Module Model Name: AXD-Y1
This module AXD-Y1 is the dual-band 2.4GHz and 5GHz bands Wi-Fi module which is
compliant with IEEE802.11a/b/g/n/ac specification.
Bluetooth (BT) compliant with the BT specification version 4.2 (BLE).
2. Electrical
Chipset: The module main chipset: APQ8009, PM8916, QCA6174A
Supply: The module source all required power from a 4.3V +/- 0.3V input supply.
3. Environmental
Operating Temperature: The module operate across the temperature range of -10°to
55°Celsius
4. OEM/Integrators Installation Manual:
Important Notice to OEM integrators
1. This module is limited to OEM installation ONLY.
2. This module is limited to installation in mobile or fixed applications, according to
Part 2.1091(b).
3. The separate approval is required for all other operating configurations, including
portable configurations with respect to Part 2.1093 and different antenna
configurations
4. For FCC Part 15.31 (h) and (k): The host manufacturer is responsible for additional
testing to verify compliance as a composite system. When testing the host device for
compliance with Part 15 Subpart B, the host manufacturer is required to show
compliance with Part 15 Subpart B while the transmitter module(s) are installed and
operating. The modules should be transmitting and the evaluation should confirm
that the module's intentional emissions are compliant (i.e. fundamental and out of
band emissions). The host manufacturer must verify that there are no additional
unintentional emissions other than what is permitted in Part 15 Subpart B or
emissions are complaint with the transmitter(s) rule(s).
The Grantee will provide guidance to the host manufacturer for Part 15 B
requirements if needed.
End Product Labeling
When the module is installed in the host device, the FCC/IC ID label must be visible
through a window on the final device or it must be visible when an access panel,
door or cover is easily re-moved. If not, a second label must be placed on the outside
Antenna
No.
Brand
Model
Gain(dBi)
Antenna
Type
Frequency
Range
(GHz to
GHz)
Cable
Length
(mm)
1(External)
Laird
EMN2449A2S-16MHF1
3.15
PCB
dipole
antenna
2.4-2.4835
160
1(External)
Laird
EMN2449A2S-16MHF1
3.38
PCB
dipole
antenna
5.15-5.25
160
1(External)
Laird
EMN2449A2S-16MHF1
3.38
PCB
dipole
antenna
5.25-5.35
160
of the final device that contains the following text: “Contains FCC ID: UFEAXD-Y1”
“Contains IC: 6652A-AXDY1 “
The FCC ID/IC ID can be used only when all FCC/IC compliance requirements are met.
Antenna Installation
(1) The antenna must be installed such that 20 cm is maintained between the
antenna and users,
(2) The transmitter module may not be co-located with any other transmitter or
antenna.
(3) Only antennas of the same type and with equal or less gains as shown below may
be used with this module. Other types of antennas and/or higher gain antennas may
require additional authorization for operation.
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC/IC
authorization is no longer considered valid and the FCC ID/IC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate
FCC/IC authorization.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module. The end user manual shall include all required
regulatory information/warning as show in this manual.
5. Tested antenna information:
1(External)
Laird
EMN2449A2S-16MHF1
3.51
PCB
dipole
antenna
5.47-5.725
160
1(External)
Laird
EMN2449A2S-16MHF1
3.23
PCB
dipole
antenna
5.725-5.85
160
2(External)
Laird
EMN2449A2S-34MHF1
3.15
PCB
dipole
antenna
2.4-2.4835
340
2(External)
Laird
EMN2449A2S-34MHF1
3.38
PCB
dipole
antenna
5.15-5.25
340
2(External)
Laird
EMN2449A2S-34MHF1
3.38
PCB
dipole
antenna
5.25-5.35
340
2(External)
Laird
EMN2449A2S-34MHF1
3.51
PCB
dipole
antenna
5.47-5.725
340
2(External)
Laird
EMN2449A2S-34MHF1
3.23
PCB
dipole
antenna
5.725-5.85
340
6. Regulation information:
6.1 USA—Federal Communications Commission (FCC)
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
CAUTION: (this only applicable to 5GHz device)
High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to
5.85 GHz bands. These radar stations can cause interference with and/or damage this
device.
System integrators must include the FCC ID on the end product.
6.2 Canada - Industry Canada (IC)
Industry Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement."
The device could automatically discontinue transmission in case of absence of
information to transmit, or operational failure. Note that this is not intended to
prohibit transmission of control or signaling information or the use of repetitive
codes where required by the technology.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
The maximum antenna gain permitted for devices in the bands 5250–5350 MHz and
5470–5725 MHz shall comply with the e.i.r.p. limit; and
The maximum antenna gain permitted for devices in the band 5725–5825 MHz shall
comply with the e.i.r.p. limits specified for point-to-point and non point-to-point
operation as appropriate.
L'appareil peut interrompre automatiquement la transmission en cas d'absence
d'informations à transmettre ou de panne opérationnelle. Notez que ceci n'est pas
destiné à interdire la transmission d'informations de contrôle ou de signalisation ou
l'utilisation de codes répétitifs lorsque cela est requis par la technologie.
Le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en
intérieur afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles
par satellite dans le même canal;
Le gain d'antenne maximal autorisé pour les dispositifs dans les bandes 5250-5350
MHz et 5470-5725 MHz doit être conforme à la norme e.r.p. limite; et
Le gain d'antenne maximal autorisé pour les appareils de la bande 5725-5825 MHz
doit être conforme à la norme e.i.r.p. les limites spécifiées pour un fonctionnement
point à point et non point à point, selon le cas.
CAN ICES-3(B)/ NMB-3(B)
6.3 Radiation Exposure Statement
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.