Humax T1 Users Manual

WPS

Use it as Router

LEDs on the Front Panel

Quick Start Guide

Wireless or Wired, it's n Wireless

RoamingRouter

QUANTUM T1

11111111

Internet

Modem

Electrical Outlet

3. Powering On

1. Plug in the AC power adaptor from the power connector to an electrical outlet.

2. If the power successfully turns on, a white light on the power LED is turned on.

Use only the AC power adaptor provided in this product. Using other

Note:

adaptors may damage the product.

T1 Router

Warning

1. Connect all devices before you plug any power cords into the electrical outlet.

2. Always turn o the product and network devices before you connect or disconnect any cables.

3. Hazardous electrical voltages can exist on the product and peripheral devices and can be present on any connected cables.

2. Checking the Mode

Your product has the Q-MODE switch.

Check that the switch is set to ROUTER.

After the product is successfully registered on the network, the LEDs illuminate continuously to indicate that the product is active and fully operational.

LED Operation

Power

Internet

Wireless

Ethernet

Internet, Wireless, Ethernet Blinking Resetting the system is in progress.

Note: Blue light is turned on when the roaming & mesh network is successfully congured over HUMAX

products.

White On Power is on.

White On Internet is connected.

White Blinking Firmware update is in progress.

Internet is not connected.

White On Network is connected wirelessly.

White Slow Blinking

White Fast Blinking

Blue On

Blue Slow Blinking

Blue Fast Blinking

White On Networking device is connected to the LAN port.

2 minutes.

Wi-Fi is not available.

No device is connected to the LAN port.

2 minutes.

1-1

1-2

1. Connecting the Internet

You can connect your product to the Internet over a direct WAN or through a modem.

1-1 If you access Internet by the modem such as ADSL, VDSL, cable and FTTH, plug

one end of the Ethernet cable to the Internet port of your product and the other end to the LAN port of your modem.

1-2

If you access the Internet by WAN broadband, plug the Ethernet cable to the Internet port of your product.

- With HUMAX QUANTUM Series,

you will experience seamless Wi-Fi network at any moment.

- T1, T2, T3, T3A, X1 and X3 support both roaming & mesh network, and T5, T7 and

T9 support roaming network only.

- Roaming & mesh feature is con฀gured over HUMAX products. (*)

Scan the QR code to access @@ on your mobile device.

Use it as Extender

You can congure WPS between the extender and the router.

3-1 Press the WPS buttons on both devices within 2 minutes. When WPS is

successfully congured, the blue light blinks on the Wireless LED.

Note: If you use another router other than HUMAX product, the white light

blinks on the Wireless LED, which means your extender is in repeater mode.

1. Changing the Mode

Your product has the Q-MODE switch. Slide the switch to EXTENDER.

4. Connecting the Network Devices

You can connect your network devices to the router over wired or wirelessly.

Mobile Phone

Gaming Console &

Media Sharing

Use Ethernet cables to connect your devices to the router over a wired Ethernet connection.

Note: We recommend you to connect entertainment devices such as OTT,

gaming console and IPTV to the Entertainment ports. The ports have the priority in transmitting multimedia data without transmission delay or interruption.

Electrical Outlet

2. Powering On

Extender has wireless connectivity with a third party router

* Roaming & mesh network is congured over HUMAX products

T1 Extender

3-2 Check the network when the connection is complete.

If you connect the extender to a HUMAX router, both network

names are the same as if they congure a single network. But, if you use a router other than HUMAX products, the network name of your extender will copy the router›s name following Ext2G or Ext5G. (ex. Router_Ext5G)

Q-MODE

Your product supports Q-MODE that enables operating as a router or an extender.

It’s very simple to change the operation mode. Just slide the Q-MODE switch to ROUTER or EXTENDER. Then, the mode change is automatically completed.

BOTH

*Roaming Mode

*Mesh Mode

ROUTER

WISP Mode

EXTENDER

edoM retuoR

AP Mode Repeater Mode Media Bridge Mode

Internet Connection

You can congure the network over a wired Ethernet connection or wirelessly.

