Hikvision DS-K2601, DS-K2602 User Manual

DS-K2600 Series Access Controller

User Manual

Access Controller·User Manual

User Manual

Product Name

Serials

Access

Controller DS-K2601 Serials Access Controller

DS-K2602 Serials Access Controller

DS-K2604 Serials Access Controller

It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product.

About this Manual

This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision

Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be

reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.

Trademarks

and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

Support

Should you have any questions, please do not hesitate to contact your local dealer.

Access Controller·User Manual

Regulatory Information FCC Information

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected. —Consult the dealer or an experienced radio/TV technician for help.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the R&TTE Directive 1999/5/EC, the EMC Directive 2014/30/EU, the LVD

Directive 2014/35/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated

collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Access Controller·User Manual

iii

Preventive and Cautionary Tips

Before connecting and operating your device, please be advised of the following tips:

• Ensure unit is installed in a well-ventilated, dust-free environment.

• Keep all liquids away from the device.

• Ensure environmental conditions meet factory specifications.

• Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of

dropping it may cause damage to the sensitive electronics within the unit.

• Use the device in conjunction with an UPS if possible.

• Power down the unit before connecting and disconnecting accessories and peripherals.

• A factory recommended HDD should be used for this device.

Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the manufacturer.

Access Controller·User Manual

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions:

Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.

Warnings

 All the electronic operation should be strictly compliance with the electrical safety regulations,

fire prevention regulations and other related regulations in your local region.

 Please use the power adapter, which is provided by normal company. The power consumption

cannot be less than the required value.

 Do not connect several devices to one power adapter as adapter overload may cause over-heat

or fire hazard.

 Please make sure that the power has been disconnected before you wire, install or dismantle

the device.

 When the product is installed on wall or ceiling, the device shall be firmly fixed.  If smoke, odors or noise rise from the device, turn off the power at once and unplug the power

cable, and then please contact the service center.

 If the product does not work properly, please contact your dealer or the nearest service center.

Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)

Cautions

 Do not drop the device or subject it to physical shock, and do not expose it to high

electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).

 Do not place the device in extremely hot (refer to the specification of the device for the detailed

operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The appropriate operation temperature is 0℃ to +45℃, and the storage temperature should be -10℃ to +55℃.

 The device cover for indoor use shall be kept from rain and moisture.  Exposing the equipment to direct sun light, low ventilation or heat source such as heater or

radiator is forbidden (ignorance can cause fire danger).

 Do not aim the device at the sun or extra bright places. A blooming or smear may occur

otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.

 Please use the provided glove when open up the device cover, avoid direct contact with the

device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.

Warnings Follow these safeguards to prevent serious injury or death.

Cautions Follow these precautions to prevent potential injury or material damage.

Access Controller·User Manual

 Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do

not use alkaline detergents.

 Please keep all wrappers after unpack them for future use. In case of any failure occurred, you

need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.

 Improper use or replacement of the battery may result in hazard of explosion. Replace with the

same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

Access Controller·User Manual

Table of Contents

Chapter 1 Product Description ................................................................................................. 1

1.1 Overview .............................................................................................................................. 1

1.2 Main Features ...................................................................................................................... 1

Chapter 2 Component Description ........................................................................................... 3

Chapter 3 Terminal Connection ................................................................................................ 5

3.1 Terminal Description ............................................................................................................ 5

3.1.1 DS-K2601Terminal Description......................................................................................... 5

3.1.2 DS-K2602Terminal Description ......................................................................................... 7

3.1.3 DS-K2604 Terminal Description ...................................................................................... 10

Chapter 4 Card Reader Installation ......................................................................................... 14

4.1 External Terminal ............................................................................................................... 14

4.1.1 DS-K2601 External Terminals ......................................................................................... 14

4.1.2 DS-K2602 External Terminals ......................................................................................... 14

4.1.3 DS-K2604 External Terminals ......................................................................................... 14

4.2 Card Reader Installation ..................................................................................................... 15

4.2.1 The Connection of Wiegand Card Reader ...................................................................... 15

4.2.2 RS485 Card Reader Connection ..................................................................................... 16

4.3 Installing E-Lock .................................................................................................................. 17

4.3.1 Installation of Cathode Lock ........................................................................................... 17

4.3.2 Installation of Anode Lock .............................................................................................. 17

4.4 Connecting the External Alarm Device .............................................................................. 18

4.5 Door Button Wiring Diagram ............................................................................................. 18

4.6 The Connection of Magnetics Detection ........................................................................... 19

4.7 Connecting Power Supply .................................................................................................. 19

4.8 Arming Region Input Terminal ........................................................................................... 20

