Groen TDB/7 (CE) Operation Manual

IMPORTANT INFORMATION - KEEP FOR OPERATOR - IMPORTANT INFORMATION-

OPERATOR AND SERVICE MANUAL OM/SM-TDB/7(CE)

Part Number 128433 INTERNATIONAL

MODEL: TDB/7 (CE)

Steam Jacketed Kettle

Self-Contained
Electric heated
Table top mounted
Stainless Steel
Tilting

Crank Tilt Model

Pull Tilt Model

THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ, UNDERSTAND
AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS MANUAL.

FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS
IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

Information contained in this document is
known to be current and accurate at the time
of printing/creation. Unified Brands recom­mends referencing our product line websites,
unifiedbrands.net, for the most updated
product information and specifications.

OM/SM-TDB/7(CE)

IMPORTANT — READ FIRST — IMPORTANT

THESE APPLIANCES MUST BE INSTALLED BY A COMPETENT PERSON IN CONFORMITY WITH THE
INSTALLATION AND SERVICING INSTRUCTIONS AND NATIONAL REGULATIONS IN FORCE AT THE TIME.
PARTICULAR ATTENTION MUST BE PAID TO THE FOLLOWING:

I. E. E. REGULATIONS FOR ELECTRICAL INSTALLATIONS
ELECTRICITY AT WORK REGULATIONS
HEALTH AND SAFETY AT WORK ACT
FIRE PRECAUTIONS ACT
LOCAL AND NATIONAL BUILDING REGULATIONS

USERS SHOULD BE CONVERSANT WITH APPROPRIATE PROVISIONS OF THE FIRE PRECAUTIONS ACT.
IN PARTICULAR THEY SHOULD BE AWARE OF THE NEED FOR REGULAR SERVICING BY A COMPETENT
PERSON TO ENSURE CONTINUED SAFE AND EFFICIENT APPLIANCE PERFORMANCE.

WARNING: TO PREVENT SHOCKS, APPLIANCES WHETHER GAS OR ELECTRIC, MUST BE EARTHED.
UPON COMPLETION OF INSTALLATION, THE OWNERS MANUAL SHOULD BE HANDED TO USERS AND

THE INSTALLER SHOULD INSTRUCT RESPONSIBLE PERSON(S) IN THE CORRECT OPERATION AND
MAINTENANCE OF THE APPLIANCE.

THIS EQUIPMENT IS ONLY FOR PROFESSIONAL USE, AND SHALL BE OPERATED BY QUALIFIED
PERSONS. IT IS THE RESPONSIBILITY OF THE SUPERVISOR OR EQUIVALENT TO ENSURE THAT USERS
WEAR PROTECTIVE CLOTHING, AND TO DRAW ATTENTION TO THE FACT THAT, SOME PARTS WILL,
BY NECESSITY, BECOME VERY HOT AND WILL CAUSE BURNS IF TOUCHED ACCIDENTALLY.

UNLESS OTHERWISE STATED, PARTS WHICH HAVE BEEN PROTECTED BY THE MANUFACTURER ARE
NOT TO BE ADJUSTED BY THE INSTALLER.

BEFORE ATTEMPTING ANY SERVICING, ENSURE THAT THE ELECTRICAL SUPPLY IS DISCONNECTED.
WARNING: THE UNIT MUST BE INSTALLED BY PERSONNEL QUALIFIED TO WORK WITH

ELECTRICITY. IMPROPER INSTALLATION CAN RESULT IN INJURY TO PERSONNEL
AND/OR DAMAGE TO EQUIPMENT. THE UNIT MUST BE INSTALLED IN ACCORDANCE

WITH APPLICABLE CODES.
CAUTION: SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT.
WARNING: TO AVOID DAMAGE OR INJURY, FOLLOW THE WIRING DIAGRAM EXACTLY WHEN

CONNECTING A UNIT.
WARNING: BEFORE CLEANING THE OUTSIDE OF THE KETTLE, DISCONNECT ELECTRIC POWER .

KEEP WATER AND SOLUTIONS OUT OF CONTROLS AND ELECTRICAL COMPONENTS.
NOTICE: DO NOT USE ANY DE-GREASER THAT CONTAINS POTASSIUM HYDROXIDE OR SODIUM

HYDROXIDE OR THAT IS ALKALINE.
WARNING: USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY GROEN OR

THEIR AUTHORIZED DISTRIBUTOR VOIDS ALL WARRANTIES AND CAN RESULT IN

BODILY INJURY TO THE OPERATOR AND DAMAGE THE EQUIPMENT. SERVICE BY

OTHER THAN FACTORY-AUTHORIZED PERSONNEL WILL VOID ALL WARRANTIES.
WARNING: HIGH VOLTAGE EXISTS INSIDE CONTROL COMPARTMENTS. DISCONNECT FROM

BRANCH BEFORE SERVICING. FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY OR

DEATH.
CAUTION: BE SURE ALL OPERATORS READ, UNDERSTAND AND FOLLOW THE OPERATING

INSTRUCTIONS, CAUTIONS, AND SAFETY INSTRUCTIONS CONTAINED IN THIS MANUAL.
WARNING: THIS UNIT IS INTENDED FOR USE IN THE COMMERCIAL HEATING, COOKING AND

HOLDING OF WATER AND FOOD PRODUCTS, PER THE INSTRUCTIONS CONTAINED IN

THIS MANUAL. ANY OTHER USE COULD RESULT IN SERIOUS PERSONAL INJURY OR

DAMAGE TO THE EQUIPMENT AND WILL VOID WARRANTY.

2

OM/SM-TDB/7(CE)

WARNING: AVOID ALL DIRECT CONTACT WITH HOT EQUIPMENT SURFACES. DIRECT SKIN

CONTACT COULD RESULT IN SEVERE BURNS.
WARNING: AVOID ALL DIRECT CONTACT WITH HOT FOOD OR WATER IN THE KETTLE. DIRECT

CONTACT COULD RESULT IN SEVERE BURNS.
CAUTION: DO NOT OVER FILL THE KETTLE WHEN COOKING, HOLDING OR CLEANING. KEEP

LIQUIDS A MINIMUM OF 2-3” (5-8 cm) BELOW THE KETTLE BODY RIM TO ALLOW

CLEARANCE FOR STIRRING, BOILING AND SAFE PRODUCT TRANSFER.
WARNING: TAKE SPECIAL CARE TO AVOID CONTACT WITH HOT KETTLE BODY OR HOT PRODUCT

WHEN ADDING INGREDIENTS, STIRRING OR TRANSFERRING PRODUCT TO ANOTHER

CONTAINER.
WARNING: WHEN TILTING KETTLE FOR PRODUCT TRANSFER:

1) WEAR PROTECTIVE OVEN MITT AND PROTECTIVE APRON.

