GA-F2A68HM-HD2
User's Manual
Rev. 1001
12ME-F268HD2-1001R
Motherboard
GA-F2A68HM-HD2
Nov. 19, 2014
Motherboard
GA-F2A68HM-HD2
Nov. 19, 2014
Copyright
© 2014 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.
In order to assist in the use of this product, carefully read the User's Manual.
For product-related information, check on our website at: http://www.gigabyte.com
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS,
drivers, or when looking for technical information. Example:
Table of Contents
GA-F2A68HM-HD2 Motherboard Layout......................................................................... |
4 |
|
GA-F2A68HM-HD2 Motherboard Block Diagram............................................................ |
5 |
|
Chapter 1 Hardware Installation...................................................................................... |
6 |
|
1-1 |
Installation Precautions..................................................................................... |
6 |
1-2 |
Product Specifications...................................................................................... |
7 |
1-3 |
Installing the APU............................................................................................. |
9 |
1-4 |
Installing the Memory........................................................................................ |
9 |
1-5 Installing an Expansion Card.......................................................................... |
10 |
|
1-6 Setup of the AMD Dual Graphics Configuration............................................. |
10 |
|
1-7 |
Back Panel Connectors.................................................................................. |
10 |
1-8 |
Internal Connectors........................................................................................ |
12 |
Chapter 2 BIOS Setup................................................................................................... |
17 |
|
2-1 |
Startup Screen................................................................................................ |
18 |
2-2 |
M.I.T................................................................................................................ |
18 |
2-3 |
System Information......................................................................................... |
22 |
2-4 |
BIOS Features................................................................................................ |
23 |
2-5 |
Peripherals...................................................................................................... |
26 |
2-6 |
Power Management........................................................................................ |
28 |
2-7 |
Save & Exit..................................................................................................... |
29 |
Chapter 3 Appendix....................................................................................................... |
30 |
|
3-1 |
Configuring SATA Hard Drive(s)..................................................................... |
30 |
3-2 |
Drivers Installation.......................................................................................... |
33 |
Regulatory Statements.............................................................................................. |
34 |
|
Contact Us................................................................................................................. |
36 |
- 3 -
KB_MS_USB
ATX_12V
VGA
DVI
R_USB30
HDMI
USB_LAN |
CI |
|
CPU_FAN |
||
|
AUDIO
Realtek® PCIEX16
GbE LAN
PCIEX1
iTE® Super I/O
PCI
CODEC
SPDIF_O
Socket FM2+
ATX
|
SYS_FAN1 2 |
|
2 |
|
1 |
3 |
|
BAT |
DDR3 |
DDR3 |
SATA3 |
|
|
|
|
GA-F2A68HM-HD2 |
|
|
|
M_BIOS |
|
|
|
|
|
AMD A68H |
|
B_BIOS |
|
|
|
CLR_CMOS |
SPEAKER |
SATA3 0 1 |
|
|
|
|
|
USB1 |
F_ |
|
PANEL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
F_AUDIO |
COM F_ |
USB2 F_ |
|
SYS_FAN2 |
Box Contents
55 |
GA-F2A68HM-HD2 motherboard |
|
|
55 |
Motherboard driver disk |
55 |
Two SATA cables |
55 |
User's Manual |
55 |
I/O Shield |
The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.
