Item # _____________________________________
R
Quantity ___________________________________
C.S.I. Section 11400
C44A/C44AW
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STANDARD FEATURES
■ 202 racks per hour – C44A
■ 126 racks per hour – C44AW
■ Opti-RinSe™ system
■ Ball detent clutch conveyor drive mechanism
■ Top mounted controls
■ Stainless steel anti-clogging wash arms
■ Stainless front panel, frame and legs
■ Automatic fill
■ Auto-timer
■ Scrap screen and deep basket system
■ Stainless steel self-draining pump and impeller
■ Fixed pump intake screen
■ Door actuated drain closure
■ Door interlock switch on all doors
■ Vent fan control
■ Convertible hot water or low temp final rinse
■ Booster heater control
DISHWASHER
MODEL
❑ C44A – Dishwasher
❑ C44AW – Dishwasher (12% lower water use)
ACCESSORIES
❑ Stainless steel vent hoods
❑ Direct drive unloader
❑ Side loader
Specifications, Details and Dimensions on Inside and Back.
DIRECTION OF OPERATION
❑ Right to Left
❑ Left to Right
VOLTAGE
❑ 208-240/60/1
❑ 208-240/60/3
❑ 480/60/3
OPTIONS AT EXTRA COST
❑ Stainless steel pressureless 15 kw or 30 kw
booster heater
❑ Single point electrical connection (does not
include booster heater)
❑ 6" higher than standard chamber
❑ Conveyor dwell
❑ Side loader
❑ Blower-dryer
C44A/C44AW DISHWASHER
F-39950 – C44A/C44AW Dishwasher Page 1 of 12
C44A/C44AW
DISHWASHER
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
C-LINE DISHWASHER NOW STANDARD WITH MORE PRODUCTIVE FEATURES THAN EVER . . .
Inside and out the C-Line Hobart dishwashers are packed with standard components and design innovations
that make them the biggest value in the dishwasher industry.
Wash Arms. Computer-designed wash arms
resist clogging, easily removed for cleaning
(C-44A shown).
Stainless Steel Self-Draining Pump and Impeller.
Pump and impeller are stainless steel for maximum
durability. A fixed pump intake screen prevents debris
from entering into the pump.
Lift-Out Scrap Basket. Screen design sheds soil more
easily than flat screens, reduces frequency of cleaning
— easy to empty large soil particles . . . Just lift out
scrap basket under screens.
OPTIONAL BOOSTER HEATER
Built-in Pressureless Stainless Steel Booster Heater.
Interwired and interplumbed. Saves on installation and
saves floor space. Simplifies operation with just one
switch to power dishmachine and booster.
Opti-RinSe™. Hobart’s exclusive patent pending
Opti-RinSe™ significantly reduces operating cost by
reducing rinse water and the energy required to heat
the water. The unique spray pattern uses large droplets
to more efficiently sanitize the ware.
OTHER STANDARD FEATURES . . .
• Low-Temp Convertibility In Field. Order your
C-Line with hot water sanitizing or energy-saving low
temperature chemical sanitizing – then, if require
ments change, convert from one mode to the other in
the field. An exclusive feature – standard from Hobart.
• Auto-Fill. One button automatic fill ensures optimum
tank level, and the simplest operation.
• Auto-Timer. Automatically activates the warewasher
when a rack enters the machine, and after the last
rack has passed, shuts off the pump and conveyor
while maintaining tank heat temperature. Extends
machine life, requires less operator attention and
promotes significant energy savings.
• Door Actuated Drain Closure. Closing the door
automatically actuates drain closure, eliminates extra
manual steps, insures that closure is in the correct
position.
• Vent Fan Control and Booster Heater Control.
Allows for interconnection to dishwasher.
-
Page 2 of 12 F-39950 – C44A/C44AW Dishwasher
C44A/C44AW
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
DISHWASHER
AVAILABLE OPTIONS AND ACCESSORIES . . .
