HandHeld 4410, 4710 User Manual
IMAGETEAM™ 4410/4710
2D Series Hand Held Imager
™
User’s Guide
Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Class B Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio or television technician for help.
Caution: Any changes or modifications made to this device that are not
expressly approved by Hand Held Products, Inc. may void the user’s authority to
operate the equipment.
Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be shielded cables, in which the cable shield
wire(s) have been grounded (tied) to the connector shell.
Canadian Notice
This equipment does not exceed the Class B limits for radio noise emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant
les limites applicables aux appareils numeriques de la classe B prescrites dans
le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
LED Safety Statement
This device has been tested in accordance with EN60825-1 LED safety, and has
been certified to be under the limits of a Class 1 LED device.
The CE mark on the product indicates that the system has been tested
to and conforms with the provisions noted within the 89/336/EEC
Electromagnetic Compatibility Directive and the 73/23/EEC Low
Voltage Directive.
For further information please contact:
Hand Held Products, Inc.
Nijverheidsweg 9
5627 BT Eindhoven
The Netherlands
Hand Held Products shall not be liable for use of our product with equipment (i.e.,
power supplies, personal computers, etc.) that is not CE marked and does not
comply with the Low Voltage Directive.
Patents
Please refer to the product packaging for patent information.
Disclaimer
Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make
changes in specifications and other information contained in this document
without prior notice, and the reader should in all cases consult Hand Held
Products to determine whether any such changes have been made. The
information in this publication does not represent a commitment on the part of
Hand Held Products.
Hand Held Products shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages
resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of Hand
Held Products.
© 2005 Hand Held Products, Inc. All rights reserved.
Web Address: www.handheld.com
Table of Contents
Chapter 1 - Introduction and Installation
About the Hand-Held and Fixed Mount 2D Imager............. 1-1
Unpacking the Imager........................................................... 1-2
IT4410 Imager Identification................................................ 1-4
IT4710 Imager Identification................................................ 1-5
Connecting the Scanner in Keyboard Wedge Mode............. 1-6
Connecting the Scanner to a Serial Port...............................1-7
Reading Techniques.............................................................. 1-8
Chapter 2 - Programming
Introduction........................................................................... 2-1
Reset Factory Settings .......................................................... 2-2
Status Check ......................................................................... 2-2
All Symbologies ................................................................... 2-2
Revision Selections............................................................... 2-3
Terminal Interface ................................................................ 2-4
Supported Terminals Chart................................................... 2-5
Keyboard Country ................................................................ 2-6
Keyboard Style ..................................................................... 2-7
Keyboard Modifiers.............................................................. 2-8
Keyboard Function Relationships......................................... 2-9
Communication Settings..................................................... 2-10
Parity............................................................................ 2-10
Baud Rate..................................................................... 2-11
Word Length Data Bits ................................................ 2-12
Word Length Stop Bits................................................. 2-12
Hardware Flow Control................................................ 2-13
Software Flow Control................................................. 2-13
Serial Triggering .......................................................... 2-14
Trigger Timeout.................................................................. 2-15
Power Saving Mode............................................................ 2-16
Power Hold Mode............................................................... 2-17
LED Power Level............................................................... 2-17
LED Flashing...................................................................... 2-18
i
Aimer Delay........................................................................ 2-18
Aimer Interval..................................................................... 2-19
Centering............................................................................. 2-20
AutoTrigger ........................................................................ 2-23
Scan Stand .......................................................................... 2-23
Scan Stand Symbol ...................................................... 2-24
Presentation Mode.............................................................. 2-24
Presentation Re-trigger Delay...................................... 2-24
Presentation Lights....................................................... 2-25
Presentation Default..................................................... 2-25
Fast Omni Mode................................................................. 2-26
Beeper Volume................................................................... 2-26
Power Up Beeper................................................................ 2-27
Output Sequence Beeper..................................................... 2-27
Beep On Decode................................................................. 2-27
Beeper Default ............................................................. 2-27
Intercharacter, Interfunction,
and Intermessage Delays.................................................. 2-28
Intercharacter Delay .................................................... 2-28
User Specified Intercharacter Delay ........................... 2-28
Interfunction Delay ..................................................... 2-29
Intermessage Delay ..................................................... 2-30
Prefix/Suffix Overview....................................................... 2-31
Adding a Prefix or Suffix............................................. 2-32
Add a Carriage Return Suffix to All Symbologies ..... 2-33
