Operator Manual
Simplicity™ Bubbler
Crathco® Cold Beverage Dispensers
Activate your warranty now at
http://gmcw.com/warranty-registration
Model CS-2D-16
Model CS-2E-16
Model CS-3L-16
(cULus certification applies only to United States and Canada models.)
|
Table of Contents |
|
|
Safety Information........................ |
2 |
Daily Cleaning ............................... |
8 |
Specifications................................. |
3 |
Troubleshooting.......................... |
11 |
Installation and Set-Up................. |
4 |
Basic Machine Parts .................... |
14 |
Product Preparation & Use........... |
7 |
|
|
Thank you for purchasing this quality cold beverage dispenser. For your safety and the safety of others, read all warnings and the operator’s manual before installing or using the product. Properly instruct all operators. Keep training records. For future reference, record serial number here:
Grindmaster-Cecilware |
|
|
4003 Collins Lane, Louisville, KY 40245 USA |
Grindmaster-Cecilware provides the industry’s |
|
Phone: 502.425.4776 Toll Free: 800.695.4500 |
BEST warranty. Visit gmcw.com for warranty |
|
Fax: 502.425.4664 |
terms and conditions. |
Web: gmcw.com Email: info@gmcw.com |
|
|
©2017 Grindmaster-Cecilware |
|
|
0917 Form # CC-330-05 |
||
Printed in Thailand |
Part # 390-00003 |
Safety Information
Important Safety Information
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
For your safety and the safety of others, read all warnings and the operator manual before installing or using the product.
DANGER: This term warns the user of imminent hazard that will result in serious injury or death.
WARNING: This term refers to a potential hazard or unsafe practice, which could result in serious injury or death. CAUTION: This term refers to a potential hazard or unsafe practice, which could result in minor or moderate injury.
NOTICE: This term refers to information that needs special attention or must be fully understood.
WARNING/ AVERTISSEMENT/ ADVERTENCIA
The appliance is not intended for outdoor use.
Do not clean with a water jet or use in an area where a water jet may be used.
Cleaning and maintenance shall be made only by properly trained persons with supervision.
CAUTION/ ATTENTION/ ATENCIÓN
Lifting hazard. Single person lift could cause injury. Use assistance when moving or lifting.
Sharp edges can cause personal injury. Handle with care.
The appliance is not to be used by persons (including children 8 years and above) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Be sure to provide supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children must be supervised to ensure they do not play with the appliance.
For safe and proper operation the appliance has to be placed in a stable horizontal position.
The appliance is only to be installed in locations where it can be overseen by trained personnel.
NOTICE/ AVIS/ AVISO
Observe machine voltage configuration. Do not apply improper voltage to machine or damage to machine will occur.
Do not use extension cord.
Do not operate the appliance below 1.7°C (35°F) or above 40°C (104°F).
Clean and sanitize unit before first use.
2 |
Crathco® |
Simplicity Bubbler |
|
|
|
Specifications
Northern America
Model |
Description |
Dimensions (H x W x D) |
Electrical |
Certifications |
|
CS-2E-16 |
(2) |
2.4 gallon (9L) bowls, |
27.5” x 10.5” x 17.75” |
120V / 60 Hz / 3.6A |
C-UL US, NSF |
|
agitator model. |
|
|
|
|
CS-2E-16-S |
(2) |
2.4 gallon (9L) bowls, |
27.5” x 10.5” x 17.75” |
120V / 60 Hz / 3.6A |
C-UL US, NSF |
|
spray model. |
|
|
|
|
CS-4E-16 |
(4) |
2.4 gallon (9L) bowls, |
27.5” x 20.5” x 17.75” |
120V / 60 Hz / 8.5A |
C-UL US, NSF |
|
agitator model. |
|
|
|
|
CS-4E-16-S |
(4) |
2.4 gallon (9L) bowls, |
