time.

● During Insert Editing mode ( and light up on the front display panel.)

● During AV Dubbing mode ( and blink on the front display panel.)

● When the counter reading becomes “0:00:00”, editing automatically stops, and the VCR starts normal playback.

, and

Select edit mode

On this VCR, set “PICTURE CONTROL” to “EDIT” by following the procedure described on pages 39 and 40.

Locate end point

1 Press PLAY ( 3 ) to start playback. 2 Press PAUSE ( 8 ) when you find the end of

the scene for which you want to edit.

3 Press C. RESET so that the counter reading

becomes “0:00:00”.

NOTE:

You can also use to locate the end point (See “Special Effect Playback”:

pg. 28) .

REW ( )

FF ( )

, or

JOG

dial

To stop editing any time during recording

Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

NOTES:

●

Be sure to select “AUTO” for “PICTURE CONTROL” (or “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish editing the tapes (Z pg. 39 and 40).

●

Editing cannot be performed on a tape with its record safety tab removed.

●

The recording speed (SP/EP) is determined by the previous recording to be replaced. If the recording speed changes on the tape to be edited while editing the tape, the inserted picture will be distorted where the recording speed changes.

●

When you edit a tape, a small portion of the recording preceding to the editing start point will be erased from the edited tape.

TV Brand

MULTI-BRAND REMOTE CONTROL

This Remote can control some functions of remote controllable TVs of the brands listed below. Without setting, you can control a JVC TV.

Setting

2 –1 4

TV/VCR

123 456 7

89 0

2 –2

POWER

2 –3

Number

2 –4

ENTER

TV VOL +/–

Turn on the TV

Turn on the TV using the Power button on the TV or its Remote.

Set TV brand code

Follow the example shown below.

1 Press and hold TV. 2 Press MBR SET. 3 Press the Number keys to enter your TV’s

brand code by referring to the table below.

4 Press OK, and release TV.

The TV should turn off. If it does, try other operations below. (Z step 3).

● Once you have set the Remote to operate the TV, you do not have to set it until you replace the batteries from the Remote.

● PANASONIC has two codes. If the TV does not function with one code, try entering the other.

Operate TV

While holding down TV, press one of the following buttons: POWER, TV/VCR, TV CH +/–,

(TV Muting), TV VOL +/–, and Number

keys.

● For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

TV BRAND NAME BRAND CODE

JVC 01, 03 HITACHI 10 MAGNAVOX 02 MITSUBISHI 03 PANASONIC 04, 11 RCA 05 SHARP 06 SONY 07 SAMSUNG 12 SANYO 13 SEARS 13 TOSHIBA 08 ZENITH 09

TV CH +/–

NOTES:

●

Depending on the type of TV, some or all functions cannot be operated using this Remote.

●

It’s not possible to operate a TV not equipped with a remote sensor.

(Ex.) To set Remote to RCA 05:

Hold down

MBRSET

A/B

Press in succession

Release

Cable Box Brand Setting

This Remote can control some functions of the cable boxes of the brands listed below. Some cable box brands have more than one code. If your cable box does not function with a specified code, try other codes.

Turn on the cable box

Turn on the cable box using the Power button on the cable box or its Remote.

POWER

2 –1 4

CABLE/DBS

CABLE BOX BRAND NAME BRAND CODE

ARCHER 01, 05, 17 CABLETENNA 01, 17 CABLEVIEW 15, 16, 17, 21, 25 CITIZEN 15, 16, 17, 21, 25 CURTIS 02 DIAMOND 01, 17 EASTERN 19 GC BRAND 15, 16, 17, 21, 25 GEMINI 15 GENERAL INSTRUMENTS 01, 04, 06, 11, 12, 15, 28 HAMLIN 10, 18, 19, 23 JASCO 15 JERROLD 01, 04, 06, 11, 12, 15, 28 NOVAVISION 02 OAK 07 PANASONIC 13, 14 PULSER 15, 16, 17, 21, 25 RCA 13, 14 REGAL 10, 18, 19, 23 REGENCY 19 REMBRANDT 01, 16, 17 SAMSUNG 05, 16, 24 SCIENTIFIC ATLANTA 02 SIGMA 07 SL MARX 05, 16, 17, 24, 25 SPRUCER 13, 14 STARGATE 05, 15, 16, 17, 21, 24, 25 TELEVIEW 05, 16, 24 TOCOM 01, 04, 16 UNIKA 01, 17 UNIVERSAL 16, 17, 25 VIDEOWAY 03, 09, 22 ZENITH 03, 09, 22

123 456

2 –2

2 –3

Number

2 –4

ENTER

TV CH +/–

Enter cable box brand code

Follow the example shown below.

