Honeywell HZ-614, HZ-615, HZ-615C, HZ-614C User Manual

QUICK HEAT™ BLASTER

Model HZ-614, HZ-615 series

Model HZ-614C, HZ-615C series

OWNER’S MANUAL

low

power

off

QUICK

high

HEAT

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

IMPORTANT INSTRUCTIONS

1. Read all instructions before using heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surface.

If provided, use handles when moving this heater. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.

3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.

4. Always unplug heater when not in use.

5. Do not operate the heater with a damaged cord or plug or after the heater

malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.

6. Do not use outdoors.

7. This heater is not intended for use in bathrooms, laundry areas and similar moist

indoor locations.

8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from traffic areas where it will not be tripped over.

9. This heater is for use on 120 volts. The cord has a grounded plug as shown in Fig. 1. An adapter is available at retail (not included) for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a property grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

10. This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working.

11. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.

IMPORTANT SAFEGUARDS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS HEATER.

12. To disconnect the heater, first turn controls to the OFF position, then grip the plug and

pull it from the wall outlet. Never pull by the cord.

13. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.

14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surface, like a bed, where openings may become blocked.

15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or flammable liquids are used or stored.

16. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.

17. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 14 AWG minimum size and rated not less than 1875 watts.

18. The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.

19. SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS REGARDING THE PLUG ON YOUR PRODUCT

• Place the heater on a firm, level surface away from any

combustible material.

• With Power knob in the OFF position, plug the heater

into a grounded outlet.

• To turn the heater on, turn the Power knob clockwise to the

ON position. (Fig. 2).

• If you want to use the Quick Heat™ feature, turn the

Power knob to the Quick Heat™ Setting.

OPERATION

Fig. 2

COVER OF

GROUNDED

OUTLET BOX

Fig. 1

QUICK HEAT

off

QUICK HEAT™ FEATURE

• Quick Heat™ will propel a blast of warm air out of your baseboard. This can help

heat your room more quickly. You will hear a fan operating in this mode. You can also turn the Quick Heat™ setting off and the heater will operate with silent heat.

This heater is equipped with several devices and features for added protection.

• A high temperature safety control prevents overheating (Hi Limit).

• A thermal circuit breaker.

• This heater was created using a high quality safety plastic.

SAFETY FEATURES

TROUBLESHOOTING

If your heater shuts off unexpectedly or fails to operate, one of your heater safety features may have been activated to prevent overheating.

• Be sure the power cord is plugged into a working electrical outlet. The power light will illuminate.

• Check for any obstructions. If you find an obstruction, turn the heater OFF and unplug it.

• Allow the heater to cool completely, then remove the obstruction. Wait at least 10 minutes, then re-plug in the heater and follow the OPERATING INSTRUCTIONS for your unit.

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE RETURN THE HEATER TO THE PLACE OF ORIGINAL PURCHASE OR SEE YOUR WARRANTY. DO NOT ATTEMPT TO OPEN THE HEATER YOURSELF. DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE HEATER OR PERSONAL INJURY. IF YOU HAVE ANY QUESTIONS REGARDING THIS HEATER, PLEASE CALL OR WRITE:

Honeywell Consumer Relations Dept. Toll Free 1-800-332-1110 Email us at service@honeywell.com Mail questions and comments to:

Honeywell Consumer Relations Department 250 Turnpike Road Southborough, MA 01772

Please be sure to specify model number. Please visit our website at www.honeywell.com/yourhome

TROUBLESHOOTING (continued)

We recommend that the heater be cleaned at least once a month and before off-season storage.

• Turn the heater OFF and unplug it. Allow it to cool.

• Use a dry cloth only to clean the external surfaces of the heater.

DO NOT USE WATER, WAX, POLISH OR ANY CHEMICAL SOLUTION.

• Clean your heater using the above-mentioned steps, then pack the heater in its original container and store it in a cool dry place.

• This heater does not disassemble.

This product is rated 12.5 amps (1500W) at 120V, 60 Hz.

CLEANING AND STORAGE

ELECTRICAL RATINGS

FIVE YEAR LIMITED WARRANTY

You should first read all instructions before attempting to use this product.

The enclosed Customer Response card should be filled out and returned within 7 days of purchase.

This 5 year limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty.

HONEYWELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.

B. At its option, Honeywell will repair or replace this product if it is found to be defective in

material or workmanship. Defective product should be returned to the place of purchase in accordance with store policy. Thereafter, while within the warranty period defective product may be returned to Honeywell.

C. This warranty does not cover damage resulting from any unauthorized attempts to

repair or from any use not in accordance with the instruction manual.

D. Return defective product to Honeywell Consumer Products with a brief description of

the problem. Include proof of purchase and a $10 US check or money order for handling, return packing and shipping charges. Please include your name, address and a daytime phone number. You must prepay shipping charges. Send to:

Honeywell Attn: Returns Department 4755 Southpoint Drive Memphis, TN 38118 USA

+ 12 hidden pages