HP (Hewlett-Packard) Pro/10+ ISA, PCLA8205B User Manual
EtherExpress
PCLA8205B
TM
Pro/10+ ISA
Installation Guide
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use
of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent
of Hewlett-Packard Company.
Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft
Corporation.
TM
MMX
Pentium® is a registered trademark of Intel Corporation.
is a trademark of Intel Corporation.
Hewlett-Packard France
Commercial Desktop Computing Division
38053 Grenoble Cedex 9
France
©1998 Hewlett Packard Company
1 Connecting to a Netware 3.12 Server
1 Connecting to a Netware 3.12 Server
Windows for Workgroups Version 3.11
Windows for
Workgroups
Version 3.11
Requirements
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.
• Intel EtherExpress Pro 10+ ISA 10MBS Ethernet adapter card and drivers
disk.
• Vectra VL8 and VL7 Driver Name: EPRO.386 Size: 16K Date: 10/22/96.
• Vectra VE7/VE8 Driver Name: EPROODI.INS Size: 784B Date: 10/26/95.
• Novell Netware 3.12 server that supports Net BEUI, NWLink IPX/SPX,
and NWLink NetBIOS transfer protocols.
• Netware Client for DOS and MS Windows
Device Configuration
Vectra VL8 Vectra VL7 Vectra VE7/VE8
I/O Address 210-21Fh 210-21Fh 300-30Fh
Interrupt 10 10 (16-bit only) 11 (16-bit only)
• Board Connector type Auto-detect
• Force 8-bit operation Yes
• Flash chip address Disabled
• Remote boot program None
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO 10 ISA
Ethernet adapter card into an ISA slot.
2 Connect network cable media to the Intel EtherExpress card.
3 Power on the machine.
4 After booting, insert the Intel EtherExpress drivers disk Ver. 3.5”, and
execute “A:\SOFTSET2.EXE.”
5 Select “Change Adapter configuration” and verify the resource settings
1 Connecting to a Netware 3.12 Server
Windows for Workgroups Version 3.11
listed above under the heading “Device Configuration.”
6 If changes are required, save those changes and exit.
7 Remove the Intel drivers diskette, insert Netware client for DOS
and MS-Windows disk 1.
8 Execute INST_DOS.EXE. If you are using a Vectra VL8, enter yes to
accept the agreement and then continue from step 9.
If you are using a Vectra VL7 or VE8, follow the steps below and then
continue from step 16.
a Specify the settings as listed below:
• C:\NWCLIENT
•Yes
•Yes
• C:\WINDOWS
•No
• Intel Etherexpress ™ PRO/10 LAN Adapter
b Under the heading "Select the driver for your network board", insert
the Intel Etherexpress ™ PRO/10 drivers disk and set the path to
"A:\DOS\." (If you have an HP preloaded HDD, set path to "C:\Masters\LanDrv\PRO10P\DOS\)
c Press "Enter" to continue the installation.
9 Accept the default products by pressing enter, and then press “F10” to
continue.
10 Select 16-bit LAN Drivers and hit the enter key.
11 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER”
and hit enter.
12 Insert the Intel ethernet drivers diskette, set the path to “A:\DOS\” and
press enter.
13 Select “Intel EtherExpress ™ PRO/10” and press enter.
14 Accept the default settings, press “F10” to continue, and verify the
following entries for the “Installation Configuration Summary”:
❒ YES
1 Connecting to a Netware 3.12 Server
Windows for Workgroups Version 3.11
❒ C:\NOVELL\CLIENT32
❒ C:\WINDOWS
❒ 16-bit LAN drivers
❒ Intel EtherExpress ™ PRO/10
15 Press “F10” to save and continue.
16 When prompted, insert the corresponding disks to complete file transfer
and driver installation.
17 When the install utility is finished, press <CRTL><ALT><DEL> to restart
the machine.
18 After Windows loads, open the “NETWORK” folder, and double-click the
“NETWORK SETUP” icon.
19 Select the “Networks” button in the “Network Setup” and verify that
“Novell NetWare (Workstation Shell 4.0 and above)” is listed under
“Install Windows Support for the following network only:”
20 Click on “OK” twice to complete the installation.
1 Connecting to a Netware 3.12 Server
Windows for Workgroups Version 3.11
Windows 95 SR2 Requirements
• HP Vectra with Windows 95 SR2 installed.
• Intel EtherExpress Pro 10+ ISA Ethernet card and drivers disk.
