Jenn-Air JDS8860 User Manual 2
JENN-AIR® DUAL FUEL SLIDE-IN RANGE
CUISINIÈRE ENCASTRABLE À
DOUBLE COMBUSTIBLE JENN-AIR
®
Use & Care Guide
For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:
1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.
In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.
Guide d’utilisation et d’entretien
Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web à www.jennair.ca.
Table of Contents/Table des matières ...................2
Model/Modèle JDS8860
W10432287A
TABLE OF CONTENTS
RANGE SAFETY .............................................................................3
The Anti-Tip Bracket ....................................................................4
COOKTOP USE ..............................................................................6
Cooktop Controls.........................................................................6
Power Failure................................................................................7
Sealed Surface Burners ...............................................................7
Home Canning .............................................................................8
Cookware .....................................................................................8
ELECTRONIC OVEN CONTROLS.................................................9
Electronic Control Pads ...............................................................9
Oven Display ................................................................................9
Quickset Pads..............................................................................9
Cancel ..........................................................................................9
Clock ............................................................................................9
Timers.........................................................................................10
Locking the Oven Control and Oven Door ................................10
Oven Light ..................................................................................10
Setup ..........................................................................................10
OVEN USE.....................................................................................13
Aluminum Foil.............................................................................13
Positioning Racks and Bakeware ..............................................13
Bakeware....................................................................................14
Meat Thermometer.....................................................................14
Oven Vent...................................................................................14
Bake............................................................................................14
Broil.............................................................................................15
Convection Cooking...................................................................15
Convect Bake (on some models)...............................................16
Convect Roast (on some models)..............................................16
Convect Pastry...........................................................................17
Rapid Preheat.............................................................................17
More Options..............................................................................17
Warming Drawer.........................................................................18
Meat Probe.................................................................................19
Drying (on some models) ...........................................................20
Thaw and Serve (on some models)............................................21
Favorites.....................................................................................22
RANGE CARE ...............................................................................23
Self-Cleaning Cycle (on some models)......................................23
General Cleaning........................................................................24
Oven Lights ................................................................................25
Warming Drawer (on some models)...........................................25
Oven Door ..................................................................................26
TROUBLESHOOTING ..................................................................26
ASSISTANCE OR SERVICE.........................................................28
In the U.S.A. ...............................................................................28
Accessories ................................................................................28
In Canada ...................................................................................28
WARRANTY ..................................................................................29
TABLE DES MATIÈRES
SÉCURITÉ DE LA CUISINIÈRE...................................................31
La bride antibasculement...........................................................32
UTILISATION DE LA TABLE DE CUISSON................................34
Commandes de la table de cuisson ..........................................35
Panne de courant.......................................................................36
Brûleurs de surface scellés........................................................36
Préparation de conserves à la maison ......................................37
Ustensiles de cuisson ................................................................37
COMMANDES ÉLECTRONIQUES DU FOUR ............................37
Touches de commande électroniques ......................................38
Afficheur du four.........................................................................38
Touches de réglage rapide ........................................................38
Annulation...................................................................................38
Horloge.......................................................................................38
Minuteries...................................................................................38
Verrouillage du module de commande du four et
de la porte du four......................................................................39
Lampe du four............................................................................39
Réglage ......................................................................................39
UTILISATION DU FOUR...............................................................42
Papier d’aluminium ....................................................................42
Positionnement des grilles et des ustensiles
de cuisson au four......................................................................42
Ustensiles de cuisson au four....................................................43
Thermomètre à viande ...............................................................44
Évent du four ..............................................................................44
Cuisson au four ..........................................................................44
Cuisson au gril............................................................................44
Cuisson par convection .............................................................45
Cuisson au four par convection.................................................45
Rôtissage par convection ..........................................................46
Cuisson de pâtisseries par convection......................................46
Préchauffage rapide...................................................................47
Plus d’options.............................................................................47
Tiroir-réchaud.............................................................................48
Sonde thermométrique ..............................................................49
Séchage (sur certains modèles).................................................50
Décongeler et servir (sur certains modèles)...............................52
Recettes favorites.......................................................................53
ENTRETIEN DE LA CUISINIÈRE.................................................54
Programme d’autonettoyage (sur certains modèles) ................54
Nettoyage général ......................................................................55
Lampes du four ..........................................................................56
Tiroir-réchaud.............................................................................56
Porte du four...............................................................................57
DÉPANNAGE.................................................................................57
ASSISTANCE OU SERVICE.........................................................59
Accessoires ................................................................................59
Au Canada..................................................................................59
GARANTIE.....................................................................................59
2
RANGE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
follow
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
3
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the
anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
Anti-Tip
Bracket
Range Foot
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
4
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
persons, or damage when using the range, follow basic
precautions, including the following:
■
WARNING:
RANGE, THE RANGE MUST BE SECURED BY PROPERLY
INSTALLED ANTI-TIP DEVICES. TO CHECK IF THE DEVICES
ARE INSTALLED PROPERLY, SLIDE RANGE FORWARD,
LOOK FOR ANTI-TIP BRACKET SECURELY ATTACHED TO
FLOOR OR WALL, AND SLIDE RANGE BACK SO REAR
RANGE FOOT IS UNDER ANTI-TIP BRACKET.
■
WARNING:
heat or warm the room. Doing so may result in carbon monoxide
poisoning and overheating of the oven.
■
WARNING:
oven bottom or cover an entire rack with materials such as
aluminum foil. Doing so blocks air flow through the oven and
may cause carbon monoxide poisoning. Aluminum foil linings
may also trap heat, causing a fire hazard.
■
CAUTION:
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be seriously
injured.
■ Do Not Leave Children Alone – Children should not be left alone
or unattended in area where the range is in use. They should
never be allowed to sit or stand on any part of the range.
■ Wear Proper Apparel – Loose-fitting or hanging garments
should never be worn while using the range.
■ User Servicing – Do not repair or replace any part of the range
unless specifically recommended in the manual. All other
servicing should be referred to a qualified technician.
■ Storage in or on the Range – Flammable materials should not
be stored in an oven or near surface units.
■ Do Not Use Water on Grease Fires – Smother fire or flame or
use dry chemical or foam-type extinguisher.
■ Use Only Dry Potholders – Moist or damp potholders on hot
surfaces may result in burns from steam. Do not let potholder
touch hot heating elements. Do not use a towel or other bulky
cloth.
■ DO NOT TOUCH SURFACE UNITS OR AREAS NEAR UNITS –
Surface units may be hot even though they are dark in color.
Areas near surface units may become hot enough to cause
burns. During and after use, do not touch, or let clothing or
other flammable materials contact surface units or areas near
units until they have had sufficient time to cool. Among those
areas are the cooktop and surfaces facing the cooktop.
■ Never Leave Surface Units Unattended at High Heat Settings –
Boilover causes smoking and greasy spillovers that may ignite.
■ Glazed Cooking Utensils – Only certain types of glass,
glass/ceramic, ceramic, earthenware, or other glazed utensils
are suitable for range-top service without breaking due to the
sudden change in temperature.
■ Utensil Handles Should Be Turned Inward and Not Extend Over
Adjacent Surface Units – To reduce the risk of burns, ignition of
flammable materials, and spillage due to unintentional contact
with the utensil, the handle of a utensil should be positioned so
that it is turned inward, and does not extend over adjacent
surface units.
