User Guide | Guide de l’utilisateur | Guía del Usuario
14” and 20” Flat Panel TV
TV à écran plat de 14 et 20 po | TV de panel plano de 14” y 20”
NS-14FTV/20FTV
Insignia-A5-Blank page.fm Page 1 Thursday, January 5, 2006 4:47 PM
Welcome
Congratulations on your purchase of a high-quality Ins ig nia produ ct .
Your NS-14FTV or NS-20FTV color TV represents the state of the art
in color television design, and is designed for reliable and trouble-free
performance.
Risk of electric shock. Do not open. Do not attempt to service your
TV yourself because opening or removing covers may expose you
to dangerous electrical voltage or other hazards. Re f e r all se rvicing
to qualified service personnel.
To reduce the risk of fire or electric shoc k, do not e xpo se your TV to
rain or moisture. Do not expose your TV to dripping or splashing
liquids. Do not set obj ects fil led with li quids , suc h as v ases , on y our
TV.
To avoid fire, do not place an open flame source, such as a lighted
candle, on your TV.
Leave at least 4.0 inches (10 cm) space around your TV for
sufficient ventilation.
Do not block the ventilation openings with items, such as
newspapers, tablecloths, curtains, or similar items.
In case of smoke, strange noises, or strange smells from your TV,
turn it off, unplug it from the wall outlet, and contact your dealer or
service center.
www.insignia-products.com
1
NS-14FTV/NS-20FTV Col
TV
Read instructions
Read all safety and operating instructions before operating your TV.
Retain instructions
Keep the safety and operating instructions for future reference.
Heed warnings
Follow to all warnings on your TV and in the operating instructions.
Follow instructions
Follow all operating and use instructions.
Outdoor antenna grounding
If an outside antenna or cable system is connected to TV, make sure
that the antenna or cable system is grounded to provide some
protection against voltage surges and built-up static charges. Section
810 of the National Electrical Code (NEC), ANSI/NFPA 70, provides
information with respect to correct grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
or
7
6
2
5
4
3
1
1Electric service equipment
2Power service grounding electrode system
3Ground clamps
4Grounding conductors
5Antenna discharge unit
6Grounding clamp
7Antenna lead in wire
2
www.insignia-products.com
NS-14FTV/NS-20FTV Col
TV
Cleaning
Unplug your TV from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning the
exterior cabinet only.
Lightning
To protect your TV from a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to
your TV from lightning and power line surges.
Power cord protection
Route power supply cords so they are not likely to be walked on or
pinched by items placed on or against them. Pay particular attention
to cords at plugs, wall outlets, and the points where they exit from
your TV.
Water and moisture
Do not use your TV near water (for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool).
Ventilation
Slots and openings in the cabinet back or bottom are provided for
ventilation, to ensure reliable operation of your TV, and to protect it
from overheating. These openings must not be blocked or covered.
Do not place your TV on a bed, sofa, rug, or other similar surface. Do
not place your TV near or over a radiator or heat source. Do not place
your TV in a built-in installation, such as a bookcase or rack, unless
you provide correct ventilation or follow the manufacturer's
instructions.
Power source
Operate your TV only from the type of power source indicated on the
rating plate. If you are not sure of the type of power supply to your
home, consult your TV dealer or local power company.
Moving your TV
If you move your TV from a cold place to a warmer place, wait until
the condensation inside the TV has evaporated completely before
you turn it on.
Sunlight
Position your TV so the screen is not exposed to direct sunlight.
Viewing environment
Use soft, indirect lighting while watching your TV. A completely dark
environment and reflection from the screen may cause eye fatigue.
Magnetic interference
Keep your TV away from high magnetic fields, such as powered
speakers, to avoid affecting the tint.
or
www.insignia-products.com
3
NS-14FTV/NS-20FTV Col
TV
Maintenance
Use an isolated power transformer during maintenance because your
TV chassis may be electrified.
Note to cable system TV installer
This reminder is provided to call the cable TV system installer's
attention to Article 820-40 of the NEC that provides guidelines for
correct grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
Features
Front
The location of features may vary depending on your TV model.
or
Power
button
Input button
INPUT
Menu button
Volume down
button
4
VOL
MENU
www.insignia-products.com
Remote
sensor
Power
indicator
VOL
CH
CH
Channel
up button
Channel
down button
Volume
up button
NS-14FTV/NS-20FTV Col
or
TV
FeatureDescription
Power buttonPress to turn your TV on or off.
Power indicatorTurns red when your TV is in Standby m ode.
