Insignia NS-DVL64C1 Quick Start Manual
Quick Setup Guide | NS-DVL64C1
64-LED On-Camera Video Light
PACKAGE CONTENTS
• 64-LED On-Camera Video Light
• Quick Setup Guide
FEATURES
• 64 bright white LEDs illuminate your subject
• Daylight color temperature for natural lighting
• Integrated mount attaches to any camera or camcorder with a hot-shoe
• Threaded mounting hole for easy attachment to a tripod.
• Built-in light diuser softens the light
• Uses four AA batteries (not included)
INSTALLING THE BATTERIES
1 Slide the battery compartment lock switch to
the right.
2 Put a coin in the battery compartment opening
notch and pry outward to open the compartment.
3 Install four AA batteries in the battery
compartment, noting the + and - orientation.
4 Replace the battery compartment cover and
lock it.
Before using your new product, please read these instructions to prevent any damage.
Front view
1/4" bracket
mounting hole
Back view
Battery
compartment
lock
LEDs
Locking ring
Camera hotshoe
connection
Battery compartment
lock/unlock switch
Brightness
controller
Power switch
DC power jack
SETTING UP YOUR VIDEO LIGHT
1 Loosen the locking ring by turning it
counterclockwise.
2 Slide the light onto the hot-shoe of your camera
or camcorder.
3 Tighten the locking ring to secure the light to
your camera or camcorder.
Note: If your camcorder has no hotshoe connection, we
recommend that you purchase a connecting bracket for
your camcorder. The video light has a 1/4" bracket mounting hole. You can easily
connect both the light and the camcorder to a bracket.
USING YOUR VIDEO LIGHT
1 Switch the power on.
2 Turn the brightness controller to adjust the
brightness.
3 Begin capturing video or images.
Note: For extended photo shoots or recording sessions,
we recommend that you use an AC adapter (5V)
(purchased separately) instead of AA batteries.
SAFETY INFORMATION
• Do not use in high temperature or high humidity conditions.
• If this product overheats, it will cease operation and resume working only after
cooling down. This is due to the built-in overtemperature protection.
• Do not handle with wet hands, immerse in water, or expose to rain.
• Observe precautions when handling batteries:
• Do not mix new and used batteries or batteries of dierent types.
• Do not put batteries into a re or apply direct heat to it.
• Batteries are prone to leakage when fully discharged. To avoid damage to the
product, be sure to remove batteries when the product will not be used for a
long time or when batteries run out of charge.
• Should liquid from batteries come into contact with skin or clothing, rinse
immediately with fresh water.
SPECIFICATIONS
Dimension (L×W×H)
Net weight
Battery
DC power supply
Power (Max.)
Color temperature
Brightness
Brightness control
LED quantity
Operation temperature
*Operation hours: With four Alkaline batteries, when the brightness is adjusted
100%, the operation hours is 2 hours. When the brightness is adjusted to 50%,
operating time will be about 3.5 hours. The brightness will diminish gradually
beyond these run times.
**Product design and specications are subject to change without notice.
3.4 × 3.4 × 1.4 in. (8.5 × 8.5 × 3.5 cm)
4.5 ounces (127.1 g)
Four AA batteries (Alkaline or NiMH)
5V
<4.5W
5600±300K
>1000Lux (0.5m)
Stepless
64
14~104° F (-10~40° C)
LEGAL NOTICES
FCC Caution
Changes or modications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
ONEYEAR LIMITED WARRANTY
For complete warranty, visit www.insigniaproducts.com.
CONTACT INSIGNIA
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies. Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2015 Best Buy. All rights reserved. Made in China
V1 ENGLISH 15-0059
Loading...