Model type:
WGS838TXU
Commercial code:
21626
page 1
General notes
Technical Documentation guidelines
-------------------------------------------------------------------------------------------------------------------------------
You can find herewith some generic information to simplify cunsulting of technical documentation:
1. Models of same range share the same exploded views, which report the richest set of spare parts:generally, a model does not necessarly have a
related spare part for each particular shown on exploded views.
2. Some spare parts can not be represented directly on the exploded views (instruction booklets, specific kit, etc...). You can find those codes in the
spare parts list with the same reference of particular where spares are installed or with references 099, 999. Instruction booklets, once managed,
appear with 000 reference.
3. On the higher right site of each exploded view there is a serial number which indicates the beginning of the production of certain range:some
models might have more than an exploded view for a given category, each distinguished by a different serial no.and linked to another spare parts
list, In this case, serial no. is required to supply the right spare part code. Exploded view to be considered is the one with a more recent serial no.
but previous than the one of the model that needs assistance.
4.Exploded views might require further updates even after publishing. Addition of new spares will go on following the already existing numeration
references. Revision number of an exploded view is shown into last four digits of serial number into upper right hand corner.
5.The spare parts list associated to an exploded view shows related codes of spares managed for a certain model; for each spare part other
informations are available:
REF: reference no of spare into a table; SUBSTITUTE: list of spare(s) which can replace a code but that keeps same functional characteristics
INDUSTRIAL CODE: list of variables of a model (shown into model label) where such spare is used; NOTICE: code of information(s) to refer to
complete technical intervention, track for changes or to find correct spare part code.
6. Some notices, into a same section are generic therefore cannot be directly linked to a spare part. In order to assist a model in the best way as
possible, it is helpful to pay attention to all notices and constantly verify documentation updates
7.Technical documentation cover shows model name and its commercial codes
page 2
pdf_tavola_title_ENG
cod. 1150120
page 3
Spare parts list
Spare parts list cod. 1150120
Ref. Code Substitute Industrial code Description Notice
000 C00063256 user instructions booklet gb-
001 C00057816 top - white (shiny)
002 C00044900 pilot lamp red
003 C00063257 control panel + handle
004 C00051882 1 C00044877 timer knob white 27.
005 C00044820 t/stat or dryer knob white 27.
007 C00044735 push button knob white
008 C00044769 worktop retainer
009 C00057808 cabinet white 27 n1040030
010 C00056260 1 C00065185 bolt kfrfl tcbz 4.4 x 9 zcr (wgd-
011 C00058929 door handle kit wgd
012 C00057813 door frame and glass assy
013 C00044736 plinth white giugiaro
014 C00044819 clip
015 C00002497 nut m4x3,2x7
russo
giugiaro
80525)
015 C00019845 bolt t 1/2 t m4x8
015 C00019846 bolt t 1/2 t m4x12
016 C00057567 hinge plate outer case (wgd-
017 C00051723 foot
018 C00046121 spring for foot d = 12.2
020 C00003144 blanking plug 11mm
023 C00050864 rear cover - white (shiny)
099 C00058931 spacer pvc 32mm.'als'
80525)
mm
page 4
099 C00058932 bolt + washer m6x50
page 5
pdf_tavola_title_ENG
cod. 1150210
page 6
Spare parts list
Spare parts list cod. 1150210
Ref. Code Substitute Industrial code Description Notice
001 C00051739 1 C00064786 m8 x 20 tefl. 10.9 screw
004 C00059721 belt l=1181/1187 mm h7
005 C00059723 driven pulley d = 280 mm
006 C00051736 torx m8 x 23 dri-loc screw
007 C00050879 bearing spider assembly 1000
008 C00051737 torx m8 x 27 dri-loc screw
009 C00058384 outer tank inox
010 C00051421 detergent recovery hose n1040038,n1040038
010 C00064117 detergent recovery hose l=319mmn1040038,n1040038
010 C00064583 hose clamp 55 n1040038,n1040038
011 C00050880 1 C00065464 drum als n1040048
011 C00065464 drum als-wgs n1040048
012 C00023840 bolt m6 x 80 for clamping
013 C00003018 clamping band tank front
014 C00050865 tub front stainless
016 C00051423 air trap
017 C00051325 bellows seal als
rpm
band tank front
018 C00033041 clamping ring - bellows seal
019 C00036780 bellows clamp (tank front)
020 C00037132 bolt + washer m4x12x1
020 C00058523 pillar retainer-heating element
022 C00027990 hose clamp 78-85 to tank
022 C00051729 hose clamp 50-60 to tank
front 856mm
(stainless)