• Driver Name for Vectra VL8 and VE7/VE8: NETPRO.INF Size: 12KB
Date: 4/25/97.
• Driver Name for Vectra VL7: EPRO.SYS Size: 11KB Date: 6/3/97.
• Novell Netware 3.12 server that supports Net BEUI,TCP/IP, NWLink IPX/
SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
1 Connecting to a Netware 3.12 Server
Windows 95 SR2
Vectra VL8 Vectra VL7 Vectra VE7/VE8
I/O Address 210-21Fh 210-21Fh 300-30Fh
Interrupt 10 10 11
• Board Connector type Auto-detect
• Force 8-bit operation Yes
• Flash chip address Disabled
• Remote boot program None
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress Pro10+ ISA
adapter card into an ISA slot.
2 Connect network Cable media to the Intel EtherExpress ISA card.
3 Insert a DOS bootable diskette and power on the machine.
4 After booting, insert the Intel EtherExpress drivers disk, “EtherExpress
drivers Ver. 3.5” and execute “A:\SOFTSET2.EXE.”
5 Select “Configure NIC”, and verify the resource settings listed above
under the heading “Device Configuration.”
6 If changes are required, save those changes and exit.
7 Remove the Intel EtherExpress software driver diskette and reboot the
machine.
1 Connecting to a Netware 3.12 Server
Windows 95 SR2
8 Power on the machine and allow it to boot to Windows 95 SR2.
If you are using a Vectra VL8 or VL7, go directly to step 9.
If you are using a Vectra VE7/VE8, follow the instructions below and then
go to step 16.
a Click on "Start" then "Settings" and open the "Control Panel."
b Double-click on the "Network" icon and click on "Add."
c Select "Adapter" and click on "Add."
d Click on "Have Disk", insert the Intel Etherexpress Pro10+ drivers disk
and set the path to "A:\." (If you have an HP-preloaded HDD, set path
to "C:\Masters\LanDrv\Pro10\")
e Click on "OK" and select the Intel EtherExpress ™ PRO/10+ and hit
enter.
f With the Intel Etherexpress PRO10+ listed in the "Network" window,
click on the "Identification" folder and specify your Computer Name,
Workgroup, and Computer Description. (If you do not have the required information, contact your network administrator.)
g Click on the "OK" button, approve the basic configuration and files will
copy.
9 When Windows 95 restarts, a message will appear to indicate that new
hardware has been found.
10 Click on “Next” to continue installation then insert the Intel EtherExpress
drivers disk.
11 Click on “Other Locations…”, set the path to “A:\”, and click on “Finish.”
(If you have an HP-preloaded HDD, set path to
“C:\Masters\LanDrv\Pro10\”)
12 When prompted for the file “EPRONDI.DLL”, with the Intel EtherExpress
drivers disk inserted, set the path to “A:\” and click “OK.”
(If you have an HP-preloaded HDD, set path to
“C:\Masters\LanDrv\Pro10\”)
13 Click “OK” to the “Network” dialog box to provide computer / work group
names.
14 Specify your Computer Name, Workgroup, and Computer Description.
(If you do not have the required information, contact your network
administrator.)
1 Connecting to a Netware 3.12 Server
Windows 95 SR2
15 Click on “Close” button, and files will copy.
16 When prompted for the file “NETAPI.DLL”, set the path to your Windows
95 files and click “OK.”
(For HP preloaded HDD’s, set the path to C:\WIN95.SR2\)
17 Click on the “Yes” button to finish the installation and restart your
computer.
1 Connecting to a Netware 3.12 Server
Windows 95 SR2
2 Connecting to a Netware 4.11 Server
2 Connecting to a Netware 4.11 Server
Windows for Workgroups Version 3.11
Windows for
Workgroups
Version 3.11
Requirements
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.
• Intel EtherExpress Pro 10+ ISA 10MBS Ethernet adapter card and drivers
disk.
• Vectra VL8 and VL7 Driver Name: EPRO.386 Size: 16K Date: 10/22/96
• Vectra VE7/VE8 Driver Name: EEPRODI.INS Size: 784B Date: 10/26/95
• Novell Netware 4.1 server that supports Net BEUI, NWLink IPX/SPX, and
NWLink NetBIOS transfer protocols.
