machine consisting of a load section with power
recirculating prewash, a 4 foot power wash, nal
rinse section. Included with each machine will be
exible plastic strip curtains to control over spray.
CONSTRUCTION: Stainless steel tank and chambers
with No. 3 polish on appearance surfaces. Frame,
legs and feet to be constructed of stainless steel.
Inspection doors to be chamber width.
PUMPS: Recirculating stainless steel pumps with
stainless steel impellers. Pump housing has easy to
remove coverplate for access to impeller. All pumps
are self-draining. 150 gpm prewash; 292 gpm power
wash, 8 gpm dual rinse.
MOTORS: Totally enclosed fan cooled design, with
inherent overload protection. Prewash and power
wash to be 3 H.P. each, conveyor 1⁄2 H.P., dual rinse
1
⁄6 H.P. Available in electrical specications of
208-240/60/3 and 480/60/3.
CONTROLS: A stainless steel control center with
electronic digital controls mounted at eye level.
Power “On/Off” and “Start/Stop” switches integrated
into keypad. Digital display indicates door open, low
temperature alert, tank/nal rinse temperatures and
other pertinent operating data. Additional “Start/
Stop” switches are located at each end of machine.
FLIGHT-TYPE CONVEYOR: Stainless steel side
links, tie rods and conveyor tracks. Injection molded,
resilient Duraex ight links.
VENT: Single built-in vent duct with dampers
mounted in cleanable cross duct.
RECIRCULATING PREWASH SECTION: Prewash
compartment is tted with upper and lower wash
arms. Prewash ush down for prewash tank bed.
Large removable one piece perforated stainless steel
screen sloped downward to deep stainless steel
scrap basket.
TANK HEAT: Power wash and dual rinse water temperature is thermostatically controlled. Low water
protection is provided. Specify either electric or
steam heat for the wash. Dual rinse is electric only.
DUAL RINSE/FINAL RINSE: Arms removable without
tools.
CONVEYOR DRIVE UNIT: Powered by a 1⁄2 H.P.
motor. Trip mechanism provided on unload section.
Jam protection is provided by load sensing switch at
drive platform. Conveyor speed adjustment of 4 fpm
to 6.3 fpm is provided in the main control box.
DRAINS: Manual, hand operated, located in each
tank.
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
BLOWER DRYER
To assist and promote drying of tableware and trays
by forced circulation of high velocity heated air
through the clean dishware section of the Hobart
Flight-type dishmachines.
Blower dryer is built on a minimum 9' unloading
section only. Hooded chamber/blower section covers
66" length of conveyor, to provide adequate drying
time.
• CONSTRUCTION: All sheet metal construction
is 16 gauge stainless steel. Large insulated
inspection door on front side of machine provides
access. Stainless steel wrap-around encloses
entire external component assembly, consisting
of steam or electric heaters, motor and blower.
• ELECTRIC HEATER: Nine Incoloy sheathed
electric heaters for a total of 20 KW heating
capacity. Thermostatic over temperature
protection is standard. Electric specications are
208/60/3, 240/60/3 or 480/60/3.
• STEAM COIL: Heavy-duty, high-efciency nned
tube-type heat exchanger. Copper tubes and
aluminum ns with galvanized frame. 11⁄2" F.P.T.
steam connection 3⁄4" F.P.T. condensate return
connection. Steam requirements are 75 pounds
per hour at 20 P.S.I. or about 2.2 boiler H.P.
Maximum allowable steam pressure is 25 P.S.I.
Operating pressures above 25 P.S.I. may require
a pressure reducing valve.
• BLOWER: Industrial fan-type with squirrel-cage
type wheel. Housing of welded construction
throughout.
Blower is directly driven by a 2 H.P. motor with
sealed ball bearings. Motor construction is of
open drip proof design. The blower dryer is totally
enclosed by removable stainless steel panels
mounted on top of the dryer chamber. Exhaust
requirement is 1000 C.F.M. (at standard air conditions). Sound level at end of 9-foot unloading
section, with full machine operation is less than
85 DBA, dened by A.N.S.I. (American National
Standards Institute) Standard No. S1.1-1960 ...
below existing O.S.H.A. rules. At loading end of
dishwasher, sound level is 80 DBA or less.
The blower motor is provided with inherent over-
load protection and a manual reset. Furnished only
in three-phase electrical specications of the basic
Flight-Type Model in 208-240/60/3 and 480/60/3.
The controls are placed in a convenient panel that
lets operators verify proper operation and temperatures at a glance. Digital
display indicates the
unit is on, and conrms
that the doors are
closed. Automatic door
interlocks prevent the
pump and conveyor from operating if the doors are
open. Easy-to-read digital display indicates accurate
temperatures of the 160°F wash and 180°F nal rinse
— critical for proper HACCP system record-keeping.
Stainless steel pump is
built for long life.
The stainless steel pump
housing and impeller offer
greater durability and long
life. The pump motor is
totally enclosed and fan
cooled (TEFC) to protect
it from water spray during
dishroom clean-up. The
pump is also externally mounted to the frame for
added rigidity and easy access to the clean-out port.
Scrap baskets capture
food particles and are
easy to clean.
The sloped screens that
carry scraps to the scrap
baskets are steeper, so
less soil gets into the
tanks. The basket opening
is larger for easy cleaning and basket handles have
been designed for easy lift-out access.
The conveyor on the
FT900SDBD is wider so
it can handle more ware.
Result: more volume and versatility, quicker work.
Its speed is servicer adjustable for the type of ware,
soiled condition, or workforce requirements. It can be
adjusted from 4 to 6.3 feet per minute.
Optional Energy
Recovery system.
The optional Energy
Recovery system
captures escaping
heat and steam from
the exhaust air and
uses a heat exchanger to recycle it into energy.
This free energy is used to preheat the incoming
water supply before it enters the booster heater. The
cold ground temperature water passes through a
heat exchanger positioned directly in line with the
machine’s exhaust system to capture the energy
from the exhaust air to elevate the temperature of the
water to 128° before it enters the booster heater.
Flush arm keeps
load end clean.
The load end also has a readily removable ush arm to rinse
food scraps into the prewash
area scrap basket.
Self-draining pumps help keep water clean.
Pumps are self-draining when the machine is shut
down and drained, so there is no residual water left in
the pumps.
The FT900SDBD Series
saves water and energy.
The unit is designed to cut water
and energy usage, yet provide
effective cleaning and sanitizing
that meet NSF International
requirements.
This is achieved through a care fully balanced ratio of water
ow to pressure. At 292 gallons
per minute (gpm), the machine offers excellent
wetting and ooding over ware. Insulated doors also
reduce heat loss. The unit’s 1.2 gpm/72 gallons per
hour rinse (the lowest in the industry on a standard
machine) or 1.4 gpm/84 gallons per hour rinse
(6" HTS) ow rate saves both water and the energy to
heat it.
Installation is quick and easy with modular
design, minimal wiring connections, and
single point vent.
Modular design means the FT900SDBD Series installs
quickly, and reliably. Sections t through 42" doors.
The control panel is already in place, premounted to
the power wash/dual rinse section.
Wiring connections are
minimal, and there is only
a single vent connection,
saving time and expense.
The control box uses a
“single plane” circuitry
design for easy accessibility during installation and service. The FT900SDBD
Series is ready to run quickly.