GAI-Tronics HUBBCOM GSC1000, HUBBCOM GSC2000 Quick Installation Manual
Pub. 42004-527AQG
ATTENTION
WARNING
WARNING
GAI-TRONICS® CORPORATION
A H U B B E L L C O M P A N Y
HUBBCOM™ GSC1000/GSC2000 Desktop/Wall-Mount
Smart Controller Quick Installation Guide
Important Safety Instructions
Read, follow, and retain instructions—All safety and operating instructions should be read and followed before operating
the unit. Retain instructions for future reference.
Heed warnings—Adhere to all warnings on the unit and in the operating instructions.
Attachments—Attachments not recommended by the product manufacturer should not be used, as they may cause
hazards.
Servicing—Do not attempt to service this unit by yourself. Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
—Install equipment without modification and according to all applicable local, national and
international electrical codes. North America - Consult the National Electrical Code (NFPA
70), Canadian Standards Association (CSA 22.1), and local codes for specific requirements
regarding your installation. Class 2 circuit wiring must be performed in accordance with NEC
725.55.
These enclosures must be installed by trained, qualified and competent personnel. Installation must comply with state and
national regulations, as well as safety practices for this type of equipment.
—In 24 V dc systems: Under NO condition should this equipment be operated from a battery
charger without the batteries connected.
In 24 V dc systems, most chargers have an unloaded output of 35 to 45 volts that can quickly damage the equipment designed
for nominal 24 volts. The maximum battery voltage should never exceed the maximum specified input voltage.
—Do not disconnect equipment while energized.
Ensure proper grounding to protective earthing.
General Information
This guide covers the installation of the HUBBCOM™ Desktop/Wall-Mount Smart Controller, Models GSC1000 and
GSC2000. The Model GSC1000 Smart Controller is equipped with a handset and is only configured for horizontal
(landscape) installations. The Model GSC2000 Smart Controller is not equipped with a handset and can be configured for
vertical (portrait) or horizontal (landscape) use (see Figure 1). See the GAI-Tronics website at https://www.gai-tronics.com
for, system specifications, warranty information, and the HUBBCOM™ Smart Controller Configuration App.
Service and Spare Parts
If the equipment requires service or spare parts, contact your Regional Service Center for assistance. If service is required, a
return authorization number (RA#) will be issued. Equipment should be shipped prepaid to GAI-Tronics with a return
authorization number and a purchase order number. If the equipment is under warranty, repairs or a replacement will be made
in accordance with GAI-Tronics’ warranty policy. Please include a written explanation of all defects to assist our technicians
in their troubleshooting efforts. Call 800-492-1212 inside the USA or 610-777-1374 outside the USA for help with
identifying the Regional Service Center closest to you.
Installation
The HUBBCOM™ Model GSC1000 and Model GSC2000 can be wall mounted or used as desktop units.
GAI-Tronics Corporation 3030 Kutztown Road Reading, PA 19605 USA
610-777-1374 800-492-1212 Fax: 610-796-5954
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
Pub. 42004-527AQG
HUBBCOM™ GSC1000/GSC2000 Desktop/Wall-Mount Smart Controller Quick Installation Guide Page 2 of 4
Figure 1. HUBBCOM
™
Model GSC1000 (horizontal) and Model GSC2000 (vertical) Smart Controllers
Desktop Units
The HUBBCOM™ Smart Controller can be used as a desktop station by installing the included kickstand (see Figure 2).
Handset units must be setup horizontally. Hands-free units can be configured vertically or horizontally (based on
programming).
1.
Remove the cable termination cover and set it aside.
2.
Complete the necessary cable terminations as described in the Wiring section.
3. Route the terminated wires through the half round access holes and secure with a ty-wrap using the integrated anchors.
4.
Replace the cable termination cover by hooking the two tabs into the slots and rotating the cover downward until it clicks
into place.
5.
Install the kickstand. The kickstand provides four positions in both orientations to suit the situation where it will be used
(see Table 1 and Figure 4).
1. Determine the orientation of the unit.
2.
Insert one side of the kickstand with the flange properly oriented into the desired position in the rear cutout (see
Figure 4).
3. Press the other side into place and compress firmly to snap it into place.
Table 1. Smart Controller Kickstand Positions
Orientation/
Position
Horizontal
Models
GSC1000 &
GSC2000
Vertical
Model
GSC2000
Figure 2. Smart Controller Kickstand
P:\Standard IOMs - Current Release\42004-xxxxQG Quick Guides\42004-527AQG.docx
05/18
1
(flange up)
2
(flange up)
2
(flange down)
3
(flange up)
75° 75°
60° 60°
45° 45°
30° 30°
Loading...