Flexibility is synonymous with Hobart C-Line dishwashers. If your operation demands a dishwasher with a
vent hood, an extended hood . . . a recirculating prewash, just specify the combination of options that suit
your needs.
OTHER AVAILABLE OPTIONS . . .
Condenser, blower-dryer, conveyor dwell, steam booster
heater, and a single-point electrical connection for electric heat
machines.
C44A C44AW
Side Loader. Save up to 20 square feet in
the dishroom layout with an optional C-Line
Side Loader. Racks are indexed 90° into
the dishwasher automatically – a feature
that cuts space and reduces labor dramatically. Your dishroom team will appreciate
this feature.
Extended Hood Vent Hood
C-Line Dishwashers are available with vent
hoods or extended hoods, each with vent
stack and locking-type damper, and both
designed to fit either end of the dishwasher.
Machine Ratings (Mechanical)
Racks per hour (19
Conveyor Speed - feet per minute
Dishes per Hour (Average 25 per rack)
Glasses per Hour (Average 45 per rack)
Floor Space - Table to Table (Inches) 44
Overall Dimensions - H x W x D (Inches) 701⁄4 x 451⁄4 x 301⁄4
Motor H.P. 2
Conveyor Drive H.P.
Blower-Dryer - Motor H.P. (if used)
Electric Blower Dryer
Heating Coils (if used)
Blower-Dryer -
Flowing Steam if used (25 PSIG MAX.)
Number of Tanks
Tank Capacity -
Pump Capacity -
Gallons per Minute - Weir Test
Heating Equipment -
(For keeping power wash hot)
Gas Burners (with Natural Gas) BTU per hr.
Steam Injectors
Electric Heating Unit - Size Used
Optional Booster Heater / Final Rinse 15 KW / 30 KW
Rinse - Minutes operated during hour of
maximum operation
Final Rinse Flow - Gals. per min.
At 15 PSI Flow Pressure
At 20 PSI Flow Pressure
Final Rinse Flow - Gals. per hr. - MAXIMUM
At 15 PSI Flow Pressure
At 20 PSI Flow Pressure
Rinse 20 PSI Flow Pressure
Gal./Rack
Steam Consumption -
Pounds per hr. - MAXIMUM
Approx. 30 lbs. per hr. = 1 boiler H.P. (BHP)
Dishwasher, based on 20 PSI steam and
on customersupplying final rinse water
at 180°F maximum
Steam Booster,
20 PSI water flowing - 130°F entering
water raised to 180°F min.
Exhaust Requirements -
Cubic Feet per minute
Discharge end
Peak Rate of Drain Flow - Gallons per minute.
(Initial rate with full tank) 38
Shipping Weight Crated - Approximate lbs.
3
⁄4" x 193⁄4") 202 126
5.6 max. 3.5 max.
5,025 3,150
9,045 5,670
1
⁄6
2
42.0 KW
Based on 20 PSI
Gallons 23.0
151 104
1.83 1.19
2.13 1.36
110 71
128 82
.64 - 180°F – .64 - 140°F .65 - 180°F – .65 - 140°F
if used on 20 PSI steam -
60 37
Entrance End 200
Discharge End
w/Blower Dryer 1400
110
1
78,000
Regulated 3⁄4"
Regulated 15 KW
60
Hot Water Sanitizing -
Chemical Sanitizing
65
400
613
F-39950 – C44A/C44AW Dishwasher Page 3 of 12
C44A/C44AW
DISHWASHER
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 4 of 12 F-39950 – C44A/C44AW Dishwasher
C44A/C44AW
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
DISHWASHER
F-39950 – C44A/C44AW Dishwasher Page 5 of 12
C44A/C44AW
ELECTRIC L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 6 of 12 F-39950 – C44A/C44AW Dishwasher
C44A/C44AW
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
ELECTRIC R-L
F-39950 – C44A/C44AW Dishwasher Page 7 of 12
C44A/C44AW
GAS L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 8 of 12 F-39950 – C44A/C44AW Dishwasher
C44A/C44AW
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
GAS R-L
F-39950 – C44A/C44AW Dishwasher Page 9 of 12
C44A/C44AW
STEAM L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 10 of 12 F-39950 – C44A/C44AW Dishwasher
C44A/C44AW
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STEAM R-L
F-39950 – C44A/C44AW Dishwasher Page 11 of 12
Printed On Recycled Paper
C44A/C44AW
DISHWASHER
SPECIFICATIONS: Meets requirements of A.S.S.E. Standard
No. 1004.
