HP Aruba 2930F 24G, Aruba 2930F 48G Setup Manual And Safety/regulatory Information

Aruba 2930F 24G/48G Switch Quick
Setup Guide and Safety/Regulatory
Information

Abstract

Use this guide to assist in the basic set-up of the following Aruba 2930F 24G and 48G switch models:

JL255A Aruba 2930F 24G PoE+ 4SFP+ Switch

nl

JL253A Aruba 2930F 24G 4SFP+ Switch

nl

JL256A Aruba 2930F 48G PoE+ 4SFP+ Switch

nl

JL254A Aruba 2930F 48G 4SFP+ Switch

nl

JL261A Aruba 2930F 24G PoE+ 4SFP Switch

nl

JL259A Aruba 2930F 24G 4SFP Switch

nl

JL262A Aruba 2930F 48G PoE+ 4SFP Switch

nl

JL260A Aruba 2930F 48G 4SFP Switch

nl

JL263A Aruba 2930F 24G PoE+ 4SFP+ TAA Switch

nl

JL264A Aruba 2930F 48G PoE+ 4SFP+ TAA Switch

*5200-1182*

Part Number: 5200-1182
Published: April 2016
Edition: 1

© Copyright 2016 Hewlett Packard Enterprise Development LP

The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services

are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting

an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.

Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or copying. Consistent with FAR

12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed

to the U.S. Government under vendor's standard commercial license.

Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is not

responsible for information outside the Hewlett Packard Enterprise website.

Applicable products

JL253AAruba 2930F 24G 4SFP+ Switch

JL254AAruba 2930F 48G 4SFP+ Switch

JL259AAruba 2930F 24G 4SFP Switch

JL260AAruba 2930F 48G 4SFP Switch

JL255AAruba 2930F 24G PoE+ 4SFP+ Switch

JL256AAruba 2930F 48G PoE+ 4SFP+ Switch

JL261AAruba 2930F 24G PoE+ 4SFP Switch

JL262AAruba 2930F 48G PoE+ 4SFP Switch

JL263AAruba 2930F 24G PoE+ 4SFP+ TAA Switch

JL264AAruba 2930F 48G PoE+ 4SFP+ TAA Switch

Aruba 2930F 24G/48G Switch Quick Setup Guide and
Safety/Regulatory Information

NOTE: The switch drawings in this document are for illustration only and may not match your
particular switch model.

NOTE: For switch and accessories installation information, browse to the manuals for your
switch model at www.hpe.com/networking/ResourceCenter.

Installation precautions

WARNING!

• The rack or cabinet should be adequately secured to prevent it from becoming unstable
and/or falling over.

• Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest
devices at the bottom and progressively lighter devices installed above.

CAUTION:

• Do not ship any switch in a rack without checking for restrictions in the Aruba 2930F Switches
Installation and Getting Started Guide. Otherwise, you may void the switch warranty.

• Ensure the power source circuits are properly grounded, then use the power cord supplied
with the switch to connect it to the power source.

• Use only approved power cords with your Aruba Networking Product. Please see the power
cord information in the section titled “Power cords” (page 10) of this guide for acceptable
power cords that are appropriate for this product. Failure to use approved power cords can
result in personal injury and product damage, and may void your product warranty.

• If your installation requires a different power cord than the one supplied with the switch, be
sure the cord is adequately sized for the switch’s current requirements. In addition, be sure
to use a power cord displaying the mark of the safety agency that defines the regulations
for power cords in your country. The mark is your assurance that the power cord can be
used safely with the switch and power supply.

• When installing the switch, the AC outlet should be near the switch and should be easily
accessible in case the switch must be powered off.

• Do not install the switch in an environment where the operating ambient temperature exceeds
its specification. See the section titled “Aruba 2930F Switch Safety and Regulatory

Information” (page 11).

• Ensure the switch does not overload the power circuits, wiring, and over-current protection.
To determine the possibility of overloading the supply circuits, add together the ampere
ratings of all devices installed on the same circuit as the switch and compare the total with
the rating limit for the circuit. The maximum ampere ratings are usually printed on the devices,
near the AC power connectors.

• Ensure the air flow around the switch is not restricted. Leave at least 3 inches (7.6 cm) for
cooling on the sides and rear of the switch. For other available air flow information, see the
Aruba 2930F Switches Installation and Getting Started Guide, located on the Hewlett Packard
Enterprise Information Library at www.hpe.com/networking/ResourceCenter.

Installation precautions 3

Prepare for installation

1. Unpack and check included parts:

• Switch

• Console cable

• Accessory kit (installation hardware)

• Power cord

• Documentation kit

2. Prepare for installation.

CAUTION: To avoid personal injury or product damage, review the “Installation precautions”

(page 3) before beginning the installation.

3. Power on and verify that self-test completes normally. An Aruba 2930F 24G or 48G switch
does not contain a power on/off switch. It is turned on by connecting the AC power cord to
the switch and to an AC power source.

12345

6

Port LEDs: Off after self-test unless a network cable is connected and
the port is receiving link beat.

1

Global Status LED: Green after self-test in default configuration.2

Locator/Unit-Identification LED: Off after self-test.3

Speed Mode Selected LED: Off after self-test in default configuration.4

4 Aruba 2930F 24G/48G Switch Quick Setup Guide and Safety/Regulatory Information