1 Press and hold CABLE/DBS. 2 Press MBR SET. 3 Press the Number keys to enter your cable

box’s brand code by referring to the table below.

4 Press OK, and release CABLE/DBS.

The cable box should turn off. If it does, try other operations below. (Z step 3).

● Once you have set the Remote to operate the cable box, you do not have to set it until you replace the batteries from the Remote.

Operate cable box

While holding down CABLE/DBS, press one of the following buttons: POWER, TV CH +/–, and Number keys.

● For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

● To change the cable box’s channels, press TV CH +/– or the Number keys. (The CH +/–

button can be used to change the VCR’s channels only.)

NOTES:

●

Depending on the type of cable box, some or all functions cannot be operated using this Remote.

●

It’s not possible to operate a cable box not equipped with a remote sensor.

●

It’s not possible to set the Remote for both your cable box and a DBS receiver at the same time. You can only set the Remote control to operate one of these units at a time.

(Ex.) To set the Remote to RCA 14:

MBRSET

CABLE/

DBS

Hold down

A/B

Press in succession

Release

DBS Receiver

MULTI-BRAND REMOTE CONTROL (cont.)

This Remote can control some functions of the DBS (Direct Broadcast Satellite) receivers of the brands listed below.

Brand Setting

POWER

2 –1 4

CABLE/DBS

123 456

2 –2

2 –3

Number

2 –4

ENTER

TV CH +/–

Turn on the DBS receiver

Turn on the DBS receiver using the Power button on the DBS receiver or its Remote.

Enter DBS receiver brand code

Follow the example shown below.

1 Press and hold CABLE/DBS. 2 Press MBR SET. 3 Press the Number keys to enter your DBS

receiver’s brand code by referring to the table below.

4 Press OK, and release CABLE/DBS.

The DBS receiver should turn off. If it does, try other operations below (Z step 3).

● Once you have set the Remote to operate the DBS receiver, you do not have to set it until you replace the batteries from the Remote.

Operate DBS receiver

While holding down CABLE/DBS, press one of the following buttons: POWER, TV CH +/–, and Number keys.

● For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

● To change the DBS receiver’s channels, press TV CH +/– or the Number keys. (The CH +/– button can be used to change the VCR’s channels only.)

DBS BRAND NAME BRAND CODE

JVC (DISH Network) 51 ECHOSTAR (DISH Network) 51 PRIMESTAR 50 SONY (DSS) 41 RCA (DSS) 40

NOTES:

●

Depending on the type of DBS receiver, some or all functions cannot be operated using this Remote.

●

It’s not possible to operate a DBS receiver not equipped with a remote sensor.

●

It's not possible to set the Remote for both your DBS receiver and a cable box at the same time. You can only set the Remote to operate one of these units at a time.

(Ex.) To set the Remote to JVC 51:

CABLE/

Hold

down

DBS

MBRSET

A/B

Press in succession

Release

Changing

MBRSET

A/B

Remote Control Code

REW

A.DUB

INSERT

PLAY

–

24HR QUICK PROGRAM

REC PAUSE STOP/EJECT

1 –1, 3

1 –2

CH– /+

PUSH / TURN

POWER

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

VCR

S VIDEO

123 456

This Remote is capable of transmitting two control codes; one set to respond to A code control signals and another set to respond to B code control signals. This Remote control is preset to send A code signals because your VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code control signals. When using two JVC VCRs, set two VCRs and their Remotes to different codes, so that you can operate these VCRs separately.

Set remote control code for Remote

1 Press and hold A/B. 2 Press the Number key “2”. 3 Press OK, and release A/B.

● The Remote now can transmit B code control signals.

Check remote control code for VCR

Press and hold 3 on the VCR for more than 5␣ seconds while the VCR is turned off. The code currently set appears on the display panel.

Change code for VCR

Press any key on the Remote.

● The VCR now responds to B code control signals.

● To set the Remote and the VCR back to A code control signals, repeat the same procedure as shown above except pressing the Number key “1” in step 2 of 1.

To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote control code for the Remote between A and B (Z step

1), keeping two VCRs to different control codes.

