Garmin Edge 500 User Manual

owner’s manual

EDGE® 500

GPS-ENABLED CYCLING COMPUTER

© 2010 Garmin Ltd. or its subsidiaries

Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062,
USA
Tel. [phone] or
[phone]
Fax [phone]

Garmin (Europe) Ltd.
Liberty House,
Hounsdown Business Park,
Southampton, Hampshire, SO40 9LR UK
Tel. [phone] (outside the UK)
0808 2380000 (within the UK)
Fax [phone]

Garmin Corporation
No. 68, Jangshu 2nd Road,
Sijhih, Taipei County,
Taiwan
Tel. [phone]
Fax [phone]

All rights reserved. Except as expressly provided
herein, no part of this manual may be reproduced,
copied, transmitted, disseminated, downloaded
or stored in any storage medium, for any purpose
without the express prior written consent of Garmin.
Garmin hereby grants permission to download a
single copy of this manual onto a hard drive or
other electronic storage medium to be viewed and
to print one copy of this manual or of any revision
hereto, provided that such electronic or printed copy
of this manual must contain the complete text of
this copyright notice and provided further that any
unauthorized commercial distribution of this manual
or any revision hereto is strictly prohibited.

Information in this document is subject to change
without notice. Garmin reserves the right to change
or improve its products and to make changes in the
content without obligation to notify any person or
organization of such changes or improvements. Visit
the Garmin Web site (www.garmin.com) for current
updates and supplemental information concerning
the use and operation of this and other Garmin
products.

April 2010 Part Number 190-01071-00 Rev. B Printed in Taiwan

Garmin®, Garmin Training Center®, Auto Pause®,
Auto Lap®, Virtual Partner®, Edge®, are trademarks
of Garmin Ltd. or its subsidiaries, registered in
the USA and other countries. Garmin Connect™,
GSC™10, ANT™, and ANT+™ are trademarks of
Garmin Ltd. or its subsidiaries. These trademarks
may not be used without the express permission of
Garmin.

Windows® is a registered trademark of Microsoft
Corporation in the United States and/or other
countries. Mac® is a registered trademark of Apple
Computer, Inc. Firstbeat and Analyzed by Firstbeat
are registered or unregistered trademarks of Firstbeat
Technologies Ltd. Other trademarks and trade names
are those of their respective owners.

Table of Contents

Getting Started .................... 1

About the Battery ....................... 1

Installing the Edge ..................... 2

Turning on the Edge .................. 4

Acquiring Satellite Signals ......... 6

Optional ANT+ Sensors ............. 6

Going for a Ride ........................ 7

Saving Your Ride Data .............. 7

Using Free Software .................. 7

Transferring History to Your

Computer ............................... 8

Training with Your Edge ..... 9

Alerts ......................................... 9

Using Auto Lap by Distance .... 10

Using Auto Lap by Position.......11

Using Auto Pause .................... 12

Using Auto Scroll ..................... 12

Courses ................................... 13

Workouts ................................. 16

ANT+ Sensors ................... 20

Tips for Pairing ANT+ Sensors

with Your Garmin Device ....... 20

Putting on the Heart Rate

Monitor .................................. 21

Using the Heart Rate Monitor .. 22

Heart Rate Zones .................... 23

Replacing the Heart Rate

Monitor Battery ...................... 24

Installing the GSC 10............... 25

Using the GSC 10.................... 28

Replacing the GSC 10

Battery ................................... 29

Third-Party ANT+ Sensors ...... 30

ANT+ Sensor

Troubleshooting .................... 31

History ............................... 33

Viewing History ........................ 33

Viewing Distance and Time

Totals ..................................... 34

Deleting History ....................... 34

Data Recording........................ 34

Edge 500 Owner’s Manual iii

Data Management ............. 35

Connecting the USB Cable ..... 35

Loading Files ........................... 35

Deleting Files ........................... 36

Settings ............................. 37

Customizing Your Data

Fields .................................... 37

Data Fields .............................. 38

Changing Your System

Settings ................................. 41

Changing Your User Prole

Settings ................................. 43

Updating Your Bike Prole ....... 43

Switching Bikes ....................... 44

Changing the Start Notice ....... 44

Speed Zones ........................... 44

GPS Settings ........................... 45

Setting Elevation Points........... 46

Appendix ........................... 47

Registering Your Device .......... 47

About the Edge ........................ 47

Updating the Software ............. 47

Contacting Garmin Product

Support ................................. 47

Using the Backlight .................. 48

Buying Optional Accessories ... 48

Specications .......................... 48

Wheel Size and

Circumference ....................... 51

Activity Classes ....................... 53

Troubleshooting ....................... 54

Index .................................. 56

iv Edge 500 Owner’s Manual

Getting Started



WARNING

Always consult your physician before
you begin or modify any exercise
program. See the Important Safety
and Product Information guide in the
product box for product warnings and
other important information.