Add a Code I.D. Prefix to All Symbologies ................ 2-33
Add an AIM I.D. Prefix to All Symbologies .............. 2-33
Prefix Entries................................................................ 2-34
Suffix Entries ............................................................... 2-34
Symbology Chart................................................................ 2-35
Decimal to Hex to ASCII Conversion Chart...................... 2-36
ii
Data Format Editor Overview............................................. 2-37
Format Editor Commands............................................2-38
Data Format Editor.......................................................2-40
Data Formatter.............................................................. 2-41
Require Data Format ....................................................2-41
Show Data Formats......................................................2-41
Alternate Data Formats ................................................2-42
Output Sequence Overview ................................................ 2-43
Require Output Sequence.............................................2-44
Output Sequence Editor................................................2-46
Multiple Symbols................................................................2-47
No Read ..............................................................................2-47
Print Weight........................................................................ 2-48
Function Code Transmit .....................................................2-48
Video Reverse.....................................................................2-49
Chapter 3 - Symbologies
Introduction...........................................................................3-1
Codabar................................................................................. 3-2
Start/Stop Characters......................................................3-2
Message Length.............................................................. 3-2
Check Character .............................................................3-3
Code 39.................................................................................3-4
Start/Stop Characters......................................................3-4
Message Length.............................................................. 3-5
Full ASCII......................................................................3-5
Check Character .............................................................3-6
Code 11.................................................................................3-7
Message Length.............................................................. 3-7
Check Digits Required ................................................... 3-8
Interleaved 2 of 5..................................................................3-9
Message Length.............................................................. 3-9
Check Digit...................................................................3-10
IATA 2 of 5......................................................................... 3-11
Message Length............................................................ 3-11
iii
MSI..................................................................................... 3-12
Message Length ........................................................... 3-12
Check Digit .................................................................. 3-13
Code 93............................................................................... 3-14
Message Length ........................................................... 3-14
Code 128............................................................................. 3-15
Message Length ........................................................... 3-15
ISBT.................................................................................... 3-16
EAN/JAN 8......................................................................... 3-17
Check Digit .................................................................. 3-17
EAN/JAN 8 Addenda................................................... 3-18
EAN/JAN 8 Addenda Required................................... 3-18
EAN/JAN 8 Addenda Separator .................................. 3-18
EAN/JAN 13....................................................................... 3-19
Check Digit .................................................................. 3-19
EAN/JAN 13 Addenda................................................. 3-20
EAN/JAN 13 Addenda Required................................. 3-20
EAN/JAN 13 Addenda Separator ................................ 3-20
UPC A................................................................................. 3-21
Check Digit .................................................................. 3-21
Number System............................................................ 3-21
UPC A Addenda........................................................... 3-22
UPC A Addenda Required........................................... 3-22
UPC A Addenda Separator .......................................... 3-22
UPC E0............................................................................... 3-23
Check Digit .................................................................. 3-23
Number System............................................................ 3-23
Version E Expand ........................................................ 3-24
UPC E1............................................................................... 3-24
UPC E0/E1 Addenda.................................................... 3-24
UPC E0/E1 Addenda Required.................................... 3-25
UPC E0/E1 Addenda Separator................................... 3-25
RSS-14................................................................................ 3-26
RSS-14 Limited.................................................................. 3-26
RSS-14 Expanded............................................................... 3-27
Message Length ........................................................... 3-27
iv
Codablock...........................................................................3-28
Message Length............................................................ 3-28
PDF417...............................................................................3-29
Message Length............................................................ 3-29
MicroPDF417 .....................................................................3-30
Message Length............................................................ 3-30
Code 49...............................................................................3-31
Message Length............................................................ 3-31
EAN•UCC Composite Codes ............................................. 3-32