2) USE CONTAINER DEEP ENOUGH TO CONTAIN AND MINIMIZE PRODUCT SPLASHING.

3) PLACE CONTAINER ON STABLE, FLAT SURFACE, AS CLOSE TO KETTLE AS
POSSIBLE.

4) STAND TO LEFT OR RIGHT SIDE OF KETTLE WHILE POURING. DO NOT STAND
DIRECTLY IN POUR PATH OF HOT CONTENTS.

5) POUR SLOWLY, MAINTAIN CONTROL OF KETTLE, AND RETURN KETTLE BODY TO
UPRIGHT POSITION AFTER CONTAINER IS FILLED OR TRANSFER IS COMPLETE.

6) DO NOT OVER-FILL CONTAINER. AVOID DIRECT SKIN CONTACT WITH HOT
CONTAINER AND ITS CONTENTS.

CAUTION: KEEP FLOORS IN FRONT OF KETTLE WORK AREA CLEAN AND DRY. IF SPILLS OCCUR,

CLEAN IMMEDIATELY, TO AVOID SLIPS OR FALLS.

WARNING: FAILURE TO CHECK SAFETY VALVE OPERATION PERIODICALLY COULD RESULT IN

PERSONAL INJURY AND/OR DAMAGE TO EQUIPMENT.

WARNING: WHEN TESTING, AVOID ANY EXPOSURE TO THE STEAM BLOWING OUT OF THE SAFETY

VALVE. DIRECT CONTACT COULD RESULT IN SEVERE BURNS.

WARNING: BEFORE REPLACING ANY PARTS, DISCONNECT THE UNIT FROM THE ELECTRIC POWER

SUPPLY.

WARNING: KEEP WATER AND SOLUTIONS OUT OF CONTROLS AND ELECTRICAL EQUIPMENT.

NEVER SPRAY OR HOSE THE SUPPORT HOUSING OR ELECTRICAL CONNECTIONS.

3

OM/SM-TDB/7(CE)

Table of Contents

IMPORTANT OPERATOR WARNINGS .........................................................2

EQUIPMENT DESCRIPTION .................................................................5

INSPECTION & UNPACKING .................................................................7

INSTALLATION ............................................................................8

INITIAL START-UP .........................................................................9

OPERATION .............................................................................10

SEQUENCE OF OPERATION ................................................................12

MAINTENANCE ..........................................................................13

TROUBLESHOOTING ......................................................................15

CLEANING ...............................................................................19

PARTS LISTS ............................................................................21

SCHEMATICS ............................................................................25

SERVICE LOG ............................................................................26

REFERENCES ............................................................................26

WARRANTY ..............................................................................27

4

Equipment Description

OM/SM-TDB/7(CE)

The Groen TDB/7 is a table top, tilting, steam
jacketed kettle with a thermostatically controlled,
self-contained, electrically-heated steam supply and
appropriate controls, mounted on a sturdy base. The
Model TDB/7 is available in 20 or 40 - quart capacity.

The body of the TDB/7 Kettle is constructed of
stainless steel, welded into one solid piece. The
kettle is furnished with a reinforced rim and a
butterfly shaped pouring lip. It has a steam jacket
rated for pressures up to 50 PSIG. Kettle finish is
180 emery grit on the inside and bright semi-deluxe
on the outside. A tilt handle allows the operator to
manually tilt the kettle body in a controlled manner. A
crank tilt model is also available. Pouring height
accepts pans up to 4 inches high on a table top.

A built-in steam generator, sized for the kettle
capacity and heated by electricity, delivers steam
into the jacket. “Airless” operation of the steam
jacket permits uniform, efficient heating at
temperatures as low as 150°F and as high as 295°F.
In addition to the adjustable thermostat for operating
control, the unit has a tilt cut-off switch, low water
cut-off, safety valve, and high-limit pressure switch
as safety features. A heating indicator light,
pressure gauge, and sight glass are provided for
monitoring kettle operation.

A single electrical connection is required for
installation. The unit may be ordered for use with 230
Volt single phase or 400 Volt three phase power.

KETTLE CHARACTERISTICS

TDB/7-20+ TDB/7-40
Kettle Capacity 20 qts. 18.8 liters 40 qts. 37.6 liters
Jacket Capacity 4 qts. 3.7 liters 5 qts. 4.7 liters
Diameter 14” 36 cm 16-1/2” 42 cm
Depth 11” 28 cm 14-1/4” 36 cm
Base Width 24” 60 cm 24” 60 cm
Base Depth 16” 41 cm 16” 41 cm
KW at 230 Volt Single Phase 7.8 13.3
KW at 400 Volt Three Phase 7.8 13.3
Rated Amp Load - 1M 33 57
Rated Amp Load - 3M 11 (L1, L2, L3) 19 (L1, L2, L3)

5

OM/SM-TDB/7(CE)

Models

Pull Tilt TDB/7, CE Model

Crank Tilt TDB/7, CE Model

Optional equipment available with any model:

1. Stand that supports the unit and holds a pan in position for filling

2. Lift-off cover

3. Basket insert

4. Fill faucet

5. Manual stirrers (factory installed)

6. Motor driven agitator (factory installed)

6

Inspection & Unpacking

OM/SM-TDB/7(CE)

The unit will arrive in a heavy shipping carton and will
be attached to a skid. Immediately upon receipt,
inspect the carton carefully for exterior damage.

CAUTION
SHIPPING STRAPS ARE UNDER TENSION
AND CAN SNAP BACK WHEN CUT. TAKE
CARE TO AVOID PERSONAL INJURY OR
DAMAGE TO THE UNIT BY STAPLES LEFT
IN THE WALLS OF THE CARTON.

Carefully cut the polyester straps around the carton
and detach the sides of the box from the skid. Pull
the carton up off the unit.

Thoroughly inspect the unit for concealed damage.
Report any shipping damage or incorrect shipments
to the delivery agent.

Write down the model number, serial number, and
installation date, and retain this information

for future reference. Space for these entries is
provided at the top of the Service Log at the back of
this manual. Keep this manual on file and available
for operators to use.

CAUTION
THIS UNIT WEIGHS 140 TO 163 LB. (64 TO
74 KG). INSTALLER SHOULD OBTAIN
HELP AS NEEDED TO LIFT THIS WEIGHT
SAFELY.

When installation is to begin, carefully cut the straps
which hold the unit on the skid. Lift the unit straight
up off the skid. Examine packing materials to be
sure loose parts are not discarded with the materials.