- 4 -
1 PCI Express x16 |
|||||||||||||
|
|
|
|
|
|
|
|||||||
PCIe CLK |
|
|
|
|
|
|
|
LAN |
|||||
|
|
|
|
|
|
|
|||||||
(100 MHz) |
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
RJ45 |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Realtek® |
|||||
|
|
|
|
|
|
|
|
GbE LAN |
|||||
|
|
|
|
|
|
|
|
||||||
|
|
|
|
x16 |
|
|
|
|
x1 |
||||
|
|
|
|
|
|
|
|
||||||
|
|
|
|
x1 |
PCI Express Bus |
||||||||
|
|
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 PCI Express x1
PCI Bus
PCI CLK
(33 MHz)
1 PCI
APU CLK+/- (100 MHz)
DISP CLK+/- (100 MHz)
AMD APU DDR3 2133/1866/
1600/1333 MHz
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dual Channel Memory |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
D-Sub |
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
DVI-D |
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HDMI |
|
|
|
|
|
|||||
|
|
UMI |
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dual BIOS |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 SATA 6Gb/s |
||||
|
AMD A68H |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 USB 3.0/2.0 |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8 USB 2.0/1.1 |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LPC |
|
|
|
|
iTE® |
|
|
COM |
|
||||||||||
|
|
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
Bus |
Super I/O |
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PS/2 KB/Mouse |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CODEC
(Center/Subwoofer |
(Front |
S/PDIFOut |
Out)Speaker |
Out)Speaker Out)Speaker |
|
MIC |
(Rear |
|
Line |
|
|
|
In |
|
|
Out |
|
|
Line |
|
For detailed product information/limitation(s), refer to "1-2 Product Specifications."
- 5 -
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:
•• Prior to installation, make sure the chassis is suitable for the motherboard.
•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.
•• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.
•• When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.
•• When handling the motherboard, avoid touching any metal leads or connectors.
•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.
•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.
•• Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.
•• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.
•• Before using the product, please verify that all cables and power connectors of your hardware components are connected.
•• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.
•• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.
•• Do not place the computer system on an uneven surface.
•• Do not place the computer system in a high-temperature environment.
•• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.
•• If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.
- 6 -
APU |
FM2+ Socket: |
|
- AMD A series processors |
-AMD Athlon™ series processors
(Go to GIGABYTE's website for the latest CPU support list.)
Chipset |
|
AMD A68H |
|
|
|
Memory |
|
2 x DDR3 DIMM sockets supporting up to 64 GB of system memory |
|
|
* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical |
|
|
memory is installed, the actual memory size displayed will be less than the size of |
|
|
the physical memory installed. |
*The maximum 64 GB of system memory can be supported using 16 GB (or above) memory modules. GIGABYTE will update the memory support list on the official website when the memory modules are available on the market.
Dual channel memory architecture
Support for DDR3 2133/1866/1600/1333 MHz memory modules
Support forAMD Memory Profile (AMP)/Extreme Memory Profile (XMP) memory modules
(GotoGIGABYTE'swebsiteforthelatestsupportedmemoryspeeds andmemory modules.)
Onboard |
|
Integrated Graphics Processor: |
|
Graphics |
|
- |
1 x D-Sub port, supporting a maximum resolution of 1920x1200 |
|
|
- |
1 x DVI-D port, supporting a maximum resolution of 2560x1600 |
|
|
|
* Support for 2560x1600 resolution requires both a monitor and cable that support |
|
|
|
Dual Link DVI. |
|
|
|
* The DVI-D port does not support D-Sub connection by adapter. |
|
|
- |
1 x HDMI port, supporting a maximum resolution of 4096x2160 |
|
|
|
* The resolution of 4096x2160 can be supported when using an FM2+ APU; the |
|
|
|
maximum resolution supported is 1920x1200 when using an FM2 APU. |
|
|
|
* Support for HDMI 1.4a version. |
|
|
- |
Maximum shared memory of 2 GB |
Audio |
|
Realtek® ALC887 codec |
|
|
High Definition Audio |
||
|
|
2/4/5.1/7.1-channel |
*To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.
