Fulgor Milano F4GK42S1 INSTALLATION INSTRUCTIONS

F4GK24*1 F4GK30*1 F4GK36*1 F4GK42*1

GAS COOKTOP

PLAQUE DE CUISSON GAZ

PLACA DE COCCIÓN DE GAS

EN INSTALLATION INSTRUCTIONS

FR INSTRUCTIONS D’INSTALLATION

ES INSTRUCCIONES DE INSTALLACIÓN

Dear Customer,

Thank you for purchasing a Fulgor Milano product. Fulgor Milano is committed to excellence and our signature technologies provide you with professional tools for your kitchen. One of our central philosophies is continuous investment in research that is rooted in developing life enhancing technology. Our goal is to deliver products that are worthy of your family recipes and that will breathe life into your kitchen, the heart of your home. We invite you to enjoy your new Fulgor Milano product with same amount of care and attention that we have put into creating it.

Your Life | Our Passion

TABLE OF CONTENTS PAG E

1 - Special Warnings 2

Before Starting Installation 2 Cooktop Installed over Oven Installation 2

2 - Product Dimensions and Cutout Requirements 3

Important Preparation Suggestions 3 Mobile Home Installation 6

3 - Cooktop Installation 7 4 - Gas Requirement 9

Gas Connection 10 Pressure Testing 12 Pressure Test Method 12

5 - Electrical Requirements 13

General Information 13 Electrical Connection 13 Electrical Requirements 13

6 - Conversion for LP or NG Gas 15

Converting Appliance for Use with LP Gas 15 Replace injector on (one ring ﬂame burners) 15 Replace injectors on (two rings ﬂame burner) 15 Converting Appliances for Use with NG Gas 16 Pressure regulator conversion 16 Injectors position 17 Low Flame Adjustment 18 Electric gas ignition 19

The Burner Flames 19

Pay attention to these symbols present in this manual:

DANGER

You can be killed or seriously injured if you don’t IMMEDIATELY follow instructions.

WARNING

• This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

• You can be killed or seriously injured if you don’t follow these instructions.

READ AND SAVE THESE INSTRUCTIONS.

To installer:

Leave these instructions with the appliance.

To customer:

Retain these instructions for future reference.

WARNING

• If the information in this manual is not followed exactly, a ﬁre or explosion may result in personal injury or death.

• Do not store or use gasoline or other ﬂammable vapours and liquids in the vicinity of this or any other appliance.

IMPORTANT: Save these instructions for the local electrical

inspector use.

INSTALLER: Please leave this manual with owner for future

reference.

OWNER: Please keep this manual for future reference.

1 - Special Warnings

IMPORTANT

Please read all instructions before using this appliance.

Proper installation is your responsibility. Have a qualiﬁed technician install this cooktop.

IMPORTANT

• Observe all governing codes and ordinances.

• Write down the model and serial numbers before installing the cook top. Both numbers are on the serial rating plate located on bottom of cooktop box.

Before Starting Installation

• Check location where cooktop will be installed. The location should be away from strong drafty areas, such as windows, doors and strong heating vents or fans.

• Electrical grounding is required. See “Electrical Requirements”

• Assure that electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 - latest edition**, or Canadian Electrical Code, part 1 C22.1 (latest edition)*** and all local codes and ordinances.

WARNING

BEFORE CONNECTING THE APPLIANCE ON THE GAS LINE SUPPLY, ENSURE THAT ITS GAS SETTING IS APPROPRIATE. THE TYPE OF GAS ADJUSTED AND SHIPPED FROM THE FACTORY IS INDICATED ON THE RATING PLATE LOCATED ON BOTTOM OF THE BURNER BOX.

Cooktop Installed over Oven Installation

Only certain speciﬁed cooktop and oven models are approved for cooktop over oven installations. Cooktops approved for this type of installation will have an approval label located on the outside of the burner box. If you do not ﬁnd this label, contact your dealer to conﬁrm that cooktop is approved. The label on the bottom of your cooktop lists the cooktop and oven combinations that are approved for this type of installation.

• Assure that gas connection conforms with local codes and ordinances. In the absence of local codes, installations must conform with American National Standard, National Fuel Gas Code ANSI Z223/NFPA 54 - latest edition** The Natural Gas and Propane Installation Code, CSA

149.1 or CSA B149.2 latest edition***.