Attach the tilt handle (normally shipped inside the
kettle) by carefully threading it into the socket on the
trunnion support. Be careful to avoid cross-threading
fine socket threads. This step is unnecessary if the
kettle is a crank tilt model.

The TDB/7 is shipped from the factory strapped on a
pallet. If the unit is a pull tilt model, the handle is packed
inside the kettle for shipment.

7

OM/SM-TDB/7(CE)

Installation

The Groen Kettle is provided with
complete internal wiring. It is ready for
immediate connection. A wiring diagram
is provided in this manual and on the
inside of the control housing service
panel. Any mechanical or electrical changes must be
approved by Groen’s Food Service Engineering
Department.

WARNING
INSTALLATION OF THE KETTLE MUST BE
DONE BY PERSONNEL QUALIFIED TO
WORK WITH ELECTRICITY. IMPROPER
INSTALLATION CAN RESULT IN INJURY
TO PERSONNEL AND/OR DAMAGE TO
EQUIPMENT.

The completed unit has been operated at the factory
to test all controls and heater elements.

1. Set the kettle in place and level it. The base
should be securely fastened to a table or work
surface. Four 3/8”-16 N.C. threaded couplings
are provided in the base of unit. Installation
under a ventilation hood is recommended.

2. Provide electrical power as specified on the
electrical information plate attached to the
equipment. Observe all local and national
codes, and all regulations in force at the time
of installation.

3. The equipment is shipped ready for three
phase operation. Refer to the wiring diagram
for single phase operation.

4. Bring the electrical service through the
entrance at the rear of the support housing,
making a watertight connection with the
incoming lines. (A BX connection is not
recommended.) Observe all local and
national codes, and all regulations in force at
the time of installation.

DANGER
ELECTRICALLY GROUND THE UNIT AT
THE TERMINAL PROVIDED. FAILURE TO
GROUND UNIT COULD RESULT IN
ELECTROCUTION AND DEATH.

5. Confirm that the jacket water level is above
mid point of sight glass. If the level is low,
follow the instructions under “Jacket Filling
and Water Treatment,” Page 14.

6. Electrically earth the unit at the terminal
provided.

7. Equipotential terminal: In accordance with
national regulations, the unit has been fitted
with an equipotential terminal.

TDB/7 ELECTRICAL SPECIFICATIONS

VOLTAGE PHASE KW AMPS KW AMPS

230 1 7.8 33 13.3` 57
400 3 7.8 11.2 13.3 19

20 QUARTS 40 QUARTS

ELECTRICAL SUPPLY CONNECTION

REQUIREMENTS

Unit TDB/7-20 TDB/7-40

230V - 1 Phase 33 Amps 57 Amps
400V - 3 Phase 33 Amps 57 Amps

8

OM/SM-TDB/7(CE)

Initial Start-Up

IMPORTANT:
BE SURE ALL OPERATORS READ, UNDERSTAND AND FOLLOW THE OPERATING
INSTRUCTIONS, CAUTIONS, AND SAFETY INSTRUCTIONS CONTAINED IN THIS MANUAL.

Now that the kettle has been installed, you should
test it to ensure that the unit is operating correctly.

1. Remove all literature and packing materials
from inside and outside of the unit.

2. Confirm that the kettle tilts properly. Either
turn the crank or use the handle to tilt the
kettle and return it to the upright position.

2. Turn on the electrical service to the unit.

3. Pour two to four liters of water into the kettle.

4. Following “To Start Kettle” instructions in the
“Operation” section of this manual, begin
heating the water at the highest thermostat
setting. The heating indicator light should
come on immediately, and heating should
continue until the water boils.

WARNING

AVOID ALL DIRECT CONTACT WITH HOT
SURFACES. DIRECT SKIN CONTACT
COULD RESULT IN SEVERE BURNS.

AVOID ALL DIRECT CONTACT WITH HOT
FOOD OR WATER IN THE KETTLE.
DIRECT CONTACT COULD RESULT IN
SEVERE BURNS.

5. To shut down the unit, turn the thermostat dial to
“OFF”.

If the unit functions as described above, it is ready
for use. If the unit does not function as intended,
contact your local Groen Certified Service Agency.

A simple turn of the thermostat controls the Groen

TBD/7 Kettle

9

OM/SM-TDB/7(CE)

Operation

CE units have three lights on the Control Panel. The
“POWER” light comes on when the the unit is turned
on. It indicates that power is being supplied to the unit.
The “HEAT” light comes on when heating elements are
heating the kettle. The “LOW WATER” light will come
on when the water level in the jacket falls below
acceptable operating levels. Refer to “Jacket Filling and
Water Treatment” on Page 14.

A. To Start Kettle

1. EVERY DAY make sure that the jacket water
level is above the mid-point of the round
sight glass. If the level is low, service is
necessary.

2. Check the pressure gauge. If the gauge does
not show 20 to 30 inches of vacuum (i.e., a
reading of 20 to 30 below 0), see “Jacket
Vacuum” on page 14.

3. Turn on the electrical power to the unit.

4. Turn the thermostat dial to the desired
setting. The heating indicator light indicates
that the kettle is heating, and cycling of the
light on and off indicates that the kettle is
being held at the set temperature. Once in
each cycle the contactors in the support
housing will make a clicking sound. This is
normal.

B. To Transfer Product or Empty Kettle

The kettle is designed and manufactured to be
tilted in a controlled manner. On those units
equipped with a tilt handle, grasp the insulated
plastic ball firmly. Maintain a firm grip on handle
when tilting, while keeping kettle body in a tilted
position and when SLOWLY returning the kettle
body to an upright position. On those equipped
with crank tilt, turn the handle. The kettle will
remain in the position to which tilted until cranked
again.

On most TDB/7 units the jacket water level is shown
in a sight glass, right on the kettle.

WARNING

AVOID ALL DIRECT CONTACT WITH HOT
SURFACES. DIRECT SKIN CONTACT COULD
RESULT IN SEVERE BURNS.

AVOID ALL DIRECT CONTACT WITH HOT FOOD
OR WATER IN THE KETTLE. DIRECT CONTACT
COULD RESULT IN SEVERE BURNS.
TAKE SPECIAL CARE TO AVOID CONTACT WITH
HOT KETTLE BODY OR HOT PRODUCT, WHEN
ADDING INGREDIENTS, STIRRING OR
TRANSFERRING PRODUCT TO ANOTHER
CONTAINER.

10

OM/SM-TDB/7(CE)

CAUTION
DO NOT OVERFILL THE KETTLE WHEN
COOKING, HOLDING OR CLEANING. KEEP
LIQUIDS AT LEAST 2-3” (5-8 cm) BELOW THE
KETTLE BODY RIM TO ALLOW CLEARANCE
FOR STIRRING, BOILING PRODUCT AND SAFE
TRANSFER.

