Huawei
AP2030DN
Access Point
Datasheet
Huawei
AP2030DN
Access Point
Datasheet
01
Product Overview
Huawei AP2030DN is the latest-generation gigabit wall plate access point (AP) that complies with 802.11ac Wave 1 standards. It uses an
86 mm x 86 mm plate design and can be easily installed in a standard 86-type junction box. The AP2030DN's innovative design boasts
built-in antennas, a hidden indicator, and a sliding panel, applicable to environments with densely distributed small rooms, such as hotels,
dormitories, hospitals, and offices. It provides enhanced service support capabilities and features high security, simple network deployment,
automatic AC discovery and configuration, and real-time management and maintenance. The AP2030DN can connect to wireless terminals
through wireless connections or to wired terminals using wired cables. This makes it the ideal choice of customers to construct indoor
distributed networks.
AP2030DN
............................................................................................................................. //
ˉ High-speed wireless access services: supports 2.4 GHz and 5 GHz frequency bands, 2 x 2
MIMO, 300 Mbit/s at 2.4 GHz, 867 Mbit/s at 5 GHz, and a rate of up to 1.167 Gbit/s.
ˉ Multiple ports: includes one uplink GE port, four downlink FE ports, and one RJ11 phone port,
particularly suited to hotels, apartments, and offices.
ˉ Easy to install: uses an 86 mm plate design and can be easily installed in an 86-type box,
reducing costs by making full use of existing network cable resources.
ˉ Flexible mounting options: can be mounted to a ceiling or wall using the special mounting
bracket.
ˉ Pass-through wired port: users can connect to a wired port to access the Internet when
wireless connections are unavailable.
Product Features
High-speed, reliable wireless access
• 802.11ac GE access
ˉ Huawei AP uses the latest-generation 802.11ac chip with the highest performance and strongest coverage capability. It
supports the 80-MHz bandwidth mode. Frequency bandwidth increase brings extended channels and more sub-carriers for data
transmission, and a 2.16 times higher rate. With 2 x 2 MIMO support, the AP makes a major leap in Wi-Fi access from 100M to GE.
• Air port performance optimization
ˉ In high-density scenarios where many users access the network, the increased number of low-rate STAs consumes more resources
on the air port, reduces the AP capacity, and lowers user experience. Therefore, Huawei APs will check the signal strength of STAs
during access and reject access from weak-signal STAs. At the same time, the APs monitor the rate of online STAs in real time and
forcibly disconnect low-rate STAs so that the STAs can reassociate with APs that have stronger signals. Terminal access control
technology can increase air port use efficiency and allow access from more users.
............................................................................................................................... //
Huawei
AP2030DN
Access Point
Datasheet
02
• 5G-prior access
• Load balancing between APs
• Smart roaming
High level of security
• Authentication and encryption for wireless access
ˉ The APs support both 2.4G and 5G frequency bands. The 5G-prior access function enables an AP to steer STAs to the 5 GHz
frequency band first, which reduces load and interference on the 2.4 GHz frequency band, improving user experience.
ˉ After the load balancing function is enabled, the AC distributes users evenly to APs based on user quantity and traffic volume.
Traffic load is therefore balanced among APs to ensure stable AP performance.
ˉ Smart roaming technology is based on the 802.11k and 802.11v technologies and allows STAs to connect to APs with stronger
signals, improving user experience and the overall performance of the wireless network.
ˉ The APs support WEP, WPA/WPA2–PSK, WPA/WPA2–802.1x, and WAPI authentication/encryption modes to ensure security of the
wireless network. The authentication mechanism is used to authenticate user identities so that only authorized users can access
network resources. The encryption mechanism is used to encrypt data transmitted over wireless links to ensure that the data can
only be received and parsed by expected users.
• Analysis on non-Wi-Fi interference sources
ˉ Huawei APs can analyze the spectrum of non-Wi-Fi interference sources and identify them, including baby monitors, Bluetooth
devices, digital cordless phones (at 2.4 GHz frequency band only), wireless audio transmitters (at both the 2.4 GHz and 5 GHz
frequency bands), wireless game controllers, and microwave ovens. Coupled with Huawei eSight, the precise locations of the
interference sources can be detected, and the spectrum of them displayed, enabling the administrator to remove the interference
in a timely manner.