Wired

Connect the Ethernet cable between the PC and the LAN port of your product.

Wireless

1. Open the web browser.

2. Enter http://dearmyrouter.net to the address bar, and then press the Enter key.

3. The default ID and password are admin and nnnn. nnnn is the last 4 digits of serial number. Refer to the serial number at the bottom of your product.

Note: We recommend you to change the ID and password to secure your network.

Go to Management > Change Password to change your password.

Welcome to QUANTUM T1!

http://dearmyrouter.net

192.168.1.1

Password

! For the default ID and password, see the bottom of the product.

admin

****

Model: QUANTUM T1 Code: 4-00021

Power Input: 12V , 0.5A

123456789

S/N: QT1YYWWnnnnnn

Mac: DCDC8321000001

※Please change Login Password and Wi-Fi Password for Security.

Router Login:

http://dearmyrouter.net

ID: admin Password: nnnn

SSID:

We Love You So Much

Password: humax_nnnn

When you log in to the router for the rst time, the installation wizard will appear. Then, follow the steps to congure the network.

Router Mode

1. Welcome

Click Start. The system will check automatically if your router is connected to the Internet.

Welcone to Quantum T1 !

This is Quantum T1,

 Complies with 11n Wi-Fi standard.  Wi-Fi 300 Mbps speed.  Provides WEP 64/128-bit, WPA, WPA2 and WPA-Mixed security.  Supports Guest Network ,QoS, Parental Control, VPN, WPS etc.  Supports Smart Roaming for Mobile Client.  Supports Power Saving, LED Control, System Restart for energy saving.

You can more easily set various functions through web UI and experience fabulous router.

Do you want to start the wizard for easy setup?

Start

Note:

• If you want to skip the installation wizard, click Skip. This button is available always during

installation wizard.

• We recommend you to update the rmware to the latest version when available.

3. Wireless Network Setting

Enter your own network name and password to change the default settings. You can secure your wireless network from unauthorized users.

Wireless Setting

2.4GHz

Network Name (SSID)

We Love You So Much

Password

**********

? About wireless security and password. view more

Previous Next

4. Password Setting

Enter your ID and password to change the default password. You can enhance the security on your network environment.

Change Password (Optional)

WISP Mode

You can use wireless Internet service in Router mode.

1. Log in to dearmyrouter.net, and then go to Management > WISP Mode.

2. Set the WISP mode to On, and select your Internet service provider.

WISP Mode

In this mode, all Ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in Ethernet ports share the same IP to ISP through wireless LAN.

On/O

Select the device and enter the password to connect the host device.

Network Name (SSID) CH RSSI Security MAC Address Band

Password

BC:76:70:7C:5C:74

F8:D1:11:5C:84:BA

70:7C:F8:D1:11:55

11:5C:54:D8:33:98

70:7C:F8:D1:11:55

5C:74:31:AB:C1:D2

**********

ConnectBack

We Love You So Much

TIANA_89

ASUS

Wafya

NETGEAR

iptime

-47

-51

-26

-51

-77

WPA2-PSK

None

WPA2-PSK

WEP

WPA2-PSK

-45

Refresh

2.4GHz

2-1. Roaming & Mesh

Just press the WPS buttons on HUMAX products within 1 second. Then, they are connected each other automatically, and congure the mesh network. You will experience seamless Wi-Fi roaming over the mesh network.

Roaming & Mesh Setting

HUMAX each other two products that you want to connect to, you can simply Extended Network via the WPS button.

Place the product on where to actual use, press the WPS button on your product.

Tip!

Minimizing the walls, furniture, appliances, etc. to connect between the two products, and the products work best when operating at up to 12m (40 feet) inside and outside.

If the existing congured, pressing the WPS button on the Mesh Network products

and add new products are the closest connection automatically.

WPS

Start WPS Process...

2. Internet Setting

You can connect the Internet automatically or manually depending on your Internet connection type.

Note: This page appears only when your product is not connected to the Internet.

Internet Setting

You can manually congure your connection settings.