Copies of the standards listed may be obtained from: ** National Fire Protection Association One Batterymarch

Park Quincy, Massachusetts 02269 *** CSA International 8501 East Pleasant Valley Rd.

Cleveland, OH 44131-5575

NOTE: This cooktop is manufactured for use with Natural

gas or Propane.

To convert to LP (propane) or NG (natural gas),

see instruction in the gas conversion kit provided in literature package. Proper gas supply connection must be available. See gas supply requirements.

2 - Product Dimensions and Cutout Requirements

Important Preparation Suggestions

1. Chamfer all exposed edges of decorative laminate to prevent damage from chipping.

2. Radius corners of cutout and ﬁle to Insure smooth edges and prevent corner cracking. Recommend 1/4”or 3/8” diameter drill In each corner.

3. Rough edges, inside corners which have not been rounded and forced ﬁts can contribute to cracking of the countertop laminate.

PRODUCT DIMENSIONS

24”

20-1/16” (51 cm)

2-15/16” (7,4 cm)

20-1/16” (51 cm)

2-15/16” (7,4 cm)

20-1/16” (51 cm)

24-1/2” (62 cm)

30”

30” (76 cm)

36”

2-15/16” (7,4 cm)

16-3/4” (42,5 cm)

2-15/16” (7,4 cm)

36” (91 cm)

42”

44” (112 cm)

5-11/16 “ (14,4 cm)

7-5/8 “ (19,3 cm)

COUTOUT DIMENSIONS

CUT OUT

WIDTH

24”

30”

36”

A B C D

MIN. 23-1/2” ( 59,7 cm) MAX. 23-5/8” ( 60,0 cm)

MIN. 29” ( 73,7 cm) MAX. 29-1/8” ( 74,0 cm)

MIN. 34-7/8” ( 88,6 cm) MAX. 35” ( 88,9 cm)

MIN. 43-1/8” (109,6 cm) MAX. 43-1/4” (109,9 cm)

MIN. 19-5/16” (49,0 cm) MAX. 19-3/8” (49,3 cm)

MIN. 15-15/16” (40,5 cm) MAX. 16-1/16” (40,8 cm)

2-1/2” ( 6,35 cm) MIN. 3” (7,62 cm)

4” (10,16 cm) MIN. 3” (7,62 cm)

CUTOUT REQUIREMENTS

C D

G H

* NOTE:

- If cabinet has a drawer, a 5-1/4”(13,35 cm) depth clearance from the top of the countertop to the top of the drawer (or other obstruction) in base cabinet is required. The drawer depth may need to be shortened to avoid interfering with the regulator.

- 24” (61 cm) min. clearance if bottom of wood or metal cabinets is protected by not less than 1/4” (0.6 cm) ame retardant millboard covered with not less than No. 28 MSG sheet steel 0.015” (0.04 cm) stainless steel, or 0.024” (0.06 cm) aluminium or 0.020” (0.05 cm) copper. 30” (76.2 cm) min. clearance between top of cooking platform and bottom of unprotected wood or metal cabinet.

13” (33 cm) Depth of unprotected overhead cabinets. 30” (76.2 cm) MIN. (Model 30“).

36” (91.4 cm) MIN. (Model 36”). 18” (47.7 cm) MIN. Height from countertop to nearest cabinet on either side of unit. 36” (91 cm ) MIN. (see Note* Clearance from countertop to unprotected overhead surface. )

5” (12.7 cm) min Clearance from cut out to side wall on the left and right of the unit.

From the back corner of cut-out to hole center 2-9/32” (5.8 cm). From the right corner of cut-out to hole center 2-19/32” (6.6 cm). From the back corner of cut-out to hole center 2-9/32 ” (5.8 cm). Opening with oven under cooktop.

From the top of countertop to hole center 4-25/32 ” (12.2 cm). Opening with oven under cooktop.

Electric outlet from bottom of counter top and adjacent to the cabinet side 12” (30.5 cm).

Hole 1-1/5” (3 cm).

We recommend to that you consider the minimum dimension of cut-out size in the case of new installation.

WARNING

The appliance should not be installed with a ventilation system that blows air downward toward the range. This type of ventilation system may cause ignition and combustion problems with the gas cooking appliance resulting in personal injury or unintended operation.