4.8.1 Connecting Normally Open Detector ............................................................................. 20

4.8.2 Connecting Normally Closed Detector ........................................................................... 20

4.9 Fire Alarm Module Wiring ................................................................................................. 21

Chapter 5 Settings ................................................................................................................. 22

5.1 Initializing the Hardware .................................................................................................... 22

5.2 Relay Input NO/NC ............................................................................................................. 22

5.2.1 Lock Relay Output .......................................................................................................... 22

5.2.2 Alarm Relay Output Status ............................................................................................. 23

Chapter 6 Activating the Access Control Terminal ................................................................... 25

Access Controller·User Manual

vii

6.1 Activating via SADP Software ............................................................................................. 25

6.2 Activating via Client Software ............................................................................................ 26

Chapter 7 Client Operation .................................................................................................... 29

7.1 Function Module ................................................................................................................ 29

7.2 User Registration and Login ............................................................................................... 29

7.3 System Configuration ......................................................................................................... 30

7.4 Access Control Management ............................................................................................. 31

7.4.1 Adding Access Control Device ........................................................................................ 32

7.4.2 Viewing Device Status .................................................................................................... 41

7.4.3 Editing Basic Information ............................................................................................... 41

7.4.4 Network Settings ............................................................................................................ 41

7.4.5 RS-485 Settings ............................................................................................................... 43

7.4.6 M1 Card Encryption ....................................................................................................... 44

7.4.7 Remote Configuration .................................................................................................... 45

7.5 Person and Card Management .......................................................................................... 52

7.5.1 Organization Management ............................................................................................ 52

7.5.2 Person Management ...................................................................................................... 53

7.6 Schedule and Template ...................................................................................................... 63

7.6.1 Week Schedule ............................................................................................................... 64

7.6.2 Holiday Group ................................................................................................................ 65

7.6.3 Template ......................................................................................................................... 66

7.7 Permission Configuration ................................................................................................... 68

7.7.1 Adding Permission .......................................................................................................... 69

7.7.2 Applying Permission ....................................................................................................... 70

7.8 Advanced Functions ........................................................................................................... 70

7.8.1 Access Control Parameters ............................................................................................. 71

7.8.2 Card Reader Authentication ........................................................................................... 73

7.8.3 Multiple Authentication ................................................................................................. 75

7.8.4 Open Door with First Card ............................................................................................. 78

7.8.5 Anti-Passing Back ........................................................................................................... 79

7.8.6 Cross-Controller Anti-passing Back ................................................................................ 80

7.8.7 Multi-door Interlocking .................................................................................................. 83

7.8.8 Authentication Password ............................................................................................... 84

7.8.9 Custom Wiegand ............................................................................................................ 85

7.9 Searching Access Control Event ......................................................................................... 87

7.10 Access Control Event Configuration ................................................................................... 88

Access Controller·User Manual

viii

7.10.1 Access Control Event Linkage ..................................................................................... 88

7.10.2 Access Control Alarm Input Linkage ........................................................................... 90

7.10.3 Event Card Linkage ..................................................................................................... 90

7.10.4 Cross-Device Linkage .................................................................................................. 92

7.11 Door Status Management .................................................................................................. 94

7.11.1 Access Control Group Management .......................................................................... 94

7.11.2 Anti-control the Access Control Point (Door) ............................................................. 95

7.11.3 Status Duration Configuration ................................................................................... 97

7.11.4 Real-time Card Swiping Record .................................................................................. 98

7.11.5 Real-time Access Control Alarm ................................................................................. 99

7.12 Arming Control ................................................................................................................. 100

Appendix A Sound Prompt and Indicator ................................................................................ 102

Appendix B Custom Wiegand Rule Descriptions ...................................................................... 103

Appendix C DIP Switch Description ......................................................................................... 105

Access Controller·User Manual

Chapter 1 Product Description

1.1 Overview

DS-K2600 is a powerful and stable access controller, using the logical architecture design. DS-K2600 is designed with TCP/IP network interface and its signal processed with special encryption and can be run offline. Anti-tampering function is also supported.