Remote control sensorReceives signals from the remote control. Do
INPUT buttonPress to select the video input.
MENU buttonPress to open the TV on-screen display
VOL button
VOL button
CH button
CH button
not block.
(OSD).
Press to decrease the volume.
Press to increase the volume.
Press to change to a channel with a lower
number.
Press to change to a channel with a higher
number.
Back
The type and location of jacks may vary depending on your TV model.
For more information, see “Specifications”.
Antenna jack
L
R
S-Video
input jack
www.insignia-products.com
Audio input
jacks
5
NS-14FTV/NS-20FTV Col
TV
Side
or
The location of the jacks may vary depending on your TV model.
Video input jack
L
Audio input jacks
R
Headphone jack
6
www.insignia-products.com
NS-14FTV/NS-20FTV Col
TV
Remote
or
MUTE
Number/letter
DISPLAY
AUDIO
CCD
CH
VOL
Power
RECALL
PICTURE
SLEEP
INPUT
VOL
MENU
CH
www.insignia-products.com
7
NS-14FTV/NS-20FTV Col
TV
ButtonDescription
MUTEPress to mute the sound.
or
Number/letterPress to enter channel numbers and date
DISPLAYPress to display channel information.
AUDIOPress to select one of the preset audio
CCDPress to turn closed captioning on or off.
CH
VOL
POWERPress to turn your TV on and off. If your TV is
settings directly through the remote control.
To enter a two-digit channel, press the two
digits. To enter a three-digit channel, press
and hold the first digit for two seconds until
two dashes appear to the right of the number,
then press the secon d and third numbers. For
example, to tune channel 123, press a nd hol d
1 for two seconds, press 2, then press 3.
modes.You can select STANDARD, NEWS,
MUSIC, or MEMORY. You can set up your
own sound mode preferences and save them
under the MEMORY sound mode.
When you are wa tching y our TV, press to tune
to a higher-numbered T V channel.
When you are using the OSD, press to select
a menu or menu option.
When you are watching your TV, press to
decrease the volume.
When you are using the OSD, press to scroll
down through menu options.
in Standby (power saving) mode, pre ss to exit
Standby mode.
RECALLIf you are watching your TV, press to return to
PICTUREPress one or more times to select one of the
SLEEPPress to access sleep timer settings.
8
the previous channel you were watching.
If you are using the OSD, press to return to
the previously displayed menu.
preset picture modes. You can select
STANDARD, DYNAMIC, MILD, or MEMORY.
You can set up your own picture mode
preferences and save them under the
MEMORY picture mode.
www.insignia-products.com
NS-14FTV/NS-20FTV Col
or
TV
ButtonDescription
INPUTPress to select the video input signal.
VOL
MENUPress to open the on-screen display (OSD).
CH
When you are watching your TV, press to
increase the volume.
When you are using the OSD, press to scroll
up through menu options.
When you are wa tching y our TV, press to tune
to a lower-numbered TV channel.
When you are using the OSD, press to select
a menu or menu option.
Installing remote control batteries
Warning
Caution
Do not throw the batteries into fire. Dispose of used batteries as
hazardous waste.
Do not drop or disassemble the remote control. Do not get the
remote control wet.
To install batteries in the remote control:
1 Remove the battery cover.
2 Insert two AAA batteries into the battery compartment. Make sure
that the +/– symbols on the battery match the +/– marks inside the
battery compartment.
3 Replace the battery cover.
Note
When the remote control will not be used for a long period of ti me
or when the batteries are worn out, remove the batteries to prevent
leakage.
www.insignia-products.com
9
NS-14FTV/NS-20FTV Col
TV
Setting up your TV
Connecting cable TV or a VHF/UHF external antenna
or
Caution
To connect cable TV or a VHF/UHF external antenna:
1 Connect a 75 Ohm cable to the antenna jack on the back of your
2 Connect the other end of the 75 Ohm cable to cable TV or an
Do not bind the antenna cable and the power cord together.
TV.
external VHF/UHF TV antenna.
Note
10
If you use a 300 flat feeder, you need to connect a 300/75 Ohm
converter to the 300 flat feeder, then connect the converter to your
TV antenna jack.
We recommend using a 75 Ohm cable to reduce interference
caused by radio waves.
www.insignia-products.com
NS-14FTV/NS-20FTV Col
or
TV
Connecting a standard video device
If your model has audio jacks on the side, use the following illustration
to connect a standard video device to the side jacks.