To reduce the risk of fire, electrical shock, injury to
TO REDUCE THE RISK OF TIPPING OF THE
NEVER use this appliance as a space heater to
NEVER cover any slots, holes or passages in the
Do not store items of interest to children in
■ Clean Cooktop With Caution – If a wet sponge or cloth
is used to wipe spills on a hot cooking area, be careful
to avoid steam burn. Some cleaners can produce
noxious fumes if applied to a hot surface.
■ Use Care When Opening Door – Let hot air or steam
escape before removing or replacing food.
■ Do Not Heat Unopened Food Containers – Build-up of
pressure may cause container to burst and result in
injury.
■ Keep Oven Vent Ducts Unobstructed.
■ Placement of Oven Racks – Always place oven racks in
desired location while oven is cool. If rack must be
moved while oven is hot, do not let potholder contact
hot heating element in oven.
■ DO NOT TOUCH HEATING ELEMENTS OR INTERIOR
SURFACES OF OVEN – Heating elements may be hot
even though they are dark in color. Interior surfaces of
an oven become hot enough to cause burns. During
and after use, do not touch, or let clothing or other
flammable materials contact heating elements or interior
surfaces of oven until they have had sufficient time to
cool. Other surfaces of the appliance may become hot
enough to cause burns – among these surfaces are
oven vent openings and surfaces near these openings,
oven doors, and windows of oven doors.
■ Proper Installation – The range, when installed, must be
electrically grounded in accordance with local codes or,
in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70. In Canada, the range
must be electrically grounded in accordance with
Canadian Electrical Code. Be sure the range is properly
installed and grounded by a qualified technician.
■ Disconnect the electrical supply before servicing the
appliance.
■ Injuries may result from the misuse of appliance doors
or drawers such as stepping, leaning, or sitting on the
doors or drawers.
■ Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
■ Top burner flame size should be adjusted so it does not
extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
■ Do Not Clean Door Gasket – The door gasket is
essential for a good seal. Care should be taken not to
rub, damage, or move the gasket.
■ Do Not Use Oven Cleaners – No commercial oven
cleaner or oven liner protective coating of any kind
should be used in or around any part of the oven.
■ Clean Only Parts Listed in Manual.
■ Before Self-Cleaning the Oven – Remove broiler pan
and other utensils. Wipe off all excessive spillage before
initiating the cleaning cycle.
For units with ventilating hood –
■ Clean Ventilating Hoods Frequently – Grease should not
be allowed to accumulate on hood or filter.
■ When flambéing foods under the hood, turn the fan on.
SAVE THESE INSTRUCTIONS
5
COOKTOP USE
This manual covers several different models. The range you have purchased may have some or all of the items listed. The locations and
appearances of the features shown here may not match those of your model.
A
B C D
A. Surface burner locator
B. Left front control knob
C. Left rear control knob
Cooktop Controls
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
IMPORTANT: Your range is factory-set for use with Natural gas. If
you wish to use LP gas, an LP Gas Conversion Kit is included
with your new range. See the “Gas Conversions” section of the
Installation Instructions for details on making this conversion.
Electric igniters automatically light the surface burners when
control knobs are turned on.
Before setting a control knob, place filled cookware on the grate.
Do not operate a burner while using empty cookware or without
any cookware on the grate.
NOTE: Visually check that the burner has lit. If the burner does
not ignite, listen for a clicking sound. If you do not hear the igniter
click, turn the burner off. Check for a tripped circuit breaker or
blown household fuse.
Check that the control knob is pressed completely down on the
valve shaft. If the spark igniter still does not operate, call a trained
repair specialist.
E F
D. Electronic oven control
E. Right rear control knob
F. Right front control knob
To S et :
1. Push in and turn knob counterclockwise to light the burner.
All four surface burners will click. Only the burner that has
been turned on will produce a flame.
IMPORTANT: Each surface burner is equipped to provide
automatic reignition if the flame should somehow get blown
out.
2. Turn knob anywhere between HIGH and LOW. Use the
following chart as a guide when setting heat levels.
SETTING RECOMMENDED USE
HIGH
Medium
between High and
Low
LOW
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
■ Start food cooking.
■ Bring liquid to a boil.
■ Hold a rapid boil.
■ Quickly brown or sear food.
■ Fry or sauté foods.
■ Cook soups, sauces and gravies.
■ Stew or steam foods.
■ Keep food warm.
■ Simmer.
6
Cooktop Burners
D
A
High Performance Burner
There is 1 high speed burner on the cooktop, located in the right
front position. This burner offers higher speed cooking that can
be used to quickly bring water to a boil and for large-quantity
cooking.
Simmer Burners
Simmer burners are located in the left or right rear positions. The
simmer burner offers a lower Btu/h flame for delicate sauces or
melting chocolate.
Dual Ring Burner
There is 1 dual ring burner on the cooktop, located in the left front
position. To operate, push in on the control knob and turn
counterclockwise to light the burner. Continue turning until the
desired setting is reached. The lighting sequence is: inner burner
on High, then inner burner on Low, then both rings on High, then
both rings on Low.
Power Failure
Surface Burners
In case of prolonged power failure, the surface burners can be lit
manually. Hold a lit match near a burner and turn knob
counterclockwise to ignite. After burner lights, turn knob to
desired setting.
Sealed Surface Burners
A
B
Burner cap: Always keep the burner cap in place when using a
surface burner. A clean burner cap will help avoid poor ignition
and uneven flames. Always clean the burner cap after a spillover
and routinely remove and clean the caps according to the
“General Cleaning” section.
Gas tube opening: Gas must flow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil
and do not allow spills, food, cleaning agents or any other
material to enter the gas tube opening. Keep spillovers out of the
gas tube by always using a burner cap.
A
B
A. 1-1¹⁄₂" (25-38 mm)
B. Burner ports
Burner ports: Check burner flames occasionally for proper size
and shape as shown in the previous illustration. A good flame is
blue in color, not yellow. Keep this area free of soil and do not
allow spills, food, cleaning agents or any other material to enter
the burner ports.
To C le an:
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Do not use oven cleaners, bleach
or rust removers.
1. Remove the burner cap from the burner base and clean
according to “General Cleaning” section.
2. Clean the gas tube opening with a damp cloth.
3. Clean clogged burner ports with a straight pin as shown. Do
not enlarge or distort the port. Do not use a wooden
toothpick. If the burner needs to be adjusted, contact a
trained repair specialist.
E
C
A. Burner cap
B. Burner base
C. Alignment pins
D. Igniter
E. Gas tube opening
IMPORTANT: Do not obstruct the flow of combustion and
ventilation air around the burner grate edges.
4. Replace the burner cap, making sure the alignment pins are
properly aligned with the burner cap.
B
A. Incorrect
B. Correct
5. Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
7
Home Canning
When canning for long periods, alternate the use of surface
burners between batches. This allows time for the most recently
used areas to cool.
■ Center the canner on the grate above the burner.
■ Do not place canner on 2 surface burners at the same time.
■ For more information, contact your local agricultural
department. Companies that manufacture home canning
products can also offer assistance.
Cookware
IMPORTANT: Do not leave empty cookware on a hot surface
cooking area, element or surface burner.
Ideal cookware should have a flat bottom, straight sides and a
well-fitting lid, and the material should be of medium-to-heavy
thickness.
