HP LaserJet M1319 MFP Series – Copy
Copy using the automatic document feeder (ADF)
How do I? Steps to perform
1 Insert the top-end of the stack of originals into the ADF
Load originals using the automatic
document feeder (ADF)
CAUTION: To prevent damage to the product, do not use
an original that contains correction tape, correction fluid,
paper clips, or staples. Also, do not load photographs,
small originals, or fragile originals into the ADF.
Document loaded appears on the control-panel
input tray, with the media stack face-down and the first
page to be copied at the bottom of the stack.
2 Make sure that the ADF media lever is set correctly for
single-page or multiple-page documents.
3 Slide the stack into the ADF until it does not move any
farther.
display.
Document loaded
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
4 Adjust the media guides until they are snug against
the media.
1
www.hp.com
HP LaserJet M1319 MFP Series – Copy
Collate my copy job
How do I? Steps to perform
1 Press Set-up then select Copy setup.
Change the copy-collation setting for the
current job
3 Select the number of copies.
2 Use the arrow buttons to select Def Collation.
Copy setup
Def Collation
10
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
4 Press Start Copy to save the selection and
immediately start the copy job.
-or-
5 Press OK to save the selection without starting the
job.
1
www.hp.com
HP LaserJet M1319 MFP Series – Copy
Copy on both sides (Duplex)
How do I? Steps to perform
1 Load the first page of the document to be copied face-
Copy a two-sided original to a one-sided
document
down into the ADF.
2 Press Start Copy.
3 Flip the original, and then reload it into the ADF.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
4 Press Start Copy.
5 Repeat steps 1 through 4 for each page until all of the
original document pages have been copied.
1
www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I? Steps to perform
1 Load the first page of the document to be copied face-
Copying a two-sided original to a two-sided
document
down into the ADF.
2 Press Start Copy.
3 Flip the original, and then reload it into the ADF.
4 Remove the copied page from the output bin and place it
face down into the priority input tray.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
2
www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I? Steps to perform
5 Press Start Copy.
Copying a two-sided original to a two-sided
document (continued)
6 Remove the copied page from the output bin, and then
set it aside for manual collating.
7 Repeat steps 1 through 6, following the original
document page order, until all pages of the original are
copied.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
3
www.hp.com
HP LaserJet M1319 MFP Series – Copy
Copy on preprinted letterhead or forms
How do I? Steps to perform
1 On the product control panel, press Setup.
Change the default media-size setting
2 Use the arrow buttons to select System setup, and then
press OK.
3 Use the arrow buttons to select Paper setup, and then
press OK.
Paper setup
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
4 Use the arrow buttons to select Def. paper size, and then
press OK.
1
www.hp.com
Def. paper size
HP LaserJet M1319 MFP Series – Copy
How do I? Steps to perform
Change the default media-size setting
(continued)
Change the default media-type setting
5 Use the arrow buttons to select a media size, and then
press OK.
6 Press OK to save the selection.
1 On the product control panel, press Setup.
2 Use the arrow buttons to select System setup, and then
press OK.
Letter
System setup
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
2
www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I? Steps to perform
3 Use the arrow buttons to select Paper setup, and then
Change the default media-type setting
(continued)
5 Use the arrow buttons to select a media size, and then
press OK.
4 Use the arrow buttons to select Def. paper type, and then
press OK.
press OK.
Paper setup
Def. paper type
Letterhead
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
6 Press OK to save the selection.
3
www.hp.com
HP LaserJet M1319 MFP Series – Copy
Make my copy look better
How do I? Steps to perform
1 On the product control panel, press Quality to see the
Adjust the copy quality for the current job
2 Use the arrow buttons to scroll through the quality
current quality setting for the copy.
setting options.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
3 Select a setting, and then press Start Copy to save the
selection and immediately start the copy job, or press
OK to save the selection without starting the job.
1
www.hp.com
HP LaserJet M1319 MFP Series – Copy
Reduce or enlarge the image
How do I? Steps to perform
1 On the product control panel, press Reduce/Enlarge.
Reduce or enlarge copies for the current job
NOTE: If you select Custom: 25 to 400%, type a percentage
by using the alphanumeric buttons.
If you select 2 pages per sheet or 4 pages per sheet, select
the orientation (portrait or landscape).
2 Select the size to which you would like to reduce or
enlarge the copies in this job.
Adjust the default copy size
NOTE: The product can reduce copies to as little as 25% of
the original size or enlarge copies to as much as 400% of the
original size.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
3 Press Start Copy to save the selection and immediately
start the copy job, or press OK to save the selection
without starting the job.
1 Press Setup.
2 Use the arrow buttons to select Copy setup, and then
press OK.
1
www.hp.com
Copy setup
HP LaserJet M1319 MFP Series – Copy
How do I? Steps to perform
3 Use the arrow buttons to select Def. Redu/Enlrg, and
Adjust the default copy size (continued)
5 Press OK to save the selection.
then press OK.
4 Use the arrow buttons to select the option for how you
normally want to reduce or enlarge copies.
Def. Redu/Enlrg
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
2
www.hp.com
HP LaserJet M1319 MFP Series – Copy
Copy on media of different sizes and types
How do I? Steps to perform
Media sizes and types
Change the default media-size setting
Media-size settings
● Letter
● Legal
● A4
Media-type settings
● Plain
● Preprinted
● Letterhead
● Transparency
● Prepunched
● Labels
● Bond
1 On the product control panel, press Setup.
2 Use the arrow buttons to select System setup, and then press
OK.
● Recycled
● Color
● Light
● Heavy
● Cardstock
● Envelope #10
● Rough
System setup
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
1
www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I? Steps to perform
3 Use the arrow buttons to select Paper setup, and then press
Change the default media-size setting
(continued)
OK.
4 Use the arrow buttons to select Def. paper size, and then press
OK.
5 Use the arrow buttons to select a media size, and then press
OK.
Paper setup
Def. paper size
Change the default media-type setting
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
6 Press OK to save the selection.
1 On the product control panel, press Setup.
2
www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I? Steps to perform
2 Use the arrow buttons to select System setup, and then press
Change the default media-type setting
(continued)
OK.
3 Use the arrow buttons to select Paper setup, and then press
OK.
4 Use the arrow buttons to select Def. paper type, and then press
OK.
System setup
Paper setup
Def. paper type
5 Use the arrow buttons to select a media type, and then press
OK.
6 Press OK to save the selection.
3
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
www.hp.com
Loading...