page 7
023 C00051422 hose-tank to pump
024 C00030443 1 C00047136 nut romob m8
033 C00020941 seal - tank front inox
034 C00023841 nut for clamping band tank
035 C00039667 oil seal bearing + spider/tank
036 C00027923 hose dispenser to tank
038 C00026298 bearing ba2b 633667
039 C00026299 circlip 60 x 1.5
041 C00058387 upper counterweight
042 C00047136 nut romob m8
043 C00037346 nylon washer
044 C00015492 screw m8x80 t.t.l.
045 C00053819 extractable beater n1040048
045 C00065463 removable washing paddles
046 C00050881 spider drum als
048 C00038358 bolt m8x16 (dry loc)
049 C00057809 washer
050 C00060123 tank spring s/c
front
seal
30x60.03x37
40 l
n1040048
051 C00019675 anchorage pad - suspension
052 C00058388 lower counterweight
053 C00058386 bolt m8 x 12060
054 C00019849 washer 37x8,5x2
056 C00030338 shock absorber support
059 C00058389 shock absorber 120s40
061 C00030446 bolt m10 x 45 zntr
062 C00030680 1 C00040130 nut m 10
099 C00025208 counterweight pad
spring
page 8
pdf_tavola_title_ENG
cod. 1150320
page 9
Spare parts list
Spare parts list cod. 1150320
Ref. Code Substitute Industrial code Description Notice
001 C00024521 suplly cable 3x1,5 nf
001 C00064563 supply cable 3x1 schuko 1,5 m
002 C00041163 terminal block
003 C00043435 radio interference suppressor
003 C00064559 radio interference suppressor
004 C00059717 pressure swit.i/130-100 ii/225-
006 C00008663 bracket - interference
008 C00019749 indicator lamp
009 C00054735 timer eaton ec 4684
010 C00046664 bolt m4 x 6 tsp
011 C00019650 adjustable thermostat
013 C00047006 metal operating rod diverter
014 C00044800 additive cover
015 C00046423 detergent drawer (50410)
017 C00046667 wiring stop
018 C00059539 thermal door interlock
019 C00045023 filter handle
120 iii/31
suppressor
019 C00045025 filter seal
019 C00045027 filter element kit
020 C00050334 self cleaning pump 240v./50hz.
021 C00002407 washer 6,4x13x1,5
022 C00019682 rubber bush 20 mm - motor
022 C00042897 rubber bush motor
page 10
024 C00019965 spacer tube for motor support
025 C00043430 tacho generator black for ice
025 C00047317 brush for motor
025 C00059718 motor ice 850 rpm
026 C00019964 motor bolt m6 x 212 te
027 C00059719 thermostat 1t 40ø c na
028 C00014917 grommet - thermostat
029 C00051446 1 C00066454 digital module 5520 5520/u n1040060
029 C00066454 digital module 5520 5520/u
030 C00046621 dispenser body + top
032 C00019708 dispenser spring
033 C00028569 diverter quadrant 19 teeth
034 C00020880 1 C00015498 hose - valve/dispenser (hot)
035 C00028568 diverter pivot arm 18 teeth
036 C00019755 anti-vibration bush (foam)
037 C00030388 pressure switch hose 450mm.
motor
(ice)..940n2101/940n1i01
triac 12 a.
