www.furuno.co.jp
9‑52Ashihara‑cho,
Fax:
A:MAR
2008
.
B:JUN.18,2008
Pub.No.
OME‑44420‑B
*
00016841411
**00016841411
*
(
TATA
)
FA‑50
*
00016841411
**00016841411
*
Nishinomiya,662‑8580,JAPAN
Telephone: +81‑(0)798‑65‑2111
+81‑(0)798‑65‑4200
Thepaperusedinthismanual
iselementalchlorinefree.
・FURUNOAuthorizedDistributor/Dealer
Allrightsreserved.
PrintedinJapan
*00016841411*
IMPORTANT NOTICES
z The descriptions in this manual are intended for readers with a solid knowledge of English.
z No part of this manual may be copied or reproduced without written permission.
z If this manual is lost or worn, contact your dealer about replacement.
z The contents of this manual and equipment specifications are subject to change without notice.
z The example screens (or illustrations) shown in this manual may not match the screens you
see on your display. The screen you see depends on your system configura tion and equipment
settings.
z Store this manual in a convenient place for future reference.
z FURUNO will assume no responsibility for the damage caused by improper use or modification
of the equipment (including software) by an unauthorized agent or a third party.
z When it is time to discard this product it must be done according to local regulations for disposal
of industrial waste. For disposal in the USA, refer to the Electronics Industries Alliance (http://
www.eiae.org/).
i
SAFETY INSTRUCTIONS
The operator and installer must read the applicable safety instructions before attempting to install
or operate the equipment.
Indicates a potentially hazardous situation which, if not avoided,
WARNING
CAUTION
Warning, Caution
Safety instructions for the operator
could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
can result in minor or moderate injury.
Prohibitive Action
Mandatory Action
WARNING
Do not open the shield cover.
Only qualified personnel should work
inside the equipment.
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury can
result.
Immediately turn off the power at the
power source if
water leaks into the equipment
something is dropped into the
equipment
the equipment is emitting smoke or
is on fire
the equipment is emitting strange
noises
Continued use of the equipment can
cause fire or electrical shock. Contact a
FURUNO dealer or agent for service.
WARNING
WARNING
Do not place liquid-filled containers on
the top of the equipment.
Fire or electrical shock can result if a
liquid spills into the equipment.
Make sure no rain or water splash
leaks into the equipment.
Fire or electrical shock can result if water
leaks into the equipment.
Warning labels are attached to the equipment.
Do not remove these labels. If a label is missing
or illegible, contact a FURUNO agent or dealer
replacement.
WARNING
To avoid electrical shock, do
not remove cover. No userserviceable parts inside.
Name: Warning Label (1)
Type: 86-003-1011-1
Code No.: 100-236-232-10
Do not operate the equipment with wet
hands.
Electrical shock can result.
Use the proper fuse.
Use of the wrong fuse can cause fire
or electrical shock.
WARNING
To avoid electrical shock,
do not remove cover.
No user-serviceable parts
inside.
Name: Warning Label (2)
Type: 86-129-1001-1
Code No.: 100-236-742-10
ii
CAUTION
Safety instructions for the installer
WARNING
SAFETY INSTRUCTIONS
ELECTRICAL SHOCK HAZARD
Do not open the equipment unless
totally familiar with electrical circuits
and service manual.
Only qualified personnel should work
inside the equipment.
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water splash.
Water in the equipment can result in fire,
electrical shock or damage to the equipment.
Be sure that the power supply is
compatible with the voltage rating of the
equipment.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
FA-50
PR-240
GVA-100-T
DB-1
Standard
compass
0.30 m 0.30 m
0.90 m 0.60 m
0.30 m 0.30 m
0.30 m 0.30 m
Steering
compass
Connecting an incompatible power supply
can cause fire or damage the equipment.
The voltage rating appears on the inlet
of power.
