Honeywell N10230-2POS, N0524, N05230-2POS, N1024 PRODUCT DATA

N0524/N1024, N05230-2POS/N10230-2POS

NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR

FLOATING AND 2-POSITION CONTROL

PRODUCT DATA

SPECIFICATIONS

Supply voltage

N0524/N1024 24 Vac/dc -15%/+20%, 50/60 Hz

GENERAL

This non-spring return direct-coupled damper actuator provides floating and two-position control for:

• air dampers,

• VAV units,

• air handlers,

• ventilation flaps,

• louvers, and

• reliable control for air damper applications with up to

/ (5 Nm) and 2 m2 (10 Nm) (seal-less damper

1 m blades; air friction-dependent).

FEATURES

• Declutch for manual adjustment

• Adjustable mechanical end limits

• Removable access cover for direct wiring

• Mountable in any orientation

• Rotation direction and service/OFF switch

N05230-2POS/N10230-2POS

Nominal voltage N0524/N1024 24 Vac/dc, 50/60 Hz

N05230-2POS/N10230-2POS

All values stated hereinafter apply to operation under nominal voltage conditions.

Power consumption N0524/N1024 5 VA / 2 W N05230-2POS 22 VA / 2 W at 50 Hz 25 VA / 2 W at 60 Hz N10230-2POS 22 VA / 2 W at 50 Hz 25 VA / 2 W at 60 Hz

Ambient limits

Ambient operating limits -20...+60 °C (-5...+140 °F) Ambient storage limits -30...+80 °C (-22...+176 °F) Relative humidity 5...95%, non-condensing

Safety

Protection standard IP54 Protection class II as per EN 60730-1 Overvoltage category II

Lifetime

Full strokes 60000 Repositions 1.5 million

Mounting

Round damper shaft 8...16 mm Square damper shaft 6...13 mm; 45° steps Shaft length min. 41 mm

End switches (when included) Rating 5 A (resistive), 3 A (inductive) Triggering points 5° / 85°

Torque rating 5 Nm / 10 Nm Runtime for 90°

N0524 / N1024 90 sec (dc / 60 Hz ac) N0524 / N1024 110 sec (50 Hz ac) N05230-2POS 65...110 s (60/50 Hz) N10230-2POS 65...140 s (60/50 Hz)

Rotation stroke 95° ± 3° Dimensions see "Dimensions" on page 6 Weight (without cables) 450 g Noise rating 35 dB(A) max. at 1 m;

40 dB(A) for 230 Vac at 65 sec runtime

230 Vac -15%/+20%, 50/60 Hz

230 Vac, 50/60 Hz

N0524/N1024 AND N05230-2POS/N10230-2POS DAMPER ACTUATORS FOR FLOATING/2-POSITION CONTROL

PRODUCT IDENTIFICATION SYSTEM

N = non-spring return S = spring return

05 = 5 Nm 10 = 10 Nm

SmartAct

Fig. 1. Product Identification System

010 = modulating + floating 24 = 24 V floating + ON/OFF 230 = 230 V ON/OFF

equipped with two

end switches

+ ON/OFF

Contents of Package

The delivery package includes the actuator and parts 1 through 6 (see Fig. 2), plus two cable grommets and a spare cable grommet.

RUN MODES

The function selection switch (see Fig. 3) can be used to place the actuator into either of two different modes:

• Service/Off; or

• the floating/2-position run mode ("Dir" for CCW-closing

dampers or "Rev" for CW-closing dampers).

floating/2-position

Dir

MODELS

order no. supply voltage end switches torque

N05024 -N05024-SW2 2 N1024 -N1024-SW2 N05230-2POS 5 Nm N10230-2POS

24 Vac/dc

230 Vac --

BASIC FEATURES

5 Nm

10 Nm

Power-Off Behavior

If power is removed, the shaft adapter remains in position.

Service/Off

If the function selection switch is set to the "Service/Off" position, then all rotary movement is cancelled, and all control signals are ignored, thus allowing the actuator to be manually operated safely.

Floating/2-Position Run Mode

N0524

Dir

Service/Off

Rev

Fig. 2. Setting units and control elements

Legend for Fig. 2:

1) Universal shaft adapter

2) Mechanical end limits (manually adjustable)

3) Declutch button

4) Function selection switch

5) Removable access cover

6) Anti-rotation bracket

If the function selection switch has been set to one of the two floating/2-position control settings – and if the actuator is wired correspondingly (see Fig. 8, Fig. 9, and Fig. 10) – then as soon as operating power is applied, the shaft adapter will run according to the control signals applied.

Table 1 describes the behavior ("stops," rotates "CCW," or rotates "CW") of the N0524 / N1024 in dependence upon the control signals (switch "open" or "24 Vac/dc") applied to terminals 3 and 4, the function selection switch setting, and the manner in which the actuator is wired (either for floating mode: see Fig. 8; or for 2-position mode: see Fig. 9).

wiring

float.

2-pos.

Table 2 describes the behavior ("stops," rotates "CCW," or rotates "CW") of the N05230-2POS / N10230-2POS in dependence upon the control signals (switch "open" or "230 Vac") applied to terminals 1 and 3 and the function

Service/Off

Rev

Fig. 3. Function selection switch

Table 1. Behavior of N0524/N1024

control signal at switch setting

term. 3 term. 4 Dir Service/Off Rev

open open stops stops stops

open 24Vac/dc CCW stops CW 24Vac/dc open CW stops CCW 24Vac/dc open CW stops CCW 24Vac/dc 24Vac/dc CCW stops CW

Service / Off

Dir

Service/Off

Rev

EN0B-0477GE51 R0408

+ 4 hidden pages