Message Length............................................................ 3-32
TLC39................................................................................. 3-33
U.S. Postal Service POSTNET Code.................................. 3-34
Check Digit...................................................................3-34
Planet Code.........................................................................3-34
Check Digit...................................................................3-34
British Post Office 4 State Code ........................................3-35
Canadian 4 State Code........................................................ 3-35
Dutch Postal Code...............................................................3-35
Australian 4 State Code ......................................................3-35
Japanese Postal Service.......................................................3-35
QR Code..............................................................................3-36
Message Length............................................................ 3-36
Data Matrix.........................................................................3-37
Message Length............................................................ 3-37
MaxiCode............................................................................ 3-38
Message Length............................................................ 3-38
Structured Carrier Message Only................................. 3-39
Aztec Code..........................................................................3-40
Message Length............................................................ 3-40
Test Menu .......................................................................... 3-41
2D PQA (Print Quality Assessment) .................................. 3-41
Chapter 4 - OCR Programming
Introduction...........................................................................4-1
OCR ...................................................................................... 4-2
OCR Direction................................................................ 4-3
v
Creating OCR Templates...................................................... 4-4
Creating an OCR Template............................................ 4-4
Stringing Together Multiple Formats
(Creating “Or” Statements)............................................ 4-6
Creating a User-Defined Variable.................................. 4-6
Adding an OCR Check Character.................................. 4-7
OCR Template Codes .................................................... 4-9
Chapter 5 - Default Charts
Communication (RS-232) Selections............................. 5-1
Imager Selections........................................................... 5-1
Prefix/Suffix Selections................................................. 5-2
Data Formatter Selections.............................................. 5-2
Output Sequence Selections........................................... 5-2
Linear Symbologies ....................................................... 5-2
Postal Symbology Selections......................................... 5-4
2D Matrix Selections...................................................... 5-4
OCR Selections.............................................................. 5-5
Chapter 6 - Software Development Kit
Software Development Kit (SDK)........................................ 6-1
Features of the SDK.............................................................. 6-1
Chapter 7 - Quick*View
Quick*View Demonstration Software Instructions.............. 7-1
Setting Up the Imager and the Quick*View Software... 7-1
Installing Quick*View from the Web................................... 7-1
Using the Quick*View Software.......................................... 7-3
Load New Imager Software........................................... 7-8
Serial Programming Commands.................................... 7-9
Query Commands .............................................................. 7-11
Trigger Commands............................................................. 7-12
Serial Programming Commands ........................................ 7-14
vi
Imaging Commands ........................................................... 7-27
Image Commands Help File.........................................7-27
Image Ship.................................................................... 7-27
Image Capture/Ship and Image Get Commands..........7-28
Image Cropping/Shipping Example.............................7-29
Intelligent Signature Capture Commands .................... 7-29
Chapter 8 - Visual Menu
Visual Menu Introduction..................................................... 8-1
Installing Visual Menu from the Web............................8-2
Chapter 9 - Interface Keys
Chapter 10 - Product Specifications & Pinouts
Product Specifications - IT4410 ......................................... 10-1
Product Specifications - IT4710 ......................................... 10-2
Depth of Field Charts..........................................................10-4
Cable Pinouts......................................................................10-6
Connector Part Numbers..............................................10-7
IT4410 Dimensions............................................................. 10-8
IT4710 Dimensions............................................................. 10-9
Chapter 11 - Maintenance & Troubleshooting
Repairs ................................................................................ 11-1
Maintenance........................................................................11-1
Replacing the Interface Cable ...................................... 11-2
Troubleshooting..................................................................11-3
Chapter 12 - Customer Support
Product Service and Repair................................................. 12-1
Online Product Service and Repair Assistance............12-2
Technical Assistance........................................................... 12-2
Online Technical Assistance ........................................12-2
Limited Warranty................................................................12-2
vii
viii
1
Introduction and Installation
About the Hand-Held and Fixed Mount 2D Imager
The hand-held and fixed mount 2D Imager is an economical, durable solution for
a wide variety of data collection applications. The Imager features the following:
• A tough, ergonomic thermoplastic housing for comfort and durability.
• Omni-directional reading of a variety of printed symbols, including the most
popular linear and 2D matrix symbologies.
• RS-232, keyboard wedge, and laser emulation communication outputs.
• The ability to capture and download images to a PC for signature capture
software applications, and PC-based decoding.
• The ability to read OCR fonts.
