Simplify and make your data center change-ready. The HP 4Gb Virtual Connect Fibre Channel Module for the c-Class
BladeSystem is the simplest, most flexible connection to your SAN fabrics. The HP 4Gb VC-FC Module is a new class of
blade interconnect that simplifies server connections by cleanly separating the server enclosure from SAN, simplifies SAN
fabrics by reducing cables without adding switches to the domain, and allows you to change servers in just minutes, not days.
The HP 4Gb Virtual Connect Fibre Channel Module for c-Class BladeSystem is an innovative, new class of integrated
interconnects from HP.
Figure 1 HP 4Gb Virtual Connect Fibre Channel Module Front Bezel
1.
UID Indicator
2.
Module Health Indicator
3.
Port Configuration Status Indicator
4.
Link Status Indicator
5.
Port Activity Indicator
6.
Ports 1-4 (4Gb Fibre Channel)
What's New
Support for HP BladeSystem c3000 Enclosure
Models
HP 4Gb Virtual Connect Fibre Channel Module for c-Class BladeSystem
At A Glance
Performance
(4) 4Gb Auto-negotiating Fibre Channel uplinks connected to external SAN switches
(16) 4Gb Auto-negotiating Fibre Channel downlink ports provide maximum HBA performance
HBA Aggregation on uplinks ports using ANSI T11 standards-based N_Port ID Virtualization (NPIV) technology
Extremely low latency throughput provides switch-like performance.
Management
Managed with the Virtual Connect Ethernet Module
Does not add to SAN switch domains or require traditional SAN management
Appears as a pass-thru device to the SAN Manager
Virtual server profiles
Ability to pre-configure server I/O connections
Ability to move, add, or change servers on the fly
Once defined, SAN Administrators don't have to be involved in server changes
409513-B21
Options
HP 1/10Gb Virtual Connect Ethernet Module for c-Class BladeSystem
HP 1/10Gb-F Virtual Connect Ethernet Module for c-Class BladeSystem
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 1
HP 4Gb Virtual Connect Fibre Channel Module for c-
QuickSpecs
Overview
(4) Fibre Channel SFP's included with the Virtual Connect Fibre Channel Module
Class BladeSystem
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 2
QuickSpecs
Supported Products
HP 4Gb Virtual Connect Fibre Channel Module for c-
Class BladeSystem
Compatibility
HP ProLiant Servers
ProLiant BL c-Class
Server Blade
Enclosures
All HP ProLiant BladeSystem c-Class Server Blades with latest ROM updates
Supports all Server NIC's including LOM and Mezzanine card options
Virtual Connect requires the following minimum firmware levels:
BL460c BIOS - System ROM version 2007.05.01 or later
BL480c BIOS-System ROM version 2007.05.01 or later
BL465c BIOS - System ROM version 2007.04.05 or later
BL685c BIOS - System ROM version 2007.04.05 or later
Server Mezzanine Cards:
QLogic QMH2462 4Gb FC HBA QLogic Firmware loaded when driver is loaded. Use QLogic
BIOS version 1.26 (in Multiboot 1.63) or later
HP Emulex LPe 1105-HP 4Gb FC BIOS version 6.00a2 (3.00a4) or later
For the latest additional information on required firmware versions and to download firmware
upgrades, see the HP website
The HP BladeSystem c3000 and c7000 Enclosures have been designed up front with the Virtual
Connect Architecture in mind incorporating the HP Onboard Administrator, ILO Management, and
HP Management tools inside the Virtual Connect framework.
Virtual Connect requires the following minimum firmware levels:
http://www.hp.com/go/bladesystemupdates
.
Single and redundant Onboard Administrators - (version 2.01 or later)
Supported Configurations
HP BladeSystem c7000 Enclosure - Rear View
1.
Upper Fan System
2.
Interconnect Bays 1 /2
3.
Interconnect Bays 3 / 4
4.