● Press the Number key “1” for A code control signals and the Number key “2” for B code control signals. (To change only the remote control code for the Remote, DO NOT perform steps 2 and 3 .)

1 –3

(Ex.) To set Remote to B code:

Release

Hold down

Press in succession

TROUBLESHOOTING

Before requesting service, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you from the trouble of sending your VCR off for repair.

POWER

SYMPTOM

1. The power will not come on.

2. The clock works, but the VCR’s power will not come on.

3. The Remote will not function.

TAPE TRANSPORT

SYMPTOM

1. The cassette gets stuck partway during loading, and is ejected.

PLAYBACK

SYMPTOM

1. The tape is running but the picture will not appear.

2. Breaks are noticeable in Hi-Fi sound track.

3. The playback picture is blurred or interrupted, even though TV broadcasts are clear. Or “USE CLEANING CASSETTE” appears on the screen.

4. The Hi-Fi sound cannot be heard.

POSSIBLE CAUSE

● The AC power cord is disconnected.

● Child lock is on.

● The VCR is in the timer recording

standby mode with “AUTO TIMER” set to “OFF” (Z pg. 40).

● The child lock function is activated.

● The batteries are discharged.

● Timer is on.

● Remote control A/B code is wrong.

POSSIBLE CAUSE

● The cassette was inserted incorrectly.

POSSIBLE CAUSE

● If the RF connection (Z pg. 7) is used to view the picture, the channel on the TV is set incorrectly.

● If the AV connection (Z pg. 7) is used to view the picture, the TV receiver is set to the wrong mode.

● Automatic tracking is engaged.

● The video heads may be dirty.

● Audio Monitor setting is incorrect.

CORRECTIVE ACTION

Connect the AC power cord. Turn off child lock function (Z pg. 45).

Press TIMER to disengage.

Press and hold POWER for more than 10 seconds to release the child lock function (Z pg. 45).

Replace batteries. Press TIMER button on the remote. Reset A/B code (Z pg. 55).

CORRECTIVE ACTION

Make sure the cassette’s window is facing up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Then insert the cassette.

CORRECTIVE ACTION

Select channel 3 or 4 on the TV.

Select the AV mode on the TV.

Disengage auto tracking and adjust the tracking manually (Z pg. 23).

The heads must be cleaned. Use a dry cleaning cassette –TCL-2UX– or consult your JVC dealer.

Set Audio Monitor to “HI-FI” (Z pg. 23 or 42).

RECORDING

SYMPTOM

1. Recording will not start.

2. TV broadcasts will not be recorded properly.

3. Tape-to-tape editing will not work.

POSSIBLE CAUSE

● There is no cassette loaded.

● The loaded cassette has had its

record safety tab removed.

● The VCR has been set to “L-1” or “F1” input mode by mistake.

● The components have been incorrectly connected, or correct video connector (S VIDEO or VIDEO) is not selected.

● The power to one or more of the units has not been turned on.

● The recording VCR’s input mode has been set incorrectly.

CORRECTIVE ACTION

Insert a cassette. Remove the cassette and cover the hole with adhesive tape, or load a cassette on which the record safety tab is intact.

Select the appropriate channel on the VCR.

Connect the components correctly (Z pg. 46 – 51) or check “REAR AUX INPUT or “FRONT AUX INPUT” setting (Z␣ pg.␣ 43). Make sure the power to all units is on.

Select the appropriate input mode on the recording VCR.

TIMER RECORDING

SYMPTOM

1. Timer recording will not work.

2. Timer programing will not work.

3. ‰ and ] on the front display panel will not stop blinking.

4. ‰ blinks for 10 seconds and the timer mode is disengaged.

5. The power shuts off and ‰ and ] will not stop blinking.

6. Cable channels are not automatically switched during timer recording.

7. Satellite channels are not automatically switched during timer recording.

8. Timer recording begins as scheduled, but the channel is always incorrect.

9. You moved, and now VCR Plus+ system does not work properly.

10.“PROGRAM FULL” is displayed on the screen.

POSSIBLE CAUSE

● The clock and/or the timer have been set incorrectly.

● The timer is not engaged.

● The VCR has not been set up properly.

● Timer recording is in progress.

● The timer is engaged but there is no

cassette loaded.

● The loaded cassette has had its record safety tab removed.

● TIMER has been pressed when there are no programs in memory, or the timer recording program has not been set correctly.

● The tape reaches its end during timer recording.

● The Controller is not properly connected to the VCR.