iii
TABLE OF CONTENTS
FOREWORD ....................................................................................................................v
SYSTEM CONFIGURATIONS.......................................................................................vii
1. INSTALLATION .....................................................................................................1-1
1.1 Equipment List ........................................................................................................... 1-1
1.2 AIS Transponder FA-50 .............................................................................................1-3
1.3 VHF Antenna.............................................................................................................. 1-3
1.4 GPS Antenna ............................................................................................................. 1-5
1.5 GPS/VHF Combined Antenna.................................................................................... 1-7
1.6 AC-DC Power Supply (option) ...................................................................................1-9
1.7 Wiring .......................................................................................................................1-10
1.8 Setting and Adjustments ..........................................................................................1-12
1.8.1 COM PORT setup, Network setup ............................................................... 1-12
1.8.2 Ship static..................................................................................................... 1-15
2. OPERATION ..........................................................................................................2-1
2.1 AIS Transponder FA-50 .............................................................................................2-1
2.2 Messages ................................................................................................................... 2-2
2.2.1 Sending a message .......................................................................................2-2
2.2.2 Confirming receiving messages..................................................................... 2-3
2.3 Own Vessel Data Display........................................................................................... 2-4
2.4 Alarm Status............................................................................................................... 2-7
2.5 Sensor Status............................................................................................................. 2-8
3. MAINTENANCE,
TROUBLESHOOTING3-1
3.1 Maintenance............................................................................................................... 3-1
3.2 Replacing the Fuse .................................................................................................... 3-2
3.3 Troubleshooting .........................................................................................................3-2
3.4 Diagnostics.................................................................................................................3-3
APPENDIX 1 MENU TREE .......................................................................................AP-1
APPENDIX 2 VHF CHANNEL LISTS........................................................................AP-2
APPENDIX 3 PARTS LIST, LOCATIONS ................................................................AP-4
APPENDIX 4 DIGITAL INTERFACE.........................................................................AP-6
PACKING LISTS..........................................................................................................A-1
SPECIFICATIONS .....................................................................................................SP-1
OUTLINE DRAWINGS.................................................................................................D-1
INTERCONNECTION DIAGRAM ................................................................................ S-1
INDEX..........................................................................................................................IN-1
iv
FOREWORD
A Word to the Owner of the FA-50
Congratulations on your choice of the FURUNO FA-50 AIS Transponder. We are confident you
will see why the FURUNO name has become synonymous with quality and reliability.
For 60 years FURUNO Electric Company has enjoyed an enviable reputation for quality marine
electronics equipment. This dedication to excellence is furthered by our extensive global network
of agents and dealers.
This equipment is designed and constructed to meet the rigorous demands of the marine environment. However, no machine can perform its intended function unless operated and maintained
properly. Please carefully read and follow the recommended procedures for operation and maintenance.
Thank you for considering and purchasing FURUNO equipment.
Features
The FA-50 is a Class B AIS (Automatic Identification System) capable of exchanging navigation
and ship data between own ship and other ships or coastal stations. It complies with IMO MSC.
140(76) Annex 3, A.694, ITU-R M.1371-2 and DSC ITU-R M.825-3 It also complies with IEC
60945 (EMC and environmental conditions).
FA-50 consists of VHF and GPS antennas, a transponder unit and several associated units. The
transponder contains a VHF transmitter, two TDMA receivers on two parallel VHF channels, interface, communication processor, and internal GPS receiver. The internal GPS is a 12-channel allin-view receiver with a differential capability. It also gives position, COG and SOG when the external GPS. FA-50 receives DSC, time-sharing with TDMA receiver.
The main features are:
z Safety of navigation by automatically exchanging navigational data
z Static data
• MMSI (Maritime Mobile Service Identity)
• Call sign & Ship’s name
• Type of ship
• Location of position-fixing antenna on the ship
z Dynamic data
• Ship's position with accuracy indication and integrity status
• Universal Time Coordinated (UTC)
• Course over ground (COG)
• Speed over ground (SOG)
• Heading
z Voyage-related data
• Hazardous cargo (type)
z Short safety-related messages, pre-set messages
v
FOREWORD
z Interfaces for radar, PC for future networking expansion
z GPS/VHF combined antenna for easy installation available
z Built-in GPS receiver for position-fixing device
Program Version
Item Program No. Version No. Date
FA-50 AIS Transponder
Main Program
**: Minor change
0550233 01.** July 2007
vi
SYSTEM CONFIGURATIONS
Either
GPS antenna
GPA-017S or 017
AIS TRANSPONDER
FA-50
VHF
antenna
GPS/VHF
combined antenna
GVA-100-T
Distributor
DB-1
HUB
PC
w/FAISPC MX
EXTERNAL
DISPLAY
NAVNET
AC-DC POWER
SUPPLY PR-240
100-115/
200-230VAC
1φ, 50/60 Hz
24 VDC
: Standard supply
: Optional supply
: Local supply
NAVNET
EXTERNAL
DISPLAY
OR
SENSOR
OR
12-24 VDC
*Usaually FA-50 uses the internal GPS. When connecting the
external GPS, use one which satisfies the following points.