DESIGN: Fully automatic, high-temperature single-tank, rack-
type dishwasher with flexible strip curtains at ends of chamber
and between wash and final rinse compartments. Large inspection door located in front of machine provides easy access to
wash arms, rinse arms, rinse pan strainer, strainer basket, front
and rear strainers, and pump intake screen. Door guided for
ease of operation and long life. Design provides for changing of
direction of operation in the field. Length of machine inside tank
(at table connection) 44". Machine designed to clean and sanitize
with hot water 160°F wash and 180°F (minimum) final rinse.
Water hardness must be controlled to 4-6 gr. for best results.
Automatic interlocks shut off pump and conveyor if door is
opened when machine is in operation.
CONSTRUCTION: Tank and chamber constructed of #16 gauge
stainless steel, arc-welded. Unitized, welded stainless steel tank,
frame and stainless steel legs. Chamber, control box, door, and
front trim panel are polished, satin finish.
PUMP: Recirculating stainless steel pump with stainless steel
impeller and face seal with stainless steel metal components and
ceramic seat. Readily removable motor/impeller assembly
permits quick inspection. The pump is self-draining. All piping
distributing water to the upper and lower wash arms is stainless
steel tubing.
PUMP MOTOR: Built for Hobart: 2 horsepower, grease-packed
ball bearings, splashproof, ventilated with manual resettable
inherent overload protection. Available in electrical specifications
of 208-240/60/1, 208-240/60/3, 480/60/3. Also available are
200-240/50/1, 200-240/50/3, 380-415/50/3, and 600/60/3, not
submitted for UL Listing.
CONTROLS: A stainless steel control center with power “on/off”
and “start/stop” switches is mounted on top of machine. Machine
control circuitry components will be operated from a 120 volt
control circuit transformer. Auto-timer is standard equipment. An
“auto/manual” switch is located on the left side of control box
for bypassing the auto-timer feature. Electrical components are
completely wired with 105°C, 600V thermoplastic insulated wire
with stranded conductors routed through Listed electrical conduit
or covered wireway built into the front of the machine above tank
water level.
CONVEYOR: Dual rack drive, with stainless steel pawls both
sides of conveyor, designed to eliminate interference with wash
and rinse spray patterns. Racks conveyed automatically through
wash and rinse sections and onto clean dish table. Factory set
overload mechanism on conveyor drive prevents damage to
machine or racks, should movement of racks be obstructed. Rack
tracks, conveyor structure, and drive units of stainless steel for
193⁄4" x 193⁄4" racks as standard. Conveyor speed: 5.6 FPM,
C44A; 3.5 FPM, C44AW.
DRIVE MOTOR: Built for Hobart, 1⁄6 horsepower gearmotor,
ventilated with manual, resettable inherent overload protection.
Available in electrical specifications of 208-240/60/1,
208-240/60/3, 480/60/3. Also available, but not submitted for
UL Listing are 200-240/50/1, 200-240/50/3, and 380-415/50/3.
POWER WASH: Wash tank is equipped with upper and lower
stainless steel wash arms with specially shaped nozzles having
large openings and arranged to effectively direct water jets to all
ware surfaces. Both upper and lower wash arms, along with wash
arm end caps, are easily removable for cleaning without use of
tools. Removable perforated stainless steel strainer pans support
a deep perforated stainless steel basket. Basket and strainer
pans (2) can be removed without lower wash arm removal.
