Dispose of the unit and used batteries in an environment friendly manner
according to your country regulations.
FR - DÉCLASSER L’APPAREIL
Débarrassez-vous de l’appareil et des piles usagées de manière écologique
Conformément aux dispositions légales de votre pays.
NL - VERWIJDEREN VAN HET APPARAAT
Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke
manier conform de in uw land geldende voorschriften.
DU - ENTSORGUNG DES GERÄTS
Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und
Weise gemäß den Vorschriften Ihres Landes.
ES - DESHACERSE DEL APARATO
Reciclar el aparato y pilas usadas de forma ecologica conforme a las
disposiciones legales de su pais.
PT - COMO DESFAZER-SE DA UNIDADE
Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em
conformidade com as normas vigentes no seu país.
ENGLISH OPERATION MANUAL
ENGLISH OPERATION MANUAL
SAFETY INSTRUCTIONS:
Thank you for buying this JB Systems product. To take full advantage of all possibilities, please read these
operating instructions very carefully.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
• Extremely versatile power supply for all kinds of passive RGB LED-projectors.
• Different standalone working modes:
• Fixed color mode: Instant access to 9 pre-programmed colors
• Static chase mode: 12 different color chases with manual speed control
• Sound chase mode: 12 different color chases with audio triggering
• Spectrum mix: 32 different spectrum mix colors, including nice color fades
• Adjustable speed and dimming with faders
• Slow color fades with adjustable fade time
• Blackout and “Full on” function
• All functions can be controlled directly on the on the LED-Manager or by the optional LEDCON-01 remote.
• Several LED-Managers can be used in Master/slave mode to create high power, fully synchronized setups.
• Enclosure prepared for easy installing against the wall.
• Fan cooling for extra reliability.
BEFORE USE
Check the contents:
Check that the carton contains the following items:
• LED-Manager
• Mains cable
• User manual
Some important instructions:
• Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
•Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
• Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
• To protect the environment, please try to recycle the packing material as much as possible.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use
or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instructions in the literature accompanying this
appliance.
This symbol means: indoor use only.
• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
• To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
• This unit is for indoor use only.
• Don’t place metal objects or spill liquid inside the unit. No objects filled with liquids, such as vases, shall be
placed on this appliance. Electric shock or malfunction may result. If a foreign object enters the unit,
immediately disconnect the mains power.
• No naked flame sources, such as lighted candles, should be placed on the appliance.
• Don’t cover any ventilation openings as this may result in overheating.
• Prevent use in dusty environments and clean the unit regularly.
• Keep the unit away from children.
• Inexperienced persons should not operate this device.
• Maximum save ambient temperature is 45°C. Don’t use this unit at higher ambient temperatures.
• Always unplug the unit when it is not used for a longer time or before you start servicing.
• The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
• Check that the available voltage is not higher than the one stated on the rear panel of the unit.
• The socket inlet shall remain operable for disconnection from the mains.
• The power cord should always be in perfect condition: switch the unit immediately off when the power cord
is squashed or damaged.
• Never let the power-cord come into contact with other cables!
• In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no user
serviceable parts inside.
•Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
• In the event of serious operating problems, stop using the appliance and contact your dealer immediately.
• Please use the original packing when the device is to be transported.
• Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
MAINTENANCE
• Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside the unit. Do not
use volatile liquids such as benzene or thinner which will damage the unit.
• Since this unit uses a cooling fan, the interior of the device should be cleaned annually using a vacuum
cleaner or air-jet.
Attention:
CAUTION
We strongly recommend internal cleaning to be carried out by qualified personnel!
CAUTION: To reduce the risk of electric shock, do not remove the top cover.
No user-serviceable parts inside. Refer servicing to qualified service
personnel only.
JB SYSTEMS® 1/46 LED MANAGER
JB SYSTEMS® 2/46 LED MANAGER
ENGLISH OPERATION MANUAL
FUNCTIONS (FRONT)
ENGLISH OPERATION MANUAL
FUNCTIONS (REAR)
1. MENU BUTTON: used to enter/leave the main menu. To return from the main menu to clock display just
press the menu button for 1second.