Support for S/PDIF Out
LAN |
|
Realtek® GbE LAN chip (10/100/1000 Mbit) |
||
Expansion Slots |
|
1 x PCI Express x16 slot, running at x16 |
|
|
|
|
(The PCI Express x16 slot conforms to PCI Express 3.0 standard.) |
||
|
|
|
* To support PCI Express 3.0, you must install an FM2+ APU. |
|
|
|
1 x PCI Express x1 slot |
||
|
|
(The PCI Express x1 slot conforms to PCI Express 2.0 standard.) |
||
|
|
1 x PCI slot |
||
Multi-Graphics |
|
Support for AMD Dual Graphics technology |
|
|
Technology |
|
|
* Only A series APUs support AMD Dual Graphics. |
|
|
Support for AMD Eyefinity technology |
|||
Storage Interface |
|
Chipset: |
|
|
|
|
- |
4 x SATA 6Gb/s connectors |
|
|
|
- |
Support for RAID 0, RAID 1, RAID 10, and JBOD |
|
USB |
|
Chipset: |
|
|
|
|
- |
2 x USB 3.0/2.0 ports on the back panel |
|
|
|
- |
8 x USB 2.0/1.1 ports (4 ports on the back panel, 4 ports available through |
|
|
|
|
the internal USB headers) |
|
|
|
|
|
|
|
|
|
- 7 - |
|
Internal |
1 x 24-pin ATX main power connector |
|
Connectors |
1 x 8-pin ATX 12V power connector |
|
|
4 x SATA 6Gb/s connectors |
|
|
1 x APU fan header |
|
|
2 x system fan headers |
|
|
1 x front panel header |
|
|
1 x front panel audio header |
|
|
1 x speaker header |
|
|
1 x S/PDIF Out header |
|
|
2 x USB 2.0/1.1 headers |
|
|
1 x serial port header |
|
|
1 x Clear CMOS jumper |
|
|
1 x chassis intrusion header |
|
Back Panel |
1 x PS/2 keyboard/mouse port |
|
Connectors |
1 x D-Sub port |
|
|
1 x DVI-D port |
|
|
1 x HDMI port |
|
|
2 x USB 3.0/2.0 ports |
|
|
4 x USB 2.0/1.1 ports |
|
|
1 x RJ-45 port |
|
|
3 x audio jacks (Line In, Line Out, Mic In) |
|
I/O Controller |
iTE® I/O Controller Chip |
|
Hardware |
|
System voltage detection |
Monitor |
|
APU/System temperature detection |
|
APU/System fan speed detection |
|
|
APU overheating warning |
|
|
APU/System fan fail warning |
|
|
APU/System fan speed control |
*Whether the fan speed control function is supported will depend on the cooler you install.
BIOS |
|
2 x 64 Mbit flash |
|
Use of licensed AMI UEFI BIOS |
|
|
Support for DualBIOS™ |
|
|
PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0 |
|
Unique Features |
|
Support for @BIOS |
|
|
Support for Q-Flash |
|
Support for Xpress Install |
|
Support for EasyTune |
|
* Available functions in EasyTune may differ by motherboard model. |
|
Support for Smart Recovery2 |
|
Support for ON/OFF Charge |
Bundled |
Norton® Internet Security (OEM version) |
Software |
|
Operating |
Support for Windows 8.1/7 32-bit/64-bit |
System |
Support for Windows XP 32-bit |
|
* To support Windows XP 32-bit, you must install an AMD FM2+ Kaveri APU. |
Form Factor |
Micro ATX Form Factor; 22.6cm x 17.4cm |
* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.
* Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s) for the software listed in the "Unique Features" and "Bundled Software" columns.
- 8 -
Read the following guidelines before you begin to install the APU:
•• Make sure that the motherboard supports the APU.
(Go to GIGABYTE's website for the latest APU support list.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the APU to prevent hardware damage.
•• Locate the pin one of the APU. The APU cannot be inserted if oriented incorrectly.
•• Apply an even and thin layer of thermal grease on the surface of the APU.
•• Do not turn on the computer if the APU cooler is not installed, otherwise overheating and damage of the APU may occur.
•• Set the APU host frequency in accordance with the APU specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including theAPU, graphics card, memory, hard drive, etc.
Installing the APU
Locate the alignment keys on the motherboard APU socket and the notches on the APU.
A Small Triangle |
FM2+ Socket |
A Small Triangle |
APU |
|
Marking Denotes Pin |
||||
|
Marking Denotes APU |
|||
One of the Socket |
|
|
||
|
Pin One |
|
||
|
|
|
Read the following guidelines before you begin to install the memory:
•• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.
•• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration
This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual
Channel memory mode will double the original memory bandwidth.