Interconnect Bays 5 / 6
5.
Interconnect Bays 7 / 8
6.
On Board Administrator
7.
Lower Fan System
8.
Rear Redundant Power Complex
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 3
QuickSpecs
Supported Products
HP BladeSystem c3000 Enclosure - Front View
1.
Device Bays 1 thru 8
2.
Enclosure DVD Drive
3.
Standby Onboard Administrator (reserved for Future)
HP 4Gb Virtual Connect Fibre Channel Module for c-
Class BladeSystem
4.
Insight Display
5.
Active Onboard Administrator
1.
Local KVM interface (reserved for future)
2.
Interconnect Bay 1
3.
Active Cool Fans
4.
Interconnect Bay 2
5.
Enclosure Up-link and Service Port
6.
Enclosure Down-link
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
HP BladeSystem c3000 Enclosure - Rear View
7.
iLO/Onboard Administrator Port
8.
iLO/Onboard Administrator Port 2 (reserved for future)
9.
Power Supplies
10.
Interconnect Bay 4
11.
Interconnect Bay 3
Page 4
QuickSpecs
Supported Products
Mezzanines
Port Mapping
Port mapping differs slightly between full height and half height server blades due to the
support for additional Mezzanine cards on the full height version.
HP has simplified the processes of mapping Mezzanine ports to switch ports by providing
intelligent management tools via the Onboard Administrator and HP Insight Manager Software.
The Onboard Administrator Guide, Enclosure Setup and Installation Guide provides detailed
information on port mapping.
HP 4Gb Virtual Connect Fibre Channel Module for c-
Class BladeSystem
c7000 Half Height Server Blade
c3000 Half Height Server Blade
The following are supported configurations for the HP 4Gb Virtual Connect Fibre Channel Module. Please note that other
interconnect options can be installed in the enclosure, but they do not inherit the benefits of Virtual Connect. Switches and
Pass-Thru modules will operate per their default configurations. Any moves, adds, or changes to servers which are connected
to non-Virtual Connect modules will require reconfiguration on the LAN and/or SAN. The Virtual Connect Manager will only
manage Virtual Connect Modules.
The HP 4Gb VC-FC Module requires a Virtual Connect Ethernet Module installed in the system for management and
administration. Version 1.1 or higher firmware is required on the Virtual Connect Ethernet Module in order to configure,
manage, and administer Fibre Channel connections.
c7000 Full Height Sever Blade
c3000 Full Height Sever Blade
HP BladeSystem c7000 Enclosure
NOTE:
The following tables show a number of typical, supported configurations for an HP BladeSystem c7000 Enclosure.
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 5
HP 4Gb Virtual Connect Fibre Channel Module for c-
Stacking is only supported on Virtual Connect Ethernet Modules. The Virtual Connect Fibre
Channel modules are managed via the Virtual Connect Ethernet Modules. The Virtual Connect
firmware is dynamically mirrored between modules so all configuration data is updated
simultaneously in a stack. Fibre Channel data packets are not transmitted between modules in a
stacked configuration.
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 7
HP 4Gb Virtual Connect Fibre Channel Module for c-
QuickSpecs
Service and Support, HP Care Pack and Warranty Information
Class BladeSystem
Service and Support
This product is covered by a global limited warranty and supported by HP Services and a
worldwide network of HP Authorized Channel Partners. Hardware diagnostic support and repair is
available for three years from date of purchase. Support for software and initial setup is available
for 90 days from date of purchase. Additional support may be covered under the warranty or
available for an additional fee. Enhancements to warranty services are available through HP Care
Pack services or customized service agreements.
NOTE:
Server Blade Interconnect Limited Warranty includes 1 year Parts, 1 year Labor, 1-year
on-site support. Additional information regarding worldwide limited warranty and technical support
is available at:
HP services provide total care and support expertise with committed response designed to meet
your IT and business needs.
