Infinity TSS-FMK4000 User Manual

TOTAL SPEAKER SOLUTIONS
TSS-4000
TSS-FMK4000
Owner’s Guide
The TSS-FMK4000 allows you to recess a TSS-SAT4000 or TSS-CENTER4000 into the wall. When installed, the speaker will extend beyond the wall approximately 1."
Unpacking the Components
Finish unpacking the flush-mount kit and check the contents. If you suspect damage from transit, report it immediately to your dealer. Keep the shipping carton and packing materials for future use.
Contents
Please verify that the package contains the following items:
(1) 3/16"-Thick Cardboard Template
(2) End Brackets
2
TSS-FMK4000
(1) Speaker Frame
(2) Sealing Strips
(2) Mounting Blocks
(4) #8 x 1" Flat-Head Wood Screws
(4) #8 x 1-1/8" Pan-Head Wood Screws
(2) 1/4-20 x 3/4" Flat-Head Machine Screws
Important Notes:
1) In order to horizontally flush-mount the TSS-CENTER4000 in a wall with standard 16" spacing between the studs, some modification to that area of the wall will be necessary.This type of installation will require a professional licensed contractor to install horizontal braces that comply with the customer’s local building codes.
satellite installation, follow all the steps but cut the hole
2) For a in a vertical direction, perpendicular to the floor. See exploded view on page 7.
Step One
Remove both end caps of the speaker by unscrewing the single center screws.
Speaker
1/4-20 x 3/4" Flat-Head Machine Screw
End Bracket
End Cap
Center Screw 1/4-20 x 3/4" Screw
Step Two
Attach both of the end brackets to the speaker ends with the 1/4-20 x 3/4" flat-head machine screw, as shown.
End Bracket
1/4-20 x 3/4" Flat-Head Machine Screw
TSS-FMK4000
3
Step Three
After you have found the correct placement on the wall for the speaker, use the template provided to draw the exact-sized hole required. Make sure to use a level when positioning the template to ensure that your installation is level. Then cut out the drywall to create the hole.
Wall
Template
Screw Holes
NOTE: The hole for the speaker should be 22-1/2" x 4-3/8."
Step Four
Place the mounting blocks inside the hole at either end. Use two #8 x 1" flat-head wood screws to secure them in place.
Mounting Block
(4) #8 x 1" Flat-Head Wood Screws
Mounting Block
4
TSS-FMK4000
Step Five
Attach speaker wires as described in the speaker’s owner’s manual and, using four #8 x 1-1/8" pan-head wood screws provided, screw the speaker assembly into place, making sure that the screws anchor themselves into the mounting blocks behind the drywall.
(4) #8 x 1-1/8" Pan-Head Wood Screws
Step Six
Apply the sealing strips to either side of the speaker to cover the remaining openings of the cutout in the drywall.
Sealing Strip
TSS-FMK4000
5
Step Seven
Remove the paper cover from the gasket on the speaker-facing side of the frame. Place the frame over the in-wall assembly and snap it into place.
Remove Paper Cover From Gasket
Frame
6
TSS-FMK4000
Center Speaker In-Wall Installation
Satellite Installation Exploded View
For satellite installation, repeat the steps but cut the hole in a vertical direction, perpendicular to the floor.
Satellite Speaker In-Wall Installation
TSS-FMK4000
7
© 2004 Harman International Industries, Incorporated Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 516.674.4INF (USA only) www.infinitysystems.com
Infinity is a registered trademark,and Total Solutions is a trademark,of Harman International Industries, Incorporated. Part No. 400-OMINKIT 10/04
Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and construction details in this and related Infinity publications are therefore subject to change without notice.
Loading...