Mobile Home Installation

The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety; Title 24 HUD part 280); or when such standard is not applicable, the Standard for Manufactured Home Installations (Manufactured Home Sites, Communities and Setups), ANSI A225.1 - latest edition, or with local codes.

In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-Z240 - latest edition, or with local codes.

SOLID SURFACE COUNTERTOP INSTALLATION

IMPORTANT

• For solid surface material installations such as Surel™ and Corian®, consult with solid surface manufacturer. Apply heat reﬂective tape such as Scotch® Aluminum Foil Tape #425 or #427 around the cutout so that it folds over on the top and sides.

• DO NOT WRAP THE TAPE UNDERNEATH THE COOKTOP.

• Be sure the tape extends beyond the outermost ﬂange of the cooktop. All corners should be covered with tape.

3 - Cooktop Installation

WARNING

• Excessive Weight Hazard

Use two or more people to move and install cooktop. Failure to do so can result in back or other injury.

• Cut Hazard

Beware of sharp edges. Use the polystyrene ends when carrying the product. Failure to use caution could result in minor injury or cuts.

• Always consult the countertop manufacturer for speciﬁc instructions.

• Ensure the countertop is square and level and ensure no structural members interfere with space requirements.

• Prepare the cut-out according to the instructions (see cutout dimensions).

• Make sure the wall coverings, countertop and cabinets around the cooktop can withstand heat (up to 200 °F).

TOOLS YOU WILL NEED

PARTS

MANUAL GASKET GAS CONVERSION KIT

GAS CONNECTION KIT

SIMMER PLATE (if present)

WOK RING (if present)

POT ADAPTER (if present)

PRESSURE REGULATOR

COOKTOP

GRID

Step 1

Remove packaging materials and literature package from the cooktop before beginning installation. Remove Installation Instructions from literature pack and read them carefully before you begin.

CARDBOARD

Step 2

Before installing apply the foam tape. A tape is provided to seal the cooktop edges to the countertop. Apply tape near inner underside cooktop edge. Use tape around the entire cooktop perimeter. Cut off excess where tape butt ends.

Step 3

Insert the cooktop centered into the cutout opening. Make sure the front edge of the counter top is parallel to the cooktop. Make ﬁnal check that all required clearances are met.

Step 4

Four clamp brackets are provided with your unit. After cooktop has been installed into the countertop, install the brackets on the burner box as shown in ﬁgure. Install the clamp brackets on the front and back of the burner box bottom (if the cabinet construction does not provide clearance for installing brackets at the burner box front back install the clamp brackets on the lateral position of burner box).

step A place the clamping screws into brackets step B attach brackets by using the attachment screws on the

selected location of burner box, tighten screws just enough to hold brackets in place step C position brackets so that they are with the clamp screw in contact with the counter top bottom

step D tighten attachment screws securely. step E check that the front edge of the cooktop is parallel to

the front edge of the countertop tighten the screw clamping against the countertop.

DO NOT OVER TIGHTEN

4 - Gas Requirement

A QUALIFIED SERVICE MAN OR GAS APPLIANCE INSTALLER MUST MAKE THE GAS SUPPLY CONNECTION.

Leak testing of the appliance shall be conducted by the installer according to the instructions given. You must install the supplied connection parts seen here in this conﬁguration to the main gas manifold on the appliance. Issues arising from a failure to do so will not be covered by warranty. Do not install the pressure regulator backwards as the gas will not ﬂow correctly. Check that the arrow on the back points in the direction of gas ﬂow. Parts required for connection from gas supply to regulator are the responsibility of the installer / owner

Appliance

pressure regulator

Flare union

adaptor

Gasket

Important Notes for Gas Connection

The appliance and its individual gas shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa). The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa). All supply piping, except as noted, should use common National Pipe Thread (N.P.T.). For all pipe connections use an approved pipe joint compound resistant to the action of LP gas. This appliance is designed for use with NG gas or LP gas. The gas pressure regulator is supplied with this appliance. It must be installed in the gas way ahead of the manifold entrance. It is pre-set for use with natural gas. To use it with different gas it must be converted, as described in the Gas conversion paragraph. If at any time the appliance is to be used with a different type of gas, all the conversion adjustments must be made by a qualiﬁed technician before attempting to operate the cooktop on that gas. The gas should be supplied to the appliances pressure regulator, at line pressure between 6 and 14 inches of water column for NG, and between 11 and 14 inches of water column for LP.