● The output channel selected in the Cable Box Set screen is incorrect.

● The cable box is turned off.

● The Controller is not properly

connected to the VCR.

● The output channel selected in the DBS Receiver Set screen is incorrect.

● The VCR is not set correctly to control the DBS receiver.

● The DBS receiver is turned off.

● Even though you do not use an

external cable box or DBS receiver, “CABLE BOX SET” is set to “ON” or “DBS RECEIVER SET” is set to “ON”.

● The receivable stations in the new area are received on different channels than those in the previous area.

● All 8 programs of the VCR’s timer memory are used.

CORRECTIVE ACTION

Set the clock and/or timer correctly.

Press TIMER and make sure that ‰ appears on the front display panel. Re-perform the set-up procedures. Make sure you have compensated for guide channel and VCR or cable box channel number mismatches (Z pg. 32).

Timer programing cannot be performed when timer recording is in progress. Wait until it finishes.

Load a cassette with the record safety tab intact, or with the hole covered with adhesive tape. Remove the cassette and cover its hole with adhesive tape, or replace it with a cassette on which the safety tab is intact.

Check the programed data and set again if necessary, then press TIMER again.

The program may not have been recorded in its entirety. Next time be sure you have enough time on the tape to record the entire broadcast.

Connect the Controller correctly (Z pg. 15). After confirming your cable box’s output channel number, re-access the Cable Box Set screen and select the correct number (Z pg. 16). Make sure the power is on before timer recording starts.

Connect the Controller correctly (Z pg. 18). After confirming your DBS receiver’s output channel number, re-access the DBS Receiver Set screen and select the correct number (Z pg. 19). Set the correct DBS receiver brand code (Z pg. 20). Make sure the power is on before timer recording starts.

Set “CABLE BOX SET” to “OFF” (Z pg. 16) or “DBS RECEIVER SET” is set to “OFF” (Z pg. 19).

Re-perform the Changing VCR Plus+ Setting procedure (Z pg. 32).

Wait until a space in memory clears, or cancel unnecessary program information (Z pg. 37).

CONTINUED ON NEXT PAGE \

INDEX

Accidental erasure prevention 26 AUDIO MONITOR 42 Audio Monitor 23 Auto Daylight Saving Time 11 AUTO SP = EP TIMER 41 AUTO TIMER 40 Automatic tracking 23 AV COMPU-LINK 42

Basic connections

AV connection 6 RF connection 6 S-video connection 6

BLUE BACK 41

Cable box control setting 15

Brand 16 Installing Controller 15

Output channel 16 Channel No. indication 26 Clock setting 10

Manual setting 12

Preparation 10

Semiauto setting 11 Clock time 22, 26 Contents 5 Counter reset 22, 26

DBS receiver control setting 18

Brand 19

Installing Controller 18

Output channel 19 Digital TBC/NR 24 DIGITAL R3 41

Editing

From a camcorder 46

From another VCR 48

To another VCR 48 Express timer programing 34

FRONT AUX INPUT 43 Function Set screen 39

Guide channel 32

Host channel 8

Index Search 23 Instant Review 24 Instant Timer Recording (ITR) 26

Language setting 9

Manual tracking 23 Multi-Brand Remote

Setting cable box brand 53 Setting DBS receiver brand 54 Setting TV brand 52

Next Function Memory 23

On-screen display 27

PBS channel 8 PICTURE CONTROL 40 Playback 21 Plug & Play 8

REAR AUX INPUT 43 Recording 25 Recording Resume Function 27 Repeat play 22

S-VHS MODE 42 S-VHS ET 43 Satellite Auto Recording 44 Special effect playback

Frame-by-Frame Playback 29 High-Speed Picture Search 28 How to use the JOG dial 28 How to use the SHUTTLE PLUS

buttons 29 Picture Search 28 Skip Search 29 Slow Motion Playback 29 Still Picture Playback 29 Variable-Speed Picture Search 28

Specifications 65 SUPERIMPOSE 40

Tape speed 25, 44 Time counter 22, 26 Time zone selection 11 Timer recording

Canceling 37 Changing 37 Checking 37 Express 34 Guide channel setting 32

VCR Plus+ 30 Timer warning display 36 Tracking 23 Troubleshooting 56 Tuner setting

