Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other
information contained in this document without prior notice, and the reader should in all cases consult HII
to determine whether any such changes have been made. The information in this publication does not
represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or
consequential damages resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights are reserved. No
part of this document may be photocopied, reproduced, or translated into another language without the
prior written consent of HII.
Web Address: www.honeywellaidc.com
Trademarks
Dolphin is a trademark or registered trademark of Hand Held Products, Inc. in the United States and/or
other countries.
Microsoft, Windows, Windows Mobile, Windows Phone, Windows Embedded Handheld, Windows CE,
Windows 98 Second Edition, Windows NT, Windows 2000, Windows ME, Windows XP, Windows 7,
Windows Vista, ActiveSync, Outlook, and the Windows logo are trademarks or registered trademarks of
Microsoft Corporation.
The Bluetooth trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to Honeywell.
Other product names mentioned in this manual may be trademarks or registered trademarks of their
respective companies and are the property of their respective owners.
Patents
For patent information, please refer to www.honeywellaidc.com/patents.
How to Extend Your Warranty.....................................................................................14-3
vii
viii
Preliminary Draft 6/19/13, Not for Release
1
!
Back Panel of the terminal
with the battery door and
battery removed.
Compliance Labels and Marks
!
Preliminary Draft 6/19/13, Not for Release
Dolphin 60s Terminal Agency Information
Dolphin 60s mobile computers meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe
operation is to operate them according to the agency guidelines that follow. Read these guidelines
carefully before using your Dolphin terminal.
This documentation is relevant for the following Dolphin models: 60sLU, 60sLE, 60sLP, and 60sL0.
CAUTION - Read the Guidelines for Battery Pack Use and Disposal on page 3-14 and all cautionary
markings on the battery, charging peripheral, or device using the battery before attempting to install, use, or
charge the battery. Risk of fire and burns if improperly handled. Do not open, crush, heat above 60°C
(140°F), or incinerate.
Label Locations
Model Number, Serial Number and IMEI Labels
The model (item) number, serial number, and international mobile equipment identity (IMEI) number for
the terminal are located on labels affixed to the bottom of the battery well.
Warning! To prevent possible hearing damage, do not listen at high volume levels for long periods.
LED Safety
LED Safety Statement
LEDs have been tested and classified as “EXEMPT RISK GROUP” to the Standard: IEC 62471:2006.
Caution! Do not view directly with optical instruments.
1 - 1
UL and C-UL Statement
Preliminary Draft 6/19/13, Not for Release
UL and C-UL listed: UL60950-1 2nd Edition, and CSA C22.2 No. 60950-1-07 2nd Edition.
Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the global positioning
system (GPS) hardware, GPS operating software or other GPS-related aspects of this product. UL has
only tested for the explosion, fire, shock, and casualty hazards required by the applicable hazardous
locations standards. UL certification does not cover the performance or reliability of the GPS hardware,
GPS operating software, or other GPS-related aspects of this product. UL makes no representations,
warranties, or certifications whatsoever regarding the performance or reliability of any GPS-related
functions of this product.
FCC Part 15, Subpart C, 15.247
FCC Part 22H, FCC Part 24E
FCC SAR OET 65 Supplement C
RSS 310
EN 301 489-1: V1.9.2, EN 301 489-3: V1.4.1,
EN 301 489-7: V1.3.1, EN 301 489-17: V2.2.1,
EN 301 489-24: V1.5.1,
EN 301 511: V9.0.2,
EN 301 908-1&2: V5.2.1,
EN 300 440-1: V1.6.1, EN 300 440-2: V1.4.1,
EN 300 328: V1.8.1, EN 300 330-1: V1.7.1,
EN 55022: 2010/AC: 2011 Class B,
EN 55024: 2010, EN 61000-3-2, EN61000-3-3,
EN 50360: 2001+A1:2012, EN 50360: 2001/AC:2006,
EN 61000-3-2, EN 61000-3-3,
EN 62209-1: 2006, IEC 62209-2: 2010,
EN 62311: 2008, EN 62479: 2010
Dolphin RF terminals are in conformity with all essential requirements of the R&TTE Directive
(1999/5/EC).
This product is marked with according to article 12 of the R&TTE Directive. In addition, this
product complies to 2006/95/EC Low Voltage Directive when supplied with the recommended power
supply. Honeywell shall not be liable f or use of our product with equipment (i.e ., power supplies , personal
computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.
The equipment is intended for use throughout the European Community; PAN European Frequency
Range: 2.402–2.480 GHz.
European Contact:
1 - 2
Hand Held Products Europe B.V.
Preliminary Draft 6/19/13, Not for Release
Nijverheidsweg 9-13
5627 BT Eindhoven
The Netherlands
This device complies with P art 15 of the FCC Rules. Operation is subject to the f ollowing tw o conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications . Howe v er , there is no guarantee that interf erence will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions. The user may find the following booklet helpful: “Something About Interference.”
This is availab le at FCC local regional offices . Our company is not responsible for any radio or television
interference caused by unauthorized modifications of this equipment or the substitution or attachment of
connecting cables and equipment other than those specified by our company. The correction is the
responsibility of the user. Use only shielded data cables with this system.
Caution! - Any changes or modifications not expressly approved by the grantee of this device could void the user’s
authority to operate the equipment.
Canadian Compliance
This device complies with Industry Canada license-exempt RSS standard(s). Oper ation is subject to the
following tw o conditions:
1.this device may not cause interference, and
2.this device must accept any interference, including interference that may cause undesired operation
of the device.
ICES-3(B)/NMB-3(B)
Caution! - Any changes or modifications not expressly approved by the grantee of this device could void the user’s
authority to operate the equipment.
1 - 3
Conformité à la règlementation canadienne
Preliminary Draft 6/19/13, Not for Release
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes:
1.l'appareil ne doit pas produire de brouillage, et
2.l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
ICES-3(B)/NMB-3(B)
Mise en garde! - Tout changement ou modification non expressément approuvées par le bénéficiaire de cet
appareil peut annuler l'autorisation d'utiliser l'équipement.
RF Exposure Information (SAR)
This mobile phone meets the government's requirements for exposure to radio waves. This phone is
designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF)
energy set by the Federal Communications Commission of the U.S. Government.
The exposure standard for wireless mobile phones employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/Kg and for Europe 2W/Kg.
Although the SAR is determined at the highest certified power level, the actual SAR level of the phone
while operating can be well below the maximum v alue. This is because the phone is designed to oper ate
at multiple power le vels so as to use only the poser required to reach the network. In general, the closer
you are to a wireless base station antenna, the lower the power output.
For this de vice , the highest reported SAR value for usage against the head is 0.73 W/kg, for usage near
the body is 0.73 W/kg.
While there may be differences betw een the SAR le vels of various phones and at various positions, they
all meet the government requirement.
The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels
evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone
is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid
after searching on FCC ID: HD560SLU.
SAR compliance for body-worn operation is based on a separation distance of 1.5cm between the unit
and the human body. Carry this device at least 1.5cm awa y from y our body to ensure RF e xposure le vel
remains at or below the maximum levels. To support body-worn operation, choose the belt clips or
holsters, which do not contain metallic components, to maintain a separation of 1.5cm between this
device and your body. RF exposure compliance with any of body-worn accessory, which contains metal,
was not tested and certified, and use such body-worn accessory should be avoided.
IC Radiation Exposure Statement
This EUT is compliance with SAR for general population/uncontrolled e xposure limits in IC RSS-102 and
has been tested in accordance with the measurement methods and procedures specified in IEEE 1528.
This equipment should be installed and operated with minimum distance 1.5cm between the radiator
and your body.
1 - 4
CE SAR Compliance
Preliminary Draft 6/19/13, Not for Release
This device meets the EU requirements (1999/519/EC) on the limitation of e xposure of the general public
to electromagnetic fields by way of health protection.
The limits are part of extensive recommendations for the protection of the general public. These recommendations have been developed and checked by independent scientific organization through regular
and thorough evaluation of scientific studies. The unit of measurements for the European Council’s
recommended limit for mobile devices is the “Specific Absorption Rate” (SAR), and the SAR limit is
2.0W/kg averaged o v er 10 gram of tissue . It meets the requirements of the International Commission on
Non-Ionizing Radiation Protection (ICNIRP).
For body worn operation, this device has been tested and meets the ICNIRP exposure guidelines and
the European Standard EN 62311 and EN 62209-2, for use with dedicated accessories. SAR is
measured with this device at a separation of 1.5cm to the body, while transmitting at the highest certified
output power level in all frequency bands of this device. Use of other accessories which contain metals
may not ensure compliance with ICNIRP exposure guidelines.
CE Country Codes
This equipment may be operated in:
ATBEBGCHCYCZDEDK
EEESFIFRGBGRHUIE
ITISLILTLULVMTNL
NOPLPTROSESISKTR
For European Community Users
Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Waste Electrical and Electronic Equipment Information
This product has required the extraction and use of natural resources for its production. It may contain
hazardous substances that could impact health and the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our en vironment and to diminish the pressure
on the natural resources, we encourage you to use the appropriate take-back systems for product
disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a
sound way.
The crossed out wheeled bin symbol informs you that the product should not be disposed of along
with municipal waste and invites y ou to use the appropriate separate tak e-bac k systems for product
disposal. If you need more information on the collection, reuse, and recycling systems, please
contact your local or regional waste administration. You may also contact your supplier for more
information on the environmental performances of this product.
1 - 5
China RoHS
Preliminary Draft 6/19/13, Not for Release
有毒有害物质名称及含量 (Names and Content of Hazardous Substances or Elements)
部件名称 (Parts Name)有毒有害物质或元素 (Toxic and Hazardous Substances or Elements)
o: 表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006标准规定的限量要求以下 (Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in China’s SJ/T11363-2006.)
x: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求 (Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials for this part is above the limit requirement in China’s SJ/T11363-2006. )
oooooo
oooooo
oooooo
oooooo
oooooo
oooooo
oooooo
oooooo
oooooo
oooooo
六价铬 (Cr
6+
)
多溴联苯 (PBB)多溴二苯醚 (PBDE)
Pacemakers, Hearing Aids and Other Electrically Powered Devices
Most manufacturers of medical devices adhere to the IEC 601-1-2 standard. This standard requires
devices to operate properly in an EM Field with a strength of 3V/m over a frequency range of 26 to
1000MHz. The maximum allowab le field strength emitted b y the Dolphin terminal is 0.3V/m according to
Subpart B of Part 1 of the FCC rules. Therefore, the RF from the Dolphin terminal has no effect on
medical devices that meet the IEC specification.
Hearing Aid Compatibility (HAC)
Dolphin 60s models 60sLU have been tested for hearing aid compatibility. These devices have an M3
and T3 rating. For additional HAC information, including the HAC rating for this product, please refer to
www.honeywellaidc.com.
When some wireless devices are used near some hearing devices such as hearing aids and implants,
users may detect a buzzing or humming noise. Some hearing devices are more immune than others to
this interference noise. Wireless devices may also vary in the amount of interference they generate.
The ratings for compatibility of digital wireless devices with hearing aids are described in the American
National Standards Institute (ANSI) C63.19 standard:
M-Rating: Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference
with hearing devices than phones that are not labeled. M4 is the superior/higher of the two ratings.
T-Rating: Phones rated T3 or T4 meet FCC requirements and are likely to be more usable with hearing
devices' telecoil than unrated phones. T4 is the superior/higher of the two ratings.
The more immune the hearing aid device is, the less likely one is to experience interference noise from
the wireless phone. Hearing aid devices may also be rated. Adding the ratings of the hearing aid and the
phone would determine probable usability:
• Any combined rating equal to or greater than six offers the best use.
• Any combined rating equal to five is considered normal use.
1 - 6
The ratings are not guarantees. Results will vary depending on the user's hearing device and hearing
Preliminary Draft 6/19/13, Not for Release
loss. If your hearing device happens to be vulnerable to interference, you may not be able to use this
device successfully. Trying out this device with your hearing device is the best way to ev aluate it for your
personal needs.