ATTENTION

Use Teﬂon tape rated for gas applications at all threaded connections. Do not overtighten the connection at the manifold or you could damage the gasket causing a leak.

WARNING

If the line pressure supplying the appliance pressure regulator exceeds 14 inches W.C. (any gas), an external regulator must be installed in the gas line ahead of the appliance regulator to reduce the pressure to no more than 14 inches W.C. Failure to do this can result in malfunction and damage to the appliance.

GAS REQUIREMENTS

NATURAL GAS WC

Manifold Pressure 5" (12.5 mb) Min Line Pressure 6" (15 mb) Max Line Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

LP GAS WC

Manifold Pressure 10” (25 mb) Min Line Pressure 11” (27.4 mb) Max Line Pressure 14” (34.9 mb), .5 psi (3.5 kPa)

IMPORTANT

• NEVER REUSE OLD CONNECTORS WHEN INSTALLING THIS COOKTOP.

To reduce the likelihood of gas leaks, apply teﬂon tape or a thread compound approved for use with LP or Natural gases to all threaded connections. Apply a non-corrosive leak detection ﬂuid to all joints and ﬁttings in the gas connection between the supply line shut-off valve and the cooktop inlet. Check for leaks! Bubbles appearing around ﬁttings and connections will indicate a leak. If a leak appears, turn off supply line gas shut-off valve, tighten connections, turn on the supply line gas shutoff valve, and retest for leaks. Never test for gas leaks with an open ﬂame.

• NEVER TIGHTEN TO MORE THAN 35 ft lbs OF TORQUE.

Gas Connection

• Thread the appliances pressure regulator with 1/2” male end connection both supplied with this appliance.

• Make the gas connection to the inlet of the pressure regulator with 1/2” male pipe threads.

• Join the pressure regulator to the entrance threads of the Gas Manifold with gasket supplied with this appliance. The regulator is marked with a directional arrow indicating correct direction of gas ﬂow. Ensure the appliance regulator is installed with the arrow pointing toward the gas manifold entrance and make sure the top of the regulator is facing towards the cabinet front, easily accessible through the cabinet doors.

• Connect a manual shut-off valve to the gas supply in an accessible location for turning on or shutting off gas to the appliance.

• Install a coupling between the regulator and the shutoff valve to complete the connection.

• Assure all pipe joint connections are gas tight.

• Check alignment of valves after connecting the cooktop to the gas supply to be sure the manifold pipe has not been moved.

• A misalignment could cause the valve knob stem to rub on the control panel, resulting in a gas leak at the valve.

(REAR OF APPLIANCE)

BURNER BOX

GASKET

FLARE UNION

ADAPTOR

APPLIANCE

PRESSURE

REGULATOR

ALL PIPE JOINTS

1/2" N.P.T.

ILLUSTRATIVE GAS SUPPLY PIPING (NO OTHER APPLIANCE BELOW COOKTOP)

GAS

If an oven is to be installed below this appliance connect gas supply line as shown in ﬁgure consider the below cabinet clearance.

MANIFOLD

SHUTOFF

VA LVES

FOR ALTERNATIVE PIPING METHODS TO CONNECT THE APPLIANCE TO THE GAS SUPPLY, A TRAINED SERVICE MAN OR GAS APPLIANCE INSTALLER MUST MAKE THE GAS SUPPLY CONNECTION. Leak testing of the appliance shall be conducted by the Installer according to the Instructions given.

Unless prohibited by local codes or ordinances, a new A.G.A.

- Certiﬁed, ﬂexible metal appliance connector may be used to connect this appliance to its gas supply. The connector must have an internal diameter not less than nominal 1/2” NPT pipe and be no more than 5 feet in length. A 1/2” NPT x 1/2” ﬂare union adapter is required at each end of the ﬂexible connector. If a ﬂexible connector is used assure that both the appliance pressure regulator and manual shut-off valve are joined solidly to other permanent hard piping (either gas supply or the appliance manifold) so as to be physically stationary. See ﬁgure.

CAUTION

Do not attempt to attach the ﬂexible connector directly to an external pipe thread. Connection requires ﬂare union adapters.

