Geemarc AMPLICALL 10 Installation Manual

1

Description

DESCRIPTION

FRONT

Strobe flasher

Volume control

Tone control

Speaker

Alarm mode
switch

Low battery indicator
(Red LED)

Table mounting

Modular

j

ack PTT line

Wall mounting
screw holes

Shaker jack

Adaptor jack
(option)

Modular jack PTT line o

r

for a second Amplicall10
connection

batteries
compartment
(4 X AA)

REAR

2

Installation (See drawing)

1 - Insert the 4 battery type AA in the compartment .
2 - Connect the telephone line cord of you phone at the

Amplicall 10.

3 - Connect the RJ11 to RJ11 cable betwee n the

Amplicall and phone

4 - Connect the adaptor (option).

INSTALLATION

AC adaptor (option)

230V

UK plug

Telephone
plug

Option: Shaker

(ref.:SHAKCL_BLK)

3

Electrical connection : The apparatus is design ed to

operate from a 230V 50Hz supply only. (Classified as
«hazardous voltage» according to EN60950 standard).
The apparatus does not incorporate an integral power
on/off switch. To disconnect the power, either switch off
supply at the mains power socket or unplug the AC
adaptor. When installing the apparatus, ensure that the
mains power socket is readily accessible.

Telephone connection : Voltages present on the
telecommunication network are classified TNV-3
(Telecommunication Network Voltage) according to the
EN60950 standard.

INSTALLATION

4

Alarm Operation

1 - SETTING THE ALARM MODE

Choose which alarm mode you would like, by moving the
alarm mode switch to one of the following positions :

0 : no alarm

: both strobe flasher and sound alarm selected
: both strobe flasher and shaker (if connected)

selected.
: both sound alarm and shaker (if connected)
selected.

2 - VOLUME CONTROL SLIDE SWITCH

Set the volume of the alarm sound or power on/off.

3 - TONE CONTROL SWITCH (3 POSITIONS)

Set the tone of the alarm sound.

INSTALLATION

5

Wall Mounting

1. Drill two holes horizontally, 96mm apart, and leave the
screws protruding from the wall by 5mm.

2. Hang the base on to the two screws and pull the base
down to lock it into place.

Table Mounting

If you want to mount the u nit on th e table, put into the base
cradle, and then plac e the base cradle on the tabl e.

Change The Battery

The unit requires 4×AA batteries

1. Open the battery door.

2. Insert four AA batteries into the compartment.

3. Snap the battery compartment door back into place.

Note: when the red indicator keep flashes,this indicates
battery low, to indicate the batteries need replacing.
During replacement of the batteries, disconnect all
telephone line cords from the wall modular jacks.

You can add one adaptor in option (contact 01 707-

384438)

INSTALLATION

6

Trouble shooting

Symptom Solution

No incoming call, it
rings automatically or
rings continuously; the
shaker vibrates
automatically or
continuously; the
camera LED flashes
automatically.

1) Check if the batteries
contact well.

2) Check if the power
adaptor connects
normally.

3) Turn off the power
switch for 10 minutes
and then turn it on.

When the power supply
works normally, the red
low battery LED flashes
automatically.

1) Check if it is low
battery.

2) Turn off the power
using the power off
switch for 10 minutes
and then turn back on.

When it is connected to
the power adaptor or 4
batteries have been
inserted, however,
when there is an
incoming call, no rings.

1) Check if it is connected
to the power adaptor
correctly.

2) Check if the batteries
are installed correctly.

3) Check if the volume
switch is turned on.

4) Check the line cord is
connected properly.

INSTALLATION

7

When it is connected to
the power adaptor or 4
batteries have been
installed , bell rings
normally, or camera
LED blinks normally,
when there is an
incoming call, but the
shaker doesn’t vibrate.

1) Check if it is connected
to the shaker correctly.

2) Check if the shaker
socket has been
damaged.

3) Check if the alarm
mode selection switch
position is correct.

INSTALLATION

8

From the moment your Geemarc product is purchased,
Geemarc guarantee it for the pe riod of on e year. During
this time, all repairs or replacements (at our option) are
free of charge. Should you experience a problem then
contact our helpline or visit our website at
www.geemarc.com

. The guarantee does not cover
accidents, negligence or breakages to any parts. The
product must not be tampered with or taken apart by
anyone who is not an authorised Geemarc
representative.The Geemarc guarantee in no way limits
your legal rights.

IMPORTANT: YOUR RECEIPT IS PART OF YOUR
GUARANTEE AND MUST BE RETAINED AND
PRODUCEDIN THE EVENT OF A WARRANTY CLAIM

Please note : The guarantee applies to the United
Kingdom only.

Declaration : Hereby Geemarc Telecom SA declares
that this product is in compliance with the essential
requirements and other relevant provisions of the Radio
and Telecommunications Terminal Equipment Directive
1999/5/EEC and in particular article 3 section 1a, 1b and
section 3.

The declaration of conformity may be consulted at
www.geemarc.com

GARANTIE

9

Recycling directives : The WEEE (Waste Electrical and

Electronic Equipment) has been put in place for the
products so at the end of their useful life are recycled i n
the best way.When this product is finished with, please
do not put it in your domestic waste bin.Please use one
of the following disposal options:

- Remove the batteries and deposit them in an
appropriate WEEE skip. Deposit the product in an
appropriate WEEE skip.

- Or, hand the old product to the retailer. If you purchase
a new one, they should accept it. Thus if you respect
these instructions you ensure human health and
environmental protection.

For product support and help visit our website

at www.geemarc.com

Telephone [phone]

Or fax [phone]

GARANTIE