1.2 Main Features

 The access controller is equipped with 32-bit high-speed processor  Supports TCP/IP and GPRS network communication, Ehome accessing. The communication

data is specially encrypted to relieve the concern of privacy leak

 Support recognition and storage of card number with maximum length of 20  The access controller can store 100 thousand legal cards (97 thousand normal cards and 3

thousand visitor cards) and 300 thousand card swiping records

 Supports multi-door interlock function, anti-passback function, multi-card function, first card

open function, super card and super password function, M1 card encryption, online upgrade function and remote control of the doors

 Supports tamper-proof alarm for card reader, alarm for door not secured, force opening door

alarm, alarm for door opening timeout, duress card and code alarm, blacklist alarm and alarm for illegal card swiping attempts reaching the limit

 The alarm input of controller supports short circuit protection function and cut-proof function  Multiple event upload methods: channel, center group, and listening  50 event and card linkages  IP address conflict detection  Cross-controller anti-passing back function (For cross-controller anti-passing back based on

card, wire the card reader with RS-485. For cross-controller anti-passing back based on network, connect the server and device properly. Up to 5000 cards’ swiping records can be stored in the selected server.) and inner-device anti-pass-back function

 Supports RS485 interface and Wiegand interface for accessing card reader. RS485 interface

adopts dual-interface design and supports loop breakpoint detection and redundancy function; Wiegand interface supports W26, W34 and is seamlessly compatible with third-party card reader with Wiegand interface

 Supports various card types as normal/ disabled/ blacklist/ patrol/ guest/ duress/ super card,

etc.

 Various indicators to show different status  Supports time synchronization via NTP, manual or automatic method  Supports record storage function when it is offline and insufficient storage space storage alarm

function

Access Controller·User Manual

 The access controller has backup battery design, watchdog design and tamper-proof function  Data can be permanently saved after the access controller is powered off.  Supports I/O linkage, and event linkage  Supports Ehome protocol, and inter-network communication  500 groups of password under the authentication mode of card and password

Access Controller·User Manual

Chapter 2 Component Description

Take DS-K2604 as an example, the component schematic diagram is shown below.

No.

Component Description

DS-K2601

DS-K2602

DS-K2604

Alarm Relay Output Status (NC/NO)

Network Data Indicator

RS-485 Communication Indicator

Network Status Indicator

Door Relay Output Status (NC/NO) Choice

Battery Charging Indicator

Access Controller·User Manual

No.

Component Description

Power Indicator

Charging Completing Indicator

Running Indicator

Hardware Initialization and Normal Working Choice

Main board dial-up switch Set the DIP address for the access controller. Available Range: 1 to 63. Example: If the DIP address is 24, switch Bit 4 and Bit 5 to ON.

Notes:

 The settings will be valid after the device reboot.  For details about the DIP settings, see Appendix C

DIP Switch Description.

Access Controller·User Manual

Chapter 3 Terminal Connection

3.1 Terminal Description

3.1.1 DS-K2601Terminal Description

DS-K2601 Terminal descriptions are as follows:

No.

DS-K2601

Lock Power

GND

Grounding

+12V

Power Output of the Lock

Card Reader Power

GND

Grounding

+12V

Power Output of the Head Read

Wiegand Card Reader 2

GND

Grounding

Wiegand Head Read Data Input Data0

Wiegand Head Read Data Input Data1

Card Reader Buzzer Control Output

ERR

Indicator of Card Reader Control

Output (Invalid Card Output)

Access Controller·User Manual

No.

DS-K2601

A10

Indicator of Card Reader Control

Output (Valid Card Output)

A11

Wiegand Card Reader 1

GND

Grounding

A12

Wiegand Head Read Data Input Data0

A13

Wiegand Head Read Data Input Data1

A14

Card Reader Buzzer Control Output

A15

ERR

Indicator of Card Reader Control

Output (Invalid Card Output)

A16

Indicator of Card Reader Control

Output (Valid Card Output)

Arming Region Input

Arming Region Access Terminal 1

GND

Grounding

Arming Region Access Terminal 2

Arming Region Access Terminal 3

GND

Grounding

Arming Region Access Terminal 4

E-Lock

D1+

Door 1 Door Relay Input (Dry Contact)

D1-

Door Contact Input

Door 1 Door Contact Detector Input

B10

GND

Grounding

B11

Door Open Button

Door 1 Door Open Button Input

B12

GND

Grounding

Power

+12V

DC12V Cathode

GND

DC12V Grounding Input

Battery

BAT+

DC12V Battery Cathode

BAT-

DC12V Battery Anode

485 Card Reader

RS 485A+

Card Reader RS485+ Access

RS 485A-

Card Reader RS485- Access

GND

Grounding

RS 485B+

Card Reader RS485+

RS 485B-

Card Reader RS485-

C10

GND

Grounding

C11

Access Controller RS485

Interface

RS 485C+

Uplink RS485+Communication

C12

RS 485C-

Uplink RS485-Communication

C13

GND

Grounding

C14

RS 485D+

Reserved

C15

RS 485D-

C16

GND

C17

Alarm Output

NO/NC1

Alarm Relay 1 Output (Dry Contact)

C18

COM1

C19

NO/NC2

Alarm Relay 2 Output (Dry Contact)

C20

COM2

Event Input

Event Alarm Input 2

Access Controller·User Manual

No.