For Massachusetts Installations:

1. Shut-off valve must be a “T” handle gas cock.

2. Flexible gas connector must not be longer than 36 inch.

3. Not approved for installation in a bedroom or a bathroom unless unit is direct vent.

GASKET

FLARE UNION

ADAPTOR

APPLIANCE

PRESSURE

REGULATOR,

SUPPLIED (OBSERVE

DIRECTIONALITY

OF GAS FLOW)

FLARE

UNION

ADAPTOR

FLEXIBLE

APPLIANCE

CONNECTOR

5 FT. MAX

()

(1.52 m) MAX

FLARE

UNION

ADAPTOR

GAS

SHUT-OFF

VA LVE

1/2" NPT PIPE (STATIONARY

SUPPLY PIPE)

NO APPLIANCE

MOUNTED BELOW

THIS COOKTOP

MANIFOLD ENTRANCE

FLARE UNION

GASKET

1/2" NPT

PIPE NIPPLE

ELBOW

PRESSURE REGULATOR,

SUPPLIED (OBSERVE

DIRECTIONALITY

OF GAS FLOW)

1/2" NPT PIPE (STATIONARY

SUPPLY PIPE)

WALL OVEN MOUNTED

ADAPTOR

FLEXIBLE

APPLIANCE

CONNECTOR

5 FT. MAX

()

(1.52 m) MAX

FLARE

UNION

ADAPTOR

APPLIANCE

1/2" NPT

PIPE NIPPLE

GAS

SHUT-OFF

VA LVE

IN CABINETRY BELOW

THIS COOKTOP

Pressure Testing

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa). This appliance, as well as its individual shut-off valve, must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of 1/2 PSIG (3.5 kPa). When checking appliance regulator function, make certain pressure of natural gas supply is between 6 and 14 inches of water column or, if converted for LP gas, between 11 and 14 inches.

THE PRESSURE TESTING SHOULD BE PERFORMED BY MEANS OF THE INJECTOR THREAD ZONE

Gas test inlet

Thread

Pressure Test Method

• Remove grate and burner cap

• Remove aluminum gas spreader

• Temporarily remove the injectors

• Connect the pressure Test instrument into injector holder thread zone (M6x0,75)

• Check if the cooktop has the correct pressure

• Fix the injector removed for testing and replace the parts in the right position.

5 - Electrical Requirements

General Information

This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on the rating plate. We recommend you have the electrical wiring and hookup of your cooktop connected by a qualiﬁed electrician. After installation, have the electrician show you where your main cooktop disconnect is located. Check with your local utilities for electrical codes which apply in your area. Failure to wire your cooktop according to governing codes could result in a hazardous condition. If there are no codes, your cooktop must be wired and fused to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70 - Latest edition.

You can get a copy by writing:

National Fire Protection Association Battery march Park Quincy. MA 02269

In Canada your cooktop must be wired and fused to meet the requirements of the Canadian Electrical Code. Be sure the installation of this product in a mobile home conforms with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280. If this standard does not apply, you must follow the standard for Manufactured Home Installations, ANSI A225.1 and Manufactured Home Installations, Sites and Communities and ANSI/NFPA 501A or with local codes.

You can get a copy of the Federal Standard by Writing:

Ofﬁce of Mobile Home Standards HUD Building 451 7th Street, S.W. Washington, D.C. 24010

Electrical Connection

An adequate electrical supply and outlet must be used to operate the electrical parts of your cooktop.

CAUTION

Electrical Grounding Instruction

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, ﬁre, or electrical shock.

IMPORTANT

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

The power cord of this appliance is equipped with a 3prong (grounding) plug which must be used with a properly grounded 3-hole outlet with a standard 120 Volt, 60 cycle AC household current. If you do not have a 3-hole grounded outlet, have a qualiﬁed electrician change your old one. A grounding adaptor will be needed to convert the old one until the outlet can be replaced. This method is only temporary, and a qualiﬁed electrician should test it to be sure it meets requirements.

LOCATION OF RATING PLATE

Electrical Requirements

Do not under any circumstances cut or remove grounding prong from the cooktop cord.