2. ENTER BUTTON: used to confirm your choice in the menu.
3. UP/DOWN BUTTONS: used to browse through the main menu and adapt the values of a function.
4. STATUS MONITOR: indicates some important working conditions:
• DMX-LED: indicates that the unit is working in DMX mode. (a DMX-signal is detected)
• MASTER LED: indicates that the unit is working in master mode.
• SLAVE LED: indicates that the unit is working in slave mode.
• SOUND LED: indicates that a music signal is picked up by the internal microphone.
5. DISPLAY: 4digit LED display shows different menu options and real-time clock.
6. FIXED COLOR BUTTONS: 9 buttons each with a preset color.
7. MODE SELECT BUTTONS: 3 buttons used to set the controller in different working modes:
• FIXED COLORS: select this mode if you want to use the “fixed color” buttons (6).
• CHASE MODE: select this mode if you want to select one of the 12 color chases using the
“chase/color” fader (8).
• SPECTRUM MIX: select this mode if you want to select one of the 32 different colors using the
8. CHASE/COLOR FADER: used to select one of the available color chases:
9. SPEED/FADE FADER: used to select the chase speed or color fade time:
10. MASTER FADER: used to control the overall dimming of the LEDs and overall strobe speed.
11. SOUND BUTTON: used to toggle the chase mode between sound and static mode.
12. FULL ON BUTTON: used to set the 3 colors (R+G+B) at maximum level.
13. BLACKOUT BUTTON: used to set the 3 colors (R+G+B) at zero level.
14. OUTPUT MONITOR: indicates the output levels for the 3 colors (R+G+B)
“chase/color” fader (8).
• Left side of the fader indicates the different chases.
• Right side of the fader indicates the different colors.
Important remark:
lighting” applications. Select this function to fade gently from one color to another. You can adjust
the fade-over time with the speed/fade fader(9).
• Left side of the fader indicates the chase speed, ranging from 2,5s to 0,1s.
• Right side of the fader indicates the color fade time, ranging from 12s to 2,5s.
There’s also a function called “color fade” which is very nice for “background
JB SYSTEMS® 3/46 LED MANAGER
15. FIXING HOLES: used to fix the unit on a wall or other flat surface.
16. OUTPUT CABLES: used to connect different 24Vdc common anode LED projectors. (max. load: 300W)
Each cable uses a special 4pin female connector.
17. OUTPUT FUSES: 6,3A fuses on each of the 3 color outputs.
18. DMX INPUT: 3pin male XLR-connector used to connect universal DMX-cables. This input receives
instructions from a DMX-controller or from another LED-Manager when used in master/slave mode.
19. DMX OUTPUT: 3pin female XLR-connector used to connect the LED-Manager with the next DMX
appliance in the chain or with another LED-Manager when used in master/slave mode.
20. INTERNAL MICRO: used for sound activated chases.
21. MAINS INPUT: with IEC socket and integrated fuse holder, connect the supplied mains cable here.
22. ON/OFF SWITCH: used to switch the unit on/off.
ELECTRICAL INSTALLATION
The electrical installation should be carried out by qualified personal only, according to the
regulations for electrical and mechanical safety in your country.
How to connect the LED-projectors to the outputs of the unit:
Important:
load of the LED Manager is 300W, spread over 3 colors: each of the 3 colors has a max. load of
100W! The total load is distributed over the 2 output cables. This means that each output cable
supports 150W (max. 50W for each color!) to have a total maximum load of 300Watt. Make sure not
to overload one of the output cables!
The 2 output cables (16) use a special 4pin connector. Two different types of passive LED projectors can
be connected:
Switch the LED-manager OFF before you install the LED-projectors! The maximum total
A. LED Projectors with a special 4pin connector (ex. LED STRIP):
This is the easiest way to
make the connections. Fix
all projectors properly and
daisy chain their in/output
cables until you reach the
maximum allowed load. Make sure to fasten the plastic ring of the connector.