To fully capitalize on your HP BladeSystem servers' capabilities requires a service partner who
thoroughly understands your server technology and systems environment. HP Services, an
industry leader in provision of multi vender support solutions provides a range of support services
designed to meet the varying needs of business. Whether an SMB or large global corporation HP
has a HP BadeSystem server support offer to help you speedily deploy and maximize system
uptime.
Recommended Service
management.
Support - 3-Year, 24x7, Same Business Day, 4-Hour response coverage
Deployment Service - Installation and Start Up for HP BladeSystem Infrastructure
- simplify ProLiant solution implementation, maintenance, and
Enhanced Service
Support - -1-Year HP Proactive BladeSystem Service
Deployment Service - Enhanced Network Installation and Start-up for HP BladeSystem
Switches
Installation & Start-Up service for HP BladeSystem Infrastructure plus HP BladeSystem Enhanced
Network Installation and Start-UP as per the Customer Description and/or Data Sheet. To be
delivered on a scheduled basis 8am-5pm, M-F, excluding HP holidays.
For a complete listing of service offerings and information visit:
http://www.hp.com/services/bladesystemservices
- optimize service level to increase IT performance and availability.
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 8
QuickSpecs
Related Options
HP 4Gb Virtual Connect Fibre Channel Module for c-
Class BladeSystem
Optional Network
Cabling
4Gb Optical
Transceivers
Optical cables
Service and Support
Offerings
(SFPs)
Hardware
Short Wave
4Gb - 150m
Long Wave - 10 km
LC-LC for between 2/4Gb and 2/4Gb Fibre Channel devices
2 m LC-LC Multi-Mode Fibre Channel Cable
5 m LC-LC Multi-Mode Fibre Channel Cable
15 m LC-LC Multi-Mode Fibre Channel Cable
30 m LC-LC Multi-Mode Fibre Channel Cable
50 m LC-LC Multi-Mode Fibre Channel Cable
LC-SC for between a 1Gb and 2/4Gb Fibre Channel devices
2 m LC-SC Multi-Mode Fibre Channel Cable
5 m LC-SC Multi-Mode Fibre Channel Cable
15 m LC-SC Multi-Mode Fibre Channel Cable
NOTE:
server blades, cover the server blade and all HP branded hardware options
qualified for the server, purchased at the same time or afterwards, internal to the
server.
Hardware Services On-site Service
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years, Electronic
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
6-Hour Call to Repair, On-site Service, 7-Day x 24-Hour Coverage, 3 Years,
Electronic
Support Plus 24
Onsite HW support 24x7, 4hr response and Microsoft O/S SW Tech support
offsite, onsite at HP's discretion, 24x7 2hr response time incl. HP holidays,
Electronic
NOTE:
enclosure, power supplies and fans. HP qualified rack options are covered by
these services when installed within the same rack. HP supported c-Class
enclosure devices including pass thru, Ethernet interconnect and virtual connect
modules are also covered by the c7000 and c3000 enclosure Care Pack
services.
NOTE:
under the c7000 and c3000 enclosure Care Packs, SAN/Fabric switches carry
separate Care Packs. SAN/Fabric Switch Care Pack service level support should
always be uplifted to match existing storage or server service level.