n1040060
038 C00058465 push button switch na+na on-
038 C00058466 switch nc
038 C00059722 deviator switch nc+resistor 3
041 C00059720 wiring - timer eaton ec 4684
043 C00051738 outlet hose
045 C00005781 inlet hose filter
048 C00019734 1 C00104773 electrovalve 1 way 8 lt (cold) n1040030
048 C00064046 electrovalve 1 way 8 lt (90504) n1040030
049 C00051728 electrovalve support
051 C00003070 mains inlet hose cold 25c
052 C00019902 plastic -u- to make drain hose
053 C00051730 heating element 1800w/230v
054 C00021662 dispenser cold water
099 C00052828 door seal hose clip bz 6140r
off
kohm
10bar 1500 mm
hook
+t.i.45ø
page 11
Notices
n1040030
"Snella" washing machine cabinet modification
-------------------------------------------------------------------------------------------------------------------------------
Beginning from serial no. 905043.0001, the valve support is obtained from the mould in the "Snella" washing machine cabinets produced in the
Comunanza plant.
This modification entails the elimination of the plastic valve support code 051728 as well as the handling of two new valves that differ from the
previous ones for the deeper fixing bracket (064045 double 7-liter valve and 064046 1E 1U 8-liter valve).
The new cabinets are interchangeable with the premodification ones only if the new valves are used.
n1040038
New detergent recovery hose in models produced in the Comunanza plant
-------------------------------------------------------------------------------------------------------------------------------
Beginning from serial number 90607.0001 the washers and washer-dryers produced in the Comunanza plant have been using a new detergent
recovery hose with code 064117 together with a new fixing clamp of 55 mm instead of 58 mm with code 064583.
The hose with code 051421 will be regularly managed for the Teverola appliances. In the Comunanza appliances it can be replaced with the new
hose, but not vice versa.
n1040048
New drum with tumbler ALS-WGS.
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 90927.0001, ALS WGS 600-800 and 1000 washing machines from the Snella range make use of the drum part no.
page 12
065464 which uses the tumbler part no. 065463.
The new drum complete with tumbler can be used instead of the pre-modification one but not vice-versa.
The drum part no. 050880 will be handled until the stocks have run out, whereas the tumbler part no. 053819 will continue to be handled normally.
n1040060
Remco modules with 12 A Triac
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 00217.0001, the following modules with 12 A triac have been used on appliances produced at the Comunanza / Teverola
factory:
Part no. 066454 - REMCO 5520
Part no. 066455 - REMCO 5521
Part no. 066456 - REMCO 5530
Part no. 066457 - REMCO 5531
The new modules can be used instead of the corresponding pre-modification modules, which will continue to be handled normally until stocks run
out.
Part no. 051446 - REMCO 5520
Part no. 056332 - REMCO 5521
Part no. 053085 - REMCO 5530
Part no. 056333 - REMCO 5531.
n1040030
"Snella" washing machine cabinet modification
-------------------------------------------------------------------------------------------------------------------------------
Beginning from serial no. 905043.0001, the valve support is obtained from the mould in the "Snella" washing machine cabinets produced in the
Comunanza plant.
This modification entails the elimination of the plastic valve support code 051728 as well as the handling of two new valves that differ from the
page 13
previous ones for the deeper fixing bracket (064045 double 7-liter valve and 064046 1E 1U 8-liter valve).
The new cabinets are interchangeable with the premodification ones only if the new valves are used.
n1040038
New detergent recovery hose in models produced in the Comunanza plant
-------------------------------------------------------------------------------------------------------------------------------
Beginning from serial number 90607.0001 the washers and washer-dryers produced in the Comunanza plant have been using a new detergent
recovery hose with code 064117 together with a new fixing clamp of 55 mm instead of 58 mm with code 064583.
The hose with code 051421 will be regularly managed for the Teverola appliances. In the Comunanza appliances it can be replaced with the new
hose, but not vice versa.
n1040048
New drum with tumbler ALS-WGS.
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 90927.0001, ALS WGS 600-800 and 1000 washing machines from the Snella range make use of the drum part no.
065464 which uses the tumbler part no. 065463.
The new drum complete with tumbler can be used instead of the pre-modification one but not vice-versa.
The drum part no. 050880 will be handled until the stocks have run out, whereas the tumbler part no. 053819 will continue to be handled normally.
n1040060
Remco modules with 12 A Triac
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 00217.0001, the following modules with 12 A triac have been used on appliances produced at the Comunanza / Teverola
factory:
Part no. 066454 - REMCO 5520
Part no. 066455 - REMCO 5521
Part no. 066456 - REMCO 5530
page 14
Part no. 066457 - REMCO 5531
The new modules can be used instead of the corresponding pre-modification modules, which will continue to be handled normally until stocks run
out.