• Rogue device monitoring
ˉ Huawei APs support WIDS/WIPS, and can monitor, identify, defend, counter, and perform refined management on the rogue
devices, to provide security guarantees for air interface environment and wireless data transmission.
Flexible networking and strong environmental adaptability
• Automatic radio calibration
ˉ Automatic radio calibration allows an AP to collect signal strength and channel parameters of surrounding APs and generate AP
topology according to the collected data. Based on interference from authorized APs, rogue APs, and non-Wi-Fi interference
sources, each AP automatically adjusts its transmit power and working channel to make the network operate at the optimal
performance. In this way, network reliability and user experience are improved.
• Adaptive bandwidth management
ˉ The AP can automatically adjust bandwidth allocation based on the user quantity and environments to improve user experience.
Huawei
AP2030DN
Access Point
Datasheet
03
Easy to manage and maintain
• Plug-and-Play (PnP)
• Easy to maintain
Basic Specifications
ˉ In Fit AP mode, the AP is plug-and-play and can automatically go online and load the configuration without manual intervention,
facilitating network deployment.
ˉ The AP supports Link Layer Discovery Protocol (LLDP) and can quickly identify new devices and generate network topology. The
AP can be monitored on the Network Management System (NMS), implementing fast fault location. It also supports remote
configuration delivery and one-click batch upgrade.
.......................................................................................................................... //
Hardware specifications
Technical
specifications
Power
specifications
Environmental
specifications
Item Description
Dimensions (H x W x D) 41.5 mm x 86 mm x 140 mm
Weight 0.2 kg
Uplink: 1 x GE interface (RJ45, PoE)
Interface type
LED indicator
Power input
Maximum power
consumption
Operating temperature 0
Storage temperature –40
Operating humidity 5% to 95% (non-condensing)
Altitude –60 m to +5000 m
Downlink: 4 x FE interface (RJ45)
Pass-through: 2 x RJ11 interface
Hidden LED indicator: turns on after the powered on and indicates the power-on,
startup, running, alarm, and fault status of the system.
• 12 V DC ± 10%
• PoE power supply: –48 V DC (in compliance with IEEE 802.3af/at)
8.7 W
NOTE
The actual maximum power consumption depends on local laws and regulations.
o
C to 40oC
o
C to +70oC
Atmospheric pressure 70 kPa to 106 kPa
Huawei
AP2030DN
Access Point
Datasheet
04
Item Description
Antenna type Built-in antennas (horizontal beamwidth 360°)
Antenna gain 2 dBi (2.4 GHz); 3 dBi (5 GHz)
Maximum number of VAPs
for each radio
Maximum number of users ≤ 64
Maximum transmit power
Power increment 1 dBm
8
20 dBm
NOTE
The actual transmit power depends on local laws and regulations.
2.4 GHz
802.11b (CCK): –101dBm @ 1 Mb/s; –90dBm @ 11 Mb/s
Radio
specifications
2.4 GHz
802.11g (non-HT20): –95dBm @ 6 Mb/s; –79dBm @ 54 Mb/s
2.4 GHz
802.11n (HT20): –95 dBm @ MCS0; –77 dBm @ MCS7
2.4 GHz
802.11n (HT40): –93 dBm @ MCS0; –74 dBm @ MCS7
5 GHz
802.11a (non-HT20): –94 dBm @ 6 Mb/s; –78dBm @ 54 Mb/s
Receiver sensitivity
5 GHz
802.11n (HT20): –94 dBm @ MCS0; –76 dBm @ MCS7
5 GHz
802.11n (HT40): –91 dBm @ MCS0; –73dBm @ MCS7
5 GHz
802.11ac (VTH20): –95 dBm @ MCS0NSS1; –71 dBm @ MCS8NSS1
5 GHz
802.11ac (VTH40): –91 dBm @ MCS0NSS1; –66 dBm @ MCS9NSS1
5 GHz
802.11ac (VTH80): –88 dBm @ MCS0NSS1; –63 dBm @ MCS9NSS1
Huawei
AP2030DN
Access Point
Datasheet
05
WLAN features
Software specifications
Item Description
• Compliance with IEEE 802.11a/b/g/n/ac
• Maximum rate: 1.167 Gbit/s
• Maximum Ratio Combining (MRC)
• Maximum Likelihood Detection (MLD)
• Data unit aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx only)
• 802.11 Dynamic Frequency Selection (DFS)
