GE Industrial Solutions SE, SF, TE, TF, TQ User Manual

...

quip

DEH042 Installation Instructions R03

Spectra Series™ Power Panelboards

Circuit Breaker Cover

WARNING: Danger of electrical shock or injury. Turn

OFF

switchboard before workin

ment or removing any component. Do

e not remove circuit

ower ahead of the panelboard or

inside the

rotective devices or an other component until the power is turned OFF.

General

These instructions apply to the following circuit breaker frames: SE, SF, TE, TF, TQ, and TEL.

Installation

1. Select the breaker cover supports and breaker covers.

Table 1 lists the catalog numbers of the appropriate cover supports for various switchboard and panelboard sizes. Table 2 lists the breaker covers for various breaker types.

Switchboard or Panelboard Width

Cover Height

41/8" (3X) &

/2" (4X)

23/4" (2X) 208C1850P6 208C1850P5 208C1850P5

• Use 208C1850P3 for SFHA, SFLA, SFPA, TFL, TFJ, TFK, and THFK, in single-branch mountings.

27 & 31" Pnlbd

35" Swbd

208C1850P4* 208C1850P3 208C1850P3

Table 1. Circuit breaker cover support catalog numbers for various

panelboard and switchboard widths.

Switchboard or Panelboard Width

Cover Height

SEDA, SEHA, SELA, SEPA – Double-branch mount only 41/8" (3X) 208C4262G32 208C4262G33 208C4262G34 51/2" (4X) N/A 208C4262G35 208C4262G36

SFHA, SFLA, SFPA – Single-branch mount (see Figure 1) 41/8" (3X) 208C4262G53 208C4262G54 208C4262G55 51/2" (4X) N/A 208C4262G56 208C4262G57

41/8" (3X) 208C4262G58 208C4262G59 208C4262G60

51/2" (4X) N/A 208C4262G61 208C4262G62

23/4" (2X) 208C4262G26 208C4262G27 208C4262G28 41/8" (3X) 208C4262G29 208C4262G30 208C4262G31

TFJ, TFK, THFK, TFL – Single-branch mount (see Figure 1)

41/8" (3X) 208C4262G1 208C4262G2 208C4262G3

41/8" (3X) N/A 208C4262G6 208C4262G7

23/4" (2X) 208C4262G20 208C4262G21 208C4262G22 41/8" (3X) 208C4262G23 208C4262G24 208C4262G25

27 & 31" Pnlbd

35" Swbd

SFHA, SFLA, SFPA – Double-branch mount

TEB, TED, THED, TEL – Double-branch mount

TFJ, TFK, THFK, TFL – Double-branch mount

TQD, THQD – Double-branch mount

Table 2. Circuit breaker cover catalog numbers for various

panelboard and switchboard widths.

36 & 40" Pnlbd

40" Swbd

36 & 40" Pnlbd

40" Swbd

44" Pnlbd 45" Swbd

2. Mount the circuit breaker cover supports. Mount the breaker cover supports supplied in the kit to the circuit breaker module or mounting plate, according to the instructions supplied with the module or mounting plate. To install the cover support for single-branch SF and TF breakers, first remove the breaker mounting bracket by prying back the plastic spring clip on the module. Slide the cover support on and snap the breaker mounting bracket back into the module. Fasten the cover support to the module, as shown in Figure 1.

Breaker

Mounting

Bracket

Cover

Support

Figure 1. Installing the cover support for single-branch SF and TF

breakers.

3. Attach the center barrier to the breaker cover for double-branch 3X or 4X TEB, TED, THED, TQD, THQD, SE, SF, TFK, THFK, and TFL breakers. Use two push-in rivets, as shown in Figure 2.

Figure 2. Attaching the center barrier to the breaker cover.

4. Install the space fillers to any holes in the filler plate

quip

with no breakers mounted behind.

For SE, SF, TFJ, TFK, THFK, and TFL breakers, use

the steel space filler and two #10 x

/8" screws, tightened to 25 in-lb, as shown in Figure 3. For TEB, TED, THED, TQD, THQD, and TEL breakers, use the plastic space fillers. Install the filler from the underside of the breaker cover. Engage the slotted end of the space filler with the inside edge of the opening in the breaker cover. Secure the other end in place with a #10 x

/8" screw, tightened to 15

in-lb, as shown in Figure 4.

5. Install the assembled breaker cover over the flexible prongs on the filler supports, as shown in Figures 5 and 6.

Figure 5. Breaker cover installed on the filler supports for SE, SF, TFJ,

TFK, THFK, and TFL breakers.

Figure 6. Breaker cover installed on the filler supports for TEB, TED,

THED, TQD, THQD, and TEL breakers.

Figure 3. Installing the steel space filler for SE, SF, TFJ, TFK, THFK,

and TFL breakers.

Figure 4. Installing the plastic space fillers for TEB, TED, THED, TQD,

THQD, and TEL breakers.

These instructions do not cover all details or variations in e

ment nor do they provide for every possible contingency that

be met in connection with installation, operation, or

maintenance. Should further information be desired or should

articular problems arise that are not covered sufficiently for the urchaser’s purposes, the matter should be referred to the GE

Company.

CAUTION: To ensure secure mounting, push the breaker cover completely over the four flexible prongs on top of the filler supports, as shown in Figure 7.

Figure 7. Breaker cover securely mounted on the flexible prongs.

NOTE: Push-on breaker covers may bend if not removed properly. Pull the upper edge of the breaker cover off the flexible prongs, then pull the lower edge free.

GE Industrial Systems

General Electric Company 41 Woodford Ave., Plainville, CT 06062