When using your Edge® the rst time,
complete the following tasks:

1. Charge the Edge (page 2).

2. Install the Edge (page 2).

3. Turn on the Edge (page 4).

4. Acquire satellites (page 6).

5. Set up optional ANT+™ sensors
(page 6).

6. Go for a ride (page 7).

7. Save your ride (page 7).

Getting Started

8. Get Garmin Connect™ or Garmin
Training Center® software
(page 7).

9. Transfer history to your computer
(page 8).

About the Battery



WARNING

This product contains a lithium-ion
battery. See the Important Safety and
Product Information guide in the
product box for product warnings and
other important information.

The Edge is powered by a built-in,
lithium-ion battery that you can
recharge using the AC charger or the
USB cable included in the product box.

NOTE: The Edge will not charge when
outside the temperature range of 32°F
to 122°F (0°C to 50°C).

Edge 500 Owner’s Manual 1

Getting Started

Charging the Edge

notice

To prevent corrosion, thoroughly
dry the mini-USB port, the weather
cap, and the surrounding area before
charging or connecting to a computer.

1. Plug the AC charger into a standard
wall outlet.

2. Pull up the weather cap from the
mini-USB port.

Tabs

Mini-USB port under
the weather cap

3. Plug the small end of the AC
charger into the mini-USB port.

To connect the Edge to your
computer using the USB cable, see

page 8.

4. Charge the Edge for at least three
hours before you begin using it.

A fully charged battery can run for up
to 18 hours before it must be recharged.

Installing the Edge

For the best GPS reception, position
the bike mount so the front of the
Edge is oriented toward the sky. You
can install the bike mount on the stem
(shown on page 3) or the handlebars.

1. Select a suitable and secure location
to mount the Edge where it does not
interfere with safe operation of your
bike.

2 Edge 500 Owner’s Manual

2. Place the rubber disk on the back of

5. Align the tabs on the back of the

the bike mount.

The rubber tabs align with the back

6. Press down slightly and turn the

of the bike mount so it stays in
place.

3. Place the bike mount on the bike
stem.

4. Attach the bike mount securely
using the two bands.

Getting Started

Edge with the bike mount notches.

Edge clockwise until it locks into
place.

Rubber

disk

Bike mount

notches

Edge Mounted on the

Bike Stem

Releasing the Edge

1. Turn the Edge clockwise to unlock
the device.

Bands around

the bike stem

Edge 500 Owner’s Manual 3

2. Lift the Edge off the mount.

Getting Started

Turning on the Edge

Press and hold POWER to turn on
the Edge.

Conguring the Edge

The rst time you turn on the Edge,
you are prompted to congure system
settings and user prole settings.

Follow the on-screen instructions

•
to complete the initial setup.

Press ▼ or ▲ to view choices

•
and change the default selection.

Press ENTER to make a selection.

•

Icons

Battery charge level

GPS is on and receiving
signals.

GPS is turned off.

Heart rate monitor is active.

Speed and cadence sensor
is active.

Power meter is active.

4 Edge 500 Owner’s Manual

Buttons

Each Edge button has multiple
functions.

Button Description

POWER/
LIGHT

BACK Press BACK to cancel

Press and hold POWER
to turn the device on
and off.

Press LIGHT to activate
the backlight. Press any
button to extend the
backlight for 15 seconds.

or return to the previous
menu.

Getting Started

START/
STOP

▼▲

LAP/RESET Press LAP to create a

PAGE/
MENU

ENTER Press ENTER to select

Press START/STOP to
start and stop the timer.

Press ▼ or ▲ to select
menus and settings.

Press and hold ▼ or ▲
to scroll quickly through
settings.

new lap.
Press and hold RESET to

reset the timer.

Press PAGE to scroll
through training data
pages.

Press and hold MENU to
switch between menu and
timer modes.

options and acknowledge
messages.

Edge 500 Owner’s Manual 5

Getting Started

Acquiring Satellite Signals

It may take 30 to 60 seconds to acquire
signals.

1. Go outdoors to an open area.

2. Make sure that the front of the Edge
is oriented toward the sky.

3. Wait while the Edge searches for
satellites.

Do not begin moving until the
locating satellite page disappears.