About this Manual
This user’s guide provides installation instructions for the hand-held Imager. The
chapters contain the following information:
Chapter 1 Unpacking and installing the Imager
Chapter 2 Programming selections
Chapter 3 Symbology programming selections
Chapter 4 OCR programming
Chapter 5 Default settings
Chapter 6 Software Developers Kit
Chapter 7 Quick*View software information and serial programming
Chapter 8 Visual Menu software
Chapter 9 Interface Keys
Chapter 10 Product Specifications & Pinouts
Chapter 11 Maintenance and troubleshooting
Chapter 12 Customer support, service information, and warranty
commands
IMAGETEAM™ 4410/4710 User’s Guide 1 - 1
Unpacking the Imager
Open the carton. The shipping carton or container should contain:
IMAGETEAM 4410 Convenience Kit:
IMAGETEAM 4410 Hand
Held Imager
Cable
IMAGETEAM 4710 Convenience Kit:
IMAGETEAM 4710 Hand
Held/Fixed Mount Imager
Universal Power Supply
and Power Cable
Universal Power Supply
and Power Cable
Cable
1 - 2 IMAGETEAM™ 4410/4710 User’s Guide
• Check to make sure everything you ordered is present.
• Save the shipping container for later storage or shipping.
• Check for damage during shipment. Report damage immediately to the
carrier who delivered the carton.
IMAGETEAM™ 4410/4710 User’s Guide 1 - 3
IT4410 Imager Identification
Model # - 4410XX-XX
Manufactured - August 2002
Serial # = P-12-34567
S/W = 34567001/4410
Enlarged View of Label
Hand Held IT4410 Imager
Bottom View
1 - 4 IMAGETEAM™ 4410/4710 User’s Guide
IT4710 Imager Identification
Hand Held IT4710 Imager
Bottom View
ITEM # IT4710
DATE / SN:
S / W Rev:
Hand Held Products
Skaneateles Falls, NEW YORK
13153
IMAGETEAM™ 4410/4710 User’s Guide 1 - 5
Connecting the Scanner in Keyboard Wedge Mode
A scanner can be connected between the keyboard and PC as a “keyboard
wedge,” plugged into the serial port, or connected to a portable data terminal in
non decoded output mode.
Note: Note: The IMAGETEAM 4410 and 4710 scanners are factory
programmed for a keyboard wedge interface to an IBM PC AT with a USA
keyboard.
The following is an example of a keyboard wedge connection:
1. Turn off power to the terminal/computer.
2. Disconnect the keyboard cable from
the back of the terminal/computer.
Disconnect
3. Connect the
appropriate interface
cable to the scanner
and to the terminal/
computer. The
scanner will beep
twice.
4. Connect the power
supply (4 to 9V).
1
3
5. Turn the terminal/
computer power back
on.
6. Verify the scanner
operation by scanning
a bar code. The
scanner will beep
once.
The scanner is now connected and ready to communicate with your terminal/PC.
You must program the scanner for your interface before bar code data can be
transmitted to your terminal/PC. If you are using the scanner as a keyboard
wedge, see"Terminal Interface" on page 2-4. If the scanner is connected via a
serial port, turn to "Connecting the Scanner to a Serial Port" on page 1-7.
2
4
1 - 6 IMAGETEAM™ 4410/4710 User’s Guide
Connecting the Scanner to a Serial Port
Turn off power to the terminal/computer.
1. Connect the interface cable to the scanner
2. Connect the interface cable to the 4 to 9 volt power supply and plug in the
power supply. The scanner will beep twice.
3. Connect the interface cable to the terminal/computer.
2
Power Supply
3
Interface Cable
1
4. Turn the terminal/computer power back on.
5. Verify the scanner operation by scanning a bar code from the sample bar
code section in the back of this manual. The scanner will beep once.
The scanner is now connected and ready to communicate with your terminal/PC.
Turn to "Communication Settings" on page 2-10 to program the communication
parameters for a serial interface.
IMAGETEAM™ 4410/4710 User’s Guide 1 - 7
Reading Techniques
The hand-held Imager has a view finder that projects a bright red aiming beam
that corresponds to the Imager’s horizontal field of view. The aiming beam
should be centered over the bar code, but it can be positioned in any direction for
a good read.
Linear bar code 2D Matrix symbol
The aiming beam is smaller when the Imager is closer to the code and larger
when it is farther from the code. Symbologies with smaller bars or elements (mil
size) should be read closer to the unit. Symbologies with larger bars or elements
(mil size) should be read farther from the unit. (see "Depth of Field Charts" on
page 10-4.) To read single or multiple symbols (on a page or on an object), hold
the Imager at an appropriate distance from the target, pull the trigger, and center
the aiming beam on the symbol.