Example: you can connect up to fifteen “1m LED STRIP” on each output cable (total = 30m!)
B. LED Projectors with open wires (ex. LED GROUND LIGHT):
In this case we suggest to take a 1m extension cable (with
special male/female 4pin connectors) and to cut the female
connector. Now you can easily strip the cable. You will find 4
colored wires inside:
• White wire: This is the common wire (anode)
• Red wire: This the power for the red LEDs (max. 50W)
• Green wire: This the power for the green LEDs (max. 50W)
JB SYSTEMS® 4/46 LED MANAGER
ENGLISH OPERATION MANUAL
•Blue wire: This the power for the blue LEDs (max. 50W)
Just connect these 4 wires to the corresponding 4 wires of the projector. (in most cases the colors of
the wires match with the LED colors) Make sure not to exceed the maximum allowed load!
Example: you can connect up to 50 “GROUND LIGHT” on each output cable (total = 100pcs!)
Electrical installation in Master/slave-mode:
• You need to “daisy chain” the DMX in/outputs of 2 or more units with a good quality balanced cable (ex.
JB Systems ref. 7-0063).
• The unit with a free DMX-input connector automatically becomes the master (master LED is lit), the other
units are automatically switched as slaves (slave LED is lit). The controls on the slave units are disabled.
Electrical installation in Master/slave-mode with the LEDCON-01 remote:
• You need to “daisy chain” the DMX in/outputs of 1 or more units with the output of the LEDCON-01
remote using a good quality balanced cable (ex. JB Systems ref. 7-0063).
• The LEDCON-01 remote will be used to control all connected slaves. The LED Managers are
automatically switched as slaves (slave LED is lit). The controls on the slave units are disabled.
Electrical installation in DMX-mode:
• The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
“daisy chain” your DMX controller and all the connected units with a good quality balanced cable (ex. JB
Systems ref. 7-0063).
• To prevent strange behavior of the light effects, due to interferences, you must use
a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this
simply won’t work!
• Each unit in the chain needs its proper start address so it knows which commands
from the DMX-controller it has to decode. When you need a lot of power you can
use several LED managers and give them the same start address. In the next chapter you will learn how
to set the DMX addresses.
JB SYSTEMS® 5/46 LED MANAGER
ENGLISH OPERATION MANUAL
Changing the internal batteries:
VERY IMPORTANT: ONLY rechargeable batteries are allowed, do NOT use normal batteries!!!
The LED Manager has an internal real-time 24H clock with 3 individual timers and battery backup. To use
the battery backup feature you must install 3 optional AA-type NiMH rechargeable batteries. Once these
batteries are installed they will be recharged automatically, no need to replace them anymore!
• Switch the unit off and disconnect the mains cable.
• Use an appropriate screwdriver to unscrew the 10
screws of the enclosure.
• Gently remove the top cover (careful for the cables
inside!)
• On the inside you will find a battery compartment,
next to the fan. Open it gently and install the 3 AAtype NiMH rechargeable batteries as indicated.
• Close the battery compartment
• Put the top cover back in place and fasten the 10
screws.
• Connect the unit to the mains: the batteries will
charge automatically.
• Done!
SETUP MENUS + DMX ADDRESSING
During normal operation the display shows the current
time of the internal 24H clock.
• Press the MENU button to enter menu mode:
• With the UP and DOWN buttons you can browse
through the different options of the main menu.
• Press the ENTER button to select and edit a menu
option.
• Adapt the values with the UP & DOWN buttons and
confirm with the ENTER button or press the MENU
button again if you want to return to the main menu
without saving the changes you just made.
• After some time the display will automatically show
the internal clock. You can also switch to the clock
display by pressing the MENU button for about 1
second.
DMX start address setting
Used to set the start address of the LED Manager.
• Press the MENU button and UP/DOWN buttons until
the display shows “Addr”
• Press the ENTER button: the display starts blinking.