Non-S-Video
device
Yellow
(to video output)
White
Red
(to audio output)
Yell ow
White
Red
Headphones
www.insignia-products.com
11
NS-14FTV/NS-20FTV Col
TV
Connection an S-Video device
S-Video
device
S-Video
output
White
Red
or
White
Red
S-Video
jack
12
www.insignia-products.com
NS-14FTV/NS-20FTV Col
or
TV
Using your TV
Turning your TV on and off
To turn your TV on and off:
1 Plug the power cord into an electrical outlet.
2 Press the Power button on your remote control.
Note
The power indicator turns off when your TV is active.
The power indicator turns red when the your TV is in Standby
mode. When your TV has a blue screen or is tuned to a channel
that does not have a signal, your TV goes into Standby mode after
five minutes.
Changing TV channels
To change TV channels:
•Press the CH or CH button on your remote control or TV.
To enter channel numbers and date settings directly:
•To enter a two-digit channel number, press the two numbers.
•To enter a three-digit channel number, press and hold the first
number for two seconds until two dashes appear to the right of
the number, then press the second and third numbers. For
example, to tune channel 123, press and hold 1 for two
seconds, press 2, then press 3.
Adjusting the volume
To adjust the volume:
•Press the VOL or VOL button on your remote control or
press the VOL or VOL button on your TV.
Setting the sleep timer
To set the sleep timer:
1 Press the SLEEP button on your remote control one or more times
to select the amount of time you want the TV to wait before
automatically turning off. You can select 30 minutes, 60 minutes,
90 minutes, or 120 minutes.
2 To cancel the SLEEP timer, press the SLEEP button one or more
times until SLEEP OFF appears.
www.insignia-products.com
13
NS-14FTV/NS-20FTV Col
TV
Selecting the picture mode
To select the picture mode:
•Press the RECALL button on your remote control one or more
times to select the picture mode. You can select STANDARD,
DYNAMIC, MILD, or MEMORY. You can set up your own
picture mode preferences and save them under the MEMORY
picture mode.
Selecting the sound mode
To select the sound mode:
•Press the AUDIO button on your remote control one or more
times to select the audio mode. You can select STANDARD,
NEWS, MUSIC, and MEMORY. You can set up you own sound
mode preferences and save them under the MEMORY sound
mode.
Setting up parental controls
To set up parental controls:
1 Open the OSD, select the FUNCTION menu, then select the
V-CHIP option. For more information, see “Using the on-screen
display (OSD)”.
2 Press the VOL button on your TV or the VOL button on your
remote control.
3 Enter your four-digit password. The default password is 0358.
or
14
www.insignia-products.com
NS-14FTV/NS-20FTV Col
or
TV
4 Press the VOL or VOL button on your remote control to select
the MPAA (movie) rating you want to block. The rating you
selected and all other ratings higher than the rating you selected
are blocked.
You can select:
•N/A–No rating.
•G–General. Appropr i ate for all children.
•PG–Parental guidance suggested.
•PG13–Parental guidance. Content not appropriate for
children under 13 years of age.
•R–Restricted. Content not appropriate for children under 17
years of age without parental super vi si on.
•NC-17–Content not appropriate for children under 17 years
of age.
•X–Adults only.
5 Press the VOL or VOL button on your remote control to select
the TVPG (TV program) rating you want to block. The rating you
selected and all other ratings higher than the rating you selected
are blocked.
You can select:
•TY7–All child r en
•TVY7–Children seven years of age and older
•TV-G–General audiences
•TV-PG–Parental guidance suggested
•TV-14–Parental guidance strongly suggested
•TV-MA–Mature audiences
6 Press the VOL or VOL button on your remote control to select
CONTENT THEMES to block TV programs with certain types of
content.
You can select:
•D–Sexually explicit dialog
•FV–Fantasy violence
•L–Adult language
•S–Sexual situations
•V–Violence
Tip
To return to a previous menu, select .
www.insignia-products.com
15
NS-14FTV/NS-20FTV Col
TV
Using the on-screen display (OSD)
Your TV has an on-screen display (OSD) that you use to adjust your
TV settings.
To use the OSD:
1 Press the MENU button on your remote control or TV to open the
OSD.
2 Press the MENU button again to select a menu.
3 Press the CH or CH button on your remote control or TV to
select an option.
4 Press the VOL or VOL button on your remote control or the
VOL or VOL button on your TV to change the option.
5 Press the MENU button on your remote control or TV one or more
times to close the OSD.
OSD menus and options
MenuOption
or
PictureCONTRAST–Increases the picture level to
adjust the white areas of the picture .
Decreases the picture le v e l t o adju st the b lac k
areas of th e picture.