Adding channels 14

Auto Channel Set 13

Deleting channels 14

Manual Channel Set 14

VCR Plus+ timer programing 30 VIDEO CALIBRATION 40 VIDEO STABILIZER 41

24HR quick programing 36 2ND AUDIO RECORD 41

Front panel

POWER

S VIDEO

VIDEO (MONO)L—AUDIO—R

REC LINK

DIGITAL TBC/NR

SP EP

1 POWER button : Z pg. 21, 25 2 Cassette loading slot 3 PLAY ( # ) button : Z pg. 21 4 Advanced JOG dial : Z pg. 21, 25, 28 5 S VIDEO input connector : Z pg. 46, 50 6 AUDIO/VIDEO input connectors : Z pg. 49, 50 7 DIGITAL TBC/NR button and lamp: Z pg. 24 8 REC LINK button and lamp : Z pg. 44 9 Front display panel : Z pg. 62 0 Remote sensor

PLAY

A.DUB

24HR QUICK

VCR

!876

INSERT

PROGRAM

REW

–

REC PAUSE STOP/EJECT

! INSERT button : Z pg. 51 @ A.DUB button : Z pg. 49 # 24HR QUICK PROGRAM button : Z pg. 36 $ REC ( ¶ ) button : Z pg. 25, 26 % PAUSE ( 8 ) button : Z pg. 25, 29 ^ STOP/EJECT ( 7 / 0 ) button : Z pg. 21, 25

CH– /+

PUSH / TURN

^%$#9

Front display panel

INDEX (cont.)

1 Symbolic Mode Indicators

STILL: PLAY: FF/REW VARIABLE SHUTTLE SEARCH:

AUDIO DUBBING:

AUDIO DUBBING PAUSE:

INSERT:

INSERT PAUSE:

AUDIO DUBBING INSERT:

AUDIO DUBBING INSERT PAUSE:

SLOW:

RECORD:

RECORD PAUSE:

2 43

VCR

2 Tape speed indicators 3 Program start time and stop time indicator :

Z␣ pg.␣ 36

4 Timer mode indicator : Z pg. 31, 35 5 Tape remaining time indicator : Z pg. 22, 26 6 S-VHS indicator : Z pg. 21, 43 7 VCR mode indicator : Z pg. 25, 26 8 Cassette mark 9 Channel and auxiliary input (“L-1” and “F-1”)

Counter reading : Z pg. 22, 26 Clock time : Z pg. 22, 26

Rear panel

1 2

3 4

0 !

1 AC power cord : Z pg. 6 2 CABLE BOX Controller connector :

Z pg. 15, 18

3 REMOTE PAUSE/AV COMPULINK terminal

● REMOTE PAUSE terminal : Z pg. 42, 46

● AV COMPULINK terminal : Z pg. 42

On-screen display

OUT

ANTENNA IN

VHF/UHF

TV OUT

IN OUT

S V

I D E O

5 6

CABLE

BOX

REMOTE PAUSE/ AV COMPU

-LINK AUDIO

VIDEO

4 ANTENNA IN terminal : Z pg. 6 5 S VIDEO IN connector : Z pg. 50 6 S VIDEO OUT connector : Z pg. 6 7 AUDIO/VIDEO IN connectors : Z pg. 50 8 AUDIO/VIDEO OUT connectors : Z pg. 48 9 TV OUT terminal : Z pg. 6

CH 125 RECORD THU 12:00 AM PAUSE STEREO –WARNING– SP SAP TIMER RECORDING

B - - - - - + - - - - - + - - - - - + - - - - - E

NORM REMAIN 10:00 HI–FI COUNT –1:23:45

1 Channel and auxiliary input (“L-1” and “F-1”) 2 Day and clock time 3 STEREO program indication : Z pg. 27 4 SAP (Second Audio Program) indication :

Z pg. 27

5 Audio monitor indications : Z pg. 23, 42 6 Timer warning display : Z pg. 36

TO START SOON

(CANCEL)

7 VCR operation mode indication 8 Tape speed indication 9 Cassette indication 0 Tape position indicator : Z pg. 22 ! Index no. indication : Z pg. 23 @ Tape remaining time : Z pg. 22, 26 # Time counter : Z pg. 22, 26

INDEX 1

INDEX (cont.)

Remote

MBRSET

2 3

4 5

6 7

9 0

! @ #

$ %

The glow-in-the-dark buttons shown in white on the illustration above are helpful when using the Remote in darkened rooms.

Buttons with a small dot on the left side of the name can also be used to operate your TV while holding down TV on the Remote. (Z pg. 52).

