DESIGN: Fully automatic, ight-type dish machine
consisting of a load section, power recirculating
prewash, power wash, power rinse, and dual rinse/
nal rinse section. Included with each machine will be
exible plastic strip curtains to control overspray.
CONSTRUCTION: Stainless steel tank and chambers
with No. 3 polish on appearance surfaces. Frame,
legs and feet to be constructed of stainless steel.
Inspection doors to be chamber width.
PUMPS: Recirculating stainless steel pumps with
stainless steel impellers. Pump housing has easy
to remove coverplate for access to impeller. Wash
pumps are self-draining.
MOTORS: Totally enclosed fan cooled (TEFC) design
with overload protection. Pump motors to be 5 H.P.
for prewash and wash, 31⁄2 H.P. for power rinse, and
conveyor motor to be 1⁄3 H.P. Available in electrical
specications of 208/60/3, 240/60/3 and 480/60/3.
CONTROLS: A stainless steel control center with
electronic digital controls mounted at eye level.
Power “On/Off” and “Start/Stop” switches integrated
into keypad. Digital display indicates door(s) open,
low temperature alert, tanks/nal rinse temperatures
and other pertinent operating data. Additional “Start/
Stop” switches are located at each end of machine.
Conveyor speed button included on the control
center to provide for adjustable speed conveyor.
FLIGHT-TYPE CONVEYOR: Stainless steel side
links, tie rods and conveyor tracks. Injection molded,
resilient Duraex ight links.
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
VENT: Indirect main and load Vent connections with
integral powered fans.
RECIRCULATING PREWASH SECTION: Prewash
compartment is tted with upper and lower wash
arms. Large removable one piece perforated stainless
steel screen sloped downward to deep stainless steel
scrap basket.
TANK HEAT: Power wash, power rinse and dual
rinse tank water temperatures are thermostatically
controlled. Low water protection is provided. Specify
either electric or steam heat.
ENERGY RECOVERY: Energy Recovery system
operates with a cold water line, capturing energy from
exhaust air and using it to elevate the temperature of
the water entering the booster heater.
CONVEYOR DRIVE UNIT: Powered by a 1⁄3 H.P.
motor. Trip mechanism provided on unload section.
Jam protection is provided by load sensing switch
at drive platform. Conveyor speed adjustment of 4.0
feet per minute to 8.5 feet per minute is provided on
the digital display keypad, and can be factory set, if
requested.
DRAINS: Manual, hand-operated, located at each
tank.
BLOWER DRYER: Each blower dryer module
includes (2) 2 H.P. fan motors with sealed ball
bearings and overload protection. 31" door access
provided. Multiple blower dryer modules available.
The digital controls are
placed in a convenient
panel that lets operators verify proper operation and
temperatures at a glance. Digital display indicates
the unit is on, and conrms that the doors are
closed. Automatic door interlocks prevent the pump
and conveyor from operating if the doors are open.
Easy-to-read digital display indicates accurate temperatures of the 150°F wash, 160°F power rinse,
160°F dual rinse and 180°F nal rinse — critical for
proper HACCP system record-keeping.
Stainless steel pump is built for long life.
The stainless steel pump housing and impeller offer
greater durability and long life. The pump motor is
totally enclosed and fan cooled (TEFC) to protect it
from water spray during dishroom clean-up.
Scrap baskets capture food particles
and are easy to clean.
The sloped screens that carry scraps to the scrap
baskets are steeper, so less soil gets into the tanks.
The basket opening is larger for easy cleaning and
basket handles have been designed for easy lift-out
access. The load section also contains removable
scrap baskets. All scrap baskets and strainers are
stainless steel for strength and durability.
The conveyor
on the FT1000
Series is wider
so it can handle
more ware.
Result: more volume and versatility, quicker work.
Its speed is easily adjustable on the digital display
keypad for the type of ware, soiled condition, or
workforce requirements. It runs at 4.0 - 8.5 feet per
minute, and can ship from the
factory at a specic speed, if
requested.
Start/Stop switches.
Are included at both the load and
unload end for ease of use and
convenience.
Energy Recovery system reclaims heat for energy.
The Energy Recovery system’s heat exchanger
captures escaping heat and steam from the exhaust
air in the dish machine, and uses it to preheat the
incoming cold water supply to 120°F before it enters
the booster heater. In addition to energy savings, the
Energy Recovery system provides a viable use for this
otherwise exhausted heat.
The FT1000
Series saves
water and
energy.
Provides effective cleaning
and sanitizing
that meets NSF
International
requirements.
This is achieved through a carefully balanced ratio of
water ow to pressure. Insulated doors and thermal
layered curtains at load also reduce heat loss. The
unit’s 78 gallons per hour rinse ow rate saves both
water and the energy to heat it. Wash and rinse
systems have been optimized for thorough cleaning,
and include side wash and side rinse for consistent
coverage.
Self-draining wash pumps help keep water clean.
Pumps are self-draining when the machine is shut
down, so there is no residual water left in the pumps.
Installation is quick and easy with modular design
and minimal wiring connections.
Modular design means the FT1000 installs quickly
and reliably. The control panel is already in place,
premounted to the dual rinse/nal rinse section.
The control box uses a “single plane” circuitry design
for easy accessibility during installation and service.
The FT1000 is ready to run quickly.
Blower Dryer provides superior results.
A double blower and side air diverters on each blower
dryer module provide consistent air ow. Doors
provide easy access to chamber. Multiple blower
dryers can be ordered and are easily assembled with
a modular design.