SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
AMS12H03
AMS18H03
AMS22H03
HSU-09CG13-B
HSU-12CG13-B
HSU-18CG13-B
HSU-24CG13-B
Please read this operation manual before using the air conditioner.
0010518054
Cautions
The machine is adaptive in following situation
I. Applicable ambient temperature range:
|
Indoor |
Maximum: D.B / W.B |
32oC/23oC |
|
|
Minimum: D.B / W.B |
18oC/14oC |
||
Cooling |
|
|||
Outdoor |
Maximum: D.B |
43oC/26oC |
||
|
||||
|
Minimum: D.B |
18oC |
||
|
Indoor |
Maximum: D.B |
27oC |
|
Heating |
Minimum: D.B |
15oC |
||
|
||||
Outdoor |
Maximum: D.B / W.B |
24oC/18oC |
||
|
||||
|
Minimum: D.B / W.B |
-7oC/-8oC |
||
|
|
2.If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F
3.If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.
4.The distance between the indoor unit and the floor should be more than 2m.
5.The wiring method should be in line with the local wiring standard.
6.After installation, the power plug should be easily reached.
7.The waste battery should be disposed properly.
8.The appliance is not intended to use by young children or infirm persons without supervision. 9.Young children should be supervised ensure that they do not play with the appliance.
10.The appliance must be installed on strong enough supporter. 11.The wiring diagram is attached inside the machine.
1
Parts and Functions
Indoor Unit
Inlet grille
Air filter
Test running switch(manual)
Used only for test running in cooling when room temp. is below 16oC. Don't use it in normal operation.
Emergency switch(manual)
Used when remote controller is lost or defective. Unit will run temporarily.
Remote signal receiver
A beeping sound is generated when a signal from remote controller is received.
Horizontal flap
Use remote controller to adjust up and down air flow. (Don't adjust it manually.)
Power indicator |
Timer mode indicator |
|
Lights up when unit starts. |
Lights up when Timer operation |
|
is selected. |
||
|
Operation mode indicator
Lights up during compressor running.
Actual inlet grille may vary from the one shown in the manual according to the product purchased
Outdoor Unit
AMS12H03
OUTLET
INLET
HSU-09CG13-B |
|
|
HSU-12CG13-B |
HSU-24CG13-B |
|
HSU-18CG13-B |
||
AMS22H03 |
||
AMS18H03 |
||
|
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
2
Parts and Functions
Operation Buttons and display of the remote controller.
1 |
|
|
|
5 |
|
|
|
|
|
2 |
|
|
|
6 |
U |
ON |
OFF |
7 |
|
3 |
O |
oC PM |
|
|
|
A |
AM |
|
|
|
T |
|
8 |
|
|
|
|
|
|
4 |
|
|
|
9 |
|
|
|
10 |
|
|
ON/OFF |
TEMP |
|
|
|
|
|
11
18
MODE |
SET |
12 |
19 |
FAN |
TIMER |
13 |
20 |
14 |
CLOCK |
SWING |
|
15 |
21 |
|
|
SLEEP |
|
16 |
|
LOCK |
RESET |
17 |
22 |
1.Mode display
AUTO COOL
DRY
|
HEAT |
|
FAN |
2. |
SWING display |
3. |
FAN SPEED display AUTO LO MED HI |
4.SLEEP display
5.LOCK display
6.SIGNAL SENDING
7.TIMER OFF display
8.TIMER ON display
9.CLOCK display
10.TEMP display
11.POWER ON/OFF
Used for unit start and stop.
12.MODE
Used to select AUTO run, COOL, DRY, HEAT and FAN operation
13.FAN
Used to select fan speed LO, MED, HI, AUTO
14.HOUR
Used to set clock and timer setting.
15.SWING
Used to set auto fan direction.
16.SLEEP
Used to select sleep mode.
17.LOCK
Used to lock buttons and LCD display.
18.TEMP.
Used to select your desired temp.
19.SET
Used to confirm timer and clock settings.
20.TIMER
Clock set
Used to select TIMER ON, TIMER OFF, TIMER ON-OFF
21.CLOCK
Used to set correct time
22.RESET
Used to reset the controller back to normal condition.
When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows:
Press CLOCK button, "AM" or "PM" flashes.
Pressor
to set correct time. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly.
After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working.
NOTE: Cooling only unit do not have displays and functions related with heating
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal.
3
Parts and Functions
Operation Buttons and display of the remote controller.
If the unit which you purchased has healthy function, Remote controller should
like the following figure:
1 |
|
|
|
5 |
|
|
|
|
|
2 |
|
|
|
6 |
A |
ON |
OFF |
7 |
|
3 |
U |
|||
O |
oC PM |
|
|
|
|
T |
AM |
|
|
|
|
|
|
8 |
4 |
|
|
|
9 |
|
|
|
10 |
|
|
ON/OFF |
TEMP |
|
|
|
|
|
11
18
MODE |
SET |
12 |
19 |
FAN |
TIMER |
13 |
20 |
14 |
|
SWING |
CLOCK |
15 |
21 |
SLEEP |
HEALTH |
16 |
|
LOCK |
RESET |
17 |
22 |
BRIEF INTRODUCTION TO HEALTH OPERATION
1. Mode display
AUTO
COOL
DRY
HEAT
FAN
2. SWING display
3. FAN SPEED display
4.SLEEP display
5.LOCK display
6.SIGNAL SENDING
7.TIMER OFF display
8.TIMER ON display
9.CLOCK display
10.TEMP display
11.POWER ON/OFF
Used for unit start and stop.
12.MODE
Used to select AUTO run, COOL,
DRY, HEAT and FAN operation
13.FAN
Used to select fan speed LO, MED, HI, AUTO
14.HOUR
Used to set clock and timer setting.
15.SWING
Used to set auto fan direction.
16.SLEEP
Used to select sleep mode.
17.LOCK
Used to lock buttons and LCD display.
18.TEMP.
Used to select your desired temp.
19.SET
Used to confirm timer and clock settings.
20.TIMER
Used to select TIMER ON, TIMER OFF, TIMER ON-OFF
21.CLOCK
Used to set correct time
22.RESET
Used to reset the controller back to normal condition.
23.HEALTH
Used to set healthy operation
The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.
NOTE: Cooling only unit do not have displays and functions related with heating
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal.
4
Operation
Remote controller's operation
When in use, put the signal transmission head directly to the receiver hole on the indoor unit.
The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.
Don't throw the controller, prevent it from being damaged.
When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder)
Remove the battery cover:
Slightly press " " and push down the cover.
Load the battery:
Be sure that the loading is in line with the" + "/"-" pole request as illustrated.
Put on the cover again Confirmation indicator:
In disorderation, reload the batteries or load the new batteries after 6mins.
Note:
Use two new same-typed batteries when loading.
If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key.
Hint:
Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key.
Power failure resume(please set and apply as necessary)
If sudden power failure occurs, the unit will resume original operation when power is supplied again.
Note: When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatically resume operation when power is re-supplied, or press ON/OFF to turn off the unit when power resumes.
5