This device has been tested and rated for use with hearing aids for some of the wireless technologies
that it utilizes. However, there may be some newer wireless technologies used in this phone that have
not been tested yet for use with hearing aids. It is important to try the different features of this phone
thoroughly and in different locations, using y our hearing aid or cochlear implant, to determine if you hear
any interfering noise. Consult your service provider or the manufacturer of this phone for information on
hearing aid compatibility.
Microwaves
The radio in the Dolphin RF terminal operates on the same frequency band as a microwave oven.
Therefore, if you use a microwave within range of the Dolphin RF terminal you may notice performance
degradation in your wireless network. However, both your microwave and your wireless network will
continue to function.
1 - 7
1 - 8
Preliminary Draft 6/19/13, Not for Release
2
!
Preliminary Draft 6/19/13, Not for Release
Getting Started
Out of the Box
Verify that the carton contains the following items:
• Dolphin 60s mobile computer (terminal)
• 3.7V Li-ion rechargeable battery
• USB charge/communication cable
• Power adapter with regional plug adapters
• Quick start guide
• Compliance Regulatory Sheet
If you ordered accessories for your terminals, v erify that they are also included with the order. Be sure to
keep the original packaging in the event that the Dolphin terminal should need to be returned for service.
Note: Your Dolphin model may differ from the model illustrated in this guide; however, the features noted are
standard for all Dolphin 60s models with Windows® Embedded Handheld unless otherwise indicated.
Initial Setup for Dolphin 60s Terminals
Step 1. Install the Battery
Note: Before installing the main battery, read the Guidelines for Battery Pack Use and Disposal on page 3-14.
Dolphin 60s model terminals are designed for use with battery part number BAT-EXTENDED-01 (Li-ion
3.7V, 12.358 watt hour) manufactured for Honeywell International Inc.
The terminal is shipped with the battery packaged separate from the unit. Perform the steps illustrated
below to install the battery . F or inf ormation on how to remov e the battery , see Replacing the Main Battery
on page 2-12.
Ensure all components are dry prior to placing the battery in the terminal. Mating wet components may cause
damage not covered by the warranty.
Step 2. Charge the Battery
The power source for the Dolphin terminal is the 3.7V Li-ion rechargeable battery located under the
battery door on the back panel of the device. See Battery on page 3-8 for additional information on
battery storage, use, and disposal.
2 - 1
Important: Removing the battery from the terminal erases all non-persistent memory. Always power off the terminal
!
!
!
USB Door
Plug Adapter
1
3
4
2
Micro USB Port
Power
Adapter
5
Left Side Panel of Dolphin 60s
USB Charging/
Communication Cable
Preliminary Draft 6/19/13, Not for Release
before removing the battery.
Note: For information on how to remove the battery from the terminal, see Replacing the Main Battery on page 2-12.
Before Initial Use
Dolphin terminals ship with the battery significantly discharged of power. After installing the battery in the
terminal, charge the battery with a Dolphin 60s charging peripheral for a minimum of 6 hours for the
extended battery pack.
Note: Inadequate source current may interfere with effective battery charging; see Important Charging
Guidelines on page 3-11 for additional information.
We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause damage not covered by the warranty.
Dolphin 60s model terminals are designed for use with the following charging devices and cables:
60s-HB, 60s-MC, and 60s-USB ADAPTERKIT. See
Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet
components may cause damage not covered by the warranty.
Using the USB Charge/Communication Cable (Model 60s-USB ADAPTERKIT)
Dolphin 60s terminals ship with a USB Charge/Communication Cable and a power adapter with regional
plug adapters. The USB Charge/Communication cable provides two options for charging the terminal.
Use the cable in conjunction with the provided power supply adapter and plug adapter to charge the
terminal from a power outlet or connect the cable to a high-power USB port to charge from a host device.
Warning - The terminal shall only be connected to CTIA certified adapters, products that bear the USB-IF logo
or products that have completed the USB-IF compliance program when using the micro USB port as a
charging source.
Option 1: Charging from a power outlet
Use only a UL Listed power supply, which has been qualified b y Honeyw ell with an output rated at 5VDC
and 1A with the device.
2 - 2
Option 2: Charging from a high power USB port on a host device (PC)
USB Door
USB Port on Host Device
1
3
2
Micro USB
Port
USB Charging/
Communication Cable
Left Side Panel of Dolphin 60s
Preliminary Draft 6/19/13, Not for Release
Note: Charging the battery through a USB port takes more time than direct AC adapter charging. USB charging will
not take place if the terminal is drawing more current than supplied by the USB port.
Touch > Settings > System > Power to verify the battery is charging.
To access detailed information on the battery, touch > Settings > System > Battery.
Step 3. Boot the Terminal and Access the Home Screen
The terminal begins booting as soon as power is applied. Do not press any keys or interrupt the boot
process. When the boot process is complete, the Home screen appears depending on your Dolphin
model.
Note: During the initial charging stage, the terminal display may dim to conserve battery power due to inactivity.
Touch the display to turn on the backlight.
2 - 3
The Home Screen
Touch to access
the Start menu.
Touch a menu item to
access additional screens.
Title Bar (page 2-4)
Touch to access the Clock & Alarms settings screen.
Tile Bar (page 2-7)
Swipe up or down with your
finger or stylus to scroll through
the menu items.
T ouch to access the
Contacts screen.
Text here indicates
the active program.
Icons here indicate the
status of various system
functions.
Preliminary Draft 6/19/13, Not for Release
After the Dolphin terminal initializes, the Home screen appears.
TitleBar
The Title bar, located at the top of the screen, displays the active program, the status of various system
functions, and the current time. Touching on the title bar provides access to the Horizontal Scroll. The
scroll provides access to additional programs and application screens. For additional information, see
Horizontal Scroll on page 2-7.
Icons in the Title Bar
IndicatorMeaning
Synchronizing data
2 - 4
Icons in the Title Bar
Preliminary Draft 6/19/13, Not for Release
IndicatorMeaning
The terminal could not synchronize data with the workstation via ActiveSync.
New e-mail
New text message
New voicemail
New instant message
Vibrate on
Ringer off
Speaker phone on
Voice call in progress
Calls are forwarded
Call on hold
Missed call
Data call in progress
A battery error has occurred. Replace the main battery with a Honeywell Li-ion battery pack.
Battery is has a full charge
Battery has a high charge
Battery has a medium charge
Battery has a low charge
Battery has a very low charge and requires charging
Terminal is running on external power. If a battery pack is installed, the battery is charging in the
background.
The terminal is not connected to external power. A battery is installed, but is def ectiv e; specifically,
its charge level cannot be measured.
2 - 5
Icons in the Title Bar
Preliminary Draft 6/19/13, Not for Release
IndicatorMeaning
No SIM card is installed
Active network connection
No active network connection
GPRS available
GPRS connecting
GPRS in use
HSDPA available
HSDPA connecting
HSDPA in use
EDGE available
EDGE connecting
EDGE in use
UMTS available
UMTS connecting
UMTS in use
Radio is off
The radio is not connected to a network.
The radio is connected. The bars indicate the signal strength.
No radio signal
The terminal is searching for a signal.
Wi-Fi is on, but device is not connected
Wi-Fi data call
2 - 6
Icons in the Title Bar
The content of the
Horizontal scroll
changes according to
the open application.
The icons change according to the open application.
The Tile Bar displays icons you
use to open and close screens,
menus, and features.
Touch to access the
Start menu (page 2-9).
Touch the keyboard icon to toggle the Virtual Keyboard on or off.
Preliminary Draft 6/19/13, Not for Release
IndicatorMeaning
Pending alarm
Bluetooth
Horizontal Scroll
The Horizontal Scroll, located at the top of most application windows, provides access to additional
application screens. You can swipe left or right on the scroll or touch each label on the scroll, until you
get to the desired screen. Touching a label to the left or right of the center item brings new labels into
view.
Note: Touch the Title bar to access the horizontal scroll if it is not visible on the screen.
Tile Bar
The Tile Bar is located at the bottom of an application window.
Virtual Keyboard
The virtual keyboard appears when you open an application or select a field that requires text or
numerical input. You can also touch the keyboard icon on the tile bar to toggle the keyboard on or off.
When you touch an hold the keyboard icon, a pop-up menu allows you switch between the default
enhanced Honeywell virtual keyboard, which is fully customizable or the standard Windows Embedded
Handheld virtual keyboard.
2 - 7
The Enhanced Honeywell Virtual Keyboard
Preliminary Draft 6/19/13, Not for Release
During text input, you may need to switch between keyboard modes to access additional character sets
(e.g., function keys , symbols, and numbers). Each k eyboard mode , includes navigation k eys, which allo w
you to quickly switch between modes. Touch the ABC key to switch to the Qwerty Mode, the 123 key to
switch to the Numeric Mode, and the #@& key to switch to the Function & Symbols Mode.
Note: The content of the keyboard and the mode initially displayed may vary depending on the application in use
and the input field requirements.
Alternate Keys
Some keys include a second symbol in red. In order to use the alternate symbol, press and hold the key
until the alternate symbol appears, then release the key to type the symbol.
Honeywell Virtual Keypad Creator
The default enhanced virtual keyboard is fully customizable using the
software available for download at www.honeywellaidc.com. The user-friendly utility allows you to
personalize multiple keyboard features including key position, size, quantity, color, and the keyboard
skin. In addition, you can make language changes, create alternate or function ke ys f or special character
sets, and add application launch keys to streamline common business tasks.
Virtual Keypad consists of two software applications. The first is the
resides on your PC and is used to design and save keypad layouts. The second is the
which is downloaded to your mobile device. The
keypad you designed using
The customization process is easy. Simply download and install the
onto your PC, modify the provided standard template, then download the customized keyboard to your
terminal using a USB connection.
Virtual Keypad Creator
Virtual Keypad
.
Honeywell Virtual Keypad Creator
Virtual Keypad Creator
on your mobile device displays the
Virtual Keypad Creator
, which
Virtual Keypad
software
,
2 - 8
The Start Menu
Preliminary Draft 6/19/13, Not for Release
To see the programs loaded on your terminal, touch to access the Start menu.
Navigating the Start Menu
• Swipe up or down with your finger or stylus to scroll through the menu icons.
• To open a program, touch once on the program icon.
• To reposition an icon on the Start menu, touch and hold the stylus on the icon, then drag the icon to
the desired position.
Pop-Up Men us
With pop-up menus, you can quickly choose an action for a selected item. To access a pop-up menu,
touch and hold on the item name of the action you want to perform. When the menu appears, lift the
stylus, and touch the action you want to perform.
Touch anywhere outside the menu to close the menu without performing an action.
2 - 9
File Explorer
Touch to return to
the Start menu.
Touch to access
additional Menu
options.
Touch to move Up one
level in the directory.
T ouch to close
File Explorer.
Touch on the name to
open a file or folder.
Touch to toggle the virtual
keyboard display on or off.
T ouch and hold to access a
pop-up menu of keyboard
options.
Preliminary Draft 6/19/13, Not for Release
You can use the File Explorer to find files and organize files into folders.
Touch > File Explorer .
To move or copy files between folders using File Explorer:
1.Touch and hold on the item you want to move, then touch Cut or Copy on the popup menu.
2.Navigate to the folder you want to move or copy the file to, then touch and hold a blank area of the
window.
3.Touch Paste on the pop-up menu.
Note: If there is no blank space available in the window, touch
2 - 10
menu using the down arrow, then touch
Edit > Paste
.
Menu
on the tile bar, navigate to the end of the
File Provisioning on the Dolphin 60s
!
!
Preliminary Draft 6/19/13, Not for Release
\IPSM\Honeywell
The IPSM folder is the only partition on the terminal that persists across a kernel upgrade (*.UPG file
extension). During a kernel upgrade, files are automatically copied from the \IPSM\Honeywell folder
and then installed in the \Honeywell (root file system) folder as part of the upgrade process.