WARNING

WHEN TILTING KETTLE FOR PRODUCT
TRANSFER:

1) WEAR PROTECTIVE OVEN MITT AND

PROTECTIVE APRON.

2) USE DEEP CONTAINER TO CONTAIN AND

MINIMIZE PRODUCT SPLASHING.

3) PLACE CONTAINER ON STABLE, FLAT

SURFACE, AS CLOSE TO KETTLE AS
POSSIBLE.

4) STAND TO LEFT OR RIGHT OF KETTLE

(DEPENDING ON HANDLE PLACEMENT) WHILE
POURING — NOT DIRECTLY IN POUR PATH OF
HOT CONTENTS.

5) POUR SLOWLY, MAINTAIN CONTROL OF

KETTLE BODY HANDLE AT ALL TIMES, AND
RETURN KETTLE BODY TO UPRIGHT
POSITION AFTER CONTAINER IS FILLED OR
TRANSFER IS COMPLETE.

6) DO NOT OVERFILL CONTAINER. AVOID

DIRECT SKIN CONTACT WITH HOT
CONTAINER AND ITS CONTENTS.

When putting the cover on the kettle, position it
on top of kettle rim, with its flat edge facing the
pouring lip.

WARNING
AVOID ALL DIRECT CONTACT WITH HOT
SURFACES. DIRECT SKIN CONTACT COULD
RESULT IN SEVERE BURNS.

AVOID ALL DIRECT CONTACT WITH HOT
FOOD OR WATER IN THE KETTLE. DIRECT
CONTACT COULD RESULT IN SEVERE BURNS.

CAUTION
KEEP FLOORS IN FRONT OF THE KETTLE
WORK AREA CLEAN AND DRY. IF SPILLS
OCCUR, CLEAN AT ONCE TO AVOID SLIPS OR
FALLS.

Common Accessories

1. Lift Off Cover
As with stock pot cooking, an optional lift off cover

can speed up the heating of water and food
products. A cover helps retain heat in the cooking
vessel and reduces the amount of heat and humidity
released into the kitchen. Use of a cover can reduce
some product cook times and help maintain the
temperature, color and texture of products being
held or simmered for extended periods.

Make sure the handle is secure on the lift off cover
before using. ALWAYS use the handle to place or
remove cover from the kettle. Wear protective oven
mitts and a protective apron.

Lift the rear edge of the cover first.

When removing cover:

a) Firmly grasp the handle.
b) Lift rear edge (farthest from operator) 1-2”

(3-5 cm) to allow any steam and water vapor
to escape the cooking vessel. Wait 2-3
seconds.

c) Tilt cover to 45-60° angle and allow any hot

condensate or product to roll off cover back
into kettle.

d) Remove cover, ensuring that any remaining

hot condensate or product does not drip on
operator, floor or work surfaces.

e) Place cover on safe, flat, sanitary, out-of-the-

way surface, or return to kettle rim.

11

OM/SM-TDB/7(CE)

CAUTION
DO NOT TILT KETTLE BODY WITH COVER IN
PLACE. COVER MAY SLIDE OFF, CAUSING
INJURY TO OPERATOR.

2. Basket Insert
An optional kettle basket insert can assist in cooking

water-boiled products including eggs, potatoes,
vegetables, shell fish, pasta and rice. The nylon
mesh liner must be used when cooking product
smaller than the mesh size of the basket, which is
approximately 1/4” (6 mm). This includes rice and
small pasta shapes.

Tips For Use.
a) Allow for the water displacement of the basket

and product to be cooked. This may mean only
filling the kettle half full of water. Test the basket
and product displacement with the kettle OFF,
and with cold water in the kettle.

CAUTION
DO NOT OVERFILL THE KETTLE WHEN
COOKING, HOLDING OR CLEANING. KEEP
LIQUIDS A MINIMUM OF 2-3” (5-8 cm) BELOW
THE KETTLE BODY RIM TO ALLOW CLEARANCE
FOR STIRRING, BOILING AND SAFE PRODUCT
TRANSFER.

WARNING
AVOID ALL DIRECT CONTACT WITH HOT
SURFACES. DIRECT SKIN CONTACT COULD
RESULT IN SEVERE BURNS.

AVOID ALL DIRECT CONTACT WITH HOT FOOD
OR WATER IN THE KETTLE. DIRECT CONTACT
COULD RESULT IN SEVERE BURNS.

b) Load basket on a level, stable work surface.
c) Lift the loaded basket with both hands. Get help

from another person if the basket is too heavy
for safe handling.

before moving basket away from the kettle.
Do not rest kettle basket on kettle rim or
pouring lip. If basket is too heavy for
individual to lift and safely move, get help
from another person. Remove product
immediately from basket into another
container, being sure to avoid contact with
hot product and hot basket or. . .

g) Place basket with food on stable, flat

surface, setting it inside a solid steamer or
bake pan, to catch any remaining hot water
draining from product.

Sequence of Operation

The following “action-reaction” outline is provided to
help the user understand how the equipment works.

When the operator starts up the kettle by turning the
operating thermostat dial from “OFF” to a desired
setting, the thermostat switch closes. This lights up
the heating indicator light and causes the contactors
to close, allowing power to flow to heating elements.
When the temperature of the steam jacket reaches
the value corresponding to the dial setting, the
thermostat switch opens. This turns off the heating
indicator light and causes the contactors to open,
stopping the power to the heaters. As soon as the
thermostat senses that the kettle is cooling below the
set point, the thermostat switch closes, the heating
indicator light comes on, the contactors close, and
the heaters come on again. On-off cycling continues,
keeping the kettle at the set temperature This is why
the heating indicator light cycles on and off during
normal operation. Every time the kettle is tilted, the
tilt cut-off switch interrupts the power supply to the
heaters, so that the heating elements will not operate
while not submerged in the jacket water.

If steam pressure greater than 50 PSI is generated
in the jacket, the safety valve will open and relieve
the excess pressure.

If the jacket water level gets too low and the heating
elements overheat, the high-limit control will open,
shutting off power to the elements until the kettle
cools.

Setting the operating thermostat dial to “OFF” shuts
down all control and heating circuits.

d) Slowly lower product into kettle.
e) When removing basket with cooked product, lift

basket straight up, ensuring bottom of basket
clears the rim and pouring lip of the kettle. Wear
protective oven mitts and protective apron.

f) Allow hot water to fully drain from product,

12

OM/SM-TDB/7(CE)

Maintenance

NOTICE: Contact Groen or an authorized Groen representative when repairs are required.