1 - 8 IMAGETEAM™ 4410/4710 User’s Guide
2
Programming
Introduction
Use this section to program the hand-held or fixed mount Imager.
This programming section contains the following menuing selections:
• General Selections
• Terminal Interface Selections
• Keyboard Selections
• Communication Settings
• Imager Selections
• Output Selections
• Prefix/Suffix Selections
• Data Formatter Selections
• Output Sequence Selections
IMAGETEAM™ 4410/4710 User’s Guide 2 - 1
Reset Factory Settings
All operating parameters are stored in nonvolatile memory resident in the
Imager, where they are permanently retained in the event of a power interruption.
When you receive your Imager, certain operating parameters have already been
set. These are the factory defaults, indicated by the symbol “✱” on the
programming menu pages (beneath the default programming symbol). Default
charts begin on page 5-1.
Default
Status Check
Read the
level to the host terminal. The software revision will be printed out as
“REV_SW:$ProjectRevision:1.xx$;REV_WA:31204960-xxx.”
Read the
Editor formats. One format per line will be printed out.
Show Software
Show Software Revision
Show Data Formats
Revision
symbol to transmit the software revision
symbol to transmit the existing Data Format
Show Data Formats
All Symbologies
If you want to decode all the symbologies allowable for your scanner, scan the
All Symbologies On
All Symbologies
On
code.
All Symbologies
Off
2 - 2 IMAGETEAM™ 4410/4710 User’s Guide
Revision Selections
Both the following programming codes would not normally be needed unless you
have a problem with the unit. An Application Support Representative may
request the boot code or power PC revision information in order to trouble shoot
a problem.
Boot Code RevisionPower PC Revision
IMAGETEAM™ 4410/4710 User’s Guide 2 - 3
Terminal Interface
IMAGETEAM 4410 and IMAGETEAM 4710 scanners are factory programmed
for a keyboard wedge interface to an IBM PC AT with a USA keyboard. If this is
your interface and you do not need to modify the settings, skip to "Power Saving
Mode" on page 2-16 to begin programming the scanner.
If your interface is not a standard PC AT, refer to the "Supported Terminals
Chart" on page 2-5 and locate the Terminal ID number for your PC. Scan the
Terminal ID bar code below, then scan the numeric bar code(s) on the inside
back cover of this manual to program the scanner for your terminal ID> Scan
Save to save your selection.
For example, an IBM PS/2 terminal has a Terminal ID of 002. You would scan
the Terminal ID bar code, then 0, 0, 2 from the inside back cover, then Save. If
you make an error while scanning the digits (before scanning Save), scan the
Discard code on the back cover and scan the digits and the Save code again.
Note: Factory Default for Keyboard Wedge units = 003
Note: Factory Default for True RS-232 units = 000
Terminal ID Save
2 - 4 IMAGETEAM™ 4410/4710 User’s Guide
Supported Terminals Chart
Terminal Model(s)
DEC PC433 SE (Portable PC) 003
DELL Latitude (Portable PC) 003
DTK 486 SLC (Portable PC) 003
Fujitsu Stylistic (Portable PC) 003
HHLC (Code 128 Emulation) 089
IBM PC XT 001
IBM PS/2 25, 30, 77DX2 002
IBM
IBM
IBM
IBM
IBM AT Thinkpad 106
Midwest Micro Elite TS 30 PS (Portable PC) 003
Mitak 4022 (Portable PC) 003
Olivetti M19, M24, M28, M200 001
Olivetti M240, M250, M290, M380, P500 003
Reliasys TR 175 003
RS-232 TTL 000
Televideo 990, 995, 9060 002
Texas Instruments Extensa 560CD (Portable PC) 003
Toshiba 2600 (Portable PC) 003
Toshiba Satellite T1960, T2130, CS (Portable PC) 003
Zenith Z-note (Portable PC) 003
AT, PS/2 30-286, 50, 55SX, 60, 70,
70-061, 70-121, 80
AT Compatibles Keyboard Emulation
(Non-wedge)
Thinkpad 360 CSE, 34, 750
(Portable PC)
Thinkpad 365, 755 CV
(Portable PC)
Terminal
I.D.