FINAL RINSE: Stainless steel upper and lower rinse arms have
single rows of nozzles. Rinse is automatically activated by racks
in passing. Final rinse water line is equipped with vacuum
breaker in downstream side of electrically operated solenoid
valve in common piping system. Design provides for collection
As continued product improvement is a policy of Hobart, specifications are subject to change without notice.
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
and division of final rinse water after use to wash tank and drain.
Rinse agent dispenser injection port provided in final rinse
piping above chamber. Final rinse flow rate: 2.13 GPM, C44A;
1.36 GPM, C44AW.
Low Temp Final Rinse – Sanitizer agent (5.25% sodium
hypochlorite – bleach) and rinse agent dispenser injection ports
provided in final rinse piping above chamber. Caution: Certain
materials, including silver, aluminum, and pewter are attacked
by sodium hypochlorite (bleach) in the chemical sanitizing
dishwasher mode of operation.
FILL: Fill water line is equipped with vacuum breaker on downstream side of electrically operated solenoid valve in common
piping system, for automatic maintenance of tank level. Fill is
interrupted whenever a door is opened.
DRAIN AND OVERFLOW: Large bell-type automatic overflow
and drain valve controlled from inside of machine. Drain automatically closed by lowering inspection door. Drain seal is large
diameter, high temperature o-ring. Stainless steel drain seat.
Drain casting can be plumbed from load or unload end of
machine.
STANDARD EQUIPMENT: Sealed dial-type thermometers
indicate temperatures of wash and final rinse water. Positive low
water protection for tank heat. Plastic strip curtains throughout
machine. Stainless steel control box. Built-in wireway. Drain is
automatically closed when inspection door is closed. Stainless
steel adjustable feet. Stainless steel hang-on/drop-in-place front
trim panel. Automatic tank fill. Door interlock. Auto-timer. Vent fan
and booster heater controls.
OPTIONAL EQUIPMENT AT EXTRA COST:
WASH TANK HEATING
ELECTRIC: One electric incoloy sheathed immersion heater
(15 KW) removable from inside tank. Tank water temperature is
controlled by solid-state thermostat with positive low-water
protection and magnetic contactor. (Disconnect switches not
furnished.) Heating element is additionally protected by a high
limit device mounted on the surface of the element.
STEAM: One-inch stainless steel steam injector or one-inch
stainless steel steam coils (for contaminated steam). Tank water
temperature controlled by solid-state thermostat with positive
low-water protection. Steam supplied to machine through high
temperature steam solenoid valve and line strainer.
GAS: Regulated power immersion tube gas burner system. Tank
water temperature is controlled by solid-state thermostat and a
blower with a centrifugal switch. Positive low water protection is
provided. Immersion tube is additionally protected by a high limit
device mounted on the surface of the tube. A solid-state ignitor
board controls the gas valve and provides flame ignition.
A transformer steps the control circuit voltage down from 120
volts to 24 volts to power the ignitor board and gas valve.
For natural gas, gas pressure to burner (customer connection)
not to exceed 7" W.C.
For LP gas, gas pressure to burner (customer connection) not to
exceed 11" W.C.
If gas pressure is higher than 7" W.C. natural or 11" W.C. LP, a
pressure regulating valve must be supplied (by others) in the gas
line to the dishwasher.
OPTIONAL EQUIPMENT AT EXTRA COST:
Stainless steel pressureless booster heater. Stainless steel vent
hoods with vent stack and locking-type damper. Stainless steel
extended hoods with vent stack and locking type damper. SL-23
and SL-30 side loaders without hood. Six inches higher than
standard. Steam or electric blower dryer (3-phase only). Floormounted steam booster. 193⁄4" x 193⁄4" peg and combination and
miscellaneous racks.
Single-point electrical connection for electric heat machines
(3-phase only, does not include booster heater). Conveyor dwell.
Table limit switch.
Page 12 of 12 F-39950 – C44A/C44AW Dishwasher
F-39950 (REV. 2/06) LITHO IN U.S.A. (H-01)
Loading...