1. Periodic Maintenance

A Maintenance & Service Log is provided at the
back of this manual. Each time maintenance is
performed on your Groen kettle, enter the date of
the work, what was done, and who did it. Keep this
manual on file and available for operators to use.

Periodic inspection will minimize equipment down
time and increase the efficiency of operation. The
following points should be checked:

[BY OPERATOR]

a. Check the pressure/vacuum gauge every day.

The gauge should show a vacuum of 20 to 30
inches, when the kettle is cold. If it does not,
see “Jacket Vacuum” on page 14.

service representative.

d. The inside of the support housing should be

kept clean.

e. At least twice a year, grease the two trunnion

bearings. The bearings are located within
the kettle support housing. Remove the
access panels from the support housing with
a screwdriver to gain access to the grease
fittings. Use a lithium-based, multi-purpose
grease. When the access panels are
removed, the mounting bolts for the trunnion
bearings and tilt switch can also be checked
for tightness.

WARNING
WHEN TEST ING, AVOID ANY EXPOSURE TO
THE STEAM BLOWING OUT OF THE SAFETY
VALVE. DIRECT CONTACT COULD RESULT IN
SEVERE BURNS.
DISCONNECT ELECTRICAL POWER FROM
THE KETTLE BEFORE ATTEMPTING TO
GREASE THE TRUNNION BEARINGS.

The pressure gauge should show a vacuum of 20
to 30 inches when the kettle is cold.

b. Also check the jacket water level each day. It

should be above mid point of the round sight
glass. If the level is low, see “Jacket Filling and
Water Treatment” on page 14.

[BY SERVICE TECHNICIAN]

c. Test the safety valve at least twice each month.

Test the valve with the kettle operating at 15 psi
(105 kPa), by pulling up the test chain for at
least five seconds. Then release the chain and
let the valve snap shut. If the valve does not
activate, (there is no evidence of discharge, or
the valve leaks) stop using the kettle
immediately and contact a qualified Groen

f. On the crank-tilt models, the gear housing has

fittings for proper lubrication of moving parts.
Because the gears do not run in oil, periodic

Test the safety valve at least twice each month.

13

OM/SM-TDB/7(CE)

lubrication with grease is necessary. Frequency of
lubrication will depend on operating conditions, but
the service should be performed at least once every
six months.

Add grease through the Zerk fittings on the gear
housing until you see grease flow out of the
bearings around the trunnion shaft. Also place
a liberal amount of grease on the gear to cover
the arc that is in contact with the worm gear.
When finished, reassemble access panels to
support housing.

Electrical wiring should be kept securely
connected and in good condition.

2. Jacket Vacuum

When the kettle is cold, a positive pressure reading
or a reading around zero on the pressure/vacuum
gauge indicates the presence of air in the jacket. Air
in the jacket slows down the heating of the kettle.

To remove air:
a. Start the unit. (See the “Operation” section of

this manual.) (Be sure there is water or product
in the kettle when heating).

d. Use a funnel and add water to jacket.
e Check water level in jacket, by viewing water

level indicator glass.

f. Continue to add water until the water level

indicator glass is 3/4 full.

g Close shutoff valve, and install fill plug.

Follow procedure in “Jacket Vacuum” to
remove air from kettle jacket.

3. Water Treatment Procedure

WARNING
TO AVOID INJURY, READ AND FOLLOW ALL
PRECAUTIONS STATED ON THE LABEL OF
THE WATER TREATMENT COMPOUND.

a. Obtain water treatment compound and a PH

test kit from your authorized Groen parts
distributor.

b. Fill the mixing container with the measured

amount of water required. (See the table at
right). Use distilled water.

b. When the pressure/vacuum gauge reaches a

positive pressure reading of five PSI, release
the trapped air and steam by pulling up on the
safety valve for about 1 second. Repeat this
step, then let the chain snap back into the
closed position.

3. Jacket Filling and Water Treatment

The jacket was charged at the factory with the
proper amount of treated distilled water. You may
need to restore the water to its proper level, either
because water was lost as steam during venting or
because treated water was lost by draining.

IMPORTANT
Pressure gauge must read 0 PSI or less before
you fill jacket with water.

To fill jacket with water:
a. If you are replacing water lost as steam, use

distilled water. If you are replacing treated water
that ran out of the jacket, prepare more treated
water as directed in step 3, “Water Treatment
Procedure”.

b. Remove fill plug with open-end wrench or

crescent wrench.

c. Hang a strip of pH test paper on the rim of

the container, with about 25 mm of the strip
below the surface of the water.

d. Measure the water treatment compound you

will be using. (One way to do this is to add
the compound from a measuring cup.)

e. Stir the water continuously, while you slowly

add water treatment compound, until the
water reaches a pH between 10.5 and 11.5.
Judge the pH by frequently comparing the
color of the test strip with the color chart
provided in the pH test kit.

f. Record the exact amounts of water and

treatment compound used. These amounts
may be used again, if the same sources of
water and compound are employed to refill
the jacket in the future. However, it is
advisable to check the pH every time treated
water is prepared. For optimum
performance, use correctly treated, distilled
water.

c Open shutoff valve (turn handle 90° on ball

valve).

14

OM/SM-TDB/7(CE)

4. Component Replacement

Model Jacket Capacity

TDB/7-20 3.8 Liters
TDB/7-40 4.7 Liters

BEFORE REPLACING ANY PARTS,
DISCONNECT THE UNIT FROM THE
ELECTRIC POWER SUPPLY.

Wiring is marked as shown on the schematic
drawings. Be sure new components are wired in
the same manner as the old.

WARNING

Troubleshooting

Your kettle is designed to operate smoothly and efficiently if properly maintained. However, the following is a list of
checks in the event of a problem. Wiring diagrams are furnished inside the service panel and at the back of this
manual. Items followed by X, should only be done by a qualified service representative. USE OF ANY

REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY GROEN OR ITS AUTHORIZED DISTRIBUTORS
CAN INJURE TO THE OPERATOR AND DAMAGE THE EQUIPMENT AND WILL VOID ALL WARRANTIES.

SYMPTOM WHO WHAT TO CHECK

Kettle will not heat, and heating
indicator will not come on.

Kettle will not heat, but heating
indicator comes on.

Kettle continues heating after it
reaches the desired temperature

Kettle stops heating before it
reaches the desired temperature.

Kettle heats slowly User a. For air in the jacket. See “Jacket Vacuum” in the

Safety valve pops. User a. For air in the jacket. See “Jacket Vacuum” in the

User a. Electric power supply to the unit.

b. Water level in jacket.

