Henny Penny SCD-6, SCD-8 User Manual

Model SCD-6/8

SECTION 2. MAINTENANCE

2-1. INTRODUCTION This section provides procedures for the checkout and replacement

of the various parts used within the rotisserie. Before replacing any
parts, refer to the Troubleshooting Section. It will aid you in
determining the cause of the malfunction.

2-2. MAINTENANCE HINTS 1. Y ou may want to use a multimeter to check the electric

components.

2. When the manual refers to the circuit being closed, the
multimeter should read zero unless otherwise noted.

3. When the manual refers to the circuit being open, the multimeter
will read infinity .

2-3. LIGHT BULB
REPLACEMENT

Figure 2-1

Light bulbs and glass may be hot. Severe burns could
result.

1. Unscrew the lamp cover (Figure 2-1).

2. Unscrew and remove light bulb, and replace with a new
40 watt bulb - HP part number , BL01-014.

3. Replace lamp cover.

203 2-1

2-4. BLOWER REPLACEMENT 1. Remove electrical power supplied to the unit.

T o avoid electrical shock or pr operty damage, move the
power switch to OFF and disconnect main circuit
breaker , or unplug cord at wall receptacle.

2. Remove the side panel closest to the controls.

3. Cut the 3 wires to the blower motor (Figure 2-2).

Model SCD-6/8

Figure 2-2

Figure 2-3

Figure 2-4

4. Using a Phillips head screwdriver, remove the mounting
screws (Figure 2-3).

5. Cut seal around the plastic housing and pull blower from unit

(Figure 2-4).

6. Mount new blower, sealing the blower housing with high

temperature sealant.

7. Matching the wire colors, connect the wires of new blower with
those cut in step 3, using wire nuts or wire splicers.

8. Secure wires to keep out of components.

9. Replace side panel and restore electrical power .

2-2 203

2-5. THERMAL SENSOR 1. Remove electrical power supplied to the unit.

REPLACEMENT

T o avoid electrical shock or pr operty damage, move the

power switch to OFF and disconnect main circuit
breaker , or unplug cord at wall receptacle.

2. Remove the side panel closest to the controls.

3. Pull back insulation to expose sensor wires.

Model SCD-6/8

Figure 2-5 4. Using a Phillips head screwdriver, remove the mounting plate

screws and pull plate from unit (Figure 2-5).

5. Pull wire connector apart (Figure 2-6).

Figure 2-6

6. Using a flat-head screwdriver, pry the sensor from the plate
(Figure 2-7).

7. Snap a new sensor onto bracket and replace sensor in reverse
order, starting with step 5.

Figure 2-7

203 2-3

2-6. LIGHT FIXTURE 1. Remove electrical power supplied to the unit.

REPLACEMENT

T o avoid electrical shock or pr operty damage, move the
power switch to OFF and disconnect main circuit
breaker , or unplug cord at wall receptacle.

On stacked units, the top unit must be removed from the top of
the SCD to replace the light fixture. Remove the stacking
brackets shown in Figure 2-1, then lift the top unit off
of the SCD.

2. Remove the top cover of the SCD.

Model SCD-6/8

3. Remove the wires from the faulty light fixture (Figure 2-8).

Figure 2-8

4. Push in on the mounting tabs of the light socket, and remove the
light socket from the interior of the unit (Figure 2-9).

5. Snap new light fixture into place from the interior of the unit.

6. Replace top cap (and re-stack units where applicable), and
restore electrical power.

Figure 2-9

2-7. POWER SWITCH 1. Remove electrical power supplied to the unit.

T o avoid electrical shock or pr operty damage, move the
power switch to OFF and disconnect main circuit
breaker , or unplug cord at wall receptacle.

2. Remove the side panel closest to the controls.

2-4 203