Rough finishes may scratch the cooktop or grates. Aluminum and
copper may be used as a core or base in cookware. However,
when used as a base they can leave permanent marks on the
cooktop or grates.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A nonstick finish has
the same characteristics as its base material. For example,
aluminum cookware with a nonstick finish will take on the
properties of aluminum.
Cookware with nonstick surfaces should not be used under the
broiler.
Use the following chart as a guide for cookware material
characteristics.
COOKWARE CHARACTERISTICS
Aluminum ■ Heats quickly and evenly.
■ Suitable for all types of cooking.
■ Medium or heavy thickness is best for
most cooking tasks.
Cast iron ■ Heats slowly and evenly.
■ Good for browning and frying.
■ Maintains heat for slow cooking.
Ceramic or
Ceramic glass
■ Follow manufacturer’s instructions.
■ Heats slowly, but unevenly.
■ Ideal results on low to medium heat
settings.
Copper
Earthenware
Porcelain
■ Heats very quickly and evenly.
■ Follow manufacturer’s instructions.
■ Use on low heat settings.
■ See stainless steel or cast iron.
enamel-onsteel or cast
iron
Stainless steel
■ Heats quickly, but unevenly.
■ A core or base of aluminum or copper
on stainless steel provides even
heating.
8
JDS8860
ELECTRONIC OVEN CONTROLS
BAB
CD E
H
I
N
A. Bake
B. Favorites
C. Setup
D. Timer 1
E. Display
MLKJ
F. Ti m er 2
G. Number pads
H. Broil
I. Convect
J. Rapid preheat
Electronic Control Pads
When pressing any control pad function on the Electronic Oven
Control, use the pad of your finger to press the desired function.
Hold down the pad a few seconds, or until the desired function
appears in the display.
Oven Display
When power is supplied to the range or after a power
interruption, “12:00” and “POWER LOSS” will be displayed.
Press CANCEL to clear “POWER LOSS.”
When the oven is in use, the display shows the time of day,
temperature, and oven setting.
When the oven is not is use, the display shows the time of day.
When using the Timer, for settings of 1 to 59 minutes, the display
will count down in minutes and seconds. For settings of 1 hour or
more, the display will count down hours and minutes.
Quickset Pads
Quickset pads are located on each side of the display window
and are used to select the desired function or option in the
display window. To select the option or function, press the
Quickset pad next to the word.
If you need to back out of a function or option in the display,
press the BACK pad. When your programming is complete, press
the ENTER pad or wait 4 seconds and the function will start
automatically.
Up arrows indicate additional screens with additional options.
Press the QUICKSET pads next to the arrows to scroll through
the display.
IMPORTANT: Four seconds after entering the function, option,
number or letter, the function will automatically be entered. If
more than 30 seconds elapse between steps in programming,
the function will be canceled and the display will return to the
previous display.
O
K. More options
L. Clean
M. Quickset pads
N. Warm drawer
O. Oven light
F
MP
P. Cancel
Q. Back
R. Lock
S. Enter
G
R
Q
S
Cancel
The CANCEL button stops any function except the Clock, Timer
and Control Lock. When you press the CANCEL button, the
display will show the time of day, or the time remaining if the
TIMER is being used.
Clock
To Set Clock:
1. Press SETUP.
2. Select CLOCK using the left Quickset pad.
3. Select TIME using the left Quickset pad.
4. Enter the time using the number pads.
5. Press ENTER on the number pads.
6. Select AM or PM in 12-hour mode. (For 24-hour clock, see
following.)
7. To exit the Setup mode, press SETUP.
Entering the Day of the Week:
1. Press SETUP.
2. Select CLOCK using the left Quickset pad.
3. Press the right Quickset pad to scroll until DAY is displayed.
4. Select DAY using the left Quickset pad.
5. Use right Quickset pad to scroll through the days.
6. Select the day desired using the left Quickset pad.
7. To exit the Setup mode, press SETUP.
To Set the Clock for a 12- or 24-Hour Format:
The clock can be set to display time in either a 12-hour or
24-hour format.
1. Press SETUP.
2. Select CLOCK using the left Quickset pad.
3. Use right Quickset pad to scroll to 12/24 HOUR.
4. Press the left Quickset pad to select 12/24 HOUR.
5. Select 12 HR or 24 HR using the right or left Quickset pad.
6. To exit Setup mode, press SETUP.
9
Activating and Canceling the Clock/Day of Week Display:
1. Press SETUP.
2. Select CLOCK using the left Quickset pad.
3. Press the right Quickset pad to scroll until DISABLE is
displayed.
4. Select DISABLE using the left Quickset pad.
5. Select TIME using the left Quickset pad.
6. Select ON or OFF using the right or left Quickset pad to turn
the clock display On or Off.
Day of the week:
7. Use right Quickset pad to scroll to DAY.
8. Select DAY using the left Quickset pad.
9. Select ON or OFF using the right or left Quickset pad to turn
the Day of the Week display On or Off.
10. To exit the Setup mode, press SETUP.
Timers
Setting the Timers (Timer 1 or Timer 2):
1. Press TIMER 1 or TIMER 2.
2. Press one of the displayed times using the Quickset pads, or
press the number pads to enter the desired time.
IMPORTANT: Each press of the displayed time choices adds
additional time. For example, pressing “10 MIN” three times
provides 30 minutes on the timer (0:30).
3. Press ENTER (located on the number pad).
Changing the Amount of Time Entered Once the Timer Starts:
1. Press TIMER 1 or TIMER 2 once.
2. Press the displayed times on the Quickset pads repeatedly
until the desired time is entered.
OR
Press the number pads to enter the new desired time.
3. Press Enter pad.
Canceling the Timer:
1. Press TIMER 1 or TIMER 2 twice.
If Both Timers Are Active:
If the desired Timer is already in the foreground, press once for
edit mode and twice to cancel the Timer. If the desired Timer is
not in the foreground, follow these steps:
1. Press the desired TIMER pad once. The selected Timer will
come to the foreground.
2. Press TIMER a second time to access the edit mode in order
to make changes.
3. Pressing TIMER a third time will cancel the Timer.
Changing the Timer Beeps:
The signal beeps for TIMER 1 and TIMER 2 can be changed. The
options available are 2 beeps every 30 seconds, 2 beeps every
60 seconds or 1 beep only. The default setting is 1 beep.
1. Press SETUP.
2. Use right Quickset pad to scroll to TONES.
3. Select TONES using the left Quickset pad.
4. Use right Quickset pad to scroll to TIMER TONES.
5. Select TIMER TONES using the left Quickset pad.
6. Use right Quickset pad to scroll to the desired timer beep
format (2-30 SEC, 2-60 SEC or 1 BEEP).
7. Select the desired timer beep using the left Quickset pad.
8. Press SETUP to exit Setup mode.
Locking the Oven Control and Oven Door
The lock feature shuts down the control pads (buttons) and locks
the oven door to avoid unintended use of the oven.
The lock feature is preset unlocked, but can be locked.
If the oven is currently in use, the controls and oven door cannot
be locked.
To Lock the Oven Control and Oven Door:
Press and hold BACK and ENTER for 3 seconds or until
“CONTROL LOCKED” appears in the display.
To Unlock the Oven Control and Oven Door:
Press and hold BACK and ENTER for 3 seconds. “UNLOCKING
DOOR” will appear in the display when the control and door are
unlocking.
Oven Light
The oven light automatically comes on when the door is opened.