Part no. 051446 - REMCO 5520
Part no. 056332 - REMCO 5521
Part no. 053085 - REMCO 5530
Part no. 056333 - REMCO 5531.
page 15
Electric schemes and links
Cod. ce000200
page 16
Legend
Legend: ce000200
AQS Aquastop electrovalve Mzbn/MTA zbn timer motor
B Buzzer N Neutral or Terminal Board
BC NC Spin cycle exclusion
BF Terminal board contact, motor fan and dryer
BP Buzzer PA High speed potentiometer
C Condensator PB Low speed potentiometer
CA Condensator PL Pure Wool
DV Switching device PM Motor Thermoprotector
EF/CL Electro-Valve Cold Water / Bleach PR Timer programmer or Pressure switch
EF/L Electro-Valve Cold Water / Wash PS Drain pump
EF/P Electro-Valve Cold Water / Prewash P1 1st level pressure cut-off switch
ER Exclude Heating Element P2 2nd level pressure cut-off switch
ET Thermostat disactivation R Heating element
EV Electrovalve Ras/RA Dryer heating element
EVA Dryer electrovalve RE Relay
EVC Hot water electrovalve RR Heating element
EVF Elettrovalvola acqua fredda RV Speed regulator
EVL Wash electrovalve S LED
heatin
P Pressure switch
EVP Pre Wash electrovalve SL Line LED
FA Antijamming filter SO Door LED
FD Delicate drying cycle thermostat SR Heating LED
FE Strong drying cycle thermostat ST Temperature selector
FRT Thermofusible Heating Element SV Speed Selector for Spin
I Inverter T Timer contacts
IA Switch On/Off TA Drying timer contacts
page 17
IC Switch N.C. - 1/2 Load TB Low Temperature Thermostat
ID Switch display TC Spider wheel earth
IE Water Saving Device TFL Flange earth
IF Switch - Spin Reduction TG Main earth
IP Door switch TH Thermostat
IR Line switch THF Operating thermostat
IS Water-stop THR Adjustable thermostat
I1..2..3.. Switches/switching devices TH1 1st temperature thermostat
L Line or Lamp TH2 2nd temperature thermostat
LB Low Level TH3 3rd temperature thermostat
LN Normal Level TM Motor earth
LS Pilot lamp TMB Main cabinet earth
M Earth-symbol TMP Motor thermal protector
MC Spin cycle motor TMS Thermostop
MI MOTOR WITH PULLEY TP Thermal protector
ML Wash cycle motor TPS Drain pump earth
MO Terminal Board TR Heating element earth
MP Door dip-switch TS Safety thermostat
MR Thermal Lock TT Timer earthing connection
MT Timer motor TTH Earthing Thermostat
MV Motor fan TV Tank earth
MV -Ras Dryer heating element ZBN Timer
page 18
Electric schemes and links
Cod. se000600
page 19
Legend
Legend: se000600
AQS Aquastop electrovalve Mzbn/MTA zbn timer motor
B Buzzer N Neutral or Terminal Board
BC NC Spin cycle exclusion
BF Terminal board contact, motor fan and dryer
BP Buzzer PA High speed potentiometer
C Condensator PB Low speed potentiometer
CA Condensator PL Pure Wool
DV Switching device PM Motor Thermoprotector
EF/CL Electro-Valve Cold Water / Bleach PR Timer programmer or Pressure switch
EF/L Electro-Valve Cold Water / Wash PS Drain pump
EF/P Electro-Valve Cold Water / Prewash P1 1st level pressure cut-off switch
ER Exclude Heating Element P2 2nd level pressure cut-off switch
ET Thermostat disactivation R Heating element
EV Electrovalve Ras/RA Dryer heating element
EVA Dryer electrovalve RE Relay
EVC Hot water electrovalve RR Heating element
EVF Elettrovalvola acqua fredda RV Speed regulator
EVL Wash electrovalve S LED
heatin
P Pressure switch
EVP Pre Wash electrovalve SL Line LED
FA Antijamming filter SO Door LED