GROUNDING PRONG

WIRING DIAGRAM (4 ZONES)

OUT

RE-IGNITER

SYSTEM

G N L

TERMINAL

BLOCK

WIRING DIAGRAM (5 ZONES)

OUT

RE-IGNITER

SYSTEM

G N L

TERMINAL

BLOCK

6 - Conversion for LP or NG Gas

Converting Appliance for Use with LP Gas

WARNING

Conversion is to be performed by a AUTHORIZED SERVICER (or other qualiﬁed agency) in accordance

with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. The qualiﬁed agency performing this work assumes responsibility for this conversion.

WARNING

Before proceeding with the conversion, shut off the gas supply to the appliance prior to disconnecting the electrical power

If this appliance should be converted for use with gas LP (propane or butane), each of the following modiﬁcation must be performed: Gas conversion label (aluminium) to be placed on the back of the appliance, near the data plate, after conversion has been carried out;

Replace injectors on (two rings ﬂame burner)

1. Remove the grates and burner cups.

2. Remove aluminium gas spreader.

3. Remove the three screws of simmer gas spreader (1).

4. Remove the two screws of injector cover (2).

5. Loosen injector (A) by turning 9-32” (7 mm) nut driver counter clockwise.

6. Loosen injector (B) by turning 9-32” (7 mm) box wrench counter clockwise.

7. Install the injectors supplied with this appliances in the appropriate burner. The injectors have small number stamped on the side, this number codes the oriﬁce diameter and its correct burner location (see ﬁgure of the paragraph “Injectors position”).

8. Turn clockwise to tighten (tighten to a torque of 15 to 20 inch-lbs).

9. Replace all parts following the reverse order.

10. Save the injectors removed from the appliances for future use.

Replace injector on (one ring ﬂame burners)

1. Remove the grates and burner cups.

2. Remove aluminum gas spreader.

3. Loosen injector by turning 9-32” (7 mm) nut driver counter clockwise.

4. Install the injectors supplied with this appliances in the appropriate burner. The injectors have small number stamped on the side, this number codes the oriﬁce diameter and its correct burner location (see ﬁgure on page 17).

5. Turn clockwise to tighten (tighten to a torque of 15 to 20 inch-lbs).

6. Replace all parts following the reverse order.

7. Save the oriﬁces removed from the appliance for future use.

After injectors replacement adjust the burner ﬂame (see Low Flame Adjustment paragraph). Check the appearance of each burner’s ﬂame at HILO settings, if the ﬂame appear too large or too small make sure that all steps were completed correctly.

Convert the pressure regulator on LP position following the illustration.

Converting Appliances for Use with NG Gas

If this appliance should be converted for use with gas NG (natural gas), each of the following modiﬁcations must be performed.

1. Replace all injectors following the step described on page 15, observe the number stamped on the side, this number codes the oriﬁce diameter and its correct burner location (following the illustration of injectors position).

2. Convert the pressure regulator on LP position (following the illustration of pressure regulator conversion).

3. Adjust the burner ﬂame (see Low Flame Adjustment paragraph).

Check the appearance of each burner’s ﬂame at HILO settings, if the ﬂame appears too large or too small make sure that all steps were completed correctly.

Pressure regulator conversion

The appliances is designed for use with NG gas or LP gas. The gas pressure regulator is supplied. It must be installed in the gas way ahead of manifold entrance. It is pre-set for use with the gas supplied with the appliances. For use with different gas must be converted.

For the pressure regulator conversion following the below instructions:

• Disconnect all electrical power, at the main circuit breaker or fuse box.

• Shut off the gas supply to the cooktop by closing the manual shut-off valve.

• Adjust the pressure regulator, by following the instruction (see ﬁgure)

1. Unscrew the regulator cap

2. Unscrew the plastic conversion plug from the cap turn over and screw back (wide section away from cap for LP and against cap for NG) see ﬁgures below.

3. Replace the cap regulator.

PRESSURE REGULATOR CONVERSION

Before replace the regulator cap. Check the position of plug. Suitable for the gas converted.

Injectors position

MAIN FLAME

SIMMER

MAIN FLAME

SIMMER

MAIN FLAME

NG LP conversion

Inj-pos-24

SIMMER

180

114

180

160

139

114

Inj-pos-30

Inj-pos-36

SIMMER

115

105

SIMMER

139

114

180

160

115

105

Inj-pos-42

139

180

MAIN FLAME

SIMMER

115

+ 47 hidden pages