• Use the DOWN and UP buttons to change the DMX
address.
• Once the correct address is shown on the display, press the ENTER button to save it.
Remarks: You can abort the setting procedure and go back without saving the changes by shortly pressing
the MENU button. When the setup is done and changes are saved, you can return to the clock display by
pressing the MENU button for more than 1second.
Internal 24H clock setting
Used to set the time of the internal 24H clock.
• Press the MENU button and UP/DOWN buttons until the display shows “time”
• Press the ENTER button, the HOUR-display starts blinking.
• Use the DOWN and UP buttons to set the correct hours (00 to 23).
• Press the ENTER button, the MINUTE-display starts blinking.
• Use the DOWN and UP buttons to set the correct minutes (00 to 59).
JB SYSTEMS® 6/46 LED MANAGER
ENGLISH OPERATION MANUAL
• Once the correct time is shown, press the ENTER button. The new clock settings are saved while the
display shows “time”
Remarks: You can abort the setting procedure and go back without saving the changes by shortly pressing
the MENU button. When the setup is done and changes are saved, you can return to the clock display by
pressing the MENU button for more than 1second.
ON/OFF Timers “START-time” setting
The LED Manager has 3 individual ON/OFF timers. So you are able to switch the output on/off at 3 different
parts of the day, each time with a different color or color chase. Below we explain how to set the start-time
for “ON/OFF timer1”. The settings for the other 2 timers are identical.
• Press the MENU button and UP/DOWN buttons until the display shows “t1on”
• Press the ENTER button, the HOUR-display starts blinking.
• Use the DOWN and UP buttons to set the correct hours (00 to 23).
• Press the ENTER button, the MINUTE-display starts blinking.
• Use the DOWN and UP buttons to set the correct minutes (00 to 59).
• Once the correct start time is shown, press the ENTER button. The new start time is saved while the
display shows “t1on”
Remarks: You can abort the setting procedure and go back without saving the changes by shortly pressing
the MENU button. When the setup is done and changes are saved, you can return to the clock display by
pressing the MENU button for more than 1second.
ON/OFF Timer “STOP-time” setting
Below we explain how to set the stop-time for “ON/OFF timer1”. The settings for the other 2 timers are
identical.
• Press the MENU button and UP/DOWN buttons until the display shows “t1oF”
• Press the ENTER button, the HOUR-display starts blinking.
• Use the DOWN and UP buttons to set the correct hours (00 to 23).
• Press the ENTER button, the MINUTE-display starts blinking.
• Use the DOWN and UP buttons to set the correct minutes (00 to 59).
• Once the correct stop time is shown, press the ENTER button. The new stop time is saved while the
display shows “t1oF”
Remarks: You can abort the setting procedure and go back without saving the changes by shortly pressing
the MENU button. When the setup is done and changes are saved, you can return to the clock display by
pressing the MENU button for more than 1second.
ENGLISH OPERATION MANUAL
B. Two or more units in master/slave setup:
• Connect the LED projectors to the LED Managers as indicated in the previous chapters.
• Connect the units with each other as explained in the chapter about electrical installations. (no need to
set a DMX address!
• Switch the LED Managers on. You can only use the controls on the master unit, the controls on the
slaves are disabled. Refer to the chapter “Functions” to make yourself familiar with the various
functions of the faders and buttons on the master unit.
In this mode you can also set the clock and use the 3 on/off timers on the master as described in the
previous chapter.
Remark: When a timer is active, you can deactivate it by pressing the blackout button.
C. Connect the optional LEDCON-01 controller for remote control:
In most cases the LED MANAGER will be installed on a wall, close to the LED-projectors. If you want to
have easy access to its functions, you can connect the LEDCON-01 remote controller to the (first) LED
Manager. The other connections are identical to those of the standalone or master/slave setups.
Except for the display, internal 24H clock and the 3 on/off timers, the controls on the remote are identical
to that of the LED Manager. So please refer to the chapter “Functions” to make yourself familiar with the
various functions of the faders and buttons.