CABLE/

DBS

TV/VCR

A/B

A. MONITOR

POWER

DISPLAY

123 456

DBS

DAILY(M-F)

C. RESET

CANCEL

START STOP DATE

EXPRESS PROGRAMMING

PROG

CHECK

REW

REC

SHUTTLE

–

MULTI BRAND

REMOTE CONTROL UNIT

WEEKLY

AUX

TIMER

SP/EP SKIP SEARCH

PLAY

STOP

PAUSE

PLUS

–

& * (

) q w e r t

y u

i o

p Q W

1 CABLE/DBS button : Z pg. 53, 54 2 TV button: Z pg. 52 3 TV/VCR button : Z pg. 25, 26, 52 4 REVIEW button : Z pg. 24 5 Number buttons : Z pg. 25, 30, 33 6 DBS button : Z pg. 35 7 CANCEL button : Z pg. 31, 37

C. (Counter) RESET button : Z pg. 22, 26

8 STOP +/– button : Z pg. 31, 34 9 START +/– button : Z pg. 34 0 PROG. (Program) button : Z pg. 30, 34 ! PROG. CHECK button : Z pg. 37 @ REW ( 1 ) button : Z pg. 21, 25, 28 # REC ( ¶ ) button : Z pg. 25, 26 $ STOP ( 7 ) button : Z pg. 21, 25 % MENU button ^ SHUTTLE PLUS %ﬁ buttons

TV CH +/– buttons : Z pg. 52, 53, 54

& MBR SET button : Z pg. 52, 53, 54

A/B button : Z pg. 55

* POWER button : Z pg. 21, 25 ( A. (Audio) MONITOR button : Z pg. 23

(TV Muting) button : Z pg. 52

) DISPLAY button : Z pg. 22, 26 q DAILY (M-F) button : Z pg. 31, 35 w WEEKLY button : Z pg. 31, 35 e AUX button : Z pg. 47, 48, 49, 51 r TIMER button : Z pg. 31, 35, 37 t DATE +/– button : Z pg. 34 y CH +/– button : Z pg. 25, 34 u SKIP SEARCH button : Z pg. 29 i SP/EP button : Z pg. 25, 31, 35 o PLAY ( 3 ) button: Z pg. 21, 25 p FF ( ¡ ) button: Z pg. 21, 25, 28 Q PAUSE ( 8 ) button: Z pg. 25, 29 W OK button

ENTER button : Z pg. 52, 53, 54 OSD button : Z pg. 27

E SHUTTLE PLUS 4 ¢ (@ #) button

: Z pg. 29 TV VOL +/– button : Z pg. 52

How to use the Remote

Before use, insert two AA size batteries into the Remote with the polarity (ª and ·) matched correctly as indicated on the battery compartment or on the lid.

The Remote can operate most of your VCR’s functions, as well as basic functions of TV sets, cable boxes and DBS receivers.

● Point the Remote toward the remote sensor on the target component.

● The maximum operating distance of the remote control is about 8 m.

NOTE:

If the Remote does not work properly, remove its batteries, wait for a few seconds, replace the batteries and then try again.

SPECIFICATIONS

GENERAL

Power requirement : AC 120 V` , 60 Hz Power consumption

Power on : 20 W Power off : 2.5 W

Temperature

Operating : 5°C to 40°C (41°F to 104°F)

Storage : –20°C to 60°C (–4°F to140°F) Operating position : Horizontal only Dimensions (W x H x D) : 400 mm x 94 mm x 283 mm Weight : 3.4 kg Format : S-VHS/VHS NTSC standard Maximum recording time

SP : 210 min. with ST-210 video

cassette

EP : 630 min. with ST-210 video

cassette

VIDEO/AUDIO

Signal system : NTSC-type color signal and

EIA monochrome signal,

525␣ lines/60␣ fields Recording/ Playback system : DA-4 (Double Azimuth) head

helical scan system Signal-to-noise ratio : 45 dB Horizontal resolution

VHS : 230 lines S-VHS : 400 lines

Frequency range

Normal audio : 70 Hz to 10,000 Hz Hi-Fi audio : 20 Hz to 20,000 Hz

Input/Output : RCA connectors

(IN x 2, OUT x 1)

S-video connectors

(IN x 2, OUT x 1)

TUNER

Tuning system : Frequency-synthesized tuner Channel coverage

VHF : Channels 2–13 UHF : Channels 14–69 CATV : 113 Channels

RF output : Channel 3 or 4 (switchable;

preset to Channel 3 when

shipped) 75 ohms,

unbalanced

TIMER

Clock reference : Quartz Program capacity : 1-year programmable timer/

8 programs

Memory backup time : Approx. 3 min.