Auth Service
Rep Only

Auth Service
Rep Only

User a. Thermostat dial setting.
Auth Service

Rep Only

User a. Thermostat dial setting.
Auth Service

Rep Only

Auth Service
Rep Only

Auth Service
Rep Only

c. Control circuit fuses. Replace a blown fuse only with a fuse of
d. For loose or broken wires. X

e. Tilt cut-off switch. X
f. That pressure switch is open. X
g. Operation of variable thermostat. X
h. Low water cutoff. X

a. Contactor. X
b. Heater elements with ohmmeter for ground short or open

b. Thermostat circuit for short. X
c. Thermostat operation. The thermostat should click when the

d. Contactor, to determine whether it is energized or stuck.

b. Thermostat calibration. X
c. Thermostat operation. The thermostat should click when the

b. Heater elements with ohmmeter for ground short or open
c. Voltage of main power source. X

b. Pressure switch setting. X
c. Thermostat operation. Thermostat should click when the dial

d. Safety valve. If the valve pops at pressures below 49 PSI,
e. Contactor, to determine whether it is de-energized. X

X indicates items which must be performed by an authorized technician.

the same AMP rating. X

element. If element is defective, call Groen. X

dial is rotated above and below the setting for the temperature
of the kettle. X

dial is rotated above and below the setting for the temperature
of the kettle. X

“Maintenance” section of this manual.

element. If an element is defective, call Groen. X

“Maintenance” section of this manual.

is rotated above and below the setting for the temperature of
the kettle. X

replace it. X

15

OM/SM-TDB/7(CE)

User Instructions

Regulations and Safety Precautions

These Appliances have been CE marked on the basis of compliance with the EMC and Low Voltage Directive.
These appliances MUST BE installed by a competent person in conformity with the INSTALLATION AND

SERVICING INSTRUCTIONS and National Regulations in force at the time.
Particular attention MUST be paid to the following:

I.E.E. Regulations for Electrical Installations
Electricity at Work Regulations
Health and Safety at Work Act
Fire Precautions Act

Local and National Building Regulations
Those parts which have been protected by the manufacturer MUST NOT be adjusted by the User.
Users should be conversant with the appropriate provisions of the Fire Precautions Act. In particular the need for

regular servicing by a competent person to ensure the continued safe and efficient performance of the Appliance.

WARNING

TO PREVENT SHOCKS, ALL APPLIANCES WHETHER GAS OR ELECTRIC, MUST BE EARTHED.

Upon completion of the installation, the Owners Manual should be handed to the users and the installer should
instruct the responsible person(s) on the correct operation and maintenance of the Appliance. This equipment is
ONLY FOR PROFESSIONAL USE, and shall be operated by QUALIFIED persons. It is the responsibility of the
Supervisor or equivalent to ensure that users wear SUITABLE PROTECTIVE CLOTHING and to draw attention to
the fact that, some parts will, by necessity, become VERY HOT and will cause burns if touched accidentally.

IMPORTANT - READ FIRST - IMPORTANT The Groen Steam Jacketed Kettle you have just purchased has been
handcrafted from the finest materials, meticulously inspected, and carefully tested to ensure that you receive the
best possible product. With reasonable care and periodic maintenance, it will provide years of faithful service. It is
recommended that you establish a timetable for periodic maintenance as outlined in this manual. Space is provided
in the Service Log at the back of this manual.

Equipment Description

General

Groen models TDB/7 are stainless steel, steam
jacketed, table mounted, tilting kettles with a self­contained, electric-heated steam source. The kettle
body is welded into one piece and furnished with a
reinforced bar rim and welded "butterfly" pouring lip.
The interior of the kettle is polished to a 180 emery grit
finish, and the exterior is given a bright semi-deluxe
finish. The unit is ASME shop inspected and registered
with the National Board for working pressures up to 50
PSI. Kettle support, tilting mechanism, and controls are
contained in an enclosed base. Tilting is provided by a
self-locking, worm-and-gear device, or by a tilt handle.

Charged at the factory with treated, distilled water, the
steam source provides kettle temperature of 65/ C to
150/ C. Controls for the unit include a thermostat,

pressure gauge, gauge glass, safety valve, pressure
limit control, low water cut-off and an on/off switch.

Service connections are required for 230 Volt, single
phase, 50 Hz and 400 Volt, three phase, 50 Hz
electricity.

IMPORTANT: Prior to operation, clean out the
kettle pan thoroughly using hot water and
detergent. Rinse out and dry thoroughly.

16

OM/SM-TDB/7(CE)

Operational and Maintenance Safety

WARNING
INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL QUALIFIED TO WORK WITH
ELECTRICITY AND PLUMBING IN ACCORDANCE WITH ALL APPLICABLE CODES.

BEFORE REPLACING ANY PARTS, DISCONNECT THE UNIT FROM THE ELECTRIC POWER SUPPLY.
TO PREVENT SHOCKS, ALL APPLIANCES WHETHER GAS OR ELECTRIC, MUST BE EARTHED.

CAUTION
BE SURE ALL OPERATORS READ, UNDERSTAND, AND FOLLOW THE OPERATING INSTRUCTIONS,
CAUTIONS AND SAFETY INSTRUCTIONS CONTAINED IN THIS MANUAL.

Operation

1. Initial Operational Readiness Check

After the TDB/7 Kettle has been installed according
to service and installation instructions, perform initial
start-up as a test, to ensure that the unit is operating
correctly.

a. Remove all literature and packing material from

the interior and exterior of the unit.
b. Make sure electricity supply is switched on.
c. Ensure that the kettle is filled with water.
d. Check the water level in the jacket. The level

should be between the lines on the gauge glass.

If the level is low, the jacket water level will be

required to be topped up. (This will require a

service call).
e. Check the pressure gauge. If the gauge does not

show sufficient vacuum (20 to 30 below zero)

then the jacket will require venting. (This will

require a service call).
f. Switch the On/Off switch to the "On" position.

The "power on" neon will illuminate.

2. To Shut Down Kettle

a. Turn the thermostat dial to the "Off'' position.
b. Switch the On/Off switch to the "Off" position.
c. For a prolonged shut down, turn the electricity

main off.
Follow steps a and b.

3. Filling the Kettle

Prior to operation, thoroughly clean the kettle using
hot water and detergent.

Kettle capacities:

Model Maximum Capacity
TDB/7-20 18.8 Litres
TDB/7-40 37.6 Litres

To prevent surge boiling, no more than 80% of
the maximum capacity should be used.

4. Users Thermostat

g. Turn the thermostat dial to the required setting.

The "heat" neon will illuminate.

WARNING
AVOID CONTACT WITH THE FLUE. SURFACES
ARE VERY HOT AND WILL CAUSE BURNS. DO
NOT OBSTRUCT FLUE OPENING.