27.5” x 20.5” x 17.75” |
120V / 60 Hz / 8.5A |
C-UL US, NSF |
|
spray model. |
|
|
|
|
CS-1D-16 |
(1) |
4.75 gallon (18L) bowl, |
27.5” x 10.5” x 17.75” |
120V / 60 Hz / 3.6A |
C-UL US, NSF |
|
agitator model. |
|
|
|
|
CS-1D-16-S |
(1) |
4.75 gallon (18L) bowl, |
27.5” x 10.5” x 17.75” |
120V / 60 Hz / 3.6A |
C-UL US, NSF |
|
spray model. |
|
|
|
|
CS-2D-16 |
(2) |
4.75 gallon (18L) bowls, |
27.5” x 20.5” x 17.75” |
120V / 60 Hz / 8.5A |
C-UL US, NSF |
|
agitator model. |
|
|
|
|
CS-2D-16-S |
(2) |
4.75 gallon (18L) bowls, |
27.5” x 20.5” x 17.75” |
120V / 60 Hz / 8.5A |
C-UL US, NSF |
|
spray model. |
|
|
|
|
CS-3D-16 |
(1) |
4.75 gallon (18L) bowl, |
27.5” x 20.5” x 17.75” |
120V / 60 Hz / 8.5A |
C-UL US, NSF |
|
(2) |
2.4 gallon (9L) bowls, |
|
|
|
|
agitator model. |
|
|
|
|
CS-3D-16-S |
(1) |
4.75 gallon (18L) bowl, |
27.5” x 20.5” x 17.75” |
120V / 60 Hz / 8.5A |
C-UL US, NSF |
|
(2) |
2.4 gallon (9L) bowls, |
|
|
|
|
spray model. |
|
|
|
|
CS-3L-16 |
(3) |
4.75 gallon (18L) bowls, |
31.3” x 20.5” x 17.75” |
120V / 60 Hz / 8.5A |
C-UL US, NSF |
|
agitator model. |
|
|
|
|
CS-3L-16-S |
(3) |
4.75 gallon (18L) bowls, |
31.3” x 20.5” x 17.75” |
120V / 60 Hz / 8.5A |
C-UL US, NSF |
|
spray model. |
|
|
|
|
Export |
|
|
|
|
|
Model |
Description |
Dimensions (H x W x D) |
Electrical |
Certifications/ |
||
|
|
|
|
|
|
Declarations |
CS-2E-10 |
(2) |
2.4 gallon (9L) bowls, |
25.3” x 10.5” x 17.6” |
100V |
/ 50/60 HZ / 3.6A |
NSF |
|
agitator model. |
64 cm x 27 cm x 45 cm |
|
|
|
|
CS-2E-10-S |
(2) |
2.4 gallon (9L) bowls, |
25.3” x 10.5” x 17.6” |
100V |
/ 50/60 HZ / 3.6A |
NSF |
|
spray model. |
64 cm x 27 cm x 45 cm |
|
|
|
|
CS-2E-22 |
(2) |
2.4 gallon (9L) bowls, |
25.3” x 10.5” x 17.6” |
230V |
/ 50/60 HZ / 1.5A |
NSF, CE |
|
agitator model. |
64 cm x 27 cm x 45 cm |
|
|
|
|
CS-2E-22-S |
(2) |
2.4 gallon (9L) bowls, |
25.3” x 10.5” x 17.6” |
230V |
/ 50/60 HZ / 1.5A |
NSF, CE |
|
spray model. |
64 cm x 27 cm x 45 cm |
|
|
|
|
CS-4E-22 |
(4) |
2.4 gallon (9L) bowls, |
25.5” x 20.4” x 17.7” |
230V |
/ 50/60 HZ / 4A |
NSF, CE |
|
agitator model. |
65 cm x 52 cm x 45 cm |
|
|
|
|
CS-4E-22-S |
(4) |
2.4 gallon (9L) bowls, |
25.5” x 20.4” x 17.7” |
230V |
/ 50/60 HZ / 4A |
NSF, CE |
|
spray model. |
65 cm x 52 cm x 45 cm |
|
|
|
|
CS-1D-22 |
(1) |
4.75 gallon (18L) bowl, |
25.3” x 10.5” x 17.6” |
230V |
/ 50/60 HZ / 1.5A |
NSF, CE |
|
agitator model. |
64 cm x 27 cm x 45 cm |
|
|
|
|
CS-1D-22-S |
(1) |
4.75 gallon (18L) bowl, |
25.3” x 10.5” x 17.6” |
230V |
/ 50/60 HZ / 1.5A |
NSF, CE |
|
spray model. |
64 cm x 27 cm x 45 cm |
|
|
|
|
CS-2D-22 |
(2) |
4.75 gallon (18L) bowls, |
25.5” x 20.4” x 17.7” |
230V |
/ 50/60 HZ / 4A |
NSF, CE |
|
agitator model. |
65 cm x 52 cm x 45 cm |
|
|
|
|
CS-2D-22-S |
(2) |
4.75 gallon (18L) bowls, |
25.5” x 20.4” x 17.7” |
230V |
/ 50/60 HZ / 4A |
NSF, CE |
|
spray model. |
65 cm x 52 cm x 45 cm |
|
|
|
|
CS-3D-22 |
(1) |
4.75 gallon (18L) bowl, |
25.5” x 20.4” x 17.7” |
230V |
/ 50/60 HZ / 4A |
NSF, CE |
|
(2) |
2.4 gallon (9L) bowls, |
65 cm x 52 cm x 45 cm |
|
|
|
|
agitator model. |
|
|
|
|
|
CS-3D-22-S |
(1) |
4.75 gallon (18L) bowl, |
25.5” x 20.4” x 17.7” |
230V |
/ 50/60 HZ / 4A |
NSF, CE |
|
(2) |
2.4 gallon (9L) bowls, |
65 cm x 52 cm x 45 cm |
|
|
|
|
spray model. |
|
|
|
|
|
CS-3L-22 |
(3) |
4.75 gallon (18L) bowls, |
29.0” x 20.4” x 17.7” |
230V |
/ 50/60 HZ / 4A |
NSF, CE |
|
agitator model. |
74 cm x 52 cm x 45 cm |
|
|
|
|
CS-3L-22-S |
(3) |
4.75 gallon (18L) bowls, |
29.0” x 20.4” x 17.7” |
230V |
/ 50/60 HZ / 4A |
NSF, CE |
|
spray model. |
74 cm x 52 cm x 45 cm |
|
|
|
Simplicity Bubbler |
Crathco® |
3 |
|
|
|
Installation and Set-Up
1. Place machine on counter with proper spacing.
•The appliance must be placed in a horizontal position.