When the door is closed, press the OVEN LIGHT pad to turn the
oven light on and off. A beep will sound every time the Oven Light
pad is pressed. If the oven light is on when the door is opened,
the light will go off when the door is closed.
Setup
1. Press SETUP to begin.
2. Use right Quickset pad to scroll through Setup options.
3. Select the desired option by pressing the Quickset pads.
NOTE: To back out of a screen without making any changes,
press the Setup pad. The display will return to the time of day.
Clock
See the “Clock” section for more details. Use the Clock option to:
■ Set the time of day.
■ Set day of week.
■ Select AM or PM (12-hour mode only). AM or PM will not
show with the time of day in the display.
■ Choose a 12- or 24-hour clock display.
■ Disable the clock display.
Language
The language of the screens in the display window can be set to
English, French or Spanish.
To change the display language from English:
1. Press SETUP.
2. Use right Quickset pad to scroll to LANGUAGE.
3. Select LANGUAGE using the left Quickset pad.
4. Use right Quickset pad to scroll to the desired language.
5. Select the desired language using the left Quickset pad.
6. Press SETUP to exit the Setup menu.
10
Auto Convect Conversion (on some models)
The oven comes from the factory set for Auto Convect
conversion. Auto Convect Conversion automatically reduces the
set temperature by 25°F for Convect Bake and Convect Pastry.
For Convect Roast, the control will alert you at 75% of the
programmed roasting time to check foods for doneness. Convect
roast temperatures are not reduced.
NOTES:
■ When using Convect Bake and Convect Pastry with the Auto
Convect Conversion option turned off, reduce the set
temperature by 25°F.
■ If Convect Roasting with the Auto Convect conversion option
turned off, you will not be required to program a cooking time.
Check food at 75% of the conventional time.
To deactivate Auto Convect conversion:
1. Press SETUP.
2. Use right Quickset pad to scroll to AUTO CONVECT.
3. Select AUTO CONVECT using the left Quickset pad.
4. Select OFF using the Quickset pad.
5. Press SETUP to exit the Setup menu.
To reactivate Auto Convect conversion:
1. Press SETUP.
2. Use right Quickset pad to scroll to AUTO CONVECT.
3. Select AUTO CONVECT using the left Quickset pad.
4. Select ON using the Quickset pad.
5. Press SETUP to exit the Setup menu.
C/F (Celsius/Fahrenheit)
The displayed temperature scale can be changed from
Fahrenheit to Celsius.
To change the scale:
1. Press SETUP.
2. Use right Quickset pad to scroll to C/F.
3. Select C/F using the left Quickset pad.
4.
Select the desired temperature scale using the Quickset pads.
5. Press SETUP to exit the Setup menu.
Sabbath Mode
The oven is set to shut off after 12 hours if you unintentionally
leave it on. The Sabbath Mode overrides the 12-hour shutoff and
can either be set to come on automatically or can be set
manually as desired.
Only Bake or Cook/Hold Bake will operate when the oven is in
Sabbath Mode. All other functions are invalid. If a function other
than Bake or Cook/Hold Bake is in operation when Sabbath
Mode starts, the function will be canceled.
■ The oven must be idle to program Sabbath Mode.
■ Sabbath Mode cannot be turned on if the keypads are locked
out or when the door is locked.
■ If the oven is baking when Auto Sabbath Mode starts, there
will be no audible beeps.
■ All prompts, messages and beeps are deactivated when the
Sabbath Mode is active.
■ If the oven light is desired while in Sabbath Mode, it must be
turned on before the Sabbath Mode is set.
■ The self-clean cycle and automatic door lock do not operate
during the Sabbath Mode.
■ The Bake temperature can be changed during an Active
Sabbath Mode. Simply press the Bake pad and then enter
the desired temperature using the Quickset pads.
■ Pressing the Cancel pad will cancel a Bake cycle; however,
the control will stay in the Sabbath Mode.
■ The day of the week and AM/PM must be set for Sabbath
Auto Mode to operate correctly.
To activate Sabbath mode:
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
1. Press SETUP.
2. Use right Quickset pad to scroll to SABBATH.
3. Select SABBATH using the left Quickset pad.
4. Select AUTO or MANUAL.
AUTO will automatically prompt you to enter a Bake
temperature on Friday at 2 p.m. and stay in Sabbath mode for
33 hours. “SABBATH” and “SABBATH ENABLE” appear in the
display for 90 minutes. If Bake or Cook/Hold Bake are desired
during Sabbath Mode, they must be programmed during this
90-minute period before AUTO Sabbath Mode is active.
MANUAL sets the oven to Sabbath Mode for 72 hours.
“SABBATH” and “SABBATH ENABLE” appear in the display
for 5 minutes. If Bake or Cook/Hold Bake are desired during
Sabbath Mode, they must be programmed during this
5-minute period before the MANUAL Sabbath Mode is active.
5. Select ON or OFF.
To cancel Sabbath mode:
1. Press CANCEL.
2. Press and hold SETUP for 5 seconds.
Temp Adjust
Oven temperatures are tested at the factory. It is normal to notice
some baking time or browning differences between a new oven
and an old one. As ovens get older, the oven temperature can
shift.
You may adjust the oven temperature if you think the oven is not
baking or browning correctly. To decide how much to change the
temperature, set the oven temperature 25°F higher or lower than
the temperature in your recipes, then bake. The results of the first
bake should give you an idea of how much to adjust the
temperature.
To adjust the oven temperature:
1. Press SETUP.
2. Use right Quickset pad to scroll to TEMP ADJUST.
3. Select TEMP ADJUST using the left Quickset pad.
4.
Enter the desired temperature change using the number pads.
5. Use the Quickset pads to select “+/-” to indicate an increase
or decrease in temperature. The temperature change is
displayed at the top of the window.
6. Press ENTER or wait 3 seconds to accept the change.
7. Press SETUP to exit the menu.
The oven temperature does not need to be readjusted if there is a
power failure or interruption.
Broiling and cleaning temperatures cannot be adjusted.
11
208/240V
For improved results when using Bake, the oven can be set from
240V to 208V if your household is on 208V.
To set the oven to 208V:
1. Press SETUP.
2. Use right Quickset pad to scroll to 208/240V.
3. Select 208/240V using the left Quickset pad.
4. Select 208V or 240V using the Quickset pads.
5. Press SETUP to exit the menu.
4. Use right Quickset pad to scroll to VOLUME.
5. Select VOLUME using the left Quickset pad.
6. Use right Quickset pad to scroll and select:
HIGH for the highest volume.
OR
MEDIUM for medium volume.
OR
LOW for the lowest volume.
7. Select the desired volume using the left Quickset pad.
8. Press SETUP to exit.
Tones (beeps)
The number of beeps heard at the end of cooking and at the end
of timer operation and their volume can be adjusted.
To change the beeps at the end of cooking:
1. Press SETUP.
2. Use right Quickset pad to scroll to TONES.
3. Select TONES using the left Quickset pad.
4. Use right Quickset pad to scroll to COOK TONE.
5. Select COOK TONE using the left Quickset pad.
6. Use the right Quickset pad to scroll and select:
1-30 SEC to hear 1 beep every 30 seconds.
OR
1-60 SEC to hear 1 beep every 60 seconds.
