Geovision GV-BL5700 User Manual
GV-IP Camera
Hardware Manual
Bullet Camera
Ultra Bullet Camera
Target Bullet Camera
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ICH265HISIV10-A-EN
© 2016 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in
part, without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any
kind and assumes no responsibility for errors or omissions. No liability is
assumed for incidental or consequential damages arising from the use of
the information or products contained herein. Features and specifications
are subject to change without notice. Note: no memory card slot or local
storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows and Windows
XP are registered trademarks of Microsoft Corporation.
April, 2016
Contents
Note for Adjusting Focus and Zoom................................ii
Note for Installing Camera Outdoor................................iii
Note for Closing the Bullet Camera Cover .................... iv
Note for Silica Gel Bags .................................................. iv
Note for Waterproofing Failures...................................... v
Note for Recording .......................................................... vi
Chapter 1 Bullet Camera (Part I)......................................1
1.1 Packing List..............................................................................3
1.2 Features...................................................................................4
1.3 Overview ..................................................................................7
1.4 Installation................................................................................8
1.4.1 Connecting the Camera.................................................10
1.4.2 Adjusting the Angles......................................................15
1.4.3 Adjusting Lens and Inserting a Memory Card ................19
1.4.4 Installing the Sun-Shield Cover......................................22
1.5 Loading Factory Default..........................................................23
Chapter 2 Bullet Camera (Part II)...................................24
2.1 Packing List............................................................................26
2.2 Features.................................................................................27
2.3 Overview ................................................................................29
2.4 Installation..............................................................................31
2.5 Connecting the Camera..........................................................38
Chapter 3 Bullet Camera (Part III)...................................40
3.1 Packing List............................................................................41
3.2 Features..................................................................................42
3.3 Overview ................................................................................44
3.3 Overview ................................................................................44
3.4 Installation..............................................................................45
3.4.1 Adjusting the Angles......................................................49
3.4.2 Adjusting Lens...............................................................51
3.5 Connecting the Camera..........................................................52
3.5.1 Wire Definition...............................................................52
3.5.2. Power Connection.........................................................53
3.6 Loading Factory Default..........................................................55
Chapter 4 Ultra Bullet Camera .......................................56
4.1 Packing List............................................................................58
4.2 Features.................................................................................59
4.3 Overview ................................................................................61
4.4 Installation..............................................................................63
4.4.1 Waterproofin g th e Ca b l e................................................68
4.4.2 Connecting the Camera.................................................70
4.5 Loading Factory Default..........................................................73
Chapter 5 Target Bullet Camera (Part I)........................56
5.1 Packing List............................................................................57
5.2 Features.................................................................................58
5.3 Overview ................................................................................59
5.4 Installation..............................................................................60
5.5 Connecting the Camera...........................................................64
5.5.1 Wire Definition...............................................................64
5.5.2 Power Connection.........................................................65
5.6 Loading Factory Default..........................................................66
Chapter 6 Target Bullet Camera (Part II).......................67
6.1 Packing List............................................................................68
6.2 Features.................................................................................69
6.3 Overview ................................................................................70
6.4 Installation..............................................................................71
6.4.1 Adjusting the Angles......................................................76
6.4.2 Adjusting Lens...............................................................77
6.5 Connecting the Camera..........................................................78
6.5.1 Wire Definition...............................................................78
6.5.2 Power Connection.........................................................79
6.6 Loading Factory Default..........................................................79
Options
Optional devices can expand your camera’s capabilities and versatility.
Contact your dealer for more information.
Device Description
The power adapter is available for all Bullet Camera,
Power Adapter
GV-PA191 PoE
Adapter
GV-Relay V2
GV-POE Switch
GV-Mount
Accessories
Ultra Bullet Camera (except GV-BL2511-E / 5311-E),
and Target Bullet Camera. Contact your sales
representative for the countries and areas supported.
The GV-PA191 PoE adapter is designed to provide
power and network connection to the cameras over a
single Ethernet cable.
The GV-Relay V2 is designed to expand the voltage
load of GV IP devices. It provides 4 relay outputs, and
each can be set as normally open (NO) or normally
closed (NC) independently as per your requirement.
The GV-POE Switch is designed to provide power
along with network connection for IP devices. The
GV-POE Switch is available in various models with
different numbers and types of ports.
The GV-Mount Accessories provide a comprehensive
lineup of accessories for installation on ceiling, wall
corner and pole. For details, see GV-Mount
Accessories Installation Guide on the Software DVD.
i
Note for Adjusting Focus and Zoom
When adjusting the Focus and Zoom Screws on Bullet Camera, do not
over tighten the Focus and Zoom screws. The screws only need to be as
tight as your finger can do it. It is not necessary to use any tools to get
them tighter. Doing so can damage the structure of lens.