The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as following:
Channel 0: DDR3_2Channel 1: DDR3_1
Due to APU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1.Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.
2.When enabling Dual Channel mode with two memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used for optimum performance.
-9 -
Read the following guidelines before you begin to install an expansion card:
•• Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.
•• Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.
A.System Requirements
-- An AMD A series processor that supports AMD Dual Graphics technology -- Windows 8.1/7 operating system
-- An AMD Dual Graphics technology-supported motherboard and correct driver
-- An AMD graphics card that supports AMD Dual Graphics technology (for more details, please visit AMD's official website) and correct driver (For an FM2+ APU, please use an AMD R7 200 series graphics card; for an FM2 APU, please use an AMD Radeon™ HD 6000 graphics card.)
B.Installing the Graphics Cards and Configuring BIOS Setup
Step 1:
Observe the steps in "1-5 Installing an Expansion Card" and install an AMD Dual Graphics technology-supported graphics card on the PCIEX16 slot. Plug the monitor cable into the graphics card and start up your computer. Step 2:
Enter BIOS Setup to set the following items under the Peripherals\GFX Configuration menu: -- Set Integrated Graphics to Force.
-- Set UMA Frame Buffer Size to 512M or above.
Save the settings and exit BIOS Setup. Restart your computer.
C. Configuring the Graphics Card Driver
After installing the graphics card driver in the operating system, go to the AMDVISION Engine Control Center. After installing the graphics card driver in the operating system, go to the AMD VISION Engine Control Center. Browse to Performance\AMD Radeon™ Dual Graphics and ensure the Enable AMD Radeon Dual Graphics check box is selected.
USB 2.0/1.1 Port
The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
PS/2 Keyboard/Mouse Port
Use this port to connect a PS/2 mouse or keyboard.
D-Sub Port
The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200
(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports
D-Sub connection to this port.
- 10 -
DVI-D Port (Note 1)
The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 2560x1600.
Connect a monitor that supports DVI-D connection to this port. Please note that the actual resolutions supported are dependent on the monitor being used and support for 2560x1600 resolution requires both a monitor and cable that support Dual Link DVI.
USB 3.0/2.0 Port
The USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
HDMI Port
The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD
Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 4096x2160 (Note 2), but the actual resolutions supported are dependent on the monitor being used.
After installing the HDMI device, make sure to set the default sound playback device to HDMI.
A. Triple Display Configurations:
Triple-display configurations are supported after you install motherboard drivers in OS. Only dual-display configurations are supported during the BIOS Setup or POST process.
B. Playback of Blu-ray™ Discs:
In order to get better playback quality, when playing the Blu-ray™ discs, refer to the recommended system requirements (or better) below.
•• AMD A series processors
•• Memory: Two 1 GB DDR3 1333 MHz memory modules with dual channel mode enabled
•• BIOS Setup:At least 512 MB of UMAFrame Buffer Size (refer to Chapter 2, "BIOS Setup," "Peripherals\ GFX Configuration," for more information)
•• Playback software: CyberLink PowerDVD 10.0 or later (Note: Please ensure Hardware Acceleration is enabled. Whether Hardware Acceleration can be enabled for 3D Blu-ray discs is dependent on the
APU being used.)
•• HDCP compliant monitor(s)
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.
Connection/ |
|
|
|
|
|
|
|
|
Connection/Speed LED: |
|
Activity LED: |
|
|||||||
Speed LED |
|
|
|
Activity LED |
|
|
|||||||||||||
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
State |
Description |
|
State |
Description |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Orange |
1 Gbps data rate |
|
Blinking |
Data transmission or receiving is occurring |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Green |
100 Mbps data rate |
|
Off |
No data transmission or receiving is occurring |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Off |
10 Mbps data rate |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
LAN Port |
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
Line In Jack (Blue)
The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out Jack (Green)
The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.
(Note 1) The DVI-D port does not support D-Sub connection by adapter.
(Note 2) The resolution of 4096x2160 can be supported when using an FM2+ APU; the maximum resolution supported is 1920x1200 when using an FM2 APU.
•• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.
•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.
- 11 -