\IPSM\Honeywell\AutoInstall
The files in the IPSM\Honeywell\AutoInstall folder are only installed when a factory reset or
kernel upgrade occurs. Once the files are installed, they persist through hard and soft resets. If a file is
added to the folder and a hard or soft reset is performed, it will have no effect. If a program is manually
removed using the Remov e Progr ams application (see page 7-25), then the program is not automatically
re-installed on a hard or soft reset.
\Honeywell
The Honeywell partition or root file system partition is persistent over a hard reset, soft reset, and the
removal of the battery pack or the removal of AC power. However, during a kernelupgrade the root file
system is reformatted so all data in the folder is deleted and replaced by any files in the
\IPSM\Honeywell folder as part of the upgrade process.
To prevent data loss, back up all user data to an SD card or external memory device before performing an
upgrade.
\Honeywell\AutoInstall
If you run a CAB file from within the \Honeywell\AutoInstall (user store) folder, after the program
has been installed, the CAB file will be deleted from the User Store. However, the program remains
installed through all successive Hard and Soft resets.
If you want the program to be part of the Autoinstall that occurs after a f actory reset or software upgrade ,
paste the program file(s) in both the \IPSM\Honeywell\Autoinstall folder and the
\Honeywell\Autoinstall.
Contact a Honeywell technical support representative for information on how to perform a factory reset
or for information on available software upgrades for your Dolphin terminal. For contact information, see
Technical Assistance on page 14-1.
To prevent data loss, back up all user data to an SD card or external memory device before performing an
upgrade.
Search
The Search feature helps you quickly locate information. Touch > Search Phone .
Enter the text you want to find, select a data type, and then touch Search. Select Larger than 64 KB in
the Type drop-down field to quickly find information that is taking up storage space.
2 - 11
Suspend Mode
!
Preliminary Draft 6/19/13, Not for Release
In Suspend mode, the device enters a low power state to conserve battery power. The radio associated
with the phone maintains enough power to wake the terminal for incoming phone calls.
Suspend mode automatically turns the touch screen off to save battery power when the terminal is
inactive for a programmed period of time. The automatic timeout limits are adjustable from the
Advanced tab located under Settings > System > Power (see page 7-23).
To put the device into Suspend mode, press and release the Power key for approximately 4-5
seconds. To resume from the Suspend mode, press and release the Power key.
Replacing the Main Battery
Note: Before replacing the main battery, read the Guidelines for Battery Pack Use and Disposal on page 3-14.
Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating wet
components may cause damage not covered by the warranty.
1.Remove the battery door, slide the latch to unlock the battery door, remove the battery door, then
remove the battery.
2.Insert the new battery, then attach and lock the battery door.
Note: Do not attempt to use the terminal without the battery door installed.
3.The terminal begins booting as soon as power is applied.
2 - 12
We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in
!
Preliminary Draft 6/19/13, Not for Release
damage not covered by the warranty.
Resetting the Terminal
There are three types of system resets: a Soft Reset, a Hard Reset, or a Factory Reset. The soft and
hard resets preserve all data stored in the file system. Contact a Honeywell technical support representative for more information on how to perform a Factory Reset. For contact information, see Technical
Assistance on page 14-1.
Soft Reset (Warm Boot)
A Soft Reset re-boots the device and preserves any objects created in RAM. You would perform a soft
reset when: the terminal fails to respond, after installing some software applications, or after making
changes to certain system settings, such as network cards.
To perform a Soft Reset:
1.Press and hold the Blue key and then Power key for approximately 6-7 seconds.
2.When the reset is complete, the Home screen displays.
Hard Reset (Cold Boot)
A Hard Reset re-boots the terminal and closes any open applications running in RAM at the time of the
reset.
To perform a Hard Reset:
1.Press and hold the Blue key and then Send key for approximately 6-7 seconds.
2.When the reset is complete, the Home screen displays.
2 - 13
2 - 14
Preliminary Draft 6/19/13, Not for Release
3
Preliminary Draft 6/19/13, Not for Release
Hardware Overview
Standard Configurations for the Dolphin 60s
WLAN, WPAN & Camera
• Microsoft Windows Embedded Handheld
6.5 Professional
• TI AM3715 Cortex-A8 800MHz Processor
• 256MB RAM X 512MB Flash
• 3.7V Li-ion rechargeable extended battery
pack
• Dedicated imager capable of decoding
standard 1D and 2D bar code symbologies
• 5.0 megapixel auto focus camera
• 802.11b/g/n and Bluetooth
WLAN, WPAN, WWAN, GPS & Camera
• Microsoft Windows Embedded Handheld
6.5 Professional
• TI AM3715 Cortex-A8 800MHz Processor
• 256MB RAM X 512MB Flash
• 3.7V Li-ion rechargeable extended battery
pack
• Dedicated imager capable of decoding
standard 1D and 2D bar code symbologies
• 5.0 megapixel auto focus camera
• 802.11b/g/n and Bluetooth,
• Voice and Data, GSM/CDMA/GPS (US
bands) - SW Definable Radio
WLAN, WPAN, WWAN, GPS & Camera
• Microsoft Windows Embedded Handheld
6.5 Professional
• TI AM3715 Cortex-A8 800MHz Processor
• 256MB RAM X 512MB Flash
• 3.7V Li-ion rechargeable extended battery
pack
• Dedicated imager capable of decoding
standard 1D and 2D bar code symbologies
• 5.0 megapixel auto focus camera
• 802.11b/g/n and Bluetooth
• Voice and Data GSM/GPS (EU Bands)
WLAN, WPAN, WWAN, NFC, GPS & Camera
• Microsoft Windows Embedded Handheld
6.5 Professional
• TI AM3715 Cortex-A8 800MHz Processor
• 256MB RAM X 512MB Flash
• 3.7V Li-ion rechargeable extended battery
pack
• Dedicated imager capable of decoding
standard 1D and 2D bar code symbologies
• 5.0 megapixel auto focus camera
• 802.11b/g/n and Bluetooth
• Voice and Data, GSM/CDMA/GPS (US
bands) - SW Definable Radio
•NFC
WLAN, WPAN, WWAN, NFC, GPS & Camera
• Microsoft Windows Embedded Handheld
6.5 Professional
• TI AM3715 Cortex-A8 800MHz Processor
• 256MB RAM X 512MB Flash
• 3.7V Li-ion rechargeable extended battery
pack
• Dedicated imager capable of decoding
standard 1D and 2D bar code symbologies
• 5.0 megapixel auto focus camera
• 802.11b/g/n, and Bluetooth
• Voice and Data, GSM/GPS (EU Bands)
•NFC
3 - 1
Peripherals for the Dolphin 60s
Preliminary Draft 6/19/13, Not for Release
Each of the following items is sold separately to enhance the capabilities of your Dolphin terminal.
Dolphin 60s HomeBase Device (Model D60s-HB)
The Dolphin 60s HomeBase device is a charging and communication cradle equipped with a USB host
port that is Hi-Speed 2.0v compliant, which enables the terminal to interface with the majority of PCbased enterprise systems. This device also contains an auxiliary battery well that charges a spare
Honeywell extended battery pack.
For more information, see Dolphin 60s HomeBase Device (Model D60s-HB) on page 12-1.
Dolphin 60s Mobile Base Device (Model 60s-MB)
The Dolphin 60s Mobile Base is a charging cradle designed specifically for in-premise and in-transit data
collection applications. It features a fle xib le mounting brack et, an integr ated speaker with v olume control,
and a cigarette lighter adapter to adapt it to your mobile environment.
For more information, see Dolphin 60s Mobile Base Device (Model 60s-MB) on page 13-1.
3 - 2
Accessories for the Dolphin 60s
Preliminary Draft 6/19/13, Not for Release
Each of the following items is sold separately to enhance your terminal’s capabilities.
Note: When using accessories where the terminal is worn on the body, the terminal’s touch panel must face away
from the body.
Dolphin 60s Mobile Charger (Model 60s-MC)
The Dolphin 60s Mobile Charger is a charging cable that connects the terminal directly to a 12 Volt DC
power source, such as a cigarette lighter port inside a vehicle, eliminating the need for a cradle. Intelligent battery technology on-board the terminal ensures proper charging. The Dolphin 60s Mobile
Charger is an ideal low-cost charging solution for in-transit mobile applications.
USB Charge/Communication Cable and Adapter Kit (Model 60s-USB ADAPTERKIT)
The Dolphin USB charge/communication cable adapter kit is an all-in-one solution for charging and
communication. Use the 60s-USB cable in conjunction with provided power supply adapter and plug
adapter to charge the terminal from a power outlet or connect the cable to a high-power USB port to
charge from a host device. The 60s-USB cable also supports communication with a computer without
the need for a cradle. See Connecting and Synchronizing the Terminal and Workstation on page 8-9.
Holster (Model HOLSTER-1)
The holster provides conv enient storage for the Dolphin 60s terminal in mobile environments. The
holster features an integrated belt clip and spare battery pouch.
Battery
The rechargeable battery provides the main power f or the terminal. For more inf ormation, see Battery on
page 3-10.
3 - 3
Features of the Dolphin 60s
Power/End Call Key
Touch Panel Display
Scan Button
Charge
General Notification LED
Charge Indicator LED
Send Button
Microphone
Blue Modifier Key
Red Modifier Key
I/O Connector
(see page 3-10)
Right Scan/Image
Button
Navigation Keys
Audio Jack
Preliminary Draft 6/19/13, Not for Release
Note: Your Dolphin model may differ from the model illustrated; however, the features noted are standard for all
Dolphin 60s models with a Windows Embedded Handheld OS unless otherwise indicated. For a complete
overview of the optional keyboards available for the Dolphin 60s, .
Front Panel
For a description of each callout, see page 3-5.
3 - 4
Feature Descriptions: Front Panel
Preliminary Draft 6/19/13, Not for Release
Audio Jack
The 3.5mm audio jack supports both speaker (stereo) and microphone (mono) headsets.
Blue Modifier Key
See Using the Modifier Keys on page 6-3.
Power/End Call Key
The Power/End Call key, located in the upper right corner of the keypad, puts the terminal in
Suspend Mode or wakes the terminal from Suspend Mode. See Suspend Mode on page 2-11.
The key is also used to end/disconnect a phone calls.
Charge Indicator LED
The light emitting diode (LED) located above the top left corner of the LCD display illuminates
when the Power Tools BattMon application is enabled and the device is on AC charge. For
more information, consult the Dolphin Power Tools User’s Guide for Windows Embedded
Handheld 6.5.
Front Speaker
The front speaker is the receiver for handset voice calls. See Voice Communication on page
9-4.
General Notification LED
The light emitting diode (LED) located above and to the right of the LCD display flashes and
illuminates during resets, scanning/imaging, and taking a picture. The LED indicates that an
external power source is connected to the terminal. This LED can be programmed by various
software applications.
Microphone
The integrated microphone that provides audio input for handset and speaker phone voice
calls. See Voice Communication, Using the Dolphin as a Phone on page 9-3.
Navigation Keys
The centrally located navigation keys enable you to move and position the cursor through
software programs. The up and down arrows are programmed to perform specific functions
when pressed in combination with the Blue and Red modifier keys. For more details, see Using
the Navigation Keys on page 6-3.
Red Modifier Key
See Using the Modifier Keys on page 6-3.
Right Scan/Image Button
By default, the right button triggers the scanner/imager. You can reassign the button to launch
applications or execute commands. For additional information, see Changing Button
Assignments on page 7-5.
Scan Button
The Scan button is centrally located for easy access with the right or left hand. By default, the
button activates the scanner/imager.
3 - 5
Send Button
Preliminary Draft 6/19/13, Not for Release
Answers a phone call or initiates a phone call. See Voice Communication on page 9-4.