BRIGHTNESS–Increases the brightness to
add more light to dark areas of the picture.
Decreases the brightness to add more dark to
light areas of the picture.
COLOR–Adjusts the overall color of the
picture.
SHARPNESS–Increases the sharpness level
to show cleaner and clearer images.
Decreases the level to show a smoother
picture.
TINT–Increases the color le vel to add more
green to skin tones. Decreases the color le vel
to add more red to skin tones.
COLOR TEMP–Selects a preset color
temperature. You can select NORMAL,
WARM, or COLD.
COMB FIL TER–Turns the comb filter o n or off .
The comb filter isolates the brightness and
color signal transmissions to improve the
picture. This option is only available on some
models.
16
www.insignia-products.com
NS-14FTV/NS-20FTV Col
or
TV
MenuOption
SoundVOLUME–Increases and decreases the
TuningCHANNEL–Selects the T V channel. Press
FUNCTIONLANGUAGE–Changes the OSD language.
volume.
TREBLE–Adjusts the treble.
BASS–Adjusts the bass.
BALANCE–Adjusts the balance between the
right and left speaker jacks.
SURROUND–Turns surround sound on or off.
the volume buttons on the remote control or
TV or use the number buttons to enter the
channel number.
DELETE CH–Deletes the TV channel listed in
the CHANNEL option. If you select YES, the
channel is deleted from the channel l is t. If you
select NO, your TV changes to the channel
listed in the CHANNEL option.
SOURCE–Selects the source of the TV
signal. Select AIR for a VHF/UHF antenna.
Select CABLE for a cable TV connection.
AUTO SEARCH–Scans the channels for
available signals, then creates and stores a
channel list.
SCREEN–Selects the screen background
when the TV is on and not receiving a signal.
You can select OFF, BLUE BACK, or SAVER.
CHILD LOCK–Turns the parental locks off
and on. When you select thi s option, y ou mu st
enter a four-digit password. The default
password is MUTE+999.
CCD–Selects the closed captioning mode.
You can select OFF, C1, C2, C3, C4, T1, T2,
T3, or T4.
V-CHIP–Sets up the V-Chip to block and
unblock TV programs. For more information,
see “Setting up parental controls”.
www.insignia-products.com
17
NS-14FTV/NS-20FTV Col
TV
Specifications
NS-14FTV
or
Receiving
system
FunctionsSide/Front A/V
Sound output1 W
Power supply120 V AC
Remote
control
batteries
Rated power
consumption
Dimensions
W × D × H
Weight24.25 lbs.
TV: NTSC
AV: NTSC3.58 @ 60 Hz
S-Video
Headphone
CCD
V-Chip
Parental lock
AV stereo
Picture shows
a double or
triple image,
but the sound
is clear
Picture has
lines (waves)
and the
sound is
distorted
No soundMake sure that the volume is turned up
No picture
and no sound
Picture has
no color
Make sure that the outside antenna is
connected correctly.
Reposition the outside antenna.
The multiple image is called “ghosting.”
Connect your TV to an outside antenna.
Make sure that you use good quality
cables and terminations.
Reposition the outside antenna.
Electrical interference can be caused by
cars and motorcycles.
Electrical interf eren ce ca n a ls o be c aus ed
by fluorescent lamps and other
appliances.
Try plugging your TV into a different
electrical outlet, preferably an outlet on a
different circui t.
and the mute control is turned off.
Make sure that the power cord is plugged
into a working outlet.
Make sure that the brightness and
contrast level are not set too low.
Adjust the color controls.
Picture is
scrambled
Picture has
spots
20
Change the channel.
Color can be affected by moving your TV,
turning on appliances like a vacuum
cleaner near your TV, or placing magnets
too close to your TV.
T urn off y our TV using the P o wer b utton on
the TV (not on the remote control). Leave
your TV off for at least 15 minutes.
If the picture still has spots, turn off your
TV combo and leave it off overnight.
www.insignia-products.com
NS-14FTV/NS-20FTV Col
TV
Maintenance
Unplug your TV from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners.
Wipe the exterior with a soft cloth dampened with water. Do not spay
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions in this manual, may cause harmful interference to
radio communications.
or
Caution
Caution
Pursuant to 47CFR, Part 15.21 of the FCC rules, any changes or
modifications to this device not expressly approved by the
manufacturer could cause harmful interference and would void the
user's authority to operate this device.
This is a CLASS B prod uct . In a do me sti c environment this product
may cause radio interference, in which case the user may be
required to take adequate measures to counter interference.
www.insignia-products.com
21
Loading...
+ 53 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.