For example,
Zoom Screw
Focus Screw
The maximum torque value for all the zoom and focus screws is 0.049 N.m
ii
Note for Installing Camera Outdoor
When installing the cameras outdoor, be sure that:
1. The camera is set up above the junction box to prevent water from
entering the camera along the cables.
2. Any PoE, power, audio and I/O cables are waterproofed using
waterproof silicon rubber or the like.
iii
Note for Closing the Bullet Camera Cover
To ensure that the camera performs its full capacity against water and dust ,
tightly close and lock the camera cover as indicated below.
Note for Silica Gel Bags
1. The silica gel bag loses its effectiveness when the dry camera is
opened. To prevent the lens from fogging up, replace the silica gel
bag every time you open the camera, and conceal the gel bag in
camera within 2 minutes of exposing to open air.
2. When the camera is shipped, a silica gel bag will be included inside
the camera. For the first-time user, replace the silica gel bag prior to
the installation to avoid foggy live view.
iv
Note for Waterproofing Failures
To avoid waterproofing failures, do not open the screw on the camera body.
y The screw on Ultra Bullet
Camera
y The screw on Target Bullet
Camera
y The screw on GV-EBL2101 y The screw on GV-BL3700 /
5700
v
Note for Recording
1. By default, the images are recorded to the memory card inserted in
the GV-IP Camera (except GV-IR Arctic Box Camera and Target
Series, which are not equipped with a memory card slot). Make sure
the Write recording data into local storage option (see 4.1.1
Video Settings, GV-IPCam Firmware Manual) is enabled. If this
option is disabled, the camera will stop recording to the memory
card while the live view is accessed through Web browsers or other
applications.
2. Mind the following when using a memory card for recording:
y Recorded data on the memory card can be damaged or lost if
the data are accessed while the camera is under phys i cal shock,
power interruption, memory card detachment or when the
memory card reaches the end of its lifespan. No guarantee is
provided for such causes.
y The stored data can be lost if the memory card is not accessed
for a long period of time. Back up your data periodically if you
seldom access the memory card.
y Memory cards are expendable and their durability varies
according to the conditions of the installed site and how they are
used. Back up your data regularly and replace the memory card
annually.
y Replace the memory card when its read/write speed is lower
than 6 MB/s or when the memory card is frequently undetected
by the camera.
3. It is recommended to use memory cards of the following setting and
specifications:
y Apply a battery backup (UPS) to avoid power outage.
y Use Micro SD card of MLC NAND flash, Class 10 for better
performance.
vi
Bullet Camera (Part I)
1
Chapter 1 Bullet Camera (Part I)
The Bullet Cameras are specifically designed for outdoors and are
weatherproof (IP66 or IP67). They are equipped with IR LEDs for infrared
illumination in night vision applications. The models described in this
chapter use auto iris, which allows for automatic control of exposure.
The WDR Pro models enhance the image by processing contrasting
intensity of light. The super low lux models can produce color live view in
near darkness. The motorized varifocal lens models allow the user to
adjust the focus and zoom through the Web interface.
1
Model No. Specifications Description
GV-BL120D 1.3 MP, H.264, Low Lux
GV-BL130D 1.3 MP, H.264
GV-BL220D 2 MP, H.264
GV-BL320D 3 MP, H.264
GV-BL1500
GV-BL2400 2 MP, H.264, WDR Pro
GV-BL2500
GV-BL3400
GV-BL1210
GV-BL2410
GV-BL3410
GV-BL5310
Varifocal
lens
Motorized
varifocal
lens
Auto Iris, f: 3 ~ 9
mm, F/1.2, 1/2.7’’
ø 14 mm Lens
Mount
Auto Iris,
f: 3 ~ 9 mm,
F/1.2, 1/2.7’’
ø 14 mm Lens
Mount
Auto Iris,
f: 4.5 ~ 9 mm,
F/1.2, 1/2.7’’
ø 14 mm Lens
Mount
1.3 MP, H.264, Super
Low Lux
2 MP, H.264, Super Low
Lux
3 MP, H.264, WDR Pro
1.3 MP, H.264, Low Lux,
3X Optical Zoom
2 MP, H.264, WDR Pro,
3X Optical Zoom
3 MP, H.264, WDR Pro,
3X Optical Zoom
5 MP, H.264, 2X Optical
Zoom
2
Bullet Camera (Part I)
1
1.1 Packing List
y Bullet Camera
y Self Tapping Screw x 3
y Plastic Screw Anchor x 3
y Torx Wrench x 2
y Sun-Shield Cover Kit (Sun-Shield Cover, Philips Head Screw x 2,
Plastic Screw Spacer x 2 and Hexagon Screw x 2)
y Silica Gel Bag x 2
y 2-Pin Terminal Block
y Power Adapter
y GV-IPCAM Software DVD
y GV-NVR Softw a r e DVD
y Warranty Card
Note: The power adapter can be excluded upon request.