ACCESSORIES

Provided accessories : Infrared remote control unit,

“AA” battery x 2, S-video cable (4-pin), RF cable (F-type), Audio/video cable, Controller

Specifications shown are for SP mode unless specified otherwise. E. & O.E. Design and specifications subject to change without notice.

Usable cassettes

Full-Size VHS T-30 (ST-30**) T-60 (ST-60**) T-90 T-120 (ST-120**) T-160 (ST-160**) ST-210**

Compact VHS* TC-20 (ST-C20**) TC-30 (ST-C30**) TC-40 (ST-C40**)

* Compact VHS camcorder recordings can be

played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.

** This VCR can record on regular VHS and Super

VHS cassettes. While only VHS signals can be recorded on regular VHS cassettes and Super VHS signals can be recorded and played back using Super VHS cassettes.

By using the S-VHS ET function, it is possible to record and play back with S-VHS picture quality on VHS cassettes on this VCR.

, both VHS

FOR SERVICING (Only in U.S.A.)

HOW TO LOCATE YOUR JVC SERVICE CENTER

TOLL FREE: 1-800-537-5722

Dear customer,

In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the unit. In the event that repair is necessary , or for the address nearest your location within the Continental United States, please call 1-800-537-5722 for your nearest authorized servicer or visit our website at www.JVC.com. Remember to retain your Bill of Sale for Warranty Service.

DIVISION OF JVC AMERICAS CORP.

Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level performance for which JVC is world famous. The JVC service and engineering organization stands behind our products.

JVC SERVICE & ENGINEERING COMPANY OF AMERICA

http://www.jvc.com

— JVC

JVC SERVICE & ENGINEERING

COMPANY OF AMERICA

NATIONAL HEADQUARTERS

DIVISION OF JVC AMERICAS CORP.

10 New Maple Avenue

Pine Brook, NJ 07058-9641

ACCESSORIES

To purchase accessories for your JVC product, you may contact your local JVC Dealer. From the 48 Continental United States call toll free: 1-800-882-2345 or on the web at www.JVC.com

Don't service the product yourself.

CAUTION

To prevent electrical shock, do not open the cabinet. There are no user serviceable parts inside. Please refer to qualified service personnel for repairs.

WARRANTY (Only in U.S.A.)

LIMITED WARRANTY CONSUMER VIDEO 1-90

JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONL Y T O THE ORIGINAL PURCHASER A T RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below. ("The Warranty Period")

PARTS LABOR

1 YR 90 DAYS

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO.

WHAT WE WILL DO:

If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered on an in-home basis.

WHAT YOU MUST DO FOR WARRANTY SERVICE:

Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800) 537-5722.

If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number.

If you have any questions concerning your JVC Product, please contact our Customer Relations Department.

WHAT IS NOT COVERED:

This limited warranty provided by JVC does not cover:

1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with, defaced or removed;

2. Initial installation and installation and removal for repair;

3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;

4. Damage that occurs in shipment, due to act of God, and cosmetic damage;

5. Signal reception problems and failures due to line power surge;

6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;

7. Accessories;

8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase)

There are no other express warranties except as listed above. THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS

LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN. JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER

DAMAGES, WHETHER DIRECT , INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

JVC COMPANY OF AMERICA 1700 Valley Road DIVISION OF JVC AMERICAS CORP. Wayne, New Jersey 07470

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.

For customer use:

Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this information for future reference.

Model No.: Serial No.: Purchase date: Name of dealer:

HR-S7900U

VICTOR COMPANY OF JAPAN, LIMITED

U/U(C)

Printed in Malaysia 0301 IYV

*ID*

JVC HR-S7900U User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

CONTENTS

INSTALLING YOUR NEW VCR

INITIAL SETTINGS

BASIC PLAYBACK AND RECORDING

Special Effect Playback

TIMER RECORDING

OTHER USEFUL FUNCTIONS

EDITING

MULTI-BRAND REMOTE CONTROL

TROUBLESHOOTING

INDEX

SPECIFICATIONS

FOR SERVICING (Only in U.S.A.)

WARRANTY (Only in U.S.A.)