GE Industrial Solutions KSTW010A0A User Manual

GE

t

Data Sheet

KSTW010A0A Barracuda™ Series; DC-DC Converter Power Modules

36-75Vdc Input; 5.0Vdc, 10A Output

RoHS Complian

Applications

 Wireless Networks

 Hybrid power architectures

 Optical and Access Network Equipment

 Enterprise Networks including Power over Ethernet (PoE)

 Industrial markets

Options

 Negative Remote On/Off logic (preferred)

 Surface Mount/Tape and Reel (-SR Suffix)

 Auto-restart Over current/Over voltage protections

(preferred)

 Shorter through hole pin trim

Features

 Compliant to RoHS II EU “Directive 2011/65/EU (-Z versions)

 Compliant to REACH Directive (EC) No 1907/2006

 Wide Input Voltage Range, 36V

 No minimum load

 High efficiency – 91% at full load (V

 Constant switching frequency

 Low output ripple and noise

 Small Size and low profile, follows DOSA standard 1/16th

footprint

33.0 mm x 22.9 mm x 9.3 mm
(1.30 in x 0.9 in x 0.37 in)

 Surface mount (SMT) or Through hole (TH)

 Reflow process compliant, both SMT and TH versions

 Positive Remote On/Off logic

 Output overcurrent/voltage protection (hiccup)

 Over-temperature protection

 Output Voltage adjust: 80% to 110% of V

 Wide operating temperature range (-40°C to 85°C)

 UL*Recognized to UL60950-1, CAN/CSA

and EN60950-1(VDE

‡

0805-1) Licensed

 CE mark meets 2006/95/EC directive

 Meets the voltage and current requirements for ETSI 300-

132-2 and complies with and licensed for Basic insulation
rating per EN60950-1

 2250 Vdc Isolation tested in compliance with IEEE 802.3

PoE standards

 ISO** 9001 and ISO 14001 certified manufacturing facilities

to 75Vdc

dc

IN

=48Vdc)

o,nom

†

C22.2 No.60950-1,

§

¤

Description

The KSTW010A0A series power modules are isolated DOSA compliant 1/16th brick dc-dc converters that operate over a wide input
voltage range of 36 V
the input, allowing versatile polarity configurations and grounding connections. The modules exhibit high efficiency of 91% typical
at full load. Built-in filtering for both input and output minimizes the need for external filtering. The module is fully self-protected
with output over-current and over-voltage, over-temperature and input under voltage shutdown control. Optional features include
negative or positive on/off logic and SMT connections.

* UL is a registered trademark of Underwriters Laboratories, Inc.

†

CSA is a registered trademark of Canadian Standards Association.

‡

VDE is a trademark of Verband Deutscher Elektrotechniker e.V.

§ This product is intended for integration into end-user equipment. All of the required procedures of end-use equipment should be followed.
¤ IEEE and 802 are registered trademarks of the Institute of Electrical and Electronics Engineers, Incorporated.
** ISO is a registered trademark of the International Organization of Standards.

-75Vdc and provide a single precisely regulated output voltage at 5.0Vdc. The output is fully isolated from

dc

April 1, 2013 ©2012 General Electric Company. All rights reserved. Page 1

GE

Data Sheet

KSTW010A0A Barracuda™ Series; DC-DC Converter Power Modules

36-75Vdc Input; 5.0Vdc, 10A Output

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings
only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations
sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability.

Parameter Device Symbol Min Max Unit

Input Voltage (Continuous) All V

Transient (100ms) All V

Operating Ambient Temperature All T

(see Thermal Considerations section)

Storage Temperature All T

I/O Isolation Voltage (100% factory Hi-Pot tested) All

IN

IN, trans

A

stg

 

Electrical Specifications

Unless otherwise indicated, specifications apply at VIN = 48Vdc, resistive load, and TA = 25°C conditions.