Touch Panel Display
The color 2.8 inch (liquid crystal display (LCD) touch panel is covered with an industrial,
protective lens for greater durability. The quarter video graphic array (QVGA) display
resolution is 240 X 320. The touch panel can be activated with a finger or with the stylus.
The touch panel backlight illuminates when the screen is touched. For more information, see
Backlight on page 7-12.
3 - 6
Back Panel
Image Engine Window (LED Aimer Aperture)
Fastener for the
Stylus Tether
Battery Lock
Battery Lock (battery and
battery door not shown)
SIM Card Socket
Back Speaker
Volume Control
Button
Battery Door
Memory Card Socket
USB Door/Micro USB Port
Lanyard Slot
Stylus/Stylus
Slot
Preliminary Draft 6/19/13, Not for Release
Note: Your Dolphin model may differ from the model illustrated; however, the features noted are standard for all
Dolphin 60s with Windows Embedded Handheld models unless otherwise indicated.
For a description of each callout, see Feature Descriptions: Back Panel on page 3-8.
3 - 7
Feature Descriptions: Back Panel
Preliminary Draft 6/19/13, Not for Release
Back Speaker
The integrated rear speaker sounds audio signals as you scan bar code labels and enter data.
The integrated speaker also supports playback of wave and MP3 files, software mixer, and
Speakerphone for WWAN/GSM audio. The operating frequency range is 600-3000Hz at
>90dB.
Battery
Dolphin 60s model terminals are designed for use with battery part number
BAT-EXTENDED-01 (Li-ion 3.7 V, 12.358 watt hour) manufactured for Honeywell International
Inc. For information on how to remove the battery, see Replacing the Main Battery on page 2-
12.
Battery Door
The battery door protects the battery and any installed SIM and/or memory cards in the
terminal’s battery well. When the battery door is installed properly, the terminal’s
environmental rating is preserved. For information on how to remove the battery, see
Replacing the Main Battery on page 2-12.
Note:Do not use the terminal without the battery door installed.
Battery Lock
The Battery Lock allows the user to lock the battery door in place.
Color Camera
The 5.0-Megapixel Resolution auto-focus color camera provides easy picture and video
capture. The camera lens and camera flash are located on the back panel of the terminal.
Fastener for the Stylus Tether
The Stylus Tether helps prevent accidental loss when the stylus is not stored in the stylus slot.
A stylus tether is a coiled, elastic cord that tethers the stylus to the terminal. Secure one end
of the cord to the back panel of the terminal and the other end to the stylus.
Flashlight/Camera Flash
The flashlight/camera flash is located on the back panel of the terminal.
When used as a Flashlight, touch
turn the flashlight On or Off.
When used as a Camera Flash with the terminal’s color camera, the flash is controlled by the
camera application.
Image Engine Window
The image engine reads and decodes linear, stacked linear (e.g., PDF417), and 2D matrix bar
code symbologies. The LED aperture for the imaging engine’s LED aimer is contained behind
this window. For more details, see Using the Scan Image Engine on page 4-1.
> Flashlight or press the Red Key > ,to
3 - 8
Memory Card Socket
Preliminary Draft 6/19/13, Not for Release
The memory card socket provides the user with the option to expand the terminal’s memory
capacity using microSD or microSDHC memory interfaces. The expansion socket is located
under the battery door and battery.
Note:Honeywell recommends the use of Single Level Cell (SLC) industrial grade microSD or
When the battery door and battery pack are properly installed, the card is sealed against
moisture and particle intrusion, read/write data is stored securely, and the terminal’s
environmental rating is preserved; see Installing a SIM Card and/or Memory Card on page 3-
16.
SIM Card Socket
The card socket for the Subscriber Identity Module (SIM) is located under the battery door and
main battery. When the battery door and battery are properly installed, the card is sealed
against moisture and particle intrusion, read/write data is stored securely, and the terminal’s
environmental rating is preserved; see Installing a SIM Card and/or Memory Card on page 3-
16.
Stylus/Stylus Slot
The stylus is used to operate the touch panel. The back panel of the terminal features a storage
slot to hold the stylus when not in use. The stylus features a special tip for added accuracy and
ease of use.
USB Door/Micro USB Port
The Micro USB port is located under the protective USB door on the right side of the terminal.
To access the micro USB port, gently lift the top edge of the door closest to the digital
microphone, and then twist 90° counterclockwise.
microSDHCmemory cards with Dolphin terminals for maximum performance and durability.
Contact a Honeywell sales representative for additional information on qualified memory card
options.
The micro USB port in conjunction with the USB Charge/Communication Cable (model 70eUSB) powers the terminal, charges the main battery, and facilitates communication. The micro
USB port supports low, full, and high-speed USB v2.0 client communication with a maximum
rate of 480 Mbps.
For additional information, see Using the USB Charge/Communication Cable (Model 60s-USB
ADAPTERKIT) on page 2-2 and Connecting and Synchronizing the Terminal and Workstation
on page 8-9.
Volume Control Button
Press the top or bottom of the volume button to raise or lower the volume of the active speaker.
3 - 9
The I/O Connector
Pin 1
Pin 9
Terminal Back Panel
!
Preliminary Draft 6/19/13, Not for Release
The I/O connector powers the terminal, charges the main battery , and f acilitates communication. Dolphin
60s peripherals are designed to work exclusively with this connector. The I/O connector supports low,
full, and high speed USB v2.0 communication with a maximum rate of 480 Mbps.
PinSignalDescription
1VDC_IN5V DC input for charging and operation
2VBUS_HOST5V output for USB host and peripheral
3USB_DM_HOSTUSB D- for the host port
4USB_DP_HOSTUSB D+ for the host port
5USBC_DETMultipurpose pin to allow for detection of an
6GNDGround connection
7USB_DN_DOCKUSB D- for the client port
8USB_DP_DOCKUSB D+ for the client port
9VBUS_DOCK5V input for USB client (and charging)
Note: Signals referenced are for a DTE device.
power
unpowered SLED, determine SLED type,
and to signal a HomeBase the docking of
the terminal.
Battery
The primary power source for the Dolphin terminal is the 3.7V Li-ion rechargeable battery located under
the battery door on the back panel of the device. Honeywell recommends, you keep the battery in the
terminal charged at all times to help prevent data loss. Letting the battery become fully discharged
causes the terminal to lose all data in RAM.
Note: All data in RAM is cleared when the battery is removed. Always Power Off the terminal before removing the
battery to ensure any changes made are saved to the flash memory.
Dolphin 60s model terminals are designed for use with battery part number BAT-EXTENDED-01 (Li-ion
3.7 V, 12.358 watt hour) manufactured for Honeywell International Inc.
We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in
damage not covered by the warranty.
Charging Options
Dolphin terminals ship with the battery significantly discharged of power. The battery must be
completely charged for a minimum of 6 hours before using a Dolphin terminal for the first time.
3 - 10
When the main battery is installed in the terminal, use one of the following:
Preliminary Draft 6/19/13, Not for Release
• Dolphin 60s HomeBase Device (Model D60s-HB), see page 12-1
• Dolphin 60s Mobile Base Device (Model 60s-MB), see page 13-1
• Dolphin 60s USB Charge/Communication Cable (Model 60s-USB ADATPERKIT), see page 2-2
When the main battery is not installed in the terminal:
• Place the battery pack in the Auxiliary Battery Well of the Dolphin 60s HomeBase Device (Model D60s-
HB).
For inf ormation on how to remov e the battery from the terminal, see Replacing the Main Battery on page
2-12.
Charging Time
The extended battery pack requires 6 hours to charge completely.
Note: Using the terminal while charging the battery significantly increases the time required to reach a full charge.
Important Charging Guidelines
Source Current Specifications
Battery charging times can be significantly lengthened or charging may not occur if the terminal is
drawing more currant than is supplied by the charging peripheral (e.g., HomeBase), USB wall charger , or
USB Host (e.g., workstation PC).
• The maximum current supplied through a charging peripheral is 2.0A.
• The maximum current supplied by the USB wall charger is 900 mA.
• The maximum current supplied by a USB Host can vary from 100mA to 500mA.
Do not attempt to charge the terminal from a 100 mA source. An active Dolphin terminal uses more
current than supplied by a 100 mA source causing the terminal to continue to draw power from the
battery.
Note: Placing the terminal in Suspend mode while charging reduces the current draw of the terminal and shortens
the charging time of the battery.
To verify your terminal is not drawing more current then supplied by the charging source:
1.Touch > Settings > System > Batterywhen the terminal is connected to a
charging source.
2.Check the Battery Current. If the current is positive, then charging current is going into the battery. If
the current is negative, the battery is discharging current and your terminal is drawing more current
than the charging source.
Note: The charging current is always less than source current due to the terminal being in operation.
3 - 11
Charging a Severely Low or Completely Discharged Battery
Preliminary Draft 6/19/13, Not for Release
Battery Charge StatusSymptom
Severely LowPressing the Power button does not wake the terminal from Suspend mode. The general
notification LED may flash once when the Power button is pressed.
Completely DischargedPressing the Power button does not wake the device and the general notification LED
remains off.
Use one of the following options to charge a severely low or completely discharged battery.
1.Insert the battery into the auxiliary battery well of the HomeBase. When the auxiliary battery LED on
the HomeBase turns green, the battery is fully charged.
2.Dock the terminal into the charging well of a peripheral (e.g., HomeBase). The terminal starts to boot
as soon as power is supplied by the base.
Note: To prevent the possible loss of unsaved data, do not remove the terminal from the base until the battery
has sufficiently charged. Touch the Start > Settings > System > Battery to view detailed information
on the status of the battery.
3.Charge the terminal from a wall power outlet using the USB Charge/Communication Cable and
power supply provided with your terminal. As the battery charges, the charge indicator LED will be
red. When the battery reaches a safe charge threshold and the terminal begins to boot. The length
of time before the battery reaches a safe charge threshold varies depending on the extent of the
battery discharge.
4.Charge the terminal from a USB host device (PC) using the USB Charge/Communication Cable.
Note: Inadequate source current may interfere with effective battery charging; see Important Charging
Guidelines on page 3-11 for additional information.
As the battery charges, the charge indicator LED will be red. When the battery reaches a safe
charge threshold and the terminal begins to boot. The length of time before the battery reaches a
safe charge threshold varies depending on the extent of the initial battery discharge level and the
current supplied by the USB charging source.
Battery Error Notification
If your terminal displays the following indicators, replace the battery with a Honeywell Dolphin 60s
extended battery pack. For information on how to remove the battery from the terminal, see Replacing
the Main Battery on page 2-12.
• An “Authentication Error” pop up window appears during startup.
• appears in the Title bar at the top of the touch screen.
• The General Notification LED illuminates red.
• A Notification appears on the Tile bar at the bottom of the touch screen.
Storing Batteries
To maintain top performance from batteries, avoid storing batteries outside of the following temperature
ranges:
• 14°F to 113°F (-10°C to +45°C) for short term storage of less than one month
• 32°F to 86°F (-0°C to +30°C) for long term storage
3 - 12
Do not store batteries in extremely high humidity. For prolonged storage, do not keep batteries stored in
Preliminary Draft 6/19/13, Not for Release
a charger that is connected to a power source.
3 - 13
Guidelines for Battery Pack Use and Disposal
Preliminary Draft 6/19/13, Not for Release
The following are general guidelines for the safe use and disposal of batteries:
• Do not disassemble or open crush, bend or deform, puncture or shred.
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or
expose to water or other liquids, expose to fire, explosion or other hazard.
• Improper battery use may result in a fire, explosion or other hazard.
• We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may
pose a personal hazard to the user.
• Only use the battery for the system for which it is specified. Do not use a battery in any other
manner outside its intended use in Dolphin terminals and peripherals.
• Only use the battery with a charging system that has been qualified with the system per CTIA
Certification Requirements for Battery System Compliance to IEEE 1725. Use of an unqualified
battery or charger may present a risk of fire, explosion, leakage, or other hazard.