DS-K2601

GND

Grounding

Event Alarm Input 1

3.1.2 DS-K2602Terminal Description

DS-K2602 Terminal descriptions are as follows:

No.

DS-K2602

Power for E-Lock

GND

Grounding

+12V

Power Output of the Lock

Power for Card Reader

GND

Grounding

+12V

Power Output of the Head Read

Wiegand Card Reader

GND

Grounding

Wiegand Head Read Data Input Data0

Wiegand Head Read Data Input Data1

Card Reader Buzzer Control Output

ERR

Indicator of Card Reader Control Output (Invalid

Card Output)

A10

Indicator of Card Reader Control Output (Valid

Access Controller·User Manual

No.

DS-K2602

Card Output)

A11

Wiegand Card Reader

GND

Grounding

A12

Wiegand Head Read Data Input Data0

A13

Wiegand Head Read Data Input Data1

A14

Card Reader Buzzer Control Output

A15

ERR

Indicator of Card Reader Control Output (Invalid

Card Output)

A16

Indicator of Card Reader Control Output (Valid

Card Output)

A17

Wiegand Card Reader

GND

Grounding

A18

Wiegand Head Read Data Input Data0

A19

Wiegand Head Read Data Input Data1

A20

Card Reader Buzzer Control Output

A21

ERR

Indicator of Card Reader Control Output (Invalid

Card Output)

A22

Indicator of Card Reader Control Output (Valid

Card Output)

A23

Wiegand Card Reader

GND

Grounding

A24

Wiegand Head Read Data Input Data0

A25

Wiegand Head Read Data Input Data1

A26

Card Reader Buzzer Control Output

A27

ERR

Indicator of Card Reader Control Output (Invalid

Card Output)

A28

Indicator of Card Reader Control Output (Valid

Card Output)

Arming Region

Arming Region Access Terminal 1

GND

Grounding

Arming Region Access Terminal 2

Arming Region Access Terminal 3

GND

Grounding

Arming Region Access Terminal 4

E-Lock1

D1+

Door 1 Door Relay Input (Dry Contact)

D1-

E-Lock2

D2+

Door 2 Door Relay Input (Dry Contact)

B10

D2-

B11

Door Magnetics

Detector

Door 1 Magnetic Detector Input

B12

GND

Signal Grounding

B13

Door 2 Magnetic Detector Input

B14

Door Button

Door 1 Door Button Input

B15

GND

Signal Grounding

B16

Door 2 Door Button Input

Power

+12V

DC12V Cathode

GND

Grounding

Access Controller·User Manual

No.

DS-K2602

Battery

BAT+

DC12V Battery Cathode

BAT-

DC12V Battery Anode

Card Reader 485

Interface

485A+

Card Reader RS485+ Access

485A-

Card Reader RS485- Access

GND

Grounding

485B+

Card Reader RS485+

485B-

Card Reader RS485-

C10

GND

Grounding

C11

RS-485 Interface

485C+

Uplink RS485+Communication

C12

485C-

Uplink RS485-Communication

C13

GND

Grounding

C14

485D+

Reserved

C15

485D-

C16

GND

C17

Alarm Output

NO/N

Alarm Relay 1 Output (Dry Contact)

C18

COM1

C19

NO/N

Alarm Relay 2 Output (Dry Contact)

C20

COM2

C21

NO/N

Alarm Relay 3 Output (Dry Contact)

C22

COM3

C23

NO/N

Alarm Relay 4 Output (Dry Contact)

C24

COM4

Event Input

Event Alarm Input 4

GND

Grounding

Event Alarm Input3

Event Alarm Input 2

GND

Grounding

Event Alarm Input 1

Access Controller·User Manual

3.1.3 DS-K2604 Terminal Description

DS-K2604 Terminal descriptions are as follows:

No.

DS-K2604

Power Supply

of E-Lock

GND

Grounding

+12V

Power Supply of E-Lock Output

Power Supply

of Card Reader

GND

Grounding

+12V

Power Supply of Card Reader Output

Wiegand Card

Reader 4

GND

Grounding

Wiegand Card Reader Data Input Data0

Wiegand Card Reader Data Input Data1

Buzzer of Card Reader Control Output

ERR

Cresset of Card Reader Control Output (Invalid

Card Output)

A10

Cresset of Card Reader Control Output (Valid Card

Output)

A11

Wiegand Card

Reader 3

GND

Grounding

A12

Wiegand Card Reader Data Input Data0

A13

Wiegand Card Reader Data Input Data1

Access Controller·User Manual

No.

