Humanscale eFloat Installation Instructions Manual

INSTALLATION INSTRUCTIONS

PARTS REQUIRED

eFloat Parts

A (1) Top Frame (consists of two separate weldments)

B (2) Legs

C (2) Feet

D (1) Smart Controller - 7.3” (186.2 mm) x 3.9" (100.4 mm)

E (1) Touchpad (Analog or Digital)

(1) Power cord - 78.7”(2000 mm) - Not shown

(2) Motor cords - Not shown

F (8) M8 x 35 mm Button Head Socket Screw

G (8) M8 x 20 mm Flat Head Socket Screw

H (12) #5 x 55 mm Flange Head Wood Screw

I (12) #5 x 25 mm Flat Countersunk Head Wood Screw

J (15) #4.5 x 20 mm Pan Head Wood Screw

K (10) Cable Clip

L (1) Support Bar

D

Analog

E

Digital

A

C

B

Tools Required

5 mm Hex Key

6 mm Hex Key

#2 Phillips Screwdriver

Box Knife

Tape Measure

L

Hardware

F

G

H

I

J

K

2

SAFETY AND CLEANING INSTRUCTIONS

You must read the user manual carefully before installing or operating the eFloat table

The two legs and smart controller can handle a maximum load of 220 lbs including the weight of the top frame (12 lbs) and
work surface (varies).

Do not open the table legs or control components under any circumstances. There is danger of electric shock.

The eFloat table is not designed for continuous operation. Changing the desktop position without interruption for a period longer than
two minutes will result in the Controller pausing operation for eighteen minutes to prevent overheating.

Caution

Danger

eFloat may only be operated with a mains electricity supply of 120V/60Hz.

Only use the power cord supplied with the table. Check that it is not damaged. Do not operate the table if the power cord is damaged.

Before connecting and disconnecting handswitches, you must unplug the power cord.

Do not lift the legs by their motor cable as this may damage them.

A 44 lb. minimum load is required for collision sensor to function.

In the event of a malfunction (e.g. if the Controller keeps adjusting the desk because a movement key has jammed), please unplug the
unit immediately.

Do not expose the Controller to moisture, drips or splashes.

When changing the desktop position, there is a risk of pinching in spite of the built-in safety sensors. Ensure that no people or objects
are located in a hazardous area while the desk is adjusting.

Do not use eFloat in a potentially explosive atmosphere.

This device is not intended for use by individuals (including children) with limited physical, sensory or mental abilities or with a lack of
experience and/or lack of expertise, unless they are supervised by a person responsible for their safety or have received instructions
from that person on how to use the Controller.

In the event of a fault, please contact Customer Service immediately. Only original spare parts may be used for repairing the
Controllers. Parts may only be replaced by qualified service technicians. Otherwise, the warranty/guarantee shall be null and void.

Do not exchange the components of one table with those from another.

Cleaning Recommendations for Legs and Frame

• Use only a soft cloth. Refrain from hard rubbing.

• Clean light stains with water. A small amount of detergent may be used, if necessary. Rinse well with cold water
immediately after cleaning.

• Stubborn stains can be cleaned using aliphatic hydrocarbons such as mineral spirits.

• Do not use scratching, abrasive agents.

• Do not use acidic or strongly alkaline detergents and surfactants.

• Do not use organic solvents which contain ester, ketone, alcohols, aromatic compounds, glycol ether, halogenated
hydrocarbons or similar substances.

3

STEP 1

Assemble LEG to TOP FRAME section

Tools: 5 mm Hex Key

• Thread LEG MOTOR CABLE into TOP FRAME opening
followed by top of LEG until LEG rests flat against TOP
FRAME mounting plate. Attach LEG to TOP FRAME using (4)
M8 x 20 mm Flat Head Socket Screws.

• Screws should be tightened in diagonal order (fig. A). Repeat
this pattern after all 4 screws are in place to ensure a tight fit.
Screws should not be tightened beyond 15 N-m of torque.

• Insert END CAP into the Top Frame opening as shown.

• Repeat actions for remaining LEG, END CAP, and TOP
FRAME section.

fig. A

1

3

4

2

STEP 2 (IF USING HUMANSCALE WORK SURFACE)

Assemble TOP FRAME to WORK SURFACE

Tools: #2 Phillips Screwdriver

• Place WORK SURFACE on floor, top down, so that the pilot
holes are visible. Line up TOP FRAME with pilot holes.

• Place the SUPPORT BAR as pictured, in the back of the work
surface, so that its slots are aligned with the holes on the TOP
FRAME.

• Use 4 (# 5 x 55 mm Flange Head Wood-Screw) screws to
fasten the SUPPORT BAR to the TOP FRAME, use 5
(5 x 18mm Flange Head Wood-Screw) to fasten the opposite
flange of the SUPPORT BAR to the WORK SURFACE.

• Use remaining #5 x 25 mm Flat Countersunk Head
Woodscrews and #5 x 55 mm Flange Head Wood Screws to
complete attaching the TOP FRAME to the WORK SURFACE.

4