OR
1 BEEP to hear 1 beep only at the end of cooking.
7. Select the desired beep using the left Quickset pad.
8. Press SETUP to exit.
To change the timer beeps:
1. Press SETUP.
2. Use right Quickset pad to scroll to TONES.
3. Select TONES using the left Quickset pad.
4. Use right Quickset pad to scroll to TIMERS TONES.
5. Select TIMERS TONES using the left Quickset pad.
6. Use the right Quickset pad to scroll and select:
1-30 SEC to hear 1 beep every 30 seconds.
OR
1-60 SEC to hear 1 beep every 60 seconds.
OR
1 BEEP to hear 1 beep only at the end of cooking.
7. Select the desired beep using the left Quickset pad.
8. Press SETUP to exit.
To change the volume of the beeps:
1. Press SETUP.
2. Use right Quickset pad to scroll to TONES.
3. Select TONES using the left Quickset pad.
12 HR Shutoff
The oven will automatically turn off at the end of 12 hours if you
unintentionally leave it on.
To turn off this feature:
1. Press SETUP.
2. Use right Quickset pad to scroll to 12HR SHUTOFF.
3. Select 12HR SHUTOFF using the left Quickset pad.
4. Select ON or OFF using the Quickset pads.
5. Press SETUP to exit.
Energy Saver
To save energy, the display can be set to go dark if it is not being
used.
To set the Energy Saver feature:
1. Press SETUP.
2. Use right Quickset pad to scroll to ENERGY SAVER.
3. Select ENERGY SAVER using the left Quickset pad.
4. Select ON or OFF using the Quickset pads.
5. Press SETUP to exit.
Press any pad to “wake up” the display.
Service
This area of the oven control displays the Jenn-Air Customer
eXperience Center toll-free phone number.
1. Press SETUP.
2. Use right Quickset pad to scroll to SERVICE.
3. Select SERVICE using the left Quickset pad to display the
number.
4. Press SETUP to exit.
Demo
When Demo is selected, you will see a short presentation
highlighting the features of the range.
1. Press SETUP.
2. Use right Quickset pad to scroll to DEMO.
3. Select DEMO using the left Quickset pad.
4. Select ON using the left Quickset pad.
5. Press SETUP to exit.
12
OVEN USE
2
3
4
5
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and wellventilated room.
Aluminum Foil
IMPORTANT: To avoid permanent damage to the oven bottom
finish, do not line the oven bottom with any type of foil or liner.
■ For best cooking results, do not cover entire rack with foil
because air must be able to move freely.
■ To catch spills, place foil on rack below dish. Make sure foil is
at least ½" (1.3 cm) larger than the dish and that it is turned
up at the edges.
Positioning Racks and Bakeware
IMPORTANT: To avoid permanent damage to the porcelain
finish, do not place food or bakeware directly on the oven door or
bottom.
Racks
■ Depending on your model, 2 or 3 standard flat racks are
included.
■ Position racks before turning on the oven.
■ Do not position racks with bakeware on them.
■ Make sure racks are level.
Traditional Cooking
FOOD RACK POSITION
2-rack cooking and broiling. 5
2-rack baking and broiling. 4
Most baked goods on a cookie sheet or
jelly roll pan, layer cakes, fruit pies,
frozen convenience foods.
Roasting small cuts of meat,
casseroles, baking loaves of bread,
bundt cakes, custard pies, frozen pies
or 2-rack baking.
Large cuts of meat and poultry, dessert
souffles, angel food cake, or 2-rack
baking.
3
2
1
Multiple Rack Cooking
Two rack: Use rack positions 2 and 5 or 1 and 4.
Convection Cooking (on some models)
FUNCTION NUMBER OF
Convection baking or
roasting
Convection baking 2 2 and 4
Convection baking 3 1, 3 and 5
RACKS USED
11, 2 or 3
RACK
POSITION(S)
To Remove Oven Racks:
Pull rack out to the stop position, raise the front edge, and then
pull out.
To Replace Oven Racks:
Place rack on the rack support in the oven. Tilt the front edge up
slightly, and slide rack back until it clears the stop position. Lower
front and slide back into the oven.
Rack Positions
1
Multiple Rack Convection Cooking
Three rack (on some models): Use rack positions 1, 3 and 5.
NOTE: When convect baking on 2 or 3 racks, check foods at the
minimum suggested time to avoid overbrowning or overcooking.
Baking Layer Cakes on Two Racks
For best results when baking cakes on 2 racks with or without
convection (on some models), use racks 2 and 5. Place the cakes
on the rack as shown.
BAKEWARE
To cook food evenly, hot air must be able to circulate. Allow
2" (5.0 cm) of space around bakeware and oven walls. Use the
following chart as a guide.
NUMBER
OF PAN(S)
1 Center of rack.
2 Side by side or slightly staggered.
3 or 4 Opposite corners on each rack. Make sure that
POSITION ON RACK
no bakeware piece is directly over another.
13
Bakeware
The bakeware material affects cooking results. Follow
manufacturer’s recommendations and use the bakeware size
recommended in the recipe. Use the following chart as a guide.
BAKEWARE/
RECOMMENDATIONS
RESULTS
Light colored
aluminum
■ Light golden crusts
■ Even browning
Dark aluminum and
other bakeware with
dark, dull and/or
nonstick finish
■ Brown, crisp
crusts
Insulated cookie
sheets or baking
pans
■ Little or no bottom
■ Use temperature and time
recommended in recipe.
■ May need to reduce baking
temperatures slightly.
■ Use suggested baking time.
■ For pies, breads and casseroles,
use temperature recommended in
recipe.
■ Place rack in center of oven.
■ Place in the bottom third of oven.
■ May need to increase baking time.
browning
Stainless steel
■ Light, golden
■ May need to increase baking time.
crusts
■ Uneven browning
Stoneware/Baking
■ Follow manufacturer’s instructions.
stone
■ Crisp crusts
Ovenproof
glassware, ceramic
■ May need to reduce baking
temperatures slightly.
glass or ceramic
■ Brown, crisp
crusts
Meat Thermometer
A meat thermometer is not supplied with this appliance. Follow
manufacturer's directions for using a meat thermometer. On
models without a temperature probe, use a meat thermometer to
determine whether meat, poultry and fish are cooked to the
desired degree of doneness. The internal temperature, not
appearance, should be used to determine doneness.
Oven Vent
A
A. Oven vent
The oven vent releases hot air and moisture from the oven, and
should not be blocked or covered. Blocking or covering the vent
will cause poor air circulation, affecting cooking and cleaning
results. Do not set plastics, paper or other items that could melt
or burn near the oven vent.
Bake
The BAKE function is ideal for baking, roasting or heating foods.
During baking or roasting, the bake and broil elements will cycle
on and off in intervals to maintain oven temperature.
To B ak e:
Before baking, position racks according to the “Positioning
Racks and Bakeware” section.
For baking, allow the range to preheat before placing food in the
oven.
1. Press BAKE.
2. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads. The
temperature can be set from 170°F (80°C) to 550°F (288°C) in
5°F (1° in Celsius) increments.
3. Press ENTER to set.
After 3 seconds, the oven will begin to preheat. “BAKE” and
“PREHEAT” will appear in the display along with “100°”
(“38°” in Celsius) or the actual oven temperature, whichever is
higher.
The temperature in the display will increase in 1° increments
until the oven reaches the preset temperature. Allow about
15 minutes for the oven to preheat.
When the oven is preheated, the oven will beep and
“PREHEAT” will disappear from the display.
To change the oven temperature during cooking, press BAKE
and select a displayed temperature or use the number pads
to enter the desired temperature.