3
1.2 Features
y Image sensor
Camera Model Image Sensor
GV-BL120D / 1210 1/3’’ progressive scan low lux CMOS
GV-BL1500 / 1510
GV-BL130D / 220D / 320D
GV-BL5310
GV-BL2400 / 2410
GV-BL3400 / 3410
GV-BL2500 / 2510
y Dual streams from H.264 or MJPEG
y Frame rate
Camera Model Frame Rate
GV-BL120D / 130D
GV-BL1210
GV-BL1500 / 1510
GV-BL220D / 2400 / 2410
GV-BL2500 / 2510
GV-BL320D/ 3400 / 3410 20 fps at 2048 x 1536
GV-BL5310 10 fps at 2560 x 1920
y Day and night function (with removable IR-cut filter)
y Megapixel lens
y Motorized varifocal lens for remote focus/ zoom adj ustm ent
(GV-BL1210 / 1510 / 2410 / 2510 / 3410 / 5310 only)
y Wide Dynamic Range Pro (GV-BL2400 / 2410 / 3400 / 3410 only)
y Ingress protection
(IP66 for GV-BL120D / 130D / 220D / 320D)
1/3’’ progressive scan super low lux
CMOS
1/2.5’’ progressive scan CMOS
1/3.2’’ progressive scan CMOS
1/2.8’’ progressive scan super low
lux CMOS
30 fps at 1280 x 1024
30 fps at 1920 x 1080
4
Bullet Camera (Part I)
1
(IP67 for GV-BL1500 / 2400 / 2500 / 3400 and GV-BL1210 / 1510 /
2410 / 2510 / 3410 / 5310)
y Vandal resistance (IK10 for metal casing for all models except
GV-BL120D / 130D / 220D / 320D)
y Two-way audio
y One sensor input and alarm output
y Micro SD card slot (SD/SDHC) for local storage
y NAS recording
y Recording assigned by GV-Edge Recording Manager (Windows &
Mac)
y Cable-concealed bracket preventing cable from being cut
y DC 12V / AC 24V / PoE (IEEE 802.3af)
y Intelligent IR
y Maximum IR distance
Camera Model Maximum IR Distance
GV-BL120D / 130D / 220D / 320D 15 m (50 ft)
GV-BL1210 / 5310 40 m (131 ft)
GV-BL2400 / 2410
GV-BL2500 / 2510
GV-BL3400 / 3410
GV-BL1500 / 1510 70 m (230 ft)
y 3D noise reduction (GV-BL1500 / 1510 / 2500 / 2510 only)
y 2D noise reduction (for all models except super low lux models)
y Defog
y Motion detection
y Tampering alarm
y Visual automation
y Text overlay
y Privacy mask
y IP address filtering
50 m (164 ft)
5
y Smart Phone and 3GPP support
y 31 languages on Web interface
y ONVIF (Profile S) conformant
6
1.3 Overview
Bullet Camera (Part I)
1
1
Figure 1-1
No. Name Description
1 Memory Card Slot
2 Zoom S crew Hold s the zoom lens in place.
3 Focus Screw Holds the focus lens in place
4 Default Button
Receives a micr o SD card (SD/SDHC,
version 2.0 only, Class 10).
Resets all configurations to factory default.
For details, see 1.5 Loading Factory Default.
2 3 4
7
1.4 Installation
These instructions describe the basic installation of the Bullet Camera.
1. Slide the cable clamp to the camera base.
Cable Clamp
2. Install the Bullet Ca mera to the wall.
Figure 1-2
3. Remove the protection sticker from the camera’s cover
4. Connect the power, network and other wires to the Bullet Camera.
See 1.4.1 Connecting the Camera.
8
Figure 1-3
Bullet Camera (Part I)
1
5. Access the live view. For details, see 2.1. Accessing the Live View,
GV-IPCam Firmware Manual.
6. Adjust angles of the camera body based on the live view. Three
shafts can be adjusted. See 1.4.2 Adjusting the Angles.
7. Loosen the camera’s cover, adjust the focus of the camera and
optionally insert a micro SD card (SD/SDHC, version 2.0, Class 10)
into the SD card slot. See 1.4.3 Adjusting Lens and Inserting a
Memory Card.