• Short Guard Interval (GI) in 20 MHz, 40 MHz, and 80 MHz modes
• Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-
based data processing and forwarding
• Automatic and manual rate adjustment (the rate is adjusted automatically by default)
• WLAN channel management and channel rate adjustment
• Automatic channel scanning and interference avoidance
• Service Set Identifier (SSID) hiding, support for SSIDs in Chinese
• Signal Sustain Technology (SST)
• Unscheduled Automatic Power Save Delivery (U-APSD)
• Control and Provisioning of Wireless Access Points (CAPWAP)
• Automatic access
• Hotspot2.0
• 802.11k and 802.11v smart roaming
• Fast roaming (≤ 50 ms)
Network
features
• Compliance with IEEE 802.3u
• Auto-negotiation of the rate and duplex mode; automatic switchover between the Media Dependent Interface
(MDI) and Media Dependent Interface Crossover (MDI-X)
• SSID-based VLAN assignment
• 4094 VLAN IDs (1 to 4094) and a maximum of 8 virtual APs (VAPs) for each radio
• AP control channel in tagged and untagged mixed mode
• DHCP client, obtaining IP addresses through DHCP
• Tunnel forwarding and direct forwarding
• STA isolation in the same VLAN
• Multicast Domain Name Service (mDNS) gateway protocol: supports AirPlay and AirPrint service sharing
between users of different VLANs
• Access control lists (ACLs)
• Link Layer Discovery Protocol (LLDP)
• Service holding upon CAPWAP link disconnection
• Unified authentication on the AC
• AC dual-link backup
• Soft Generic Routing Encapsulation (GRE)
• IPv6 Portal
• IPv6 Source Address Validation Improvements (SAVI)
• IPv4/IPv6 ACL
Huawei
AP2030DN
Access Point
Datasheet
06
QoS features
Security features
Item Description
• Priority mapping and packet scheduling based on a WMM profile to implement priority-based data processing
and forwarding
• WMM parameter management for each radio
• WMM power saving
• Priority mapping for upstream packets and flow-based mapping for downstream packets
• Queue mapping and scheduling
• User-based bandwidth limiting
• Adaptive bandwidth management (the system dynamically adjusts bandwidth based on the number of users
and radio environment to improve user experience)
• Airtime scheduling
• Support for Microsoft Lync APIs and high voice call quality through Lync API identification and scheduling
• Open system authentication
• WEP authentication/encryption
• WPA/WPA2-PSK authentication and encryption
• WPA/WPA2-802.1x authentication and encryption
• WPA-WPA2 authentication
• WAPI authentication and encryption
• WIDS including rogue AP and STA detection, attack detection, STA/AP blacklist and whitelist
• 802.1x authentication, MAC address authentication, and Portal authentication
• 802.11w Protected Management Frames (PMFs)
Maintenance
features
BYOD
Spectrum
analysis
• Unified management and maintenance on the AC
• Plug-and-Play (PnP): automatic ally going online and loading configurations
• Batch upgrade
• Local AP management through the serial port or using Telnet
• Real-time configuration monitoring and fast fault location using the NMS
• System status alarm
• STelnet using SSH v2
• Identifies the device type according to the Organizationally Unique Identifier (OUI) in the MAC address.
• Identifies the device type according to the User Agent (UA) information in an HTTP packet
• Identifies the device type according to DHCP options.
• The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried
in the RADIUS authentication and accounting packets.
• Identifies interference sources such as baby monitors, Bluetooth devices, digital cordless phones (at 2.4 GHz
frequency band only), wireless audio transmitters (at both the 2.4 GHz and 5 GHz frequency bands), wireless
game controllers, and microwave ovens.
• Works with Huawei eSight to locate and perform spectrum analysis on interference sources.