4. Press CANCEL when finished cooking. Remove food from
the oven.
14
Broil
Broiling uses direct radiant heat to cook food. Changing the
temperature when broiling allows more precise control when
cooking. The lower the temperature, the slower the cooking.
Thicker cuts and unevenly shaped pieces of meat, fish and
poultry may cook better at lower broiling temperatures.
■ For best results, use a broiler pan and grid. They are
designed to drain juices and help avoid spatter and smoke.
If you would like to purchase a Premium Broil Pan and
Roasting Rack, a set may be ordered. See “Assistance or
Service” section to order. Ask for Part Number W10123240.
■ For proper draining, do not cover the grid with foil. The
bottom of the pan may be lined with aluminum foil for easier
cleaning.
■ Trim excess fat to reduce spattering. Slit the remaining fat on
the edges to avoid curling.
■ Pull out oven rack to stop position before turning or removing
food. Use tongs to turn food to avoid the loss of juices. Very
thin cuts of fish, poultry or meat may not need to be turned.
■ After broiling, remove the pan from the oven when removing
the food. Drippings will bake on the pan if left in the heated
oven, making cleaning more difficult.
Before broiling, position rack according to the Broiling Chart.
Preheat broil for about 5 minutes. Position food on grid in the
broiler pan, then place it in the center of the oven rack. Close the
door to the broil stop position to ensure proper broiling
temperature.
BROILING CHART
For best results, place food 3" (7.0 cm) or more from the broil
element. Times are guidelines only and may need to be adjusted
for individual tastes. Recommended rack positions are numbered
from the bottom (1) to the top (5). For diagram, see the
“Positioning Racks and Bakeware” section.
FOOD RACK
POSITION
Steak
1" (2.5 cm) thick
medium
well-done
4
4
Ground meat patties
½" (1.3 cm) thick
well-done 4 10-12
Pork chops
1" (2.5 cm) thick
Bone-in
Boneless
4
4
Ham slice, precooked
1" (2.5 cm) thick
warm 4 12-16
Chicken
bone-in breasts
boneless, skinless breasts34
Seafood
Fish Steaks
1" (2.5 cm) thick
flaky
Lobster tails
3-4 oz (85-113 g) each
3 or 4
4
TOTAL
TIME
MIN.
18-20
18-22
25-28
20-28
LOW broil
20-33
12-15
10-14
7-10
To Broil:
Before broiling, position rack according to the Broiling Chart.
1. Press BROIL.
2. “HIGH” and “LOW” will be displayed.
Use the Quickset pads to select HIGH (550°F/290°C) for
normal broiling or LOW (450°F/230°C) for low-temperature
broiling.
OR
To select a broil temperature other than High or Low, enter
the desired temperature (300°F/149°C to 550°F/288°C) using
the number pads and press ENTER.
3. Press CANCEL when finished.
Convection Cooking
(on some models)
In a convection oven, the fan-circulated hot air continually
distributes heat more evenly than the natural movement of air in a
standard thermal oven. This movement of hot air helps maintain a
consistent temperature throughout the oven, cooking foods more
evenly, crisping surfaces while sealing in moisture and yielding
crustier breads.
Most foods can be cooked by lowering cooking temperatures
25°F to 50°F (14°C to 28°C), and cooking time can be shortened
by as much as 30 percent, especially for large turkeys and roasts.
■ It is important not to cover foods with lids or aluminum foil so
that surface areas remain exposed to the circulating air,
allowing browning and crisping.
■ Keep heat loss to a minimum by opening the oven door only
when necessary.
■ Choose cookie sheets without sides and roasting pans with
lower sides to allow air to move freely around the food.
15
■ Test baked goods for doneness a few minutes before the
minimum cooking time with a method such as using a
toothpick.
Convect Roast (on some models)
WARNING
Burn Hazard
Use an oven mitt to remove temperature probe.
Do not touch broil element.
Failure to follow these instructions can result in burns.
■ Use a meat thermometer or the temperature probe (on some
models) to determine the doneness of meats and poultry.
Convect Bake (on some models)
Convect Bake can be used to bake and cook foods on single or
multiple racks. It is helpful to stagger items on the racks to allow
a more even flow of heat. If the oven is full, extra cooking time
may be needed.
When cooking an oven meal with several different types of foods,
be sure to select recipes that require similar temperatures.
Cookware should sit in the oven with at least 1" (2.5 cm) of space
between the cookware and the sides of the oven.
Allow the range to preheat before placing food in the oven.
During convection baking preheat, the broil elements and the
bake element all heat the oven cavity. After preheat, the
convection element will cycle on and off in intervals to maintain
oven temperature, while the fan constantly circulates the hot air.
If the oven door is opened during convection baking or
preheating, the convection element and fan will turn off
immediately. They will come back on once the door is closed.
■ If Auto Convect is off, reduce recipe temperature 25°F (14°C).
The cook time may need to be reduced also.
To Convect Bake:
Before convection baking, position racks according to the
“Positioning Racks and Bakeware” section.
1. Press CONVECT.
2. Select CNVT BAKE using the left Quickset pad.
3. Select the oven temperature using the Quickset pads.
OR
Press the number pads to enter a temperature. The
temperature can be set between 195°F and 550°F (91°C and
288°C) in 5° increments when Auto Convect is on. If Auto
Convect is off, temperature can be set from 170°F (77°C).
4. Press ENTER.
After 3 seconds, the oven will begin to preheat. “CNVT
BAKE” and “PREHEAT” will appear in the display along with
100° or the actual oven temperature, whichever is higher.
The temperature in the display will increase in 1° increments
until the oven reaches the preset temperature. Allow about
15 minutes for the oven to preheat.
When the oven is preheated, the oven will beep, “PREHEAT”
will turn off and “CNVT BAKE” will be displayed. “AUTO” will
be displayed if Auto Convect conversion feature is turned on.
5. Place food in the oven.
6. Press CANCEL when finished cooking.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
Convection Roast can be used to roast meat and poultry, and
vegetables.
To Convect Roast:
Before convection roasting, position racks according to the
“Positioning Racks and Bakeware” section. It is not necessary to
wait for the oven to preheat before putting food in, unless
recommended in the recipe. If a recipe suggest preheating the
oven, add 15 minutes to the cook time.
1. Place food in the oven.
2. Press CONVECT.
3. Use the right Quickset pad to scroll to CNVT ROAST.
4. Select CNVT ROAST using the left Quickset pad.
5. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
The temperature can be set between 170°F and 550°F
(77°C and 288°C) in 5° increments.
6. Press ENTER pad to set.
7. Select the cook time using the Quickset pads.
OR
Enter the desired cook time using the number pads.
NOTE: If Auto Convect is off, a roast time will not be required.
8. Press ENTER pad to set.
After 3 seconds, the oven will begin to heat. “CNVT ROAST”
will appear in the display along with “100°” or the actual oven
temperature, whichever is higher.
The temperature in the display will increase in 1° increments
until the oven reaches the preset temperature.
Cook time will begin to count down.
9. At 75% of the cooking time the oven will beep to let you know
to check food. Check food using a meat thermometer.
If food is done, take food out of oven and press CANCEL pad
to turn oven off.
If food is not done, continue roasting.
Once the set time has elapsed the oven will automatically go
into Keep Warm
taken from the oven before the hour has elapsed, press the
CANCEL pad.