If you do not know the Internet connection type, please contact your ISP.

Connection Type

? What is the Dynamic IP/Static IP/PPPoE/PPTP/L2TP? view more

Previous Next

Select the connection type your ISP is using. In most cases, it will be Dynamic IP.

• Dynamic IP: The Internet will be connected automatically.

• Static IP: Enter the IP address, Subnet mask, Gateway and DNS server supplied by the ISP.

• PPPoE: Enter the user name and password supplied by the ISP.

• PPTP or L2TP: Enter the user name, password and VPN server supplied by the ISP.

Note: For more information on the Internet connection, refer to the web manual at

www.humaxdigital.com/QUANTUM.

If your router is successfully connected to the Internet, the information on the internet connection will display.

Internet Setting

Connection Type WAN IP Address Subnet Mask Gateway Primary DNS Secondary DNS

Dynamic IP ▼

Dynamic IP

100.1.1.1

255.255.255.0

192.168.1.1

0.0.0.0

If you change the password, you can make your network more secure.

For the default ID and password, see the bottom of the product.

The changed password will be applied from the next login.

Current Password

New Password

Retype New Password

admin

**********

Previous Next

5. Summary

When you complete your network settings, the information on your network will display.

Summary

Internet

Wireless 2.4GHz

Previous Done

FCC warning:

Any Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

Connection Type

IP Address

Network Name (SSID)

Password

Dynamic IP

100.1.1.1

We Love You So Much

humax_0000

Extender Mode

Slide the Q-MODE switch to EXTENDER.

T1 operates as an extender, and congures the roaming & mesh network with a HUMAX router.

 T1 works automatically in AP mode if you connect it to a router over a wired Ethernet cable and use a

client device wirelessly.

 T1 works automatically in media bridge mode if you connect it to a router wirelessly and use a client

device over a wired Ethernet cable.

 T1 works automatically in repeater mode if you connect it wirelessly to a router other than a HUMAX

router and use a client device wirelessly.

 If T1 works together with a HUMAX router, the roaming & mesh network is congured over the

products.

1. Welcome

If you congure the network with HUMAX products only, click HUMAX Products and go to 2-1. Roaming & Mesh.

Welcome to Extended Network

Your product has changed to Extender mode. In this mode, you can expand Wi-Fi coverage.

If you want to congure the network over a wired Ethernet connection,

plug the Ethernet cable into the WAN port of your product.

In this case, the product operates automatically in Bridge mode.

Select a product you want to connect wirelessly.

HUMAX Products Other Products

If you use a third party product other than HUMAX, click Other Products and go to

2-2 Repeater.

2-2. Repeater

If you have a networking device other than HUMAX products, select it from the list and then enter the password. You will experience stronger and wider Wi-Fi signal.

Repeater Setting

Select a device from the list below and enter the password to connect to the host device. Using the WPS button on both devices, you can easily connect them.

If you want to congure the network over a wired Ethernet connection, plug the Ethernet cable into the WAN Port of the host device. In this case, the host operates automatically in Bridge mode.

Network Name (SSID) CH RSSI Security MAC Address Band

Password

BC:76:70:7C:5C:74

F8:D1:11:5C:84:BA

70:7C:F8:D1:11:55

11:5C:54:D8:33:98

5C:74:31:AB:C1:D2

**********

IPTime Zone

TIANA_89

ASUS

Wafya

iptime

-47

-51

-26

-77

WPA2-PSK

None

WPA2-PSK

-45

NextBack

WPS

2.4GHz

5GHz

Home

After completing the network settings, go to Operation Mode. In this page, you can see the current status of your product.

Home

This page shows the current status and some basic settings of the device.

2.4G

Dynamic IP

10.10.10.1

Internet

Operation Mode

Connection Status

IP Address

Subnet Mask

Gateway

DNS Server

MAC Address

QUANTUM T1

Router Mode

Dynamic IP

183.99.19.131

255.255.255.128

183.99.19.129

168.126.63.1/168126.63.2

F4:28:53:35:C3:F9

SanULTRA DUAL_1 4 Devices