• Replace the battery only with another battery that has been qualified with the system per this
standard, IEEE-Std-1725. Use of an unqualified battery may present a risk of fire, explosion,
leakage or other hazard.
• Replace defective batteries immediately; using a defective battery could damage the Dolphin
terminal.
• Never throw a used battery in the trash. Promptly dispose of used batteries in accordance with
local regulations.
• Do not short-circuit a battery or throw it into a fire; it can explode and cause severe personal
injury. Do not allow metallic conductive objects to contact battery terminals.
• If you observe that the Honeywell battery supplied is physically damaged, please send it to
Honeywell International Inc. or an authorized service center for inspection, see Product Service
and Repair on page 14-1.
• Battery usage by children should be supervised.
• Avoid dropping the terminal or battery. If the terminal or battery is dropped, especially on a hard
surface, and the user suspects damage, send it to a Honeywell International Inc. or an authorized
service center for inspection.
• If you are not sure the battery or charger is working properly, send it to Honeywell International
Inc. or an authorized service center for inspection, see Product Service and Repair on page 14-1.
• Excessive discharge can degrade battery performance. Recharge the battery when your terminal
indicates low battery power.
• Although your battery can be recharged many times, the battery life is limited. Replace it after the
battery is unable to hold an adequate charge.
• The Dolphin 60s should only be connected via its microUSB connector to CTIA certified
adapters, products that bear the USB-IF logo or products that have completed, the USB-IF
compliance program.
Managing Battery Power
Letting the battery become fully discharged causes the terminal to lose all data in RAM. Honeywell
recommends, you keep a charged battery in the terminal at all times to help prev ent data loss. Removing
the battery from the terminal erases all non-persistent memory.
Default Critical and Low Battery Points
When the terminal is running on battery power (as opposed to external power), warnings are displayed
when the battery reaches critical and low battery points. The warning points are determined by the
following registry entry:
[HKEY_LOCAL_MACHINE\ControlPanel\Power]
3 - 14
There are two DWORD values in this registry entry: MedState and LowState.
Preliminary Draft 6/19/13, Not for Release
The default values for these entries are as follows:
MedState=25%
This sets the Low Battery point to 25%. When the battery hits the percentage charge specified
here, the user is notified.
LowState=10%
This sets the Critical Battery point to 10%. When the battery hits the percentage charge
specified here, the user is notified.
Note: Warnings do not appear when the terminal is on external power.
Setting Critical and Low Battery Points
Developers can reset the battery parameters in the registry from 0 (no warning) to 99 (would nearly
always warn). You can review and set these battery points in the RegEdit Power Tool.
1.Touch > Power Tools > RegEdit.
2.Drill down to HKEY_LOCAL_MACHINE > ControlPanel > Power.
3.Touch the Value Name (i.e., MedState or LowState) to change the Value Data.
You can reset the Value Data from 0 (no warning) to 99 (would nearly always warn).
4.Touch OK to save changes.
Checking Battery Power
1.Touch > Settings > System
2.Touch Powerto view the power status of the main battery.
Or
Touch Battery
For additional information on Advanced Power Settings, see page 7-25.
For additional information on the Battery Log Configuration, see page 7-14.
to view detailed information on the installed battery pack.
System Resets
See Resetting the Terminal on page 2-13.
3 - 15
Hardware Maintenance
SIM Card Latch
Preliminary Draft 6/19/13, Not for Release
When needed, clean the image engine window and the touch screen with a clean, non-abrasive , lint-free
cloth. The terminal can be cleaned with a damp cloth.
Important - All battery and connector doors must be present, undamaged, and properly closed on the
terminal to maintain an IP54 rating.
Installing a SIM Card and/or Memory Card
SIM Card
Short for Subscriber Information Module, a SIM card stores the subscriber's personal information,
GSM/GPRS radio settings, security keys , contacts, etc. SIM cards can be installed in compatible mobile
devices, enabling you to switch devices without losing personal and setup information.
Before installing the SIM card, the service provider must activate the SIM card.
Note: If no SIM card is installed, you can still make emergency phone calls (e.g., 9-1-1).
Installation
1.Suspend the terminal. Press and release the Power key for approximately 4-5 seconds.
2.Unlock and remove the battery door, then remove the battery.
3.Slide the SIM Card latch toward the bottom of the terminal to unlock.
4.Lift the SIM card latch.
3 - 16
5.Slide the SIM (contacts facing down) into the socket, then close the SIM card latch.
Chamfered Corner
of SIM Card
Preliminary Draft 6/19/13, Not for Release
6.Lock the SIM card latch by sliding the latch toward the top of the terminal.
7.Install the battery, then attach and lock the battery door The terminal begins booting as soon as
power is applied.
Memory Card
You can expand the terminal’s memory capacity by installing a microSD or microSDHC memory card.
Honeywell recommends the use of Single Level Cell (SLC) industrial grade microSD or microSDHC
memory cards with Dolphin terminals for maximum performance and durability. Contact a Honeywell
sales representative for additional information on qualified memory card options.
Note: Format the memory card before initial use.
Installation
1.Suspend the terminal. Press and release the Power key for approximately 4-5 seconds.
2.Unlock and remove the battery door, then remove the battery.
3 - 17
3.Slide the SIM Card latch toward the bottom of the terminal to unlock, then lift the SIM card latch. If a
SIM Card Latch
Preliminary Draft 6/19/13, Not for Release
SIM card is installed, remove the SIM card to reveal the memory card latch.
4.Slide the memory card latch to the left to unlock, then lift the memory card latch.
5.Insert a MicroSD or MicroSDHC card into the socket aligning the corner on the card with the corner
6.Close the memory card latch, then lock by sliding the latch right. If you want to install a SIM card,
of the socket.
insert the card into the SIM card socket (see SIM Card).
3 - 18
7.Close the SIM card latch, then lock the SIM card latch by sliding the latch toward the top of the
Preliminary Draft 6/19/13, Not for Release
terminal.
8.Install the battery, then attach and lock the battery door The terminal begins booting as soon as
power is applied.
3 - 19
3 - 20
Preliminary Draft 6/19/13, Not for Release
4
Preliminary Draft 6/19/13, Not for Release
Using the Scan Image Engine
Overview
The Dolphin 60s terminal houses a compact image engine that instantly reads popular 1D and 2D bar
codes and supports omni-directional aiming and decoding for greater flexibility in real-world settings. The
image engine can also capture black and white digital images, such as signatures and pictures of
damaged inventory.
With the latest CMOS-based technology, the engine works like a digital camera and enables black and
white digital image capture, signature capture, and reading of OCR characters.
LED Safety
See LED Safety on page 1-1.
Image Engine Specifications
Field of View
Horizontal Field Angle (°) 21.9+/-0.5 degree
Vertical Field Angle (°) 15.9+/-0.5 degree
Depth of Field
The depth of field measurements used the following parameters:
• Distances are measured from the front of the engine.
• +23°C (+73°F), 0 lux
• Photographic quality codes
SymbologyDistance (in/cm)
Near
3 mil C39/128--5 mil C39/1282.25 (5.7)4.35 (11.049)2.1 (5.3)
7.5 mil C39/1281.25 (3.2)6.87 (17.4)5.62 (14.3)
10 mil C39/1280.67 (1.7)9.93 (25.2)9.26 (23.5)
15 mil C39/1281.01 (2.6)15.16 (38.5)14.15 (35.94)
20 mil C39/1281.80 (4.57)18.56 (47.14)16.76 (42.57)
Distance (in/cm)
Far
Delta (in/cm)
100% 13 mil UPC1.57 (3.9)12.18 (30.9)10.61 (26.9)
5 mil PDF417---
6.7 mil PDF4171.53 (3.8)4.63 (11.7)3.1 (7.8)
10 mil PDF4171.38 (3.5)7.34 (18.6)5.96 (15.1)
4 - 1
5 mil microPDF---
Preliminary Draft 6/19/13, Not for Release
5 mil DataMatrix--10 mil DataMatrix1.52 (3.8)4.87 (12.3)3.35 (8.5)
20 mil DataMatrix1.07 (2.7)9.66 (24.5)8.59 (21.8)
10 mil QR1.50 (3.8)5.13 (13.0)3.63 (9.2)
20 mil QR2.48 (6.3)9.66 (24.5)7.18 (18.2)
32 mil Maxicode1.56 (3.9)13.19 (33.5)11.63 (29.5)
Supported Bar Code Symbologies
Symbology TypeSymbology Name
1D SymbologiesCodabar
Codablock F
Code 3 of 9
Code 11
Code 32 Pharmaceutical (PARAF)
Code 93
Code 128
EAN with Add-On
EAN with Extended Coupon Code
EAN-8
EAN-13
GS1-128
GS1 Databar
Interleaved 2 or 5
2D Symbologies Aztec
Codablock A
Codablock F
Data Matrix
Composite Codes UPC/EAN
UCC/EAN
GS1 Databar
OCR MICR E 13-B
OCR-A
OCR-B
ISBT 128
Matrix 2 of 5
MSI Plessey
Straight 2 of 5 IATA
Straight 2 of 5 Industrial
Telepen
Trioptic Code
UPC with Add On
UPC-A
UPC-E
GS1 Databar
MaxiCode
Micro PDF
PDF417
QR Code
Postal Codes Postnet and most international 4-state codes
Australian Post
British Post
4 - 2
Canadian Post
China Post
Decoding
Preliminary Draft 6/19/13, Not for Release
The terminal supports two types of image decoding for use in various bar code reading and imaging
applications: full-area imaging and Advanced Linear Decoding (ALD).
Full-Area Imaging
Full-area imaging provides omni-directional reading of linear and non-linear 1D and 2D bar codes, OCR,
signature capture, and picture taking. When reading all bar code types using full-area imaging, a positive
read can be obtained from many positions; see The Aiming Beam on page 4-3. To achiev e the best read,
the aiming beam should be centered horizontally across the bar code.
ALD
ALD provides fast reading of linear and stacked linear bar codes. To achieve a positive read when
reading linear 1D and PDF417 bar codes, the aiming beam should be centered horizontally across the
bar code. When ALD is enabled, the reader does not read matrix or postal codes.
Using the Scan Demo to Decode a Bar Code
The aiming beam should be oriented in line with the bar code to achieve optimal decoding.
1.Touch > Demos > Scan Demo .
2.Point the Dolphin terminal at the bar code. Press and hold the Scan button.
Note: The right side buttons also trigger the scan/imager.
.
3.Center the aiming beam over the bar code; see The Aiming Beam on page 4-3.
Note: By default, the LED illumination and aiming beam options are enabled. For optimum performance, avoid
reflections by scanning the bar code at a slight angle.
4.When the bar code is successfully decoded, the terminal beeps and the bar code information
appears on the touch screen.
The Aiming Beam
The aiming beam is smaller when the terminal is held closer to the code and larger when it is farther
from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit
whereas symbologies with larger bars or elements (mil size) should be read farther from the unit.
4 - 3
Linear Bar Code
Preliminary Draft 6/19/13, Not for Release
2D Matrix Symbol
Capturing Images Using the Imaging Demo
The image-capture process is an intuitive, split-second operation f o r e xperienced users. By f ollo wing the
basic guidelines, new users can easily develop their own technique and, with practice, quickly learn to
adapt it to different application environments.
Image Preview
When the imaging process is initiated, the touch screen displays a preview of the object. This is a live
video image of what the imager is currently viewing. The live video image has a slightly degraded
appearance compared to the captured image. This is normal.
Scan Key
On all Dolphin 60s terminals, the Scan button captures images.
File Formats
File formats supported for image storage include Bitmap (BMP), JPEG (JPG) and Portable Network
Graphics (PNG). The default file format for images is a gray scale JPG.
Compression
Digital images have a maximum image size of 640 x 480 pixels and may have up to a 256 (8 bit) gray
scale image definition.