FD Delicate drying cycle thermostat SR Heating LED
FE Strong drying cycle thermostat ST Temperature selector
FRT Thermofusible Heating Element SV Speed Selector for Spin
I Inverter T Timer contacts
IA Switch On/Off TA Drying timer contacts
page 20
IC Switch N.C. - 1/2 Load TB Low Temperature Thermostat
ID Switch display TC Spider wheel earth
IE Water Saving Device TFL Flange earth
IF Switch - Spin Reduction TG Main earth
IP Door switch TH Thermostat
IR Line switch THF Operating thermostat
IS Water-stop THR Adjustable thermostat
I1..2..3.. Switches/switching devices TH1 1st temperature thermostat
L Line or Lamp TH2 2nd temperature thermostat
LB Low Level TH3 3rd temperature thermostat
LN Normal Level TM Motor earth
LS Pilot lamp TMB Main cabinet earth
M Earth-symbol TMP Motor thermal protector
MC Spin cycle motor TMS Thermostop
MI MOTOR WITH PULLEY TP Thermal protector
ML Wash cycle motor TPS Drain pump earth
MO Terminal Board TR Heating element earth
MP Door dip-switch TS Safety thermostat
MR Thermal Lock TT Timer earthing connection
MT Timer motor TTH Earthing Thermostat
MV Motor fan TV Tank earth
MV -Ras Dryer heating element ZBN Timer
page 21
Electric schemes and links
Cod. 111279a
page 22
Legend
Legend: 111279a
AQS Aquastop electrovalve Mzbn/MTA zbn timer motor
B Buzzer N Neutral or Terminal Board
BC NC Spin cycle exclusion
BF Terminal board contact, motor fan and dryer
BP Buzzer PA High speed potentiometer
C Condensator PB Low speed potentiometer
CA Condensator PL Pure Wool
DV Switching device PM Motor Thermoprotector
EF/CL Electro-Valve Cold Water / Bleach PR Timer programmer or Pressure switch
EF/L Electro-Valve Cold Water / Wash PS Drain pump
EF/P Electro-Valve Cold Water / Prewash P1 1st level pressure cut-off switch
ER Exclude Heating Element P2 2nd level pressure cut-off switch
ET Thermostat disactivation R Heating element
EV Electrovalve Ras/RA Dryer heating element
EVA Dryer electrovalve RE Relay
EVC Hot water electrovalve RR Heating element
EVF Elettrovalvola acqua fredda RV Speed regulator
EVL Wash electrovalve S LED
heatin
P Pressure switch
EVP Pre Wash electrovalve SL Line LED
FA Antijamming filter SO Door LED
FD Delicate drying cycle thermostat SR Heating LED
FE Strong drying cycle thermostat ST Temperature selector
FRT Thermofusible Heating Element SV Speed Selector for Spin
I Inverter T Timer contacts
IA Switch On/Off TA Drying timer contacts
page 23
IC Switch N.C. - 1/2 Load TB Low Temperature Thermostat
ID Switch display TC Spider wheel earth
IE Water Saving Device TFL Flange earth
IF Switch - Spin Reduction TG Main earth
IP Door switch TH Thermostat
IR Line switch THF Operating thermostat
IS Water-stop THR Adjustable thermostat
I1..2..3.. Switches/switching devices TH1 1st temperature thermostat
L Line or Lamp TH2 2nd temperature thermostat
LB Low Level TH3 3rd temperature thermostat
LN Normal Level TM Motor earth
LS Pilot lamp TMB Main cabinet earth
M Earth-symbol TMP Motor thermal protector
MC Spin cycle motor TMS Thermostop
MI MOTOR WITH PULLEY TP Thermal protector
ML Wash cycle motor TPS Drain pump earth
MO Terminal Board TR Heating element earth
MP Door dip-switch TS Safety thermostat
MR Thermal Lock TT Timer earthing connection
MT Timer motor TTH Earthing Thermostat
MV Motor fan TV Tank earth
MV -Ras Dryer heating element ZBN Timer
page 24
Loading...