8. Fasten the camera’s cover.
9. Install the sun-shield cover to the Bullet Camera. For details, see
1.4.4 Installing the Sun-Shield Cover.
9
1.4.1 Connecting the Camera
Wire Definition for Auto Iris Models
The 7-Pin Data Cable provides connections for power, ground, 1 sensor
input, 1 alarm output, audio input and audio output. The wires are
illustrated and defined below:
Digital In (Red)
DC 12V+ / AC 24V + (Brown)
Digital Out (Orange)
DC 12V- / AC 24V - (Black)
GND (Yellow)
Audio In (Red)
Ethernet (PoE)
Audio Out (Green)
Figure 1-4
No. Wire Color Definition
1 Red Digital In
2 Brown DC 12V+ / AC 24V+
3 Orange Digital Out
4 Black DC 12V- / AC 24V5 Yellow Ground
6 Red RCA Audio in
7 Green RCA Audio out
10
Bullet Camera (Part I)
1
Note that the Audio In and Out connectors may also come as terminal
blocks:
Digital In (Red)
DC 12V+ / AC 24V + (Brown)
Digital Out (Orange)
DC 12V- / AC 24V - (Black)
GND (Yellow)
Audio In (Brown)
Ethernet (PoE)
Audio Out (Green)
Figure 1-5
No. Wire Color Definition
1 Red Digital In
2 Brown DC 12V+ / AC 24V+
3 Orange Digital Out
4 Black DC 12V- / AC 24V5 Yellow Ground
6 Brown terminal block Audio in
7 Green terminal block Audio out
11
Power Connection
Use one of the following methods to supply power to the camera.
y Use a Power over Ethernet (PoE) adapter to connect the camera to
the network, and the power will be provided at the same time.
y Plug the power adaptor to the terminal block as shown below.
y Insert the black wire of the Bullet Camera to the left pin (+) and
the brown wire to the right pin (-).
Figure 1-6
y Connect the DC 12V Power Adapter to the Terminal Block.
Terminal Block
12
Figure 1-7
DC 12V Power Adaptor
2
Bullet Camera (Part I)
1
I/O Device Connection
The camera supports one digital input and one digital output of dry contact.
I/O
1
Figure 1-8
For details on how to enable an installed I/O device, see 4.2 I/O Settings,
GV-IPCam Firmware Manual.
Voltage Load Expansion (Optional)
The camera can only drive a maximum load of 200mA 5V DC. To expand
the maximum voltage load to 10A 250V AC, 10A 125V AC or 5A 100V DC,
connect the camera to a GV-Relay V2 module (optional product). Refer to
the figure and table below.
3
Output Devices
Pin Function
1 Digital Output
2 GND
3 Digital Input
Connect to Power
Figure 1-9
13
GV-Relay V2 Bullet Camera
COM Ground (Yellow)
DO1 Digital Out (Orange)
14
Bullet Camera (Part I)
1
1.4.2 Adjusting the Angles
The Bullet Camera is designed to be adjustable in three shafts for easy
and flexible installation.
First Shaft
You can adjust the camera body by 360 degrees to the right or the left.
1. Unscrew the panning lock screw with the torx wrench.
Panning Lock Screw
Torx Wrench
2. Adjust the angle of camera body to the right or the left, and fasten
the panning lock screw.
Figure 1-10
0 ~ 360°
Figure 1-11
15
Second Shaft
You can adjust the camera body up and down by 90, 112.5, 135, 157.5 or
180 degrees by using the gears inside the camera body and the camera
base.
1. Unscrew the tilting lock screw with the torx wrench.
Tilting Lock Screw
Torx Wrench
Figure 1-12
2. Hold the camera body, and move the camera base to the right to
separate the camera gears.
Move the Camera
Base to the Right
Camera Body
Camera Gears
Figure 1-13
16
Bullet Camera (Part I)
1
3. Adjust the angle of camera body to 90°, 112.5°, 135°, 157.5° or 180°.
Then move the camera base to the left to combine the gears.
180°
157.5°
135°
112.5°
90°
4. Fasten the tilting lock screw.
Third Shaft
You can adjust the camera base by 360°.
1. Unscrew the base fixing screw with the torx wrench.
Figure 1-14
Torx Wrench
Base Fixing Scre w
Figure 1-15
17
2. Adjust the angle of camera base, and fasten the base fixing screw.
0~360°
Figure 1-16
18
Bullet Camera (Part I)
1
1.4.3 Adjusting Lens and Inserting a Memory Card
To adjust the camera’s zoom and focus or to insert a micro SD card
(SD/SDHC, version 2.0 only, Class 10), follow the steps bel ow.
1. Loosen the camera’s cover.
Camera’s Cover
Figure 1-17
For GV-BL2511-E / 5311-E, loosen the camera’s cover and the screw
as indicated below.
Figure 1-18
19
Loading...