D. Controlled by universal DMX-controller:
• Connect the LED projectors to the LED Manager(s) as indicated in the previous chapters.
• Connect the LED Manager(s) with all other DMX-appliances in the DMX-chain.
• Switch all units on and set the proper DMX-addresses. (DMX-LED on the LED Manager is lit)
• Switch your universal DMX-controller on and refer to the DMX chart below to control the connected
LED managers:
ON/OFF Timer “SCENE” setting
Below we explain how to select the scene (color or color chase) for “ON/OFF timer1”. The settings for the
other 2 timers are identical.
• Press the MENU button and UP/DOWN buttons until the display shows “t1rE”
• Press the ENTER button, the display starts blinking.
• Now you have the time to set the scene that you would like to reproduce when the timer is activated.
• When the scene is OK (don’t forget to switch the blackout function off!) just press the ENTER button again.
The display stops blinking and the scene is saved.
Remarks: You can abort the setting procedure and go back without saving the changes by shortly pressing
the MENU button. When the setup is done and changes are saved, you can return to the clock display by
pressing the MENU button for more than 1second.
OPERATING INSTRUCTIONS
A. Standalone 1unit:
• Connect the LED projectors to the LED Manager as indicated in the previous chapters. (no need to set
a DMX address!)
• Switch the unit on and refer to the chapter “Functions” to make yourself familiar with the various
functions of the faders and buttons.
In this mode you can also set the clock and use the 3 on/off timers as described in the previous chapter.
Remark: When a timer is active, you can deactivate it by pressing the blackout button.
JB SYSTEMS® 7/46 LED MANAGER
All controls (buttons and faders) on the LED Manager(s) are disabled, except the buttons needed to set
the DMX-address.
JB SYSTEMS® 8/46 LED MANAGER
ENGLISH OPERATION MANUAL
SPECIFICATIONS
Power Input: AC 230V~ 50Hz
Fuse: 6,3A slow blow (20mm glass)
Backup batteries: 3x 1,2V AA-type NiMH rechargeable batteries (optional)
Output voltage to LEDs: DC 24V common anode
Output power to LEDs: 2x 150W max. (Total = 300W max.)
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
o Red: 2x 50W max. (Total = 100W max.)
o Green: 2x 50W max. (Total = 100W max.)
o Blue: 2x 50W max. (Total = 100W max.)
FRANCAIS MODE D’EMPLOI
Nous vous remercions d’avoir acheté ce produit JB Systems. Veuillez lire ce mode d’emploi très
attentivement afin de pouvoir exploiter toutes les possibilités de cet appareil.
CARACTERISTIQUES
Cet appareil ne produit pas d’interférences radio. Il répond aux exigences nationales et européennes. La
conformité a été établie et les déclarations et documents correspondants ont été déposés par le fabricant.
• Alimentation polyvalente pour toutes sortes de projecteurs RVB LED passifs
• Différents modes de fonctionnement isolées:
• Fixed colors mode: accès immédiat aux 9 couleurs préprogrammées
• Static chase mode : 12 différents défilements de couleurs avec contrôle manuel de vitesse
• Sound chase mode : 12 différents défilements de couleurs avec déclenchement de signal audio
• Le boîtier est préparé pour une l'installation facile contre le mur
• Ventilateur pour une fiabilité supplémentaire
AVANT L’UTILISATION
Vérifiez le contenu:
Vérifiez si la boite contient les articles suivants :
• LED MANAGER
• Câble d’alimentation
• Mode d’emploi
Quelques instructions importantes:
• Avant d’utiliser cet appareil, assurez-vous de l’absence de dommage lié au transport. En cas
d’endommagement, n’utilisez pas l’appareil et contactez le vendeur.
•Important: Cet appareil a quitté notre usine en parfaite condition et bien emballé. Il est primordial que
l’utilisateur suive les instructions de sécurité et avertissements inclus dans ce manuel. La garantie ne
s’applique pas en cas de dommage lié à une utilisation incorrecte. Le vendeur ne prend pas la
responsabilité des défauts ou de tout problème résultant du fait de n’avoir pas tenu compte des mises en
garde de ce manuel.
• Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez l’appareil,
assurez-vous d’y joindre ce manuel également.
• Afin de protéger l’environnement, merci de recycler les emballages autant que possible.
JB SYSTEMS® 9/46 LED MANAGER
JB SYSTEMS® 10/46 LED MANAGER
FRANCAIS MODE D’EMPLOI
INSTRUCTIONS DE SECURITE:
CAUTION
techniciens qualifiés.
La flèche dans un triangle met l'utilisateur en garde de la présence de haut voltage sans isolation
dans l'appareil qui peut causer un risque d'électrocution.
Un point d'exclamation dans un triangle prévient de la présence d'instructions de fonctionnement et
de maintenance se trouvant dans le manuel, fourni avec l'appareil.
Ce symbole signifie : uniquement pour usage à l'intérieur
• Afin d’éviter tout risque d’incendie ou de choc électrique, ne pas exposer cet appareil à la pluie ou
l’humidité.
• Pour éviter la formation de condensation à l’intérieur de l’appareil, patientez quelques minutes pour laisser
l’appareil s’adapter à la température ambiante lorsqu’il arrive dans une pièce chauffée après le transport.
La condensation empêche l’unité de fonctionner en performance optimale et peut même causer des
dommages.
• Cette unité est destinée à une utilisation à l’intérieur uniquement.
• Ne pas insérer d’objet métallique ou verser un liquide dans l’appareil. Aucun objet rempli de liquides, tels
que des vases, ne sera placé sur cet appareil. Risque de choc électrique ou de dysfonctionnement. Si un
corps étranger est introduit dans l’unité, déconnectez immédiatement de la source d’alimentation.
• Aucune source de flamme nue, telle que les bougies allumées, ne devrait être placée sur l'appareil.
• Ne pas couvrir les ouvertures de ventilation, un risque de surchauffe en résulterait.
• Ne pas utiliser dans un environnement poussiéreux et nettoyez l’unité régulièrement.
• Ne pas laisser l’unité à portée des enfants.
• Les personnes non expérimentées ne doivent pas utiliser cet appareil.
• La température ambiante maximum d’utilisation de l’appareil est de 45°C. Ne pas l’utiliser au-delà de cette
température.
• Débranchez toujours l’appareil si vous ne l’utilisez pas de manière prolongée ou avant d’entreprendre des
réparations.
• Les installations électriques ne peuvent être faites que par du personnel qualifié et conformément aux
régulations de sécurité électrique et mécanique en vigueur dans votre pays.
• Assurez-vous que le voltage de la source d’alimentation de la zone dans laquelle vous vous trouvez ne
dépasse pas celui indiqué à l’arrière de l’appareil.
• La prise sera toujours accessible pour que le cordon secteur puisse être enlevé à chaque moment.
• Le cordon d’alimentation doit toujours être en condition parfaite. Mettez immédiatement l’unité hors tension
si le cordon est écrasé ou endommagé.
• Ne laissez jamais le cordon d’alimentation entrer en contact avec d’autres câbles !
• Utilisez toujours les câbles appropriés et certifiés lorsque vous installez l’unité.
• Pour éviter tout choc électrique, ne pas ouvrir l’appareil. En dehors du fusible principal, il n’y a pas de
pièces pouvant être changées par l’utilisateur à l’intérieur.
•Ne jamais réparer ou court-circuiter un fusible. Remplacez systématiquement un fusible endommagé par
un fusible de même type et spécifications électriques !
• En cas de problèmes de fonctionnement sérieux, arrêtez toute utilisation de l’appareil et contactez votre
revendeur immédiatement.
• Utilisez l’emballage d’origine si l’appareil doit être transporté.
• Pour des raisons de sécurité, il est interdit d’apporter toute modification à l’unité non spécifiquement
autorisée par les parties responsables.