The image quality and related file size are determined by the data compression method used by the
software application used to take images. The average size of the image file is approximately 4–8K.
Howev er, the size of the image depends on the content of the image - the more comple x the content, the
larger the file size.
Taking an Image
The following steps are basic guidelines for taking images:
4 - 4
1.Touch > Demos > Imaging Demo .
Preliminary Draft 6/19/13, Not for Release
2.Point the Dolphin terminal at the object. To preview the image, press and hold the Scan button.
Note: The general notification LED above the touch screen illuminates red while the Scan button is pressed.
3.Adjust the terminal’s position until the object appears on the touch screen the way you want it to
appear in the image.
4.Release the Scan button to capture the image.
5.Touch File on the Tile bar, then select Save or Save As.
Note: Unless otherwise specified, the image is saved to the \My Device\My Documents folder.
Enabling the Aimer
By default, the Aiming Beam (see page 4-3) is turned off in the Imaging Demo application. To enable the
aiming beam for image capture:
1.Touch File at the bottom of the Imaging Demo screen.
2.Select S
Note: If an option is enabled, a check mark appears next to the name.
3.The aiming beam is now enabled for imaging.
etup from the menu, then touch Aimer.
Uploading Images
Image files can be uploaded to a host workstation using Microsoft ActiveSync or Windows Mobile De vice
Center and a Dolphin communication peripheral. For additional information see Connecting and
Synchronizing the Terminal and Workstation on page 8-9.
4 - 5
4 - 6
Preliminary Draft 6/19/13, Not for Release
5
Color
SaturationContrastLamp
BrightnessPixels
Sharpness
Zoom
Flashlight/
Camera Flash
Camera Lens
Preliminary Draft 6/19/13, Not for Release
Using the Color Camera
Overview
Dolphin 60s terminals are equipped with 5.0-Megapixel auto focus cameras to provide easy integration
of color picture and video capture into business applications. The camera lens and camera flash are
located on the back panel of the terminal.
Taking a picture using the Camera Demo tool
1.Touch > Demos > Camera Demo.
2.Adjust the camera settings using the icon menu at the top of the display screen.
3.Point the terminal's camera lens at the object you want to capture.
4.Center the object you want to take a picture of on the live preview screen.
5.Press the ENT key or Touch
Note: Touch the green arrow to review or edit your pictures.
To exit the picture review/edit screen, touch the green box .
on the touch screen.
5 - 1
Camera Options
Profile Tab
The profile tab allows you to
customize your camera
settings, or chose from sev eral
predefined profiles designed to
provide the best picture quality
for common tasks.
Display Tab
Preliminary Draft 6/19/13, Not for Release
The Camera Options menu provides access to create customized profiles, adjust audible feedback,
modify file preferences, and set caption options. Touch Options > Camera to access the Camera
Options menu.
The Camera Options screen contains five tabs: Profile, Display, Capture, Caption, and File.
5 - 2
Capture TabCaption Tab
Capture Tab
Preliminary Draft 6/19/13, Not for Release
5 - 3
Taking a picture using the Windows Embedded Handheld 6.5 Camera tool
Preliminary Draft 6/19/13, Not for Release
1.Touch > Pictures & Videos > Camera
2.Point the terminal's camera lens at the object you want to capture.
Note: The camera lens is located on the back panel of the terminal.
3.Center the object you want to take a picture of on the live preview screen. Adjust the camera
settings or let the camera auto-focus.
Note: Focus On is the default Focus mode. In this mode, the camera performs auto-focus while it is in preview
mode but not during picture capture.
4.Press the Scan button to capture the photo.
5.The touch screen displays the captured photo. Touch OK or Camera on the Tile Bar to return to the
active viewfinder screen.
Menu
Touch Menu on the Tile Bar at the bottom of the touch screen to adjust the camera settings, switch to
video mode, and access additional camera options.
ItemDescriptions
VideoActivate Video Mode
ModeSet Mode (i.e., Normal, Burst, or Timer)
ResolutionSet Picture Resolution (i.e., QVGA, VGA, SVGA, XGA, UXGA, QXGA, or MEGA5)
ZoomSet Zoom (i.e., x1, x2, or x3)
FlashSet Camera Flash On or Camera Flash Off
FocusSet Focus Off, Focus On (default), Focus on Trigger, or Fixed-Focus
Focus On (default setting):
The camera auto-focuses while it is in preview mode. As you move the camera, the lens
targets and auto-focuses on different objects. Once the picture is in focus in preview
screen, the camera is ready for the picture to be taken. To reduce the capture time of the
photo, the camera does not auto-focus during picture capture process.
Focus on Trigger:
The camera auto-focuses while it is in preview mode and again during picture capture.
The Focus on Trigger lengthens the capture time of the photo.
BrightnessSet the brightness setting from +2.0 EV to -2.0 EV in .5 EV increments
Full ScreenSwitch to full screen mode
OptionsSet Camera Options, Video Options, Slide Show Options or General Options
5 - 4
Options
General TabSlide Show Tab
Camera TabVideo Tab
Preliminary Draft 6/19/13, Not for Release
Touch Menu > Options. The Options menu contains four screens:
5 - 5
Recording Video using the Windows Embedded Handheld 6.5 Camera Tool
Preliminary Draft 6/19/13, Not for Release
1.Touch > Pictures & Videos > Camera > Menu > Video
2.Point the terminal's camera lens at the object you want to capture.
3.Press the Scan button to start recording.
4.Touch Stop on the screen or press Scan button to stop recording.
Uploading Pictures and Videos
Picture and Video files can be uploaded to a host workstation using Microsoft ActiveSync or Windows
Mobile Device Center and a Dolphin communication peripheral. For additional information see
Connecting and Synchronizing the Terminal and Workstation on page 8-9.
5 - 6
6
30-Key Numeric Keyboard46-Key QWERTY Keyboard
Red
Preliminary Draft 6/19/13, Not for Release
Using the Keyboards
Available Keyboards
Note: Contact a sales representative for information on additional keyboard options.
All Keyboards Contain the Following:
• Backlit for easy viewing in various lighting conditions.
• Centrally located Scan key for both right- and left-hand operation.
• Color-coding so you can clearly see the most common keyboard combinations.
• Function, navigation, and modifier keys.
Keyboard Combinations
See 30-Key Numeric Keyboard on page 6-4.
See 46-Key QWERTY Keyboard on page 6-6.
Common Buttons
See Using the Function Keys on page 6-1.
See Using the Modifier Keys on page 6-3.
See Using the Navigation Keys on page 6-3.
Using the Function Keys
NameKey SymbolFunction
BacklightTurns the keyboard backlight on or off.
Flashlight
&
Turns the flashlight on or off. The flashlight is located on the back panel of the
terminal.
6 - 1
NameKey SymbolFunction
Preliminary Draft 6/19/13, Not for Release
BackspaceMoves the cursor back one space each time the key is pressed. If you are
typing text, it deletes the previous character each time it is pressed.
EnterConfirms data entry.
Escape Cancels the current action.
Power/End
Call Key
SCAN Key Activates the scan and wakes the terminal from Suspend Mode.
Space
or
TabMoves the cursor to the next tab stop or the next control (on a form).
The Power key, located in the upper right corner of the keypad, puts the
terminal in Suspend Mode or wakes the terminal from Suspend Mode, see
Suspend Mode on page 2-12. This key is also used to end/disconnect a phone
calls.
The key location allows convenient one-handed image-taking and/or bar code
decoding.
Moves the cursor one space.
6 - 2
Using the Modifier Keys
Blue
Red
Preliminary Draft 6/19/13, Not for Release
NameKeyFunction
Blue & Red The blue and red keys are used in combination with other keys to type
special characters and perform system functions. Each keyboard is
color-coded to indicate the character typed or function performed when
specific keys are pressed immediately after the blue or red modifier key.
Normal
Press the blue or red key once to modify only the next key pressed.
Locked
Press the blue or red key twice to toggle the modifier lock on or off.
If a modifier key is lock ed on, the ne xt ke ys pressed are modified until the
lock is turned off. This prevents having to press the modifier key each
time a key is pressed.
Note: Press the locked modifier key once to temporarily unlock the
modifier key for a single key stroke.
ShiftThe shift key modifies only the next key pressed; it must be pressed
before each key you wish to modify. Shift toggles the keyboard between
uppercase alphabet mode and lowercase alphabet mode.
Press the shift key twice to toggle Caps Lock ON or OFF.
Using the Navigation Keys
Located in the center of each keyboard for easy access with either hand, the navigation keys navigate
the cursor through application screens.
KeyFunction
Moves the cursor up one row or line.
Moves the cursor down one row or line.
Moves the cursor one character to the right.
Moves the cursor one character to the left.
Note: Additional functionality varies according to the application in use.
6 - 3
30-Key Numeric Keyboard
Backlight /
Flashlight Key
SCAN Key
Enter Key
Tab Key
Escape Key
Power Key / END Key
Left Soft Key
Right Soft Key
Red Key
Blue Key
Down Navigation Key
Backspace Key
Space Key
Shift Key
Right Navigation Key
Left Navigation Key
SEND key
Up Navigation Key
Preliminary Draft 6/19/13, Not for Release
30-Key Numeric Keyboard Combinations
KeyNormalBlue + NormalBlue + Normal +
Shift
Left Soft KeyLeft Soft Key performs the left function.
SCANSCAN
Right Soft KeyRight Soft Key performs right function.
SENDSENDCold BootCold BootSEND
Left Navigation Left
Up NavigationUp
Down
Navigation
Right
Navigation
Down
Right
Red + Normal
6 - 4
KeyNormalBlue + NormalBlue + Normal +
Preliminary Draft 6/19/13, Not for Release
Shift
Red + Normal
Power/ENDPower On/Off or
END Call
TABTABback TABTABTAB
11@ ? !@ or ? or !F1
22ABCabcF2
33DEFdefF3
SpaceSpace
BacklightBacklightBacklightBacklightflashlight
44GHIghiF4
55JKLjklF5
66MNOmnoF6
Backspacebackspace
ESCEscape
Customized settings are av ailable on the System Settings menu. Touch > Settings and the
settings screen opens.
IconDescription
BluetoothConfigure the Bluetooth radio. See Working with the Bluetooth Radio on page 10-1.
HomeCustomize the look and the information displayed on the Home screen.
Clock &
Alarms
LockPassword protect the terminal to limit access. See Lock on page 7-3.
Sounds &
Notifications
Set the system clock, date, time and schedule alarms. See Clock & Alarms on page
7-2.
Set the sound volume, enable or disable sounds for specific actions, set sound
parameters for system notifications and enable or disable vibrator notification.
7 - 1
IconDescription
Preliminary Draft 6/19/13, Not for Release
ConnectionsEstablishes network connections settings. See Connections Menu on page 8-1.
PersonalCustomizes buttons, and set SIP options. See Personal Menu on page 7-4.
SystemAdjusts system settings. See System Menu on page 7-9.
Clock & Alarms
The Clock & Alarms settings can be accessed from the Home screen or the Settings menu.
1.On the Home screen, touch the line that displays the time and date or touch > Settings >
Clock & Alarms.
2.The Time settings screen provides access to set the system clock (i.e., Time Zone, Date, and
Time). All scheduled items run according to the settings on the screen. Touch the arrow to the right
of the time zone to open the drop down menu. Select the appropriate time zone from the menu. Set
the correct time and date in the remaining fields and touch OK to save.
7 - 2
Lock
Preliminary Draft 6/19/13, Not for Release
The Lock settings screen provides access to additional password security features that enable you to
prevent an unauthorized person from unlocking the touch screen and accessing the terminal. Select
from two password security options: a Strong Alphanumeric Password or a Simple PIN.
To add password protection:
1.Touch > Settings > Lock .
2.Check the box next to the phrase “Prompt if phone unused for”.