DS-K2604

A14

Buzzer of Card Reader Control Output

A15

ERR

Cresset of Card Reader Control Output (Invalid

Card Output)

A16

Cresset of Card Reader Control Output (Valid Card

Output)

A17

Wiegand Card

Reader 2

GND

Grounding

A18

Wiegand Card Reader Data Input Data0

A19

Wiegand Card Reader Data Input Data1

A20

Buzzer of Card Reader Control Output

A21

ERR

Cresset of Card Reader Control Output (Invalid

Card Output)

A22

Cresset of Card Reader Control Output (Valid Card

Output)

A23

Wiegand Card

Reader 1

GND

Grounding

A24

Wiegand Card Reader Data Input Data0

A25

Wiegand Card Reader Data Input Data1

A26

Buzzer of Card Reader Control Output

A27

ERR

Cresset of Card Reader Control Output (Invalid Card

Output)

A28

Cresset of Card Reader Control Output (Valid Card

Output)

Arming Region

Input

Arming Region Access Terminal 1

GND

Grounding

Arming Region Access Terminal 2

Arming Region Access Terminal 3

GND

Grounding

Arming Region Access Terminal 4

E-Lock 1

D1+

Door 1 Door Relay Input (Dry Contact)

D1-

E-Lock 2

D2+

Door 2 Door Relay Input (Dry Contact)

B10

D2-

B11

E-Lock 3

D3+

Door 3 Door Relay Input (Dry Contact)

B12

D3-

B13

E-Lock 4

D4+

Door 4 Door Relay Input (Dry Contact)

B14

D4-

B15

Door Magnetics

Input

Door 1 Magnetic Detector Input

B16

GND

Signal Grounding

B17

Door 2 Magnetic Detector Input

B18

Door 3 Magnetic Detector Input

Access Controller·User Manual

No.

DS-K2604

B19

GND

Signal Grounding

B20

Door 4 Magnetic Detector Input

B21

Door Button

Door 1 Door Button Input

B22

GND

Signal Grounding

B23

Door 2 Door Button Input

B24

Door 3 Door Button Input

B25

GND

Signal Grounding

B26

Door 4 Door Button Input

Power

+12V

DC12V Cathode

GND

Grounding

Battery

BAT+

DC12V Battery Cathode

BAT-

DC12V Battery Anode

Card Reader

RS485

RS 485A+

Card Reader RS485A+

RS 485A-

Card Reader RS485A-

GND

Grounding

RS 485B+

Card Reader RS485B+

RS 485B-

Card Reader RS485B-

C10

GND

Grounding

C11

Access

Controller

RS485

RS 485C+

Uplink RS485+Communication

C12

RS 485C-

Uplink RS485-Communication

C13

GND

Grounding

C14

RS 485D+

Reserved

C15

RS 485D-

C16

GND

C17

Alarm Output

NO/NC1

Alarm Relay 1 Output (Dry Contact)

C18

COM1

C19

NO/NC2

Alarm Relay 2 Output (Dry Contact)

C20

COM2

C21

NO/NC3

Alarm Relay 3 Output (Dry Contact)

C22

COM3

C23

NO/NC4

Alarm Relay 4 Output (Dry Contact)

C24

COM4

Event Input

Event Alarm Input 8

GND

Grounding

Event Alarm Input 7

Event Alarm Input 6

GND

Grounding

Event Alarm Input 5

Event Alarm Input 4

GND

Grounding

Event Alarm Input3

D10

Event Alarm Input 2

D11

GND

Grounding

Access Controller·User Manual

No.

DS-K2604

D12

Event Alarm Input 1

Notes:

 The Alarm input hardware interface is normally open by default. So only the normally open

signal is allowed. It can be linked to the buzzer of the card reader and access controller, and the alarm relay output and door relay open and close.

 Arming region alarm input linkage is only for the alarm relay output linkage.  RS485 card ID should be set as 1to 8. For example, the ID of door 1 is 1 and 2 standing for in

and out respectively.

 For single-door access controller, the Wiegand card reader 1 and 2 respectively correspond to

the entering and exiting card readers of door 1. For two-door access controller, the Wiegand card reader 1 and 2 respectively correspond to the entering and exiting card readers of door 1 , and the Wiegand card reader 3 and 4 respectively correspond to the entering and exiting card readers of door 2. For four-door access controller, the Wiegand card reader 1, 2, 3 and 4 respectively correspond to the entering card readers of door 1, 2, 3, and 4.