Huawei
AP2030DN
Access Point
Datasheet
07
Safety standards
Radio standards
EMC standards
Standards compliance
Item Description
UL 60950–1
IEC 60950–1
EN 60950–1
GB 4943
ETSI EN 300 328
ETSI EN 301 893
RSS-210
AS/NZS 4268
EN 301 489–1
EN 301 489–17
ETSI EN 60601-1-2
ICES-003
YD/T 1312.2-2004
ITU k.21
GB 9254
GB 17625.1
EN 55022
EN 55024IEC61000-4-6
IEC61000-4-2
IEEE standards
IEEE 802.11a/b/g
IEEE 802.11n
IEEE 802.11ac
IEEE 802.11h
IEEE 802.11d
IEEE 802.11e
IEEE 802.11k
IEEE 802.11u
IEEE 802.11v
IEEE 802.11w
Huawei
AP2030DN
Access Point
Datasheet
08
Security standards
Item Description
802.11i, Wi-Fi Protected Access 2 (WPA2), WPA
802.1x
Advanced Encryption Standards (AES), Temporal Key
Integrity Protocol (TKIP), and Extensible Authentication
Protocol (EAP) types:
• EAP-Transport Layer Security (TLS)
• EAP-Tunneled TLS (TTLS) or Microsoft Challenge
Handshake Authentication Protocol Version 2
(MSCHAPv2)
• Protected EAP (PEAP) v0 or EAP-MSCHAPv2
• EAP-Flexible Authentication via Secure Tunneling
(FAST)
• PEAP v1 or EAP-Generic Token Card (GTC)
• EAP-Subscriber Identity Module (SIM)
ETSI 300 019-2-1
ETSI 300 019-2-2
Environmental
standards
EMF
RoHS Directive 2002/95/EC & 2011/65/EU
Reach Regulation 1907/2006/EC
WEEE Directive 2002/96/EC & 2012/19/EU
Certifications Wi-Fi Alliance (WFA) certified 802.11a/b/g/n/ac
ETSI 300 019-2-3
ETSI 300 019-1-1
ETSI 300 019-1-2
ETSI 300 019-1-3
CENELEC EN 62311
CENELEC EN 50385
RSS-102
Huawei
AP2030DN
Access Point
Datasheet
09
AP2030DN Antenna Pattern Plots
2.4G (PHI=0) 2.4G (PHI=90)
5G (PHI=90)5G (PHI=0)
Huawei
AP2030DN
Access Point
Datasheet
10
Component Part Description
AP2030DN
220 V to 12 V
power adapter
220 V to 12 V
power adapter
220 V to 12 V
power adapter
Ordering Information
Broadband Network Terminal,AP2030DN,5*RJ45,
2*RJ11,11ac, 2*2 Double Frequency
Power Adapter
AC/DC Adapter--5degC-45degC-90V-270V-
12V/2A-Europe Standard-DC inlet
AC/DC Adapter--5degC-45degC-90V-270V-
12V/2A-UK Standard-DC inlet
AC/DC Adapter--5degC-45degC-90V-270V-
12V/2A-Australia Standard-DC inlet
Configuration
Description
AP
The mounting bracket is
included in the standard
configuration.
European standard Sold only on markets outside China.
UK standard Sold only on markets outside China.
Australian standard Sold only on markets outside China.
The standard configuration does
not include the network cable and
power supply.
Remarks
220 V to 12 V
power adapter
220 V to 12 V
power adapter
Adapter--5degC-45degC-90V-270V-12V/2A-Brazil
Standard-DC inlet
Adapter,-5degC,45degC,90V,270V,12V/2A,US
Standard/DC inlet
Brazilian standard Sold only on markets outside China.
US standard Sold only on markets outside China.
Professional Service and Support
Huawei WLAN planning tools deliver expert network design and optimization services using the most professional simulation platform
in the industry. Backed by fifteen years of continuous investment in wireless technologies, extensive network planning and optimization
experience, and rich expert resources, Huawei helps customers:
ˉ Design, deploy, and operate a high-performance network that is reliable and secure.
ˉ Maximize return on investment and reduce operating expenses.
More Information
For more information, please visit http://e.huawei.com or contact your local Huawei office.
Enterprise Services Product Overview Marketing Documentation
Copyright © Huawei Technologies Co., Ltd. 2016. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei
Technologies Co., Ltd.
Trademark Notice
, HUAWEI, and are trademarks or registered trademarks of Huawei Technologies Co., Ltd.
Other trademarks, product, service and company names mentioned are the property of their respective owners.
General Disclaimer
The information in this document may contain predictive statements including,
without limitation, statements regarding the future financial and operating results,
future product portfolio, new technology, etc. There are a number of factors that
could cause actual results and developments to differ materially from those
expressed or implied in the predictive statements. Therefore, such information is
provided for reference purpose only and constitutes neither an offer nor an
acceptance. Huawei may change the information at any time without notice.
Loading...