3.Select the length of inactive time you want the terminal to wait before implementing password
security for terminal access.
4.Select Strong Alphanumeric Password or Simple Pin from the Password type drop-down menu.
5.Input the Password you want to use to unlock the terminal.
6.Input the password a second time to Confirm.
7.Touch OK on the tile bar.
8.Select Yes to save the password settings.
To remove password protection:
1.Touch > Settings > Lock .
2.Enter your password.
3.Uncheck the box next to the phrase “Prompt if phone unused for”.
4.Touch OK on the tile bar.
7 - 3
Personal Menu
Preliminary Draft 6/19/13, Not for Release
To access the Personal Menu, touch > Settings > Personal . The screen opens
displaying the Personal Menu.
IconDescription
ButtonsThe Dolphin 60s has six programmable buttons (i.e., Right, Left, Home , Scan, Back,
and End). Touch the Buttons icon to program the buttons to perform specific tasks.
See Buttons on page 7-5.
Owner
Information
PhoneThe Phone icon is present on Dolphin models equipped with WWAN radio (GSM/
Voice
Command
7 - 4
Enter your contact information (e.g., name, company, address, telephone number
and E-mail address).
UMTS/GPRS/EDGE) capabilities. Touch this icon to set up user parameters. See
Options on page 9-6.
Touch the voice command icon to enable or disable voice command for specific
applications, adjust how calendar and notification announcements are performed
and set up voice activated password protection. See Voice Command on page 7-8.
Buttons
Preliminary Draft 6/19/13, Not for Release
The Dolphin 60s has two programmable buttons: Right side button and xxx button. Use the Buttons
setting to reassign the buttons to launch applications or execute commands.
Changing Button Assignments
1.Touch > Settings > Personal > Buttons .
Note: The buttons that appear on this window are the only buttons that can be programmed via the Buttons setting.
You cannot add buttons to this window.
2.To change button assignment, touch on the name of the button in the Button column, and then
select a program or command in the Assign a program drop down list.
3.Touch OK to save.
4.Press the button to verify that the program is launched or action performed.
Available Applications
The Assign a program list contains the applications installed on the terminal. If there is a program
installed that you would like to see in this list, paste a Shortcut to the program in the \\Windows\Start Menu\Programs folder. For instructions about creating shortcuts, see Using File Explorer on page 7-6.
7 - 5
Additional Functions
Preliminary Draft 6/19/13, Not for Release
The Assign a program list also contains the following commands:
CommandDescription
<BACK>Returns to the previous screen.
<Context Menu>Performs the same function as touch-and-hold to open the context menu for the control.
<END>Ends a phone call.
<Home>Returns to the Home screen.
<Input Panel>Opens the soft input panel.
<Left Softkey>Opens the menu or performs the action displayed on the left side of the Command bar.
<None>Nothing happens when the button is pressed.
<OK/Close>Performs the same function as touching OK on the screen.
<Right Softkey>Opens the menu or performs the action displayed on the right side of the Command bar.
<Rotate Screen>Changes the screen orientation from portrait to landscape.
<SCAN>Front panel scan button - Activates the scanner/imager.
<Scan1>Left side button - Activates the scanner/imager.
<Scan2>Right side button - Activates the scanner/imager.
<Scroll Down>Scrolls down in the open application.
<Scroll Left>Scrolls left in the open application.
<Scroll Right>Scrolls right in the open application.
<Scroll Up>Scrolls up in the open application.
<Start Menu>Opens the Start menu.
Using File Explorer
If you do not see the program listed under the Assign a Progr am list, you can either use File Explorer on
the terminal or ActiveSync (see page 7-7) on the workstation to create a shortcut to the program and
place the shortcut in the Start Menu folder.
Note: We recommend that you Copy and Paste Shortcut so that you do not alter your program configurations by
accident. Using Copy and Paste Shortcut (as opposed to Cut and Paste) ensures that the program files
remain where they need to be for the system to find them to perform system functions.
1.Touch > File Explorer .
1.Touch the Program Files folder under My Device.
2.Touch and hold on the program, then touch Copy on the pop-up menu.
7 - 6
3.Navigate back to the My Device root directory, then touch Windows > Start Menu.
Touch the arrow , then
select My Device.
Preliminary Draft 6/19/13, Not for Release
4.Touch and hold a blank area of the window, then touch Paste Shortcut on the pop-up menu.
Note: If there is no blank space available in the window, touch on
Menu > Edit > Paste Shortcut
.
5.Touch to verify that the program now appears on the Start menu.
Using ActiveSync on the Workstation
Here, you are performing the same basic process as on the terminal, except that you are using the
Explore utility (Windows Explorer) to copy and paste the shortcut.
1.Connect the terminal to the workstation using a Dolphin 60s peripheral.
2.Open ActiveSync > Explore and navigate to the program.
3.Right-click on the program and select Create Shortcut.
4.Select the shortcut, right-click, and select Cut.
7 - 7
5.Navigate to the Start Menu folder (Windows > Start Menu > Programs).
Enable or Disable
Voice Command
functionality.
Enable or Disable
Voice Command for
specific applications.
Preliminary Draft 6/19/13, Not for Release
6.Right-click on an empty area and select Paste Shortcut.
7.On the terminal, touch the Start menu.
8.Verify that program appears.
Voice Command
The Voice Command screen provides access to enable or disable voice command for specific applications, adjust how calendar and notification announcements are performed and set up voice activated
password protection.
To access the Voice Command settings, touch > Settings > Personal > Voice
Command .
7 - 8
System Menu
Preliminary Draft 6/19/13, Not for Release
The System menu enables you to verify and sometimes alter system parameters.
To access the System menu, go to > Settings > System . Touch the appropriate icon
to open that system setting.
IconSee Page
AboutSee About on page 7-11.
AudioPanelSee Audio Panel on page 7-11.
BacklightSee Backlight on page 7-12.
BatterySee Battery on page 7-14.
CertificatesSee Certificates on page 7-16.
7 - 9
IconSee Page
Preliminary Draft 6/19/13, Not for Release
EncryptionSee Encryption on page 7-16.
Error
Reporting
External
GPS
HSM
SystemInfo
Managed
Programs
MemorySee Memory on page 7-22.
PowerSee Power on page 7-23.
Regional
Settings
See Error Reporting on page 7-17.
See External GPS on page 7-17.
See HSM SystemInfo on page 7-17.
See Managed Programs on page 7-22.
See Regional Settings on page 7-24.
Remove
Programs
RILSee RIL on page 7-26.
ScreenSee Screen on page 7-26.
SIP ConfigSee SIP Config on page 7-18.
Smart
Sensors
Task
Manager
7 - 10
See Remove Programs on page 7-25.
See Smart Sensor on page 7-19.
See Task Manager on page 7-27.
About
Preliminary Draft 6/19/13, Not for Release
The About system settings screen displays specific information about the terminal. Three information
screens are available: Version, Device ID, and Copyrights.
To access the About system screen, touch > Settings > System . > About .
The Version Screen
Displays the inf ormation about the software, operating system, and processor.
The Device ID Screen
Displays the information the terminal uses to identify itself to other devices. It can be important to know
this information if the Dolphin terminal is going to be part of a networked system of devices.
• Device name: Displays the system’s default name. This is the name used by ActiveSync.
• Description: Displays the description of the device ID.
The Copyrights Screen
Displays important copyright information.
Audio Panel
The Audio Panel settings allow you to specify the Preferred Media Audio Device used for media
playback and audio recording. There are six de vice options: Auto, Handset, Speaker, Headset, Aux, or Bluetooth HS. The Mic Volume slider adjusts the audio input volume (gain) for the preferred device
selected.
Note: Changes made to the Audio Panel only affect media playback
and recording. Phone audio settings are not affected.
To access the Audio Panel settings, touch
> Settings > System > Audio Panel.
Select Auto from the Preferred Media Audio Device list to
set the terminal to automatically detect and use the system
default device.
Note: If you select a preferred device that is not available, for
example, you select Headset but do not connect the headset
to the terminal; the audio defaults to Auto until the preferred
device becomes available.
Touch Reset on the tile bar to discard changes and revert to
the default Audio Panel settings or select OK to save
changes.
7 - 11
Backlight
Check the box next to the
option to enable automatic
backlight dimming.
Touch the arrow, then select
the time increment you want to
elapse before the backlight
automatically dims.
Preliminary Draft 6/19/13, Not for Release
The Backlight system setting enables you to customiz e bac klight functionality f or the display and keypad
(i.e., Send, Home, Back and End buttons). The settings menu contains three tabs: Dim Backlight,
Brightness and Keypad Backlight.
To access the Backlight settings, touch > Settings > System > Backlight.
Dim Backlight
The Dim Backlight settings determine if the backlight dims during periods of non-use and how many
minutes you want to elapse before the backlight automatically dims when the terminal is running on
battery power, external power or USB power.
• Battery Power: The terminal is being powered by the battery.
• External Power: The terminal is being powered by an external power source, e.g., HomeBase,
ChargeBase or Mobile Base.
• USB Power: The terminal is being powered by a USB connection, e.g., the Charge/
Communication cable connected to a workstation (PC) or used in conjunction with the provided
power supply (70e-USB ADAPTERKIT).
7 - 12
Brightness
Check the box to enable
automatic adjustment of the
backlight intensity for low,
medium, and high light
environments.
T ouch and drag the slider to
manually adjust the
Brightness level setting of
the current environment.
Preliminary Draft 6/19/13, Not for Release
The Brightness tab determines the backlight intensity of the display when the terminal is in use. The
settings customize how the terminal responds to the environmental lighting conditions in which the
terminal is being used.
Check the "Auto adjust backlight" box to enable automatic adjustment of the backlight intensity
depending on the operating environment. Once enabled, the terminal automatically adjusts the backlight
intensity to low, medium or high depending on the detected operating environment.
• Low light environments (e.g., dark areas with a limited light source) trigger a low intensity
backlight.
• Medium light environments (e.g., standard lighting in office buildings) trigger a medium intensity
backlight.
• High light environments (e.g., outside environments with bright sunlight) trigger a high intensity
backlight.
When the terminal is in a specific environment, you can manually adjust the brightness level for the
environment by changing the Brightness lev el number from 1 to 8 or b y dragging the slider left or right on
the screen. The highest Brightness level is indicated with an 8.
7 - 13
Keypad Backlight
Preliminary Draft 6/19/13, Not for Release
The Keypad Backlight tab setting determines when the keypad (i.e., Send, Home, Back and End
buttons) backlight is activated. The backlight can be set to turn on with the display, to turn on in dark
environments or to stay turned off.
Battery
The Battery system settings menu contains two tabs: Battery Status and Log Config. The Battery
Status tab provides the status of the battery pack (e.g., Battery Time to Full or Battery Time to Empty,
Voltage, Current, Temperature, Chemistry, and Serial Number). The Log Config Tab allows you to
configure the BatteryLogFile.
To access the Battery system settings, touch > Settings > System > Battery.
Battery Status
The Battery Status tab provides the following information on the battery.
Battery Life Percent
The Battery Life Percent indicates the percentage of charge remaining on the battery.
Battery Time to Full or Empty
When external power is supplied to the terminal, the estimated charging time remaining to achiev e a full
charge is listed. When power is supplied by the battery, the estimated time remaining on the battery
charge is listed.
Note: Time estimates are based on the present voltage and current readings.
7 - 14
Battery Voltage
Battery Status TabLog Config Tab
Preliminary Draft 6/19/13, Not for Release
The Battery Voltage status can range from approximately 3.2 V to 4.2 V.
Battery Current
The Battery Current reflects the charging current going into the battery when it is a positive and the
discharge current when it is negative.
Note: The charging current is always less than current source due to device being in operation.
Battery Temperature
The Battery Temperature indicates the temperature status of the battery.
Battery Chemistry
The Battery Chemistry provides the battery type (e.g., LiIon).
Battery Serial Number
The Battery Serial Number displays the serial number of the authenticated Honeywell battery.
