Hobart Not Found User Manual

Item # _____________________________________

Quantity ___________________________________

C.S.I. Section 11400

LXeR and LXePR

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

STANDARD FEATURES

■ Racks per hour Light Normal Heavy
LXeR 30 24 13
LXePR 38 29 14

■ .62 gallons of water per rack – LXeR

1.14 gallons of water per rack – LXePR

■ Hot water or chemical sanitation units available

■ Steam Elimination and Energy Recovery (LXeR

model only)

■ PuriRinse cycle (Potable water rinse to remove

chemical residue) (LXePR model only)

■ NSF Certied pot and pan cycle on heavy cycle
(LXeR model only)

■ Low chemical alert indicators

■ Sense-A-Temp™ booster heater capable of

70 rise, provided on LXeR models

■ Chemical pump “auto-prime”

■ Advanced Service diagnostics

■ Clogged wash arm sensing

■ Custom cycle selection – light, normal, heavy

■ Automated delime cycle – includes booster

deliming

■ Deep drawn stainless steel tank

■ Microcomputer, top mounted controls with

advanced digital cycle/temperature display

■ Revolving upper and lower anti-clogging wash
arms

■ Snap in revolving upper and lower rinse arms

■ Removable stainless steel scrap screen

■ Corrosion resistant pump

■ Energy Saver mode

■ Automatic pumped drain

■ 17" door opening

■ Dirty water indicator

■ Automatic ll

■ Detergent, rinse aid and delime pumps standard

(plus sanitizer pump on chemical machine)

■ Electric tank heat

■ Two dishracks – one peg and one combination

type

■ Customizable “advansys” button to select
favorites function

■ Auto clean cycle washes down inside of
machine at shutdown

HOT AND COLD

MODELS

❑ LXeR – Energy Recovery
❑ LXePR – PuriRinse

STANDARD VOLTAGES

❑ 120/208-240(3W)/60/1 (LXeR model only)
❑ 120/60/1 (LXePR model only)

OPTIONS AT EXTRA COST

❑ 208-240(2W)/60/1 (LXeR model only)
❑ 208-240/60/3 (LXeR model only)

ACCESSORIES

❑ Power cord kits
❑ Stainless steel base with 6" legs
❑ 17" stainless steel stand with storage
❑ External caster kit
❑ DWT-L Xe drain water tempering kit

Specications, Details and Dimensions on Back.

LXeR and LXePR HOT AND COLD

F40336 – LXeR and LXePR Hot and Cold Page 1 of 4

LXeR

HOT

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

Page 2 of 4 F40336 – LXeR and LXePR Hot and Cold

LXePR

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

COLD

F40336 – LXeR and LXePR Hot and Cold Page 3 of 4

LXeR and LXePR

HOT AND COLD

SPECIFICATIONS

DESIGN: Front opening, equipped for installation in either free-

standing or undercounter-type operations.

CONSTRUCTION: 300 series stainless steel tank, door and top
panel.

PUMP: Centrifugal-type, integral with motor, horizontally
mounted. Pump capacity 38 gpm.

MOTOR: Single phase, furnished for all electrical specications.
Factory sealed lubrication. Inherent overload protection with auto
reset.

WASH AND RINSE CYCLE: Complete automatic type, controlled
by solid-state electronics. Cycle may be interrupted any time by
opening door. Cycle continues when door is closed.

• Initial cycle lls wash tank, to be recirculated each wash cycle.
Some wash water is drained off before rinse cycle. Rinse cycle
refreshes wash water and tank heat.

RINSE PUMP: Powered by a single phase motor, the rinse pump
is made of high strength engineered composite material.

BLOWER: The blower is a 60mm x 300mm tangential wheel
powered by a 2-pole single phase motor for quiet and reliable
operation, LXeR only.

CONDENSER COIL: The condensing system uses a tube and n
coil constructed of copper and corrosion resistant aluminum.
The condenser coil allows for energy recovery from waste heat
in the moisture laden air that would normally escape into the
environment after a dishwashing cycle, LXeR only.

RINSE AND SANITATION:

• LXeR: Sanitation is accomplished by means of a built-in
booster heater designed to raise temperature of water to a
minimum of 180°F from an incoming water temperature of
55°F.

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

• LXePR: Sanitation is accomplished by injection of proper
amount of sodium hypochlorite solution (liquid bleach) into
nal rinse water to achieve a minimum of 50PPM sanitizing
solution. Injection of sodium hypochlorite is accomplished
by a built-in sanitizing chemical pump. Minimum required hot
water temperature is 120°F.

– Potable water rinse to remove chemical residue.
– To be used with sanitizer approved for use with post

sanitizing rinse

• CHECK SANITIZER CONCENTRATION: PuriRinse must be
off (hold Wash button for 5 seconds). Verify that there is suf-
cient chemical supply. Run cycle and use test trips on wetted
surface of glasses after cycle is complete. If concentration is
below minimum required, contact your local Hobart Service
ofce.

ENERGY RECOVERY: Heat energy is recovered from the con­densation of vapors in the chamber at the end of each cycle. This
pre-heats the water for the next rinse cycle from 55°F up to 140°F.

PUMPED DRAIN: Machine automatically drains water through a
built-in pump. Maximum 38" drain height permitted.

ELECTRIC BOOSTER HEATER: 4.9 KW electric booster with

Sense-A-Temp™ technology adequately sized to raise 55°F inlet
water to 180°F, with the aid of the energy recovery system.

RACKING: Machines accommodate racks from 10" x 20" to 20" x
20". Also accepts 16" x 18" cafeteria trays.

NOTE: Certain materials, including silver, aluminum and pewter
are attacked by Sodium Hypochlorite solution in the chemical
sanitizing mode of operation.

SPECIFICATIONS: Listed by Underwriters Laboratories Inc. and
NSF International.

MACHINE RATINGS

Racks per Hour Rate 38 29 14 30 24 13

Dishes per Hour (25 per Rack Avg.) 950 725 350 750 600 325

Glasses per Hour (36 per Rack Avg.) 136 8 1044 504 1080 864 468

Controls Microcomputer

Tank Capacity - Gallons 2.9

Overall Dimensions - H x W x D 321⁄2 " x 2315⁄16" x 259⁄16" 321⁄2 " x 2315⁄16" x 2613⁄16"

Cycle Time - Seconds 94 124 254 120 146 275

Tan k H e at 1.8 KW

Electric Booster Heater N/A 4.9 KW

Water Usage Per Rack - Gallons 1.14 .62

Drain Design Pumped

Door Opening Height 17"

Detergent Pump Standard

Rinse-Aid Pump Standard

Delime Pump Standard

Sanitizer Pump Standard N/A

Chemical Prime (auto prime) Standard

Peak Drain Flow - GPM 4.0

Advanced Service Diagnostics Standard

Advanced Cleaning Cycle Standard

70°Rise Sense-A-Temp™ Booster Heater N/A Standard

Incoming Water Temperature Required (minimum) 120° 55°

Light Normal Heavy Light Normal Heavy

LXePR LXeR

As continued product improvement is a policy of Hobart, specications are subject to change without notice.

Page 4 of 4 F40336 – LXeR and LXePR Hot and Cold

F40336 (REV. 03/13) LITHO IN U.S.A. (H-01)