NOTE: To turn off the GPS receiver
and use the Edge indoors, see

page 45.

Optional ANT+ Sensors

NOTE: If you do not need to set up
ANT+ sensors, you can skip this step.

To use an ANT+ sensor during your
ride, you must install it and pair it with
the Edge.

•

•

•

For heart rate monitor instructions,
see page 21.

For GSC™ 10 speed and cadence
sensor instructions, see page 25.

For third-party ANT+ sensors, see

page 30, refer to the manufacturer’s

instructions, and go to

www.garmin.com/intosports.

6 Edge 500 Owner’s Manual

Going for a Ride

Before you can record history, you
must acquire satellite signals
(page 6).

1. Press and hold MENU to view the

timer page.

2. Press START to start the timer.

History is only recorded while the
timer is running.

3. After completing your ride, press

STOP.

Getting Started

Saving Your Ride Data

Press and hold RESET to save
your ride data and reset the timer.

Using Free Software

Garmin provides two software options
for storing and analyzing your ride
data:

Garmin Connect is Web-based

•
software.

Garmin Training Center is

•
computer software that does
not require the Internet after
installation.

1. Go to www.garmin.com

/intosports.

2. Follow the on-screen instructions
to install the software.

Edge 500 Owner’s Manual 7

Getting Started

Transferring History to Your Computer

1. Connect the USB cable to a USB
port on your computer.

2. Pull up the weather cap from the
mini-USB port.

Mini-USB port
under weather cap

3. Plug the small end of the USB
cable into the mini-USB port.

4. Open

Garmin Connect
(http://connect.garmin.com), or
open Garmin Training Center.

5. Follow the instructions included
with the software.

8 Edge 500 Owner’s Manual

Training with Your

Edge

Alerts

You can use Edge alerts to train toward

specic time, distance, calorie, heart

rate, cadence, and power goals.

Using Time, Distance, and
Calorie Alerts

1. Press and hold MENU.

2. Select Training > Alerts.

3. Select Time Alert, Distance Alert,
or Calorie Alert.

4. Turn on the alert.

5. Enter a time, distance, or calorie
amount.

6. Go for a ride.

Each time you reach the alert amount,
the Edge beeps and displays a message.

NOTE

messages, see page 41.

Using Advanced Alerts

If you have an optional heart rate
monitor, GSC 10, or third-party ANT+
power sensor, you can set up advanced
alerts.

1. Press and hold MENU.

2. Select Training > Alerts.

3. Select an option:

Training with Your Edge

: To turn on audible tones for

Select HR Alert to set the

•
minimum and maximum heart
rate in beats per minute (bpm).

NOTE: For more information
about heart rate zones and
settings, see page 22.

Edge 500 Owner’s Manual 9

Training with Your Edge

Select Cadence Alert to set the

•
fast and slow cadence amounts
in revolutions of the crank arm
per minute (rpm).

Select Power Alert to set the

•
minimum and maximum power
amounts in watts.

4. Go for a ride.

Each time you exceed or drop below

the specied heart rate, cadence, or

power amount, the Edge beeps and
displays a message.

NOTE: To turn on audible tones for
messages, see page 41.

Using Auto Lap by Distance

You can use Auto Lap® to

automatically mark the lap at a specic

distance. This feature is helpful for
comparing your performance over
different parts of a ride (for example,
every 10 miles or 40 kilometers).

1. Press and hold MENU.

2. Select Settings > Bike Settings >

Auto Lap.

3. In the Auto Lap Trigger eld,
select By Distance.

4. Enter a value.

5. Customize optional lap data elds

(page 37).

6. Go for a ride.

10 Edge 500 Owner’s Manual

Using Auto Lap by Position

You can use Auto Lap to automatically

mark the lap at a specic position.

This feature is helpful for comparing
your performance over different parts
of a ride (for example, a long climb or
training sprints).

1. Press and hold MENU.

2. Select Settings > Bike Settings >

Auto Lap.

3. In the Auto Lap Trigger eld,
select By Position.

4. Select an option:

Select Lap Press Only to

•

trigger the lap counter each time
you press LAP and each time
you pass any of those locations
again.

5. Customize optional lap data elds

6. Go for a ride.

NOTE: During courses, use the By

Position option to trigger laps at all of

the lap positions saved in the course.

Training with Your Edge

Select Start And Lap to

•
trigger the lap counter at the
GPS location where you press

START and at any location

during the ride where you press

LAP.