Hardware Services On-site Service
Next Business Day On-site Service, 5-Day x 9-Hour Coverage, 3 Years,
Electronic
NOTE:
enclosure
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years, Electronic
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
6-Hour Call to Repair, On-site Service, 7-Day x 24-Hour Coverage, 3 Years,
Electronic
Installation & Start-up Services
The HP Care Pack service part numbers below for ProLiant BL c-Class
HP Care Pack services for the c7000 and c3000 Enclosure cover the
SAN/Fabric switches for the HP c-Class BladeSystem are not covered
Uplifts the Ethernet devices to the same level of service as the c-class
A7446B
AE493A
221692-B21
221692-B22
221692-B23
221692-B26
221692-B27
221691-B21
221691-B22
221691-B23
UE458E
UE459E
UE460E
UE473E
UE477E
UE478E
UE479E
UE480E
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 9
QuickSpecs
Related Options
HP 4Gb Virtual Connect Fibre Channel Module for c-
Class BladeSystem
Hp BladeSystem c-Class Infrastructure Installation and Startup Service,
Electronic
HP BladeSystem Enhanced Network Installation and Startup Service, Electronic
ProLiant BL c-Class Blade Server Hardware Installation, Electronic
ProLiant BL c-Class Enclosure and Server Blade Hardware Installation,
Electronic
NOTE:
http://www.hp.com/services/bladesystemservices
For more information, customer/resellers can contact
UE602E
UE603E
UE493E
UE494E
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 10
QuickSpecs
Technical Specifications
HP 4Gb Virtual Connect Fibre Channel Module for c-
Class BladeSystem
Shipping Dimensions
Shipping Weight
Product Specifications
Hardware
Length
Width
Height
Performance
Bandwidth
Aggregate Bandwidth
Fabric Latency
switch)
Number of Fibre
Channel Ports
External Port Type
Internal Port Type
Classes of Service
Scalability
Buffer Credits
Connectors and
Cabling
Indicators
Dimensions
Weight
Environmental Ranges
Power Specification
(intra-
352.55mm (13.88 in)
270.00mm (10.63 in)
120.65mm (4.75 in)
2.0Kg (4.4lbs)
Up to 800 MBps throughput per port
Maximum frame size 2148 bytes (2112 byte payload)
106 MB, Full Duplex @ 1-Gbps
212 MB, Full Duplex @ 2-Gbps
426 MB, Full Duplex @ 4-Gbps
Up to 8.52 GB, Full Duplex
1-Gbps to 1-Gbps < 0.6 µsec
2-Gbps to 2-Gbps < 0.4 µsec
4-Gbps to 4-Gbps < 0.2 µsec
Configured as Fabric port (F_Port),
1Gb, 2Gb or 4Gb auto- negotiating SFP ports
Configured as Fabric Node port (N_Port),
1Gb, 2Gb or 4Gb auto- negotiating
Class 2 and Class 3 Fibre Channel services
Does not contribute to the total switch limit. See the SAN Design Guide
for latest supported configurations.
8 buffer credits per port, ASIC embedded memory
SFP optical hot-pluggable transceiver with LC connector
Short-Wavelength Laser (SWL) up to 500m (1,640 ft.)
Long-Wavelength Laser (LWL) up to10km
Module locator (UID)
Module status
Link and Activity
Port Configuration Status
Length
Width
Height
1.27Kg (2.8 Lbs)
Specification
Temperature Range
Operating
Shipping
Storage
Maximum wet bulb
temperature
Relative humidity
(noncondensing)
Operating
Shipping
Storage
Specification
12V @ 3A (36 W)
**
10.5in (267.7mm)
7.5 in (92.79mm)
1.1 in (27.94mm)
10C to 35C (50F to 95F)
10C to 35C (50F to 95F)
Shipping -40C to 60C (-40F to 140F)
-20°C to 60°C (-4F to 140°F)
30C (80F)
10% to 90%
10% to 90%
10% to 95%
10C to 35C (50F to 95F)
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 11
QuickSpecs
Technical Specifications
HP 4Gb Virtual Connect Fibre Channel Module for c-
Class BladeSystem
Product Specifications
Software
Industry Standard NPIV
Support
Data Center
Connectivity
Management Features
The Virtual Connect Fibre Channel module works by aggregating
multiple FC HBA ports over a single N-port uplink through the use of
N_port_ID virtualization (NPIV). NPIV allows multiple distinguishable
identities (multiple port WWNs and port IDs) over a single N-port
connection. Most Fibre Channel SAN switch vendors have support for
NPIV in their latest firmware release. By conforming to the NPIV
standard, SAN equipment interoperability simplified. The Virtual Connect
Fibre Channel Module Provides basic 4:1, 8:1, or 16:1 NPIV Fibre
Channel concentration.