1) Outputs DTM sentence (WGS-84 can be chosen.)
2) Outputs GBS sentence.
3) Outputs sentences with the mode indicator;
GNS: Ver.3.0 and later
GLL: Ver.2.0 and later
GGA: Ver.2.0 and later
RMC: Ver.1.5 and later
GPS navigator GP-150 meets with requirements shown above.
IF-1500AIS
RADAR
CHART PLOTTER
ECDIS
PILOT PLUG
GPS* (ex. GP-150)
SPEED LOG
GYROCOMPASS
SATELLITE COMPASS
FR-8xx2 SERIES
vii
SYSTEM CONFIGURATIONS
This page is intentionally left blank.
viii
1. INSTALLATION
1.1 Equipment List
Standard supply
Name Type Code No. Qty Remarks
AIS transponder FA-50 - 1
Antenna unit GVA-100 - 1 GPS/VHF combined
GPA-017S - 1 set GPS antenna
GPA-017 - 1 set GPS antenna w/10 m
Distributor DB-1 - 1 For GVA-100
Spare parts SP05-05801 001-031-960 1 set 4A fuses (Type: FGMB
cable
125V 4A, Code No.:
000-157-482-10)
Accessories FP05-06110 000-166-648 1 set FAISPC-MX for PC
Installation
materials
CP24-00502 005-955-560 1 set For GPA-017S
CP05-11401 001-031-970 1 set For FA-50, self-tapping
screws (Type: 4x20,
Code No.: 000-158-
850-10)
TNC-PS/PS3D-L15M-R
CP24-00101 005-950-730 1 set For DB-1, self-tapping
000-133-670-11 1 For GPA-017S, 15 m
cable
screws (Type: 4x30,
Code No.: 000-162-
659-10)
1-1
1. INSTALLATION
Optional supply
Name Type Code No. Qty Remarks
AC-DC power
supply
Whip antenna CP05-11001 001-034-670 1 For outside Japan
Antenna cable
set
Coaxial cable TNC-PS/PS-3D-
Right-angle
antenna base
L-angle antenna base
Antenna base
for rail mount
Mast mount
fixture
PR-240-CE - 1
CP20-02700 004-381-160 1 For GPA-017S
CP20-02710 004-381-170 1 For GPA-017S
CP24-00300 000-041-938 1 For GVA-100
CP24-00310 000-041-939 1 For GVA-100
000-133-670-11 1 TNC-TNC, 15 m
L15M-R
No.13-QA330 000-803-239 1 For GPA-017/S
No.13-QA310 000-803-240 1 For GPA-017/S
No.13-RC5160 000-806-114 1 For GPA-017/S
CP20-01111 004-365-780 1 For GPA-017/S
AIS viewer FAISPC-MX50 000-160-966 1
LAN cable P5E-4PTX-BL
L=2M
P5E-4PTX-BL
L=10M
Cable assy MJ-A6SPF0017-
010C
MJ-A6SPF0017050C
MJ-A6SPF0017100C
MJ-A6SPF0017200C
MJ-A6SPF0017300C
000-164-634-10 1 2 m
000-164-637-10 1 10 m
000-159-704-11 1 For NavNet VX2, 1 m
000-159-705-11 1 For NavNet VX2, 5 m
000-159-706-11 1 For NavNet VX2, 10 m
000-159-707-11 1 For NavNet VX2, 20 m
000-159-708-11 1 For NavNet VX2, 30 m
Note: One FA-50 can be installed on a network.
1-2
1.2 AIS Transponder FA-50
Mounting considerations, mounting
The FA-50 can be mounted on a desktop, deck or on a bulkhead. When selecting a
mounting location, keep the following points in mind:
• The temperature and humidity should be moderate and stable.
• Locate the unit away from exhaust pipes and vents.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• Keep the unit away from electromagnetic field-generating equipment such as motors and generators.
• A magnetic compass will be affected if the FA- 50 is placed too close to it. Observe
the compass safe distances noted in the safety instructions to prevent disturbance
to the magnetic compass.
Fix the unit to the mounting location with 4x20 self-tapping screws (supplied).