• Netware Client for DOS and MS Windows
Device Configuration
Vectra VL8 Vectra VL7 Vectra VE7/VE8
I/O Address 210-21Fh 210-21Fh 300-30Fh
Interrupt 10 10 (16 bit only) 11 (16 bit only)
• Board Connector type Auto-detect
• Force 8-bit operation Yes
• Flash chip address Disabled
• Remote boot program None
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO 10 ISA
Ethernet adapter card into an ISA slot.
2 Connect network cable media to the Intel EtherExpress card.
3 Power on the machine.
4 After booting, insert the Intel EtherExpress drivers disk Ver. 3.5”, and
execute “A:\SOFTSET2.EXE.”
5 Select “Change Adapter configuration” and verify the resource settings
2 Connecting to a Netware 4.11 Server
Windows for Workgroups Version 3.11
listed above under the heading “Device Configuration.”
6 If changes are required, save those changes and exit.
7 Remove the Intel drivers diskette, insert Netware client for DOS and MS-
Windows disk 1.
8 Execute INST_DOS.EXE and enter yes to accept the agreement if using a
Vectra VL8, then continue to step 9.
If using a Vectra VL7 or VE7/VE8, follow the instructions below, then go
to step 18.
a Insert Netware Client for DOS and Windows Disk 1 and execute "A:\IN-
STALL."
b Change the settings to match the following and then option 6 to con-
tinue the installation.
• C:\NWCLIENT
•YES
•YES
• C:\WINDOWS
•No
• Intel EtherExpress ™ Pro/10 LAN Adapter (Use the driver from
the drivers disk at A:\)
c Insert the corresponding diskettes to finish the file transfer, and then
reboot the machine.
9 Accept the default products by pressing enter, and then press “F10” to
continue.
10 Select 16-bit LAN Drivers and hit the enter key.
11 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER”
and hit enter.
12 Insert the Intel ethernet drivers diskette, set the path to “A:\DOS\” and
press enter.
13 Select “Intel EtherExpress ™ PRO/10” and press enter.
14 Accept the default settings, press “F10” to continue, and verify the
following entries for the “Installation Configuration Summary”:
❒ YES
2 Connecting to a Netware 4.11 Server
Windows for Workgroups Version 3.11
❒ C:\NOVELL\CLIENT32
❒ C:\WINDOWS
❒ 16-bit LAN drivers
❒ Intel EtherExpress ™ PRO/10
15 Press “F10” to save and continue.
16 When prompted, insert the corresponding disks to complete file transfer
and driver installation.
17 When the install utility is finished, press <CRTL><ALT><DEL> to restart
the machine.
18 After Windows loads, open the “NETWORK” folder, and double-click the
“NETWORK SETUP” icon.
19 Select the “Networks” button in the “Network Setup” and verify that
“Novell NetWare (Workstation Shell 4.0 and above)” is listed under
“Install Windows Support for the following network only:”
20 Click on “OK” twice to complete the installation.
2 Connecting to a Netware 4.11 Server
Windows for Workgroups Version 3.11
Windows 95 SR2 Requirements
• HP Vectra with Windows 95 SR2 installed.
• Intel EtherExpress Pro 10+ ISA Ethernet card and drivers disk Ver. 3.5.
• Vectra VL8 and VE7/VE8 Driver Name: NETPRO.INF Size: 12KB Date:
4/25/97
• Vectra VL7 Driver Name: EPRO.SYS Size:11KB Date: 6/3/97
• Novell Netware 3.12 server that supports Net BEUI,TCP/IP, NWLink IPX/
SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
2 Connecting to a Netware 4.11 Server
Windows 95 SR2
Vectra VL8 Vectra VL7 Vectra VE7/VE8
I/O Address 210-21Fh 210-21Fh 300-30Fh
Interrupt 10 10 11
• Board Connector type Auto-detect
• Force 8-bit operation Yes
• Flash chip address Disabled
• Remote boot program None
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress Pro10+ ISA
adapter card into an ISA slot.
2 Connect network Cable media to the Intel EtherExpress ISA card.
3 Insert a DOS bootable diskette and power on the machine.
4 After booting, insert the Intel EtherExpress drivers disk, “EtherExpress
drivers Ver. 3.5” and execute “A:\SOFTSET2.EXE.”
5 Select “Configure NIC”, and verify the resource settings listed above
under the heading “Device Configuration.”
6 If changes are required, save those changes and exit.
7 Remove the Intel EtherExpress software driver diskette and reboot the
machine.
Loading...