Each Virtual Connect Fibre Channel module supports a single SAN
fabric and is typically connected to a Fibre Channel switch that has been
configured to run in NPIV mode. The 4 uplink ports are speed selectable
from 1, 2, or 4Gb/s.
The setup wizard allows SAN administrators to name the fabric that
servers will connect into and set the oversubscription rate. Fibre
Channel boot parameters and WWN administration are configurable
options that can be integrated into server profiles.
In an NPIV environment, there is an initial brief login function between
the Virtual Connect Fibre Channel Module and the data center switch.
Once completed, all HBA connections appear as though they are
directly connected between the server and the SAN switch. The Virtual
Connect Fibre Channel Module appears as a pass-thru device to the
SAN, yet cables are reduced as high as 16:1
An HP 1/10Gb Virtual Connect Module must be present in order to
configure the VC FC Modules. This provides a complete Virtual Connect
Environment for the server connections.
Simple and intuitive Graphical User Interface (GUI) for defining,
configuring, and managing all elements of the Virtual Connect Domain.
Setup Wizards for initial domain installation and configuration and
network and SAN configuration.
Comprehensive administration, definition, and management of Ethernet
Networks, Shared Uplink Sets using VLANS, SAN Fabric management,
and Server Profiles
Domain Management of user accounts, enclosure, Virtual Connect
domain settings, and firmware updates
The location and status of Virtual Connect Modules in the HP c-Class
Enclosure and Onboard Administrator can be viewed from the Hardware
Status page. Including at-a-glance detailed information of the hardware
elements via mouse-over pop-up windows.
WWN Address Administration allows local administration of predefined
WWN addresses ranges to allow pre-provisioning of SAN volumes.
VC manager runs as a high-availability pair when HP 1/10Gb VCEthernet Modules are installed in adjacent bays. All configuration data is
stored in flash memory and checkpointed to the standby module.
Configurations can also be backed up to a workstation via the GUI.
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 12
QuickSpecs
Technical Specifications
HP 4Gb Virtual Connect Fibre Channel Module for c-
Class BladeSystem
Management and
Standards Support
Safety and
Compliance
Electromagnetic
Emissions
Certifications FCC Part
15 Class A
Standards
Safety Certifications
FCC Part 15 Class A
EN 55022 Class A (CISPR22 Class A)
VCCI Class A
AS/NZS 3548 Class A or AS/NZS CISPR22 Class A
MIC Class A
CE Marking
ANCI T11 N_Port ID Virtualization
FC-PH Rev. 4.3
FC-PH-2
FC-PH-3
FC-AL Rev 4.6
FC-AL-2 Rev 7.0
FC-FLA
FC-GS
FC-GS-2
FC-GS-3
FC-FG
FC-VI
FC Element MIB RFC 2837
Fibre Alliance MIB Version 4.0
UL/CUL Recognition to UL/CSA 60950-1
TUV to EN 60950-1
CB report and certificate to IEC 60950-1 with all country deviations
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
End-of-life
Management and
Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and
recycling programs in many geographic areas. For trade-in information,
please go to
please go to:
sales office. Products returned to HP will be recycled, recovered or
disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to
provide treatment information for each product type for use by treatment
facilities. This information (product disassembly instructions) is posted
on the Hewlett Packard web site at:
instructions may be used by recyclers and other WEEE treatment
facilities as well as HP OEM customers who integrate and re-sell HP
equipment.
http://www.hp.com/go/green
http://www.hp.com/go/green
http://www.hp.com/go/green
. To recycle your product,
or contact your nearest HP
. These
DA - 12673 Worldwide QuickSpecs — Version 5 — 10-1-2007
Page 13
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.