TM
mode for 1 hour and then shut off. If food is
16
Convect Pastry
(on some models)
Convect Pastry is designed to bake pastry items such as frozen
pies, turnovers, cream puffs and puff pastry. Use 1, 2 or 3 racks
while using this feature.
1. Press CONVECT.
2. Use the right Quickset pad to scroll to CNVT PASTRY.
3. Select CNVT PASTRY using the left Quickset pad.
4. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
The temperature can be set between 195°F and 550°F
(91°C and 288°C) in 5° increments.
5. Press ENTER pad to set.
After 3 seconds, the oven will begin to preheat. “CNVT
PASTRY” and “PREHEAT” will appear in the display along
with “100°” or the actual oven temperature, whichever is
higher. AUTO will display if the Auto Convect conversion
feature is turned on.
The temperature in the display will increase in 1° increments
until the oven reaches the preset temperature. Allow about
15 minutes for the oven to preheat.
When the oven is preheated, the oven will beep, “PREHEAT”
will turn off and “CNVT PASTRY” will be displayed.
6. Press CANCEL when finished cooking.
Rapid Preheat
(on some models)
Use Rapid Preheat to decrease preheating time when using Bake
or Convect Bake. Use for all foods when baking on 1 rack.
For best results, use rack position 2 or 3 when using the Rapid
Preheat option.
For optimum baking and browning results, Rapid Preheat is not
recommended when baking on multiple racks.
To A ct ivate :
After Bake or Convect Bake has been programmed and
activated, press RAPID PREHEAT.
“1 RACK ONLY” will display, after 10 seconds the display will
show “RAPID” and “PREHEAT.”
Preheat time is 5 minutes.
To Return to Standard Preheat:
Press RAPID PREHEAT. This will provide standard preheat.
“PREHEAT” and the selected function will be displayed.
More Options
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
Cook & Hold
1. Press MORE OPTIONS.
2. Select COOK/HOLD using the left Quickset pad.
3. Select the cook time using the Quickset pads.
OR
Enter the desired cook time using the number pads.
4. Press ENTER pad to set.
5. Select BAKE or CONVECT using the Quickset pads.
When CONVECT is pressed, scroll to CNVT BAKE, CNVT
ROAST or CNVT PASTRY then select the desired function
using the left Quickset pad.
6. Select the temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
IMPORTANT: If the recipe recommends preheating the oven, add
15 minutes to the cook time.
Delay
To Set Delay Bake:
1. Press MORE OPTIONS.
2. Use the right Quickset pad to scroll to DELAY.
3. Select DELAY using the left Quickset pad.
4. Select Delay time using Quickset pads or the number pads.
5. Select BAKE.
6. Select from the displayed temperatures or use the number
pads to enter the temperature.
7. Select the time to cook from the displayed times or use the
number pads to enter the cooking time.
8. The display will show “DELAY TIME,” the selected function,
the preset temperature and the delay time countdown.
When the delay time has expired, the cook time will be displayed
and the oven will begin to preheat.
17
To Set Delay Convect (on some models):
1. Press MORE OPTIONS.
2. Use the right Quickset pad to scroll to DELAY.
3. Select DELAY using the left Quickset pad.
4. Select Delay time using Quickset pads or the number pads.
5. Use the right Quickset pad to scroll to CONVECT.
6. Select CONVECT using the left Quickset pad.
7. Use the right Quickset pad to scroll to CNVT BAKE, CNVT
ROAST or CNVT PASTRY.
8. Select the desired function using the left Quickset pad.
9. Select from the displayed temperatures or use the number
pads to enter the temperature.
10. Select the time to cook from the displayed times or use the
number pads to enter the cooking time.
The display will show “DELAY TIME,” the selected function,
the preset temperature and the delay time countdown.
When the delay time has expired, the cook time will be displayed
and the oven will begin to preheat.
Proofing (on some models)
The Proofing feature can be used to raise yeast-based bread
products prior to baking. There are two proofing methods
available – Rapid and Standard.
Standard proofing in the oven avoids damage to dough from
room temperature changes or drafts that commonly affect
proofing done on the countertop.
Rapid proofing provides faster proofing results than countertop
or Standard proofing, without harming the yeast.
To Proof:
1. Press MORE OPTIONS.
2. Use the right Quickset pad to scroll to PROOFING.
3. Select PROOFING using the left Quickset pad.
4. Select RAPID or STANDARD using the Quickset pads.
5. Press CANCEL when finished proofing.
NOTES:
■ For any dough that requires one rise, either Standard or
Rapid Proofing can be used.
■ When using frozen bread dough, choose Rapid Proofing.
There is no need to thaw dough before proofing.
■ For dough requiring 2 rises, Standard Proofing must be used
for the first rising period. Either Standard or Rapid Proofing
can be used for the second rise.
■ If oven temperature is too high for proofing, “OVEN
COOLING” will appear in the display.
To U se :
1. Press MORE OPTIONS.
2. Use the right Quickset pad to scroll to KEEP WARM.
3. Select KEEP WARM using the left Quickset pad.
4. Select one of the displayed temperatures or enter desired
temperature using the number pads. Temperatures can be
selected between 145°F and 190°F (63°C and 88°C).
“KEEP WARM” and the temperature will be displayed.
“PREHEAT” will be displayed until the programmed
temperature is reached.
When oven has preheated, a beep sounds and “KEEP
WARM” and the temperature will be displayed.
5. Press CANCEL when finished.
To Warm Dinner Rolls:
1. Cover rolls loosely with foil and place in oven.
2. Press MORE OPTIONS.
3. Use the right Quickset pad to scroll to KEEP WARM.
4. Select KEEP WARM using the left Quickset pad.
5. Select 170° (77° in Celsius) temperature. Warm for 12 to
15 minutes.
To Warm Plates:
NOTES:
Use only oven-safe plates. Check with the manufacturer.
To avoid crazing or breakage, do not set warm dishes on a cold
surface.
1. Place 2 stacks of up to 4 plates each in the oven.
2. Press MORE OPTIONS.
3. Use the right Quickset pad to scroll to KEEP WARM.
4. Select KEEP WARM using the left Quickset pad.
5. Select 170° (77° in Celsius) temperature. Warm for 5 minutes.
Press CANCEL to turn off the oven and leave plates in the
oven for 15 minutes more.
Warming Drawer
(on some models)
WARNING
Food Poisoning Hazard
Do not let food sit for more than one hour before or
after cooking.
Doing so can result in food poisoning or sickness.
Keep Warm
IMPORTANT: Food must be at serving temperature before
placing it in the warmed oven. Food may be held up to 1 hour;
however, breads and casseroles may become too dry if left in the
oven during Keep Warm
The Keep Warm
serving temperature. It can also be used at the end of a timed
cook.
Follow manufacturer’s recommendations when warming empty
serving bowls and plates.
TM
Feature
TM
TM
feature allows hot cooked foods to stay at
.
18
The Warming Drawer is ideal for keeping hot cooked foods at
serving temperature. It may also be used for warming breads and
pastries.
Different types of food may be placed in the warming drawer at
the same time. For best results, do not hold foods longer than
1 hour. For smaller quantities or heat-sensitive foods, such as
eggs, do not hold longer than 30 minutes.
Food must be at serving temperature before being placed in the
warming drawer. Breads, pastries, and fruit pies may be heated
from room temperature.
Remove food from plastic bags and place in oven-safe container.