Select Mark And Lap to trigger

•

the lap counter at a specic GPS

location marked before the ride
and at any location during the
ride where you press LAP.

(see page 37).

Edge 500 Owner’s Manual 11

Training with Your Edge

Using Auto Pause

You can use Auto Pause® to pause the
timer automatically when you stop
moving or when your speed drops

below a specied value. This feature is

helpful if your ride includes stop lights
or other places where you need to slow
down or stop.

NOTE: The paused time is not saved
with your history data.

1. Press and hold MENU.

2. Select Settings > Bike Settings >

Auto Pause.

3. Select an option:

Select Off.

•

Select When Stopped to pause

•
the timer automatically when
you stop moving.

Select Custom Speed to pause

•
the timer automatically when
your speed drops below a

specied value.

12 Edge 500 Owner’s Manual

4. Customize optional time data elds

(see page 37).

To view the entire time (from
pressing START to RESET), select
the Time - Elapsed data eld.

5. Go for a ride.

Using Auto Scroll

Use the auto scroll feature to
automatically cycle through all of the
training data pages while the timer is
running.

1. Press and hold MENU.

2. Select Settings > Bike Settings >

Auto Scroll.

3. Select a display speed: Slow,

Medium, or Fast.

4. Go for a ride.

The training data pages scroll
automatically. You can press PAGE
to manually switch pages.

Courses

Courses allow you to train using a
previously recorded activity. You can
follow the course trying to match
or exceed previously set goals. For
example, if the original course was
completed in 30 minutes, you will
race against a Virtual Partner® trying
to complete the course in under 30
minutes.

Garmin recommends that you use
Garmin Connect or Garmin Training
Center (page 7) to create courses. You
can then transfer the courses to your
Edge (page 35).

Course Points

You must use Garmin Training
Center to add course points to any
course. You can add course points, or
places on your course that you want
to remember, such as water stops or
distance goals.

Training with Your Edge

Creating Courses with Your
Edge

Before you can create a course, you
must have history with GPS track data
saved to the Edge.

1. Press and hold MENU.

2. Select Training > Courses > New.

3. Select a previous ride on which to
base your course.

The Edge assigns a default name
to your new course that appears in
the list.

4. Select the course from the list.

5. Select Edit Course to rename the
course.

6. Enter a descriptive course name

in the top eld (for example,

18mi_Ridgeview).

Edge 500 Owner’s Manual 13

Training with Your Edge

Starting a Course

1. Press and hold MENU.

2. Select Training > Courses.

3. Select the course from the list.

4. Select an option:

Select Do Course.

•

Select Map to preview the

•
course, and press BACK to
return to the course list.

Select Prole to preview the

•

elevation prole, and press

BACK to return to the course

list.

5. Press START.

History is recorded even if you are
not on the course. The “Course
Complete” message appears when

you nish.

6. Go for a ride.

7. Press PAGE to view the data pages:

14 Edge 500 Owner’s Manual

Off Course Options

You can include a warmup before you
begin your course. Press START to
begin the course, and then warm up as
normal. Stay away from your course
path as you warm up. When you are
ready to begin, head toward your
course. When you are on any part of
the course path, the Edge displays an
“On Course” message.

NOTE: As soon as you press START,
your Virtual Partner starts the course
and does not wait for you to warm up.

If you stray away from the course,
the Edge displays an “Off Course”
message. Use the course map or course

points to nd your way back to the

course.

Training with Your Edge

You

Virtual
Partner

Edge 500 Owner’s Manual 15

Training with Your Edge

Changing the Course Speed

1. Press and hold MENU.

2. Select Training > Courses.

3. Select the course from the list.

4. Select Do Course.

5. Press LIGHT.

6. Use▼ and ▲ to adjust the
percentage of time to complete the
course.

For example, to improve your
course time by 20%, enter a course
speed of 120%. You will race

against the Virtual Partner to nish

a 30-minute course in 24 minutes.

Stopping a Course

Press and hold MENU, and select

Training > Stop Course.

Deleting a Course

1. Press and hold MENU.

2. Select Training > Courses.

3. Select a course.

4. Select Delete Course > Yes.

Workouts

You can use the Edge to create
workouts that include goals for each
workout step and for varied distances,
times, and rest laps. After you create a
workout, you can use Garmin Connect
or Garmin Training Center to schedule
the workout for a particular day. You
can plan workouts in advance and store
them on your Edge.

16 Edge 500 Owner’s Manual