Provides automatic control of the Kettle Jacket
temperature at settings up to 147/ C maximum.

5. Sequence of Operation

The following “action-reaction” outline is provided to
help the user understand how the equipment works.

When the operator starts up the kettle by turning the
operating thermostat dial from “OFF” to a desired
setting, the thermostat switch closes. This lights up
the heating indicator light and causes the contactors
to close, allowing power to flow to heating elements.

When the temperature of the steam jacket reaches

17

OM/SM-TDB/7(CE)

the value corresponding to the dial setting, the
thermostat switch opens. This turns off the heating
indicator light and causes the contactors to open,
stopping the power to the heaters.

As soon as the thermostat senses that the kettle is
cooling below the set point, the thermostat switch
closes, the heating indicator light comes on, the
contactors close, and the heaters come on again. On­off cycling continues, keeping the kettle at the set
temperature. This is why the heating indicator light
cycles on and off during normal operation. Every time
the kettle is tilted, the tilt cut-off switch interrupts the
power supply to the heaters, so that the heating
elements will not operate while not submerged in the
jacket water.

If steam pressure greater than 50 PSIG is generated
in the jacket, the safety valve will open and relieve the
excess pressure.

TDB/7 Kettle with Tilt Handle

The kettle is designed to be tilted in a controlled
manner. Grasp the insulated plastic ball firmly.
Maintain a firm grip on the handle when tilting, while
keeping the kettle body in a tilted position, and when
slowly returning the kettle body to an upright
position.

WARNING
DO NOT STAND IN FRONT OF THE KETTLE
BODY WHEN TILTING IT. BE CAREFUL TO
KEEP HOT CONTENTS FROM SPILLING.
ENSURE PEOPLE ARE KEPT AWAY FROM
THE KETTLE WHEN EMPTYING THE KETTLE.

If the jacket water level gets too low before the
heating elements overheat, the high-limit control will
open and shut off power to the elements until the
kettle cools.

Setting the operating thermostat dial to “OFF” shuts
down all control and heating circuits.

6. To Empty Kettle
TDB/7 Kettles with Crank Tilt

To tilt the body of the kettle forward, turn the hand
crank on the front of the cabinet anti-clockwise. The
body will stay in the position it holds when you stop
turning the handle. To return the body to the upright
position, turn the crank clockwise.

7. Power Failure

If the power to the unit fails do not attempt to
operate the appliance until the electricity supply is
re-established.

When the power comes back on follow the steps in
Paragraph 8.2.1 Initial Kettle Operational Readiness
Check.

18

1. Suggested Tools:

a. Cleaner, such as Klenzade HC-10 or HC-32

from ECOLAB, Inc.
b. Kettle brushes in good condition.
c. Sanitizer such as Klenzade XY-12.
d. Film remover such as Klenzade LC-30.

1. Precautions

Before cleaning, shut off the kettle by turning the
thermostat dial to “OFF,” and shut off all electric
power to the unit at a remote switch, such as the
circuit breaker.

WARNING
KEEP WATER AND SOLUTIONS AWAY FROM
CONTROLS AND ELECTRICAL EQUIPMENT.
NEVER SPRAY THE SUPPORT HOUSING OR
ELECTRICAL CONNECTIONS.

OM/SM-TDB/7(CE)

Cleaning

Use only a sponge, cloth or plastic brush to clean
the kettle.

CAUTION
MOST CLEANERS ARE HARMFUL TO THE
SKIN, EYES, MUCOUS MEMBRANES, AND
CLOTHING. PRECAUTIONS SHOULD BE
TAKEN. WEAR RUBBER GLOVES, GOGGLES
OR FACE SHIELD, AND PROTECTIVE
CLOTHING. READ THE WARNINGS AND
FOLLOW THE DIRECTIONS ON THE LABEL OF
THE CLEANER CAREFULLY

3. Procedure

a. Clean food-contact surfaces as soon as

possible after use. If the unit is in continuous
use, thoroughly clean and sanitize the interior
and exterior at least once every 12 hours.

WARNING

AVOID ANY DIRECT CONTACT WITH HOT
SURFACES. DIRECT SKIN CONTACT COULD
RESULT IN SEVERE BURNS.

b. Scrape and flush out food residues. Be careful

not to scratch the kettle with metal
implements.

Scrapers or steel wool can harm the kettle surface.

c. Prepare a hot solution of the detergent/ cleaning

compound as instructed by the supplier. Clean
the unit thoroughly. A cloth moistened with
cleaning solution can be used to clean controls,
housings, and electrical conduits.

d. Rinse the kettle thoroughly with hot water, then

drain completely.

e. As part of the daily cleaning program, clean

soiled external and internal surfaces.
Remember to check the sides of the unit and
control housing.

f. To remove stuck materials, use a brush,

sponge, cloth, plastic or rubber scraper, or
plastic wool with the cleaning solution. To
reduce effort required in washing, let the
detergent solution sit in the kettle and soak into
the residue. Do NOT use abrasive materials or

19

OM/SM-TDB/7(CE)

metal tools that might scratch the surface.
Scratches make the surface harder to clean
and provide places for bacteria to grow.

Do NOT use steel wool, which may leave
particles in the surface and cause eventual
corrosion and pitting.

g. The outside of the unit may be polished with a

stainless steel cleaner such as “Zepper” from
Zep Manufacturing Co.

h.h. When equipment needs to be sanitized, use a

solution equivalent to one that supplies 200
parts per million available chlorine. Obtain
advice on sanitizing agents from your supplier
of sanitizing products. Following the supplier’s
instructions, apply the agent after the unit has
been cleaned and drained. Rinse off the
sanitizer thoroughly.

NOTICE
NEVER LEAVE A CHLORINE SANITIZER IN
CONTACT WITH STAINLESS STEEL
SURFACES LONGER THAN 30 MINUTES.
LONGER CONTACT CAN CAUSE STAINING
AND CORROSION.

i. It is recommended that each piece of equipment

be sanitized just before use.

j. If there is difficulty removing mineral deposits or

a film left by hard water or food residues, clean
the kettle thoroughly and then use a deliming
agent, like Groen Delimer/Descaler (Part
Number 114800) or Lime-Away from Ecolab, in
accordance with the manufacturer’s directions.
Rinse and drain the unit before further use.

k. If cleaning problems persist, contact your

cleaning product representative for assistance.
The supplier has a trained technical staff with
laboratory facilities to serve you.

20

OM/SM-TDB/7(CE)

Parts List - Kettle Body - Pull Tilt Model

To order parts, contact your Groen Certified Service Agency. Supply the model designation, part description, part
number, quantity, and, where applicable, voltage and phase.