•The appliance is suitable for indoor use only.
a. |
Place dispenser on |
b. |
|
stable counter strong |
|
|
enough to support |
|
|
its weight. |
|
Allow 5” (13 cm) on sides c. and 6” (15 cm) on back
for proper ventilation.
Top View
|
|
|
|
|
|
6” |
6” (15 cm) minimum |
|
|
|
|
|
|
|
(15 cm) |
machine spacing from |
|
|
|
|
|
|
|
|
|
wall |
|
|
|
|
|
|
5” (13 cm) minimum |
||
|
|
|
|
|
|
|||
|
5” |
|
|
5” |
|
machine spacing from |
||
(13 cm) |
(13 cm) |
wall or other machines |
Front View
Position machine away from heat emitting objects (i.e. ovens, grills, refrigeration equipment).
Recommended ambient temperature 75° F (25° C).
2. Install power cord.
a. Note proper voltage.
Observe machine voltage configuration. Do not apply improper voltage to machine or damage to machine will occur.
b. Plug cord into power outlet.
Do not use extension cord.
Failure to follow proper installation guidelines can damage equipment and void warranty.
CAUTION/ ATTENTION/ ATENCIÓN
1.This appliance is not intended for the use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by person responsible for their safety.
2.Children should be supervised to ensure that they do not play with the appliance.
3.This appliance is only to be installed in locations where it can be overseen by trained personnel.
4 |
Crathco® |
Simplicity Bubbler |
|
|
|
Installation - Agitator Function (Model CS-XX-YY)
1. 2.
Install mixing impeller.
3. 4.
Install bowl gasket.
a. |
b. |
Install assembled bowl. |
|
Place o-ring on dispense valve |
|||
NOTICE/TICE: AVIS/ AVISO: |
|||
(check if nicked or twisted). Place in |
|||
Machine must be OFF. |
|||
bowl. |
|
||
5. |
|
6. |
Install handle. |
Flip out support bracket for |
|
drip tray. |
8. |
9. |
a. |
b. |
|
Mix product in clean container. |
Install bowl cover. |
|
Fill bowl with product. |
|
|
Simplicity Bubbler |
Crathco® |
CAUTION/ ATENCIÓN/ ATTENTION Sharp edges can cause personal injury. Handle with care.
Replace axle if flange |
Replace impeller if |
thickness is less than |
bearing surface is |
0.75mm |
worn more than |
(0.03 inch) |
0.5mm (0.02 inch). |
thick. |
|
Inspect for wear.
Insert bowl lip underneath of lock position on the back of top tray.
Then, press down on the front of the bowl until you hear a click indicating the bowl is locked properly in place.
7.
Place drip tray cover on drip tray.
Install drip tray.
10.
Turn power “on”.
5
Installation - Spray Function (Model CS-XX-YY-S)
1. |
2. |
|
CAUTION/ ATENCIÓN/ |
|
|
|
ATTENTION Sharp edges can |
|
|||
|
|
|
|||
|
|
|
|
||
|
|
|
cause personal injury. Handle |
|
|
|
|
|
with care. |
|
|
|
|
Replace axle if flange thick- |
Replace impeller if |
||
|
|
ness is less than 0.75mm |
bearing surface is |
||
|
|
(0.03 inch) thick. |
worn more than |
||
|
|
|
|
0.5mm (0.02 inch). |
Install mixing impeller. |
|
Install bowl gasket. |
|
|
|
Inspect for wear. |
|||
|
|
|
||
|
|
|
|
|
3. |
4. |
5. |
|
|
Insert bowl lip underneath of lock position on the back of top tray.
|
|
a. |
b. |
Install assembled bowl. |
|
|
|
|
|
|
|
|
|
|
|
Place o-ring on dispense valve |
NOTICE/ AVIS/ |
|
|
|
|
|
AVISO: |
|
Then, press down on the |
||
|
|
(check if nicked or twisted). |
|
|||
|
Install pump cover. |
|
front of the bowl until |
|||
|
Place in bowl. |
Machine must be OFF. you hear a click indicating |
||||
|
|
|
|
|
|
the bowl is locked proper- |
|
|
|
|
|
|
ly in place. |
|
|
|
|
|
|
|
6. |
7. |
|
8. |
9. |
|
|
Install spray tube to fit |
Install handle. |
Flip out support bracket Install drip tray and cover. |
|
for drip tray. |
|
with Pump cover. |
|
|
10. |
11. |
12. |
|
a. |
b. |
|
|
|
|
Mix product in clean container. |
Install bowl cover. |
Turn power “on”. |
|||
Fill bowl with product. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 |
|
Crathco® |
|
Simplicity Bubbler |
|
|
|
|
|
|
|