Cover foods with a lid or aluminum foil.
Do not cover with plastic wrap.
A
Empty serving dishes and ovenproof dishes can be heated while
the warming drawer is preheating.
Before using the warming drawer, wash the tray that lines the
bottom of the drawer with soap and water. See “General
Cleaning” section.
To U se :
1. Press WARM DRAWER.
2. Press the Quickset pad for HIGH or LOW. Use the following
chart as a guide.
3. Allow the drawer to preheat for 10 minutes.
4. Place cooked food(s) in warming drawer.
5. Press WARM DRAWER when finished.
6. Remove food from the drawer.
SETTING TYPE OF FOOD
High
Low
■ Bacon
■ Beef - rare
■ Casseroles
■ Cooked cereals
■ Dinner plate
■ Enchiladas
■ Eggs
■ Fish/seafood
■ Gravy, cream
sauces
■ Ham
■ Biscuits
■ Coffee Cake
■ Hamburger patties
■ Hors d’oeuvres
■ Lamb
■ Pancakes
■ Pizza
■ Pork
■ Potatoes - baked
■ Potatoes - mashed
■ Poultry
■ Vegetables
■ Waffles
■ Pies
■ Warming - plates
Meat Probe
(on convection models)
WARNING
Burn Hazard
Use an oven mitt to remove temperature probe.
Do not touch broil element.
Failure to follow these instructions can result in burns.
The meat probe accurately measures the internal temperature of
meat, poultry and casseroles with liquid and should be used in
determining the doneness of meat and poultry. It should not be
used during full and center broiling, convection broiling,
dehydrating or proofing bread.
Always unplug and remove the meat probe from the oven when
removing food.
To U se :
Before using, insert the probe into the center of the thickest
portion of meat or into the inner thigh or breast of poultry, away
from fat or bone at an angle as shown in following diagram. Place
food in oven. Using the handle of the probe, connect the meat
probe to the jack. Keep probe as far away from heat source as
possible. Close oven door.
B
A. Meat probe
B. Meat probe jack
1. Press MORE OPTIONS.
2. Use the right Quickset pad to scroll to MEAT PROBE.
3. Select MEAT PROBE using the left Quickset pad.
4. Set the desired internal food temperature by selecting one of
the displayed temperatures or use the number pads to enter
the temperature. The probe temperature can be set between
100°F and 185°F (38°C and 85°C).
If the meat probe is not inserted, “INSERT PROBE” will be
displayed.
5. Select BAKE or CONVECT.
6. If CONVECT was selected, select CNVT BAKE, CNVT ROAST
or CNVT PASTRY.
7. Set the oven temperature by selecting one of the displayed
temperatures or use the number pads to enter the
temperature.
The display will briefly show the selected temperatures for the
oven and probe.
After 10 seconds, the display will show the actual oven
temperature and actual probe temperature.
IMPORTANT: If the probe is removed from the oven
receptacle at any time during the cooking process, the
control will prompt “INSERT PROBE.” If the probe is not
reinserted within 30 seconds, the program will be canceled
and the oven will turn off.
8. When the selected internal temperature of the food has been
reached, the oven will shut off and “PROBE END” appears on
the display.
NOTE: To avoid overcooking the food, remove it from the
oven as soon as the oven shuts off.
9. Using the handle of the probe, remove the probe from the
jack. The probe will be hot. Hold probe with an oven mitt or
pot holder when removing from the oven.
To Change Probe Temperature, Oven Setting:
Press CANCEL, then repeat previous steps.
After cooking, unplug the probe and remove food from oven.
See “General Cleaning” section to clean probe.
19
Drying (on some models)
For best results, use a drying rack. A drying rack allows air to
circulate evenly around the food.
The convection fan will operate during the drying procedure.
To S et Drying:
1. Open the oven door slightly. The oven door needs to be
opened slightly to allow moisture to escape from the oven
during the drying process.
2. Place the magnetic door spacer Part Number 8010P146-60
over the plunger switch. The spacer provides a gap between
the oven frame and the oven door to allow moisture to
escape.
A
A. Magnetic door spacer
DRYING GUIDE CHART
■ The length of drying times vary due to water and sugar
content of food, size of food pieces, amount of food being
dried, humidity in the air.
■ Check foods at the minimum drying time. Dry longer if
necessary.
■ Fruits that turn brown when exposed to air should be
treated with an antioxidant. Try one of the following
methods:
1. Dip fruit in a mixture of 3 tbs (44.4 mL) lemon juice to
1 qt (0.95 L) of cool water.
2. Soak fruit in a solution of 1 tsp (4.9 mL) ascorbic acid
or commercial antioxidant to 1 qt (0.95 L) of cold
water.
3. Gently close the door until the spacer magnet makes contact
with the oven door. The magnet will hold the spacer in the
proper position during the drying process and allows the door
to be opened at any time during drying without losing proper
positioning.
IMPORTANT: If the spacer is not placed correctly, the
convection fan will not operate.
4. Press CONVECT.
5. Use the right Quickset pad to scroll to DRYING.
6. Select DRYING using the left Quickset pad.
7. Use the Quickset pads to select a displayed temperature or
enter a temperature with the number pads. Temperatures can
be set between 100°F and 200°F (38°C and 93°C).
8. “DRYING” and the temperature will be displayed. “PREHEAT”
will be displayed until the programmed temperature is
reached.
9. Press CANCEL when finished drying.
Follow the Drying Guide chart for drying times.
Check foods at minimum times given. Cool foods to room
temperature before testing for doneness.
■ Most fruits and vegetables dry well and retain their color when
dried at 140°F (60°C). Meat and jerky should be dried between
145°F and 150°F (63°C and 65°C). For optimal flavor, dry herbs
at 100°F (38°C), however, at this lower temperature expect
extended drying times of up to 8 hours.
■ Foods may drip during the drying process. After drying high
acid or sugary foods, clean the oven bottom with soap and
water. The porcelain oven finish may discolor if acidic or sugary
food soils are not wiped up prior to high heat or a self-cleaning
cycle.
■ More than one rack of food may be dried at the same time.
However, additional drying time is needed.
■ Refer to other resources at your local library or call your local
agricultural department service for additional information.
FOOD VARIETIES BEST FOR
DRYING
PREPARATION APPROX. DRY
TIME AT 140°F
TEST FOR DONENESS
AT MINIMUM DRY TIME
(60°C) [HOURS]**
FRUIT
Apples* Firm varieties: Graven
Stein, Granny Smith,
Jonathan, Winesap, Rome
Wash, peel if desired, core and
slice into ¹⁄₈" (3.0 mm) slices.
4 to 8 Pliable to crisp. Dried
apples store best when
slightly crisp.
Beauty, Newton
Apricots* Blenheim/Royal most
Wash, halve, and remove pits. 18 to 24 Soft and pliable
common. Tilton also good.
Bananas* Firm varieties Peel and cut into ¼" (6.0 mm)
17 to 24 Pliable to crisp
slices.
Cherries Lambert, Royal Ann,
Napoleon, Van or Bing
Nectarines and
Freestone varieties Halve and remove pits. Peeling is
Peaches*
Wash and remove stems. Halve
and remove pits.
optional but results in better-
18 to 24 Pliable and leathery
24 to 36 Pliable and leathery
looking dried fruit.
Pears* Bartlett Peel, halve and core. 24 to 36 Soft and pliable
20
Loading...