Parameter Device Symbol Min Typ Max Unit

Operating Input Voltage All VIN 36 48 75 Vdc

Input No Load Current

(VIN = 48Vdc IO = 0A, module enabled)

Input Stand-by Current

(VIN = 48Vdc, module disabled)

Maximum Input Current (VIN=36Vdc, IO= I

Inrush Transient All I2t 0.05 A2s

Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 12μH source impedance; V
see Test configuration section)

Input Ripple Rejection (120Hz) All 60 dB

) All I

O,MAX

=0V to 75Vdc, IO= I

IN

Omax

;

All I

All I

All 30 mA

IN,No load

6 8 mA

IN,stand-by

IN, MAX

-0.3 80 Vdc

-0.3 100 Vdc

-40 85 °C

-55 125 °C

2250 Vdc

40 50 mA

1.6 Adc

p-p

EMC, EN55022 See EMC Considerations section

CAUTION: This power module is not internally fused. An input line fuse must always be used.

This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of
complex power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety
and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6A
(see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input
current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information.

April 1, 2013 ©2012 General Electric Company. All rights reserved. Page 2

GE

Data Sheet

KSTW010A0A Barracuda™ Series; DC-DC Converter Power Modules

36-75Vdc Input; 5.0Vdc, 10A Output

Electrical Specifications (continued)

Unless otherwise indicated, specifications apply at VIN = 48Vdc, resistive load, and TA = 25°C conditions.

Parameter Device Symbol Min Typ Max Unit

Output Voltage Set-point

=48Vdc, IO=I

(V

IN

O, max

,)

All V

O, set

Output Voltage

(Over all operating input voltage, resistive load, and temperature

All V

O

conditions until end of life)
Adjustment Range
Selected by external resistor
Remote Sense Range
Output Regulation

Line (VIN=V

Load (IO=I

Temperature (T

IN, min

O, min

to V

) All

IN, max

to I

) All

O, max

to T

ref=TA, min

) All

A, max

Output Ripple and Noise on nominal output

All V

All

O, adj

+10 % V

Measured with 10uF Tantalum||1uF ceramic

(VIN=48Vdc, IO=80%I

RMS (5Hz to 20MHz bandwidth)

Peak-to-Peak (5Hz to 20MHz bandwidth)
External Capacitance (see Note 1 in Feature Specifications) All C
Output Current
(VIN =36V to 75V) All I

Output Current Limit Inception (Hiccup Mode)
(VIN =36V to 75V) All I

Output Short-Circuit Current (VO ≤ 250 mV) All I

Efficiency (VIN=48Vdc, IO=I

Switching Frequency (Fixed)
VIN=48Vdc, IO= I

O, max

)

O, max

All

) All η 90.0 91.0

O, max

All f

O, max

o

O, lim

O, s/c

sw

Dynamic Load Response
(Io/t=0.1A/s)

Load Change from Io= 50% to 75% or 25% to 50% of I

:

o,max

Peak Deviation All Vpk

Settling Time (Vo<10% peak deviation) All ts

4.93 5.00 5.07 Vdc

-3.0

-20



 




0



0.05 0.2 % V

0.05 0.2 % V

10 25 mV
60 75 mV


+3.0 % V

+10 % V

1.0 % V

5000 μF

O, set

O, set

O, set

O, set

O, set

O, set

rms

pk-pk

0



10.0 Adc

11










2.5

350

3.0

400

14 Adc








A

%

kHz

% V

 s

rms

O, set

Isolation Specifications

Parameter Symbol Min Typ Max Unit

Isolation Capacitance C

Isolation Resistance R

I/O Isolation Voltage All

iso

iso



10

 

1000

 



2250 Vdc

April 1, 2013 ©2012 General Electric Company. All rights reserved. Page 3

pF

MΩ

GE

Data Sheet

KSTW010A0A Barracuda™ Series; DC-DC Converter Power Modules

36-75Vdc Input; 5.0Vdc, 10A Output

General Specifications

Parameter

Calculated Reliability based upon Telcordia SR-332 Issue 2: Method I Case 3
(I

O

=80%I

, TA=40°C, airflow = 200 lfm, 90% confidence)

O, max

Weight

FIT 272.0 10

MTBF 3,677,136 Hours

Min Typ Max Unit

9

/Hours



13 (0.46)



g (oz.)

Feature Specifications

Unless otherwise indicated, specifications apply at VIN = 48Vdc, resistive load, and TA = 25°C conditions. See Feature Descriptions for
additional information.