1. INSTALLATION
1.3 VHF Antenna
Location
The location of the AIS VHF-antenna should be carefully considered. Digital communication is more sensitive than analog/voice communication to interference created by
reflections in obstructions like masts and booms. It may be necessary to relocate the
VHF radiotelephone antenna to minimize interference effects. To minimize interference effects, the following guidelines apply:
• The AIS VHF antenna should be placed in an elevated position that is as free as
possible with a minimum of 0.5 meters in the horizontal direction from constructions
made of conductive materials. The antenna should not be installed close to any
large vertical obstruction. The objective for the AIS VHF antenna is to see the horizon freely through 360 degrees.
• There should not be more than one antenna on the same plane. The AIS VHF antenna should be mounted directly above or below the ship's primary VHF radiotelephone antenna, with no horizontal separation and with a minimum of 2.8 meters
vertical separation. If it is located on the same plane as other antennas, the distance
apart should be at least 10 meters.
• Install the VHF whip antenna (option) referring to the outline drawing at the back of
this manual. Separate this antenna from other VHF radiotelephone antennas as
shown below to prevent interference to the FA-50.
1-3
1. INSTALLATION
Whip antenna
for AIS
Horizontal separation distance
Cabling
• Use coaxial cable type 5D-2V or the equivalent.
Other VHF
whip antenna
More than 10 m
More than
2.8 m
More than 0.5 m
Vertical separation distance
• The cable should be kept as short as possible to minimize signal attenuation, and
the maximum length is 50 meters.
• All outdoor-installed connectors on coaxial cables should be fitted with preventive
isolation such as vulcanizing tape to protect against water penetration into the antenna cable.
• Coaxial cables should be installed in separate signal cable channels/tubes and at
least 10 cm away from power supply cables. Crossing of cables should be done at
right angles (90 degrees). The minimum bend radius of the coaxial cable should be
5 times the cable's outer diameter.
1-4
1.4 GPS Antenna
Install the GPS antenna unit referring to the outline drawing at the back of this manual.
When selecting a mounting location for the antenna, keep in mind the following points.
• Select a location out of the radar beam. Th e radar beam will obstruct or prevent reception of the GPS satellite signal.
• There should be no interfering object within the line-of-sight to the satellites. Objects
within line-of-sight to a satellite, for example, a mast, may block reception or prolong
acquisition time.
• Mount the antenna unit as high as possible to keep it free of interfering objects and
water spray, which can interrupt reception of GPS satellite signal if the water freezes.
Extending antenna cable
Three types of antenna cable extensions are optionally available.
• Antenna cable set CP20-02700
1. INSTALLATION
Antenna Unit
0.6m
Antenna Cable
30m 1 m
TNCP-NJ
Conversion
Cable Assy.
NJ-TP-3DXV-1
Fabricate locally. (See next page.)
N-P-8DFB
: Connector
FA-50
Waterproofing connector
Wrap connector with vulcanizing tape and then vinyl tape. Bind the tape end with a
cable-tie.
• Antenna cable set CP20-02710 (8D-FB-CV, 50 m)
• Connect the cable the same as 1) above.
Note: The length of this cable should be less tha n 20 m to prevent signal loss. The
coax. coupling cable assy.(type: NJ-TP-3DXV-1, code no. 000-123-809), coaxial
connector (N-P-8DFB; supplied), vulcanizing tape and vinyl tape are required. Fabricate both ends of the cable as shown in the figure on the next page.
1-5
1. INSTALLATION
e
r
How to attach the connector N-P-8DFB for cable 8D-FB-CV
Outer Sheath
Inner Sheath
Shield
Armor
50
30
Cover with heat-shrink tubing and heat.
30
Washer 1
10
Clamp
Clamp
Nut
Gasket
(reddish
brown)
Aluminum Foil
Remove outer sheath and armor by the dimensions
shown left.
Expose inner sheath and shield by the dimensions
shown left.
Cut off insulator and core by 10mm from its end.
Twist shield end.
Slip on clamp nut, washer 1, gasket and clamp as
shown left. If it is difficult to slip the clamp onto the
cable, use a file to enlarge the inner diameter of the
clamp.
Clamp Nut
Trim shield here.
Insulator
Trim aluminum
tape foil here.
Washer 2
5
Spacer (white)
Pin
Shell
Fold back shield over clamp and trim.
Cut aluminum foil at four places, 90° from one
another.
Fold back aluminum foil onto shield and trim.
Slit the washer 2, and trim insulator at the end of th
washer 2.
Expose the core by 5mm.
Slip the pin onto the conductor. Solder them togethe
through the hole on the pin.
1-6
Solder through
the hole.
Insert the pin into the spacer (white) and shell.
Screw the clamp nut into the shell.
(Tighten by turning the clamp nut. Do not tighten by
turning the shell.)