21

OM/SM-TDB/7(CE)

Replacement Parts List

Pull Tilt Models

22

Replacement Parts List

Crank Tilt Models

OM/SM-TDB/7(CE)

23

OM/SM-TDB/7(CE)

Parts List

To order parts, contact your Groen Certified Service Agency. Supply the model designation, part description, part number,
quantity, and, where applicable, voltage and phase.

Key Description P/N H C Key Description P/N H C

1 Base Weldment 122185 x x 36 Bullseye sight glass 108554 x x
2 Cladding, top, pedestal 122052 x x 37 Thermostat knob 122054 x x
3 Cladding, side, pedestal 122051 x x 38 Thermostat 012313 x x
4 Cladding, panel, pedestal 122053 x x 39 Water level probe 015589 x x
5 Pillow block, 1-1/2" bore 002989 x x 40 Bottom Cover 003141 x x
6 Shim 122031 x x 41 Nut, hex 1/4-20 012940 x x
7 Pedestal, machined 117786 x 42 Pressure switch 096963 x x
8 Bearing with snap ring 002790 x 43 Reducing bushing 1/2 x 1/4 NPT 008739 x x

9 Worm shaft 113057 x 44 Elbow Assembly 101543 x x
10 Worm gear 3/4" bore 012026 x 45 Bottom cover bracket 002916 x x
11 Spacer Washer 084956 x 46 Screw, round head #6-32 x 3/8" 009697 x x
12 Hand wheel 012061 x 47 Thermostat adapter 107172 x x
13 Roll pin, 1/4" x 1" 012614 x 48 Gasket bottom cover 007937 x x
14 Gear bushing 113055 x 49 Safety Valve 097005 x x
15 Set screw, socket 3/8-16 x 1" 005593 x 50 Pressure gauge 084208 x x
16 Gear sector, 12 DP 009829 x 50a Pressure gauge lens 087635 x x
17 Key, 1/4" sq x 1-1/4" round ends 009262 x 51 Water fill assembly 101528 x x
18 Spacer washer 1/4" 122117 x 52 Kettle body wire harness 096938 x x
19 Pedestal, weldment 128517 x 53 Handle assembly 012695 x
20 Tilt switch & bracket assembly 127635 x 53a Ball knob 012691 x
21 Stop assembly 065527 x 53b Tolerance ring 012692 x
22 Set collar 065528 x 53c Handle rod 013597 x
23 Grommet 003492 x x -- Equipotential terminal assembly 122021 x x
24 Elec. component mounting panel 122103 x x -- Power light 116381 x x
25 Contactor 122042 x x -- Heat & low water light 116382 x x
26 Relay socket base 117738 x x -- Power switch 122004 x x
27 Water level sensor 117737 x x -- Washer, lock 3/8", MS 005702 x x
28 Terminal block 088214 x x -- Washer, lock 3/8" SS 005618 x x
29 Fuse block 077840 x x -- Screw, hex 3/8-16 x 1" SS 005612 x x
30 Ground lug 002863 x x -- Screw, hex 1/2-13 x 1" 005622 x x
31 Tilt switch & bracket assembly 113074 x -- Washer, lock 1/2" 005735 x x
32 Nut, Keps, 1/4-20 012940 x x -- Nut, hex 1/2-13 005705 x x
35 Indicator lamp 016028 x x

H = Pull Tilt Model C = Crank Tilt Models
– = Item not shown in illustrations

24

Wiring Diagram

OM/SM-TDB/7(CE)

25

OM/SM-TDB/7(CE)

Service Log

Model No. _______________________________ Purchased From _________________________
Serial No. _______________________________ Location ________________________________
Date Purchased __________________________ Date Installed ___________________________
Purchase Order No. ______________________ For Service Call __________________________

Date Service Performed Performed By

References

KLENZADE SALES CENTER ECOLAB. Inc.
370 Wabasha
St. Paul, Minnesota 55102
800/352-5326 or 612/293-2233

NATIONAL FIRE PROTECTION ASSOCIATION
60 Battery March Park
Quincy, Massachusetts 02269

NFPA/54 - Installation of Gas Appliances & Gas

Piping

NFPA/70 - The National Electrical Code

NATIONAL SANITATION FOUNDATION
3475 Plymouth Rd.
Ann Arbor, Michigan 48106

UNDERWRITERS LABORATORIES, INC.
333 Pfingsten Road
Northbrook, Illinois 60062

ZEP MANUFACTURING CO.
1310-T Seaboard Industrial Blvd.
Atlanta, Georgia 30318

26

OM/SM-TDB/7(CE)

Limited Warranty To Commercial Purchasers*

(for Areas Outside of the U.S. and Canada)

Groen Foodservice Equipment ("Groen Equipment") has been skillfully manufactured, carefully inspected
and packaged to meet rigid standards of excellence. Groen warrants its Equipment to be free from defects
in material and workmanship for twelve months from date of installation or eighteen months from date of
shipment with the following conditions and subject to the following limitations.

I. This parts warranty is limited to Groen Equipment sold to the original commercial purchaser/users

(but not original equipment manufacturers), at its original place of installation, in areas outside the
U.S. and Canada.

II. Damage during shipment is to be reported to the carrier, is not covered under this warranty, and is

the sole responsibility of the purchaser/user.

III. Groen, or an authorized service representative, will repair or replace parts, at Groen's sole

election, for any Groen Equipment, including but not limited to, draw-off valves, safety valves, gas
and electric components, found to be defective during the warranty period.

IV. This warranty does not cover boiler maintenance, calibration, or periodic adjustments as specified

in operating instructions or manuals, and consumable parts such as scraper blades, gaskets,
packing, etc., or labor costs incurred for removal of adjacent equipment or objects to gain access
to Groen Equipment. This warranty does not cover defects caused by improper installation, abuse,
careless operation, or improper maintenance of equipment. This warranty does not cover damage
caused by poor water quality or improper boiler maintenance.

v. THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, EACH OF WHICH IS HEREBY EXPRESSLY
DISCLAIMED. THE REMEDIES DESCRIBED ABOVE ARE EXCLUSIVE AND IN NO EVENT
SHALL GROEN BE LIABLE FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR THE BREACH OR DELAY IN PERFORMANCE OF THIS WARRANTY.

VI. Groen Equipment is for commercial use only. If sold as a component of another (O.E.M.)

manufacturer's equipment or if used as a consumer product, such Equipment is sold AS IS and
without any warranty.

* (Covers All Food Service Equipment Ordered After October 1,1995)

27

1055 Mendell Davis Drive
Jackson, MS 39272
Telephone [phone]
Fax [phone]

OM/SM-TDB/7(CE)

Part Number 128433

Revised 7/99