Parameter Device Symbol Min Typ Max Unit

Remote On/Off Signal Interface

(VIN=V

Signal referenced to V

Negative Logic: device code suffix “1”

Logic Low = module On, Logic High = module Off

Positive Logic: No device code suffix required

Logic Low = module Off, Logic High = module On

Turn-On Delay and Rise Times

(IO=80% of I

Case 1: Input power is applied for at least 1second, and then the
On/Off input is set from OFF to ON (T
V

O

to V

IN, min

Logic Low - Remote On/Off Current (V

; open collector or equivalent,

IN, max

terminal)

IN-

= -0.7Vdc) All I

on/off

Logic Low - On/Off Voltage All V

Logic High Voltage (I

= 0Adc) All V

on/off

Logic High maximum allowable leakage current All I

)

O, max

= 10% of V

O, set

= on/off pin transition until

delay

)

All

on/off

on/off

on/off

on/off

T

Case1

delay

 

-0.7

2.4

 



0.15 mA




0.8 Vdc

7 Vdc

25 μA

25 50 ms

Case 2: On/Off input is set to Module ON, and then input power is

applied

= VIN reaches V

(T

delay

until VO = 10% of V

IN, min

O,set

)

Output voltage Rise time (time for Vo to rise from 10%
of V

to 90% of V

o,set

o, set

)

All

All T

Output Voltage Overshoot

(IO=80% of I

Output Overvoltage Protection

, VIN= 48Vdc)

O, max

All V

Input Undervoltage Lockout

Turn-on Threshold All V

Turn-off Threshold All V

Hysterisis All V

T

delay

Case2

O, limit

uv/on

uv/off

rise

hyst





6.0



30 32



35 50 ms

5 10 ms

Vdc

Vdc

O, set

dc

3 % V



7.0 Vdc

34 36 V



2.0



Note: 1.The module requires a minimum of 680 μF external output capacitor to avoid exceeding the OVP maximum limits during startup into open
loop fault conditions.

April 1, 2013 ©2012 General Electric Company. All rights reserved. Page 4

G

K

3

A

C

T

p

On/Off

VOLTAGE

OUTPUT

VOLTAGE

E

n

s

a

v

i

c

a

d

s

O

U

n

M

s

4

a

t

2

A

t

O

s

e

e

v

C

A

A

e

e

g

e

r

e

r

o

a

e

u

L

t

5

0

%

1

n

h

c

m

V

5

=

Data S

eet

STW01

6-75Vdc I

haracteri

he following fi
ositive or neg

EFFICIENCY,  (%)

Figure 1. Con

0A0A B

put; 5.0V

tic Curve

gures provide

tive remote

OUTP

verter Efficie

rracud

c, 10A Ou

typical charac

n/Off logic.

T CURRENT, IO (

cy versus Ou

™ Serie

put

teristics for th

)

put Current.

; DC-D

KSTW010A0

Figur

(A)

IN

INPUT CURRENT, I

(V) (100mV/div)

O

Conve

(5.0V, 10A) at

2. Converte

ter Pow

25oC. The fig

INPUT VO

Input Curren

r Modu

res are identi

TAGE, VIN (V)

versus Input

les

al for either

Voltage.

(V) (50mV/div)

O

V

OUTPUT VOLTAGE

Figure 3. Typ

( (V) (2V/div)

O

V) (2V/div) V

On/Off

V

Figure 5.Typi
logic version

cal output rip

TI

al Start-up U

shown (VIN =

TI

ME, t (2s/div)

ple and noise

E, t (10ms/div)

ing Remote

8V, Io = I

o,max

(Io = I

)

.

o,max

).

n/Off, negati

OUTPUT CURRENT OUTPUT VOLTAGE

Figur
Chan

INPUT VOLTAGE OUTPUT VOLTAGE

e Figur

I

o,max

Io(A) (2A/div) V

4. Transient
e from 50% t

(V) (2V/div)

O

(V) (20V/div) V

IN

V

6. Typical St

).

TIME, t (

Response to

75% to 50

TIME, t (

rt-up Using I

00s/div)

.1A/µS Dyna
of full load,

0ms/div)

put Voltage (

ic Load

in=48V.

V

IN

= 48V, I

o

pril 1, 2013

©

012 General El

ctric Company.

ll rights reserv

d.

Page