ATTENTION: afin de réduire le risque d’électrocution, n’enlevez jamais le
couvercle de l’appareil. Il n’y a aucune pièce à l’intérieur de l’appareil que
vous pouvez remplacer vous-même. Confiez l’entretien uniquement aux
ENTRETIEN
• Nettoyez l’appareil à l’aide d’un chiffon doux, légèrement humide. Evitez d’introduire de l’eau à l’intérieur
de l’appareil. N’utilisez pas de produits volatiles tels le benzène ou le thinner qui peuvent endommager
l’appareil.
• Étant donné que cet appareil utilise un ventilateur, l’intérieur de l'appareil doit être nettoyé annuellement à
l'aide d'un aspirateur ou d'air sous pression.
Attention:
Nous conseillons que le nettoyage interne se fasse par une personne qualifiée.
FRANCAIS MODE D’EMPLOI
FONCTIONS (FACE AVANT)
1. BOUTON MENU: Utilisé pour consulter ou quitter le menu principal. Pour retourner du menu principal à
l'affichage de l’horloge appuyez 1 seconde sur le bouton menu.
2. BOUTON ENTER: Pour confirmer la fonction sélectionnée.
3. BOUTON UP/DOWN: Pour feuilleter dans le menu principal et sélectionner les valeurs d'une fonction.
4. MONITEUR STATUS: Indique quelques fonctions importantes:
5. ÉCRAN: écran 4digit LED, affiche les différentes options menu.
6. BOUTONS FIXED COLOR: 9 boutons, chacun avec une couleur préprogrammé.
7. BOUTONS MODE SELECT: 3 boutons pour placer le contrôleur sur différentes méthodes de
fonctionnement:
8. CURSEUR CHASE/COLOR: Utilisé pour sélectionner un des défilement de couleur disponible:
9. CURSEUR SPEED/FADE: Utilisé pour sélectionné la vitesse de transition ou le temps color fade.
10. CURSEUR MASTER: Utilisé pour régler la puissance de sortie vers les projecteurs LED et pour contrôler la vitesse du stroboscope.
11. BOUTON SOUND: Pour inverser le mode chase entre sound et static mode.
12. BOUTON FULL ON: Pour placer les 3 couleurs (R+G+B) au niveau max.
13. BOUTON BLACKOUT: Pour placer les 3 couleurs (R+G+B) au niveau zéro.
14. SORTIE MONITEUR: Indique le niveau sortie des 3 couleurs (R+G+B).
• LED DMX: Indique que l'appareil fonctionne en mode DMX. (un signal DMX est détecté).
• LED MASTER: Indique que l'appareil fonctionne en mode maître.
• LED SLAVE: Indique que l'appareil fonctionne en mode esclave.
• LED SOUND: Clignote au rythme de la musique, détecté par le micro intégré.
• FIXED COLORS: Sélectionnez ce mode, si vous voulez utiliser les boutons ‘fixed color’.
• CHASE MODE: Sélectionnez ce mode, si vous voulez utiliser un des 12 défilement de couleur en
utilisant le curseur ‘chase/color’ (8).
•SPECTRUM MIX: Sélectionnez ce mode, si vous voulez utiliser une des 32 couleurs différentes
en utilisant le curseur ‘chase/color (8).
• Le côté gauche du curseur indique les différents défilements.
• Le côté droits du curseur indique les différentes couleurs.
Remarque importante:
plan. Sélectionnez cette fonction pour passer progressivement d’une couleur vers une autre. Vous
pouvez adapter la période de transition avec le curseur ‘speed’(9).
• Le côté gauche du curseur indique la vitesse de transition, de 2,5s à 0,1s.
• Le côté droits du curseur indique le temps color fade, de 12s à 2,5s.
Il y a une fonction ‘color fade’ qui est très joli pour un éclairage d’arrière
JB SYSTEMS® 11/46 LED MANAGER
JB SYSTEMS® 12/46 LED MANAGER
Loading...
+ 17 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.