003
003
097
003
IMAGETEAM™ 4410/4710 User’s Guide 2 - 5
Keyboard Country
Scan the Program Keyboard Country bar code below, then scan the numeric
bar code(s) from the inside back cover, then the Save bar code to program the
keyboard for your country. As a general rule, the following characters are not
supported by the scanner for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
Keyboard Country
Country Code Scan Country Code Scan
Belgium..................... 1 Latin America.........14
Czechoslovakia ........ 15 Norway...................9
Denmark................... 8 Poland....................20
Finland......................2 Portugal .................13
France ...................... 3 Romania ................25
French Canadian...... 18 Russia....................26
Germany/Austria....... 4 Slovakia .................22
Great Britain ............. 7 Spain......................10
Greece......................17 Sweden..................23
Netherlands.............. 11 Switzerland ............6
Hungary.................... 19 Turkey Q ................24
Israel.........................12 Turkey F.................27
Italy........................... 5 USA
(Default)
.........0
Save
2 - 6 IMAGETEAM™ 4410/4710 User’s Guide
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock.
Regular.
Regular
Caps Lock
Shift Lock
to U.S. keyboards.)
Automatic Caps Lock
software tracks and reflects if you have Caps Lock on or off (AT and PS/2 only).
This selection can only be used with systems that have an LED which notes the
Caps Lock status.
is used when you normally have the Caps Lock key off.
is used when you normally have the Caps Lock key on.
is used when you normally have the Shift Lock key on. (Not common
is used if you change the Caps Lock key on and off. The
* Regular
Shift Lock
Default =
Caps Lock
Automatic
Caps Lock
Emulate External Keyboard
keyboard (IBM AT or equivalent). To connect to a laptop, you must scan the
Emulate External Keyboard bar code below, then scan "Automatic Direct
Connect Mode On" on page 2-8. After scanning these codes, you must re-boot
your laptop.
should be scanned if you do not have an external
Emulate External
Keyboard
IMAGETEAM™ 4410/4710 User’s Guide 2 - 7
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo
Mode.
Control + ASCII Mode On
control characters for values 00-1F. Refer to "Keyboard Function
Relationships" on page 2-9 for CTRL+ ASCII Values.
- The scanner sends key combinations for ASCII
Default = Off
Control + ASCII
Mode On
Turbo Mode
use with IBM AT only.) If the terminal drops characters, do not use Turbo Mode.
Default = Off
Turbo Mode On
Numeric Keypad Mode
numeric keypad.
Numeric Keypad
Mode On
Automatic Direct Connect
keyboard is disabled when you plug in the scanner. This selection can also be
used if you have an IBM AT style terminal and the system is dropping characters.
After scanning these codes, you must re-boot your computer.
- The scanner sends characters to an IBM AT terminal faster. (For
- Sends numeric characters as if entered from a
Default = Off
- Use this selection if you are using a laptop whose
* Control + ASCII
Mode Off
* Turbo Mode Off
* Numeric
Keypad Mode Off
Default = Off
Automatic Direct
Connect Mode On
* Automatic Direct
Connect Mode Off
2 - 8 IMAGETEAM™ 4410/4710 User’s Guide
Keyboard Function Relationships
The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII
“CTRL”+ relationships apply to all terminals that can be used with the scanner.
Function Code HEX/ASCII Value Full ASCII “CTRL” +
NUL 00 2
SOH 01 A
STX 02 B
ETX 03 C
EOT 04 D
ENQ 05 E
ACK 06 F
BEL 07 G
BS 08 H
HT 09 I
LF 0A J
VT 0B K
FF 0C L
CR 0D M
SO 0E N
SI 0F O
DLE 10 P
DC1 11 Q
DC2 12 R
DC3 13 S
DC4 14 T
NAK 15 U
SYN 16 V
ETB 17 W
CAN 18 X
EM 19 Y
SUB 1A Z
ESC 1B [
FS 1C \
GS 1D ]
RS 1E 6
US 1F -
IMAGETEAM™ 4410/4710 User’s Guide 2 - 9
Communication Settings
<Default All RS-232 Communication Settings>
Parity
Parity provides a means of checking character bit patterns for validity. The
Imager can be configured to operate under
None
) parity options. The host terminal must be set up for the same parity as
(
the Imager, to ensure reliable communication.
Mark, Space, Odd, Even
SpaceMark
, or No
Odd
* None
Even
2 - 10 IMAGETEAM™ 4410/4710 User’s Guide
Loading...