JBSYSTEMS LIGHT LED GROUND LIGHT User Manual
LED GROUND LIGHTLED GROUND LIGHT
LED RGB-PASSIVE GROUND LIGHT
F
P6
I 7
W
ATE
RP
RO
O
WWW.BEGLEC.COM
Copyright © 2006 by BEGLEC cva.
Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.
Version: 1.1
Operation Manual
Mode d'emploi
Gebruiksaanwijzing
Bedienungsanleitung
Manual de instrucciones
EN
FR
NL
DU
ES
EN - DISPOSAL OF THE DEVICE
Dispose of the unit and used batteries in an environment friendly manner
according to your country regulations.
FR - DÉCLASSER L’APPAREIL
Débarrassez-vous de l’appareil et des piles usagées de manière écologique
Conformément aux dispositions légales de votre pays.
NL - VERWIJDEREN VAN HET APPARAAT
Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke
manier conform de in uw land geldende voorschriften.
DU - ENTSORGUNG DES GERÄTS
Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und
Weise gemäß den Vorschriften Ihres Landes.
ES - DESHACERSE DEL APARATO
Reciclar el aparato y pilas usadas de forma ecologica conforme a las
disposiciones legales de su pais.
PT - COMO DESFAZER-SE DA UNIDADE
Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em
conformidade com as normas vigentes no seu país.
ENGLISH OPERATION MANUAL
Thank you for buying this JB Systems product. To take full advantage of all possibilities and for your own
safety, please read these operating instructions very carefully before you start using this unit.
ENGLISH OPERATION MANUAL
• Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Don’t use the effect in the presence of persons suffering from epilepsy.
DESCRIPTION:
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
• This device has been designed to produce decorative effect lighting and is used in light show systems.
• Mechanically very strong multicolor RGB ground light, used for borders in parkways, entrances of
discotheques, buildings, parkings, homes, etc.
• Can also be used in al kinds of stone brick and concrete walls and ceilings.
• To be used with the LED-MANAGER (dmx power supply)
• 39 very bright LEDs behind a thick milky translucent glass cover.
• All-weather proof IP67 design with stainless steel cover ring.
• Can be built-in any concrete (or other) floors, walls and ceilings.
• Very easy electrical connection: 4-wire connection.
• 16cm overall diameter
• Longlife LED Technology!
• Power consumption = 3W only!
BEFORE USE
• Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
• Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
• Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
• Operating instructions
• LED ground light unit
SAFETY INSTRUCTIONS:
• To protect the environment, please try to recycle the packing material as much as possible.
• This unit has protection class IP67 so it can be used outdoors when it is properly installed.
• Inexperienced persons should not operate this device.
• Maximum save ambient temperature is 45°C. Don’t use this unit at higher ambient temperatures.
• The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
• The cables should always be in perfect condition: switch the LED Manager immediately off when the
cables are squashed or damaged.
• This appliance must be used with the LED Manager: don’t connect the unit to any dimmer pack or other
power supply.
• In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
• The housing and the lenses must be replaced if it is visibly damaged.
• Please use the original packing when the device is to be transported.
JB SYSTEMS® 1/20 LED GROUND LIGHT
1. Strong stainless ring with 3 bolts used to keep the glass cover safely in place.
2. Strong glass cover with rubber sealing to ensure the enclosure is waterproof.
3. 3 screws used to fix the waterproof metal body inside the plastic niche mounting box.
4. Waterproof metal enclosure with LED lights inside.
5. Plastic niche mounting box used to install the projector in the floor (or wall/ceiling)
6. 4 special “press on” wire connections.
MECHANICAL INSTALLATION
• Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Certified installation materials
should be used, the installed device should be inspected regularly for safety.
• Make sure the area around the installation place is free from unwanted persons during installation and
servicing.
• Separate the plastic niche
mounting box (5) from the rest of
the projector.
• First install the mounting box at
the right spot in the floor. See the
drawing for more information.
• Close the projector after
connecting the electrical wires
(see next chapter)
• Make sure the wire inlet on the
waterproof metal housing is well
fastened and sealed so that no
water can come in.
• Fix the metal enclosure to the niche mounting box using the 3 screws.
• Make sure the collar on the upper side of the metal housing is free from dirt or dust.
• Make sure the glass cover and its rubber sealing are clean and put them in place.
• Install the stainless metal ring and fasten with the 3 special bolts.
JB SYSTEMS® 2/20 LED GROUND LIGHT
ENGLISH OPERATION MANUAL
ELECTRICAL INSTALLATION
The electrical installation should be carried out by qualified personal only, according to the
regulations for electrical and mechanical safety in your country.
VERY IMPORTANT
its outputs! Do not exceed this maximum allowed power! To know the total power consumption of all
LED products in a chain you simply have to count up the power consumption of all units in the chain.
Check the chapter “specifications” at the end of this manual to see the power consumption of the
different LED STRIPS!
• Since the LED Manager uses special 4pin connecters on its power
outputs, we suggest to buy an optional 1m extension cable (with
special male/female 4pin connectors) and to cut the female connector.
Now you can easily strip the cable. You will find 4 colored wires inside:
• White wire: This is the common wire (anode)
• Red wire: This the power for the red LEDs (max. 50W)
• Green wire: This the power for the green LEDs
• Blue wire: This the power for the blue LEDs (max. 50W)
• Just connect these 4 wires to the corresponding 4 wires of the
projector. All projectors can be connected in parallel
drawing below. Make sure not to exceed the maximum allowed load!
: Check the user manual of the LED Manager for the maximum allowed power on
(max. 50W)
as shown on the
ENGLISH OPERATION MANUAL
OPERATING INSTRUCTIONS
Since the LED Ground light is controlled by the LED Manager, we strongly advice to read the operation
instructions in the LED Manager user manual.
MAINTENANCE
• Switch off the LED Manager and unplug the mains cable.
During inspection the following points should be checked:
• All screws used for installing the projector and any of its parts should be tightly fastened and may not be
corroded.
• When the glass cover is visibly damaged due to cracks or deep scratches, it must be replaced.
• The cables must be in impeccable condition and should be replaced immediately when even a small
problem is detected.
• Check the cable glands and the sealing rubber around the glass cover if you see water on the inside of the
projector.
• The unit can be cleaned with the normal floor cleaning products.
SPECIFICATIONS
Connections: 4 colored wires with “press on” connections
IP-protection: IP67
Operation voltage : 24Vdc common anode
Power consumption: 3Watt (39 LEDs)
Weight: 1,5kg
Size: see drawing below
• For longer distances you can extend the cables with a normal 4x1,5mm²
electrical installation cable. If you can’t find a cable with the same color codes we
strongly suggest you write down the color transitions between both cables! (ex.
white Æ black, blue Æ blue, green Æ brown, …) This is extremely important
otherwise the projectors will not work as expected.
• When you install several projectors, you will surely need special waterproof
junction boxes to make the junctions needed.
• Another option is to open the waterproof metal enclosure (4) and to replace the
original cable by your own cable. In this case you can make the connection
immediately inside the projector so you don’t need a special waterproof junction
box.
• After checking that the maximum allowed power is not exceeded, you can connect the cable, coming from
the projectors, to one of the outputs of the LED Manager.
Example power calculation: You have to install 47x LED GROUND LIGHT
chain can be connected to one of the LED Manager outputs since it does not exceed the allowed 150W. The
maximum number of Ground lights connected to the LED Manager = 2x 50pcs = 100pcs.
Æ
47x3W = 141Watt. This
JB SYSTEMS® 3/20 LED GROUND LIGHT
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS® 4/20 LED GROUND LIGHT
Loading...