1.5 GPS/VHF Combined Antenna
Install the combined antenna unit referring to the outline drawing. When selecting a
mounting location for the antenna, keep in mind the following points.
• Select a location out of the radar beam. Th e radar beam will obstruct or prevent reception of the GPS satellite signal.
• There should be no interfering object within the line-of-sight to the satellites. Objects
within line-of-sight to a satellite, for example, a mast, may block reception or prolong
acquisition time.
• Mount the antenna unit as high as po ssible. Mo unting it this way keeps it free o f interfering objects and water spray, which can interrupt reception of GPS satellite signal if the water freezes.
1. INSTALLATION
Outdoor
N-P-8DFB
RG-10U/Y or 8D-FB-CV
Indoor
Distributor DB-1
GPS
VHF
N-P-8DFB
AIS Transponder
FA-50
Installation overview of GPS/VHF combined antenna
Mounting procedure
1. Dismount the bottom cover, cut the cable-tie inside the unit and take out the co-
axial connector attached to the combined box.
2. Loosen four screws to loosen whip antenna fixture and pull out the coaxial con-
nector coming from the combined box through the hole in the whip antenna fixture.
3. Connect the coaxial connector to the whip antenna base and wrap the junction
part of the whip antenna with vulcanizing tape and then vinyl tape for waterproofing.
4. Insert the whip antenna from the top of the combined antenna.
5. Secure the whip antenna with whip antenna fixture.
6. Using a new plastic band (supplied), secure the cables and coaxial connector in-
side the antenna case.
7. Mount the bottom cover.
8. Fix the GPS/VHF combined antenna to the ship's stanchion (40 to 50 mm diame-
ter) with antenna fixing brackets, flat washers and hex. nuts. For 60 to 80 mm diameter stanchion, the mast fixing kit (Type: OP24-5, Code No.: 005-954-510) is
necessary.
Note: Coat the exposed parts of bolts and nuts with silicon sealant.
1-7
1. INSTALLATION
Antenna fixing bracket
Whip antenna fixture
Loosen four screws.
(M5x16)
Combined box
Bottom cover
GPS/VHF combined antenna
Installing distributor DB-1
The top of the stanchion comes
into contact with the flange.
Stanchion
1-8
The length of the cable between the distributor and transponder is 1 m so locate the
distributor within 1 m from the transponder. Fix the distributor on the bulkhead, facing
the cable entrance downward. Remove the lid of the distributor and secure the distributor with two self-tapping screws.
Self-tapping screw
(4x30)
Note: Be sure no foreign material or water enters the distributor.
1. INSTALLATION
1.6 AC-DC Power Supply (option)
When selecting a mounting location for the unit, keep the following in mind:
z Keep the unit out away from areas subject to water splash.
z Locate the unit away from exhaust pipes and vents.
z The mounting location should be well ventilated.
z Mount the unit where shock and vibration are minimal.
z A magnetic compass will be affected if the unit is pla ced too close to it. Observe the
following compass safe distances to prevent disturbance to the magnetic compa ss:
• Steering compass: 0.6 m
• Standard compass: 0.9 m
Fix the unit with four self-tapping screws (4x16) to a desktop or the deck. It is not necessary to open the cover.
1-9
1. INSTALLATION
1.7 Wiring
Connect power source, LAN cable, VHF antenna and ground wire as shown below.
GPS Antenna
GPA-017/S
150M-W2VN
0.6 m
RG-10U/Y, 50 m
8D-FB-CV, 30 m/50 m: Option
RG-10U/Y, 20 m: Local supply
COM/POWER
12-24 VDC
2.0-1.0 A
Either one
AIS TRANSPONDER
NETWORK
GPS ANT
GPS/VHF Combined
Antenna GVA-100-T
Distributor
DB-1
Attached to Distributor
(approx. 1m)
: Ground is not required.
VHF ANT
0.8 m
RG-10U/Y (8D-FB-CV,
option)
RS-422 RATING*2
RED BLACK
Switchboard breaker
*1: Supply from breaker on switchboard.
*2: If COM lines (connection for NavNet, sensor) are not used,
tape them to prevent short circuit.
PC, HUB,
NAVNET
POWER CABLE
(supplied)
12-24 VDC*1
-
+
LAN CABLE
P5E-4PTX-BL
(2 m or 10 m)
GROUND WIRE
IV-1.25sq
GROUND
: Standard
: Option
: Local Supply
1-10
Loading...