7 - 15
Certificates
Swipe left or right on the
Horizontal scroll or touch
the label (e.g., Root or
Personal) to access the
additional screens.
Preliminary Draft 6/19/13, Not for Release
Certificates shows you the certificates that are recognized by the operating system. The Horizontal scroll
bar at the top of the screen provides access to the three certificate screens: Intermediate, Personal,
and Root.
Encryption
Encryption gives you the option of encrypting files placed on storage cards so that those files cannot be
read by any other device. Check the box to enable file encryption when saving to a storage card.
7 - 16
Error Reporting
Access ScreenHardware ScreenPrograms Screen
Preliminary Draft 6/19/13, Not for Release
Error Reporting gives you the option of enabling or disabling the error reporting function of Windows
Embedded Handheld 6.5.
External GPS
External GPS determines which port a third-party GPS software application can use to access the GPS
receiver.
Note: You need the installation parameters from the GPS manufacturer to configure the connection.
HSM SystemInfo
The HSM SysInfo screen provides important system information including firmware versions, DLL
versions, system parameters , as well as network and radio inf ormation. HSM SysInfo screen contains six
tabs: System, HW, SW, Radio, EXE and DLL.
To output the system information to a te xt file:
1.Touch > Settings > System > HSM SystemInfo .
2.Touch Save on the tile bar.
3.A text file containing the collected system information is created and saved to IPSM/SysInfo.txt.
To upload SysInfo.txt file to a Workstation via ActiveSync:
1.Connect the Dolphin terminal to the workstation using a Dolphin communication peripheral.
2.Open Windows Explorer on the workstation.
3.Navigate to the Mobile Device folder.
4.Double click My Windows Mobile-Based Device and navigate to the IPSM folder.
5.Copy the SysInfo.txt file to your workstation.
7 - 17
SIP Config
SIP Setting TabDial Plan Tab
Preliminary Draft 6/19/13, Not for Release
The SIP Config settings screen enables you to configure Session Initiation Protocol (SIP) f or Voice Ov er
IP (VoIP) and Telephony communication.
To access the SIP Config screens, touch > Settings > System > SIP Config .
7 - 18
Smart Sensor
Touch to customize how
the terminal responds to
motion and object
orientation for ease of
operation and advanced
power management.
Touch to calibrate the
integrated accelerometer
sensor used for motion
detection.
Touch to customize how the
terminal responds to objects
detected close to the touch
screen display.
Preliminary Draft 6/19/13, Not for Release
The Smart Sensor configuration utility enables you to configure the Dolphin’s integrated accelerometer,
and motion settings.
Touch > Settings > System > Smart Sensor .
Motion Settings
Motion Settings enable you to customize how the terminal responds to motion and object orientation for
ease of operation and advanced power management. The Motion Settings menu contains three tabs:
Display, Power, Mana gement, and Event Tracker.
Display
The Display tab provides access to enable or disable Auto Display Orientation. When enabled, the
Dolphin's display automatically s witches between portrait and landscape depending on how you hold the
terminal.
Power Management
The Power Mana gement tab provides access to customize how the terminal responds to object orientation and motion to reserve power and reduce time between charge cycles.
• Face Down:
Save power by turning off the display and/or suspending the device when the terminal is placed
face down.
7 - 19
• Motion Detection:
Preliminary Draft 6/19/13, Not for Release
Modify the Motion Detection settings to wake the terminal from suspend mode or prevent the
terminal from entering suspend mode when motion is detected.
Event Track
The Event Track tab displays an event log summary of detected free fall events exceeding 2 ft. over
500ms. The summary includes the time, date, and duration of the most recent 50 ev ents. Se v eral options
are provided for audible notification of free fall events.
7 - 20
Proximity Sensor Settings
Preliminary Draft 6/19/13, Not for Release
The integrated proximity sensor detects when an object is in close proximity to the entire touch panel
display (e.g., a person's f ace, carrying holster , or tabletop). By def ault, the pro ximity sensor automatically
turns the display and touch panel off when you hold the terminal near your ear during a phone call. The
display and touch panel turn back on when the sensor detects the removal of the object.
To enable this feature at all times, not just during phone calls, check the Enable Proximity Sensor box.
Accelerometer Calibration
Touch Start to calibrate the integrated accelerometer sensor used for motion detection. When calibration
is complete, the “Accelerometer Calibration Finished!” message window appears.
7 - 21
Managed Programs
Preliminary Draft 6/19/13, Not for Release
The Managed Programs screen lists the installation history of programs on the terminal that are
managed by and enrolled to an enterprise domain. Managed Programs is the client-side that works with
the server product System Center Mobile Device Manager (MDM). MDM consists of MDM Gateway
Server and one or more computers that run MDM Device Management Server; MDM Enrollment Server;
and Microsoft SQL Server® 2005 databases.
It lets system administrators:
• provide an authenticated connection to Line of Business (LOB) applications, managed Group Policy,
and application packages.
• use Group Policy and software packages to manage the enrolled Windows phones (enforce policy,
wipe devices, etc.).
• manage the requests for and retrieving of certificates for devices and for creating the Active Directory®
Domain Service objects that represent these devices. By using these objects, you can manage the
devices as if they were members of a domain.
Memory
The Memory applet shows the capacity and usage of the Storage and Program portions of the Flash file
system. The Storage portion includes the IPSM folder, which can be detailed under the Storage Card
tab. When the Program portion becomes too full, you can use the Task Manager to remove any unnecessary tasks.
Main Screen
The Main screen displays the usage statistics of the flash memory.
7 - 22
Storage Card Screen
Preliminary Draft 6/19/13, Not for Release
The Storage Card screen displays the current capacity and usage statistics of the selected memory
type: IPSM, RAMDISK or Storage Card. Select the memory type from the drop-down list. RAMDISK is
selected by default.
• IPSM (Internal Persistent Storage Manager)
Data or programs stored in the IPSM are not affected when the operating system is upgraded.
Autoinstall programs, for example, are stored in \\IPSM\Honeywell\Autoinstall so that they are
always installed after an operating system upgrade or factory reset. Contact a Honeywell
technical support representative for more information on how to perform a factory reset. For
contact information, see Technical Assistance on page 14-1.
• RAMDISK, is a virtual disk that resides in RAM, volatile memory. The virtual disk provides faster
access speed than the ISPM or other system folders. RAMDISK is volatile and is cleared when
a reset (i.e., soft, hard or factory) is performed or power is lost.
• Storage Card
You can install one memory card in Dolphin terminals (see Installing a SIM Card and/or Memory
Card on page 3-16). If a storage card is installed in the terminal, you can select it in the drop-
down list and see capacity and usage statistics for the card.
Power
Power system settings contains two tabs: Battery and Advanced
Touch > Settings > System > Power
7 - 23
Battery Tab
Check the box next to the
option to enable power
time-outs.
Touch the arrow, then select
from the drop-down list, the
number of minutes of inactivity
you want to pass before the
terminal enters Suspend Mode.
Preliminary Draft 6/19/13, Not for Release
The battery tab displays the power level status of the battery. For detailed information on the main
battery, see Battery on page 7-14.
Advanced Tab
The Advanced tab settings determine power time-outs when running on battery power , external power,
or USB power. To reserve power and extend time between charging cycles, configure the terminal to
automatically enter Suspend Mode (see page 2-12) after a specific number of minutes of inactivity.
On battery power: The terminal is being powered by the battery.
On external Power: The terminal is being powered by an external power source, e.g., HomeBase.
On USB Power: The terminal is being powered by a USB connection, e.g., the Charge/Communication
cable connected to a workstation (PC) or used in conjunction with the provided power supply (60s-USB
ADAPTERKIT).
Note: The On USB power time-out setting does not auto-spend the terminal if an ActiveSync connection between
the terminal and workstation is active. Disable ActiveSync on the workstation in order for the device to autosuspend while connected to the workstation.
Regional Settings
Regional Settings enables you to customize the appearance and formatting to your geographic region.
Specifically, you can customize numbers (i.e., number of decimal places allowed), currency (i.e.,using
the $ or €€ symbol), time, and date. These specifications apply to all screens , including the Home screen.
The Region screen displays an overview of the region selected in the drop-down list at the top.
7 - 24
The terminal is loaded with a number of pre-programmed regional settings. Select one from the list and
Preliminary Draft 6/19/13, Not for Release
the results appear on the screen. To see specific settings or to change a specific setting, touch on one of
the items on the horizontal scroll bar (i.e., Region, Number, Date), make the change, and touch OK to
save.
Remove Programs
Remove Progra ms enables you to remo ve prog rams installed on the terminal. Any program (usually CAB
or DLL files) stored in the \\IPSM\Honeywell\Autoinstall folder re-installs after a software upgrade or a
factory reset. If a program is manually removed using the Remove Programs application, the program
does not re-install on a hard or soft reset.
Note: A program (file) does not automatically install if it is added to the \\IPSM\Honeywell\Autoinstall folder and a
hard or soft reset is performed. For information on program installation, see Installing Additional Software on
page 8-11.
For information about the system resets, see Resetting the Terminal on page 2-13. See Honeywell
support for more information on how to perform a factory reset.
1.Touch > Settings > System > Remove Programs .
2.Select the program you want to remove on the list, and then touch Remove.
3.Touch Yes. Wait while the program is removed.
4.Verify that the program no longer appears in the list.
7 - 25
RIL
Preliminary Draft 6/19/13, Not for Release
The RIL Information screen displays useful statistics for the GSM/CDMA WWAN Voice module and
enables you to turn HAC Audio Mode on or off. When HAC Audio mode is enabled, a magnetic/voice
coil activates in the terminal earpiece/receiver speaker allowing the terminal to interface with a hearingaid. To verify whether or not the WW AN radio is enab led, check the Dolphin Wireless Manager (see page
8-6).
HAC Audio Mode
To enable the terminal for use with a hearing-aid:
1.Touch > Settings > System > RIL .
2.Check the box next to Use HAC Audio Mode.
3.Touch OK.
Screen
The Screen system setting contains two screens: Clear Type, and Text Size.
Touch > Settings > System > Screen .
ClearType Screen
The display supports ClearType font rendering, which is a Microsoft technology that dramatically
increases the readability of text on LCD displays.
To enable ClearType font rendering, select Enable ClearType and touch OK.
Note: For more information about ClearType font rendering, visit: www.microsoft.com/typography/
WhatIsClearType.mspx.
7 - 26
Text Size Screen
To change the text size,
move the slider toward
Smallest or Largest. The
Example text changes to
reflect the font change.
Touch OK to save the
new text size.
Preliminary Draft 6/19/13, Not for Release
The Text Size screen enables you to perform font sca ling within certain views of the: Home screen (only
on non-phone devices), Contacts, Calendar, Messaging, and Tasks. Font scaling means that you can
increase or decrease the point size of the font on application windows.
Task Manager
The Task Manager provides information about applications and processes running on your mobile
computer. You can use the Task Manager to monitor the memory and CPU usage of specific applications
and processes. Check the Task Manager when you are receiving out of memory errors or when the
mobile computer is running slowly.
Touch > Settings > System > Ta sk Manager .
7 - 27
Applications
Preliminary Draft 6/19/13, Not for Release
To view the status of the programs running on your mobile computer, touch the Menu button at the
bottom of the screen, then touch View > Applications.
From the application list, you can:
• Touch and hold on an application, then touch Switch To on the pop-up menu.
• Touch and hold on an application, then touch End Task or End All Tasks on the pop-up menu.
Note: Anytime you stop a running program, it frees up memory. To free up memory, return to the running program,
save your data, and close the application.
7 - 28
Processes
Preliminary Draft 6/19/13, Not for Release
To view information about the processes running on the mobile computer, touch the Menu button at the bottom of
the screen, then touch View > Processes.
7 - 29
7 - 30
Preliminary Draft 6/19/13, Not for Release
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.