Fujitsu L21T-1 Owners Manual

FUJITSU Display L21T-1

Congratulations on your purchase of an innovative

product from Fujitsu.

Latest information about our products, tips, updates etc. can be found on the Internet at:

http://www.fujitsu.com/fts/

For driver updates, please go to: http://support.ts.fujitsu.com/download

Should you have any technical questions, please contact:

● our Hotline/Service Desk (see Service Desk list or visit:
http://support.ts.fujitsu.com/contact/servicedesk)

● your sales partner

● your sales office

We hope you enjoy working with your new Fujitsu system!

Published by / Contact address in the EU

Fujitsu Technology Solutions GmbH

Mies-van-der-Rohe-Straße 8

80807 Munich, Germany

http://www.fujitsu.com/fts/

Copyright

© Fujitsu Technology Solutions GmbH 2015. All rights reserved.

Publication Date

07/2015

Order No.: A26361-K1575-Z320-1-7619, edition 1

FUJITSU Display L21T-1

Operating Manual

First Setup 2

Quick Installation 3

Installing the LCD 5

Front view of the product 7

Rear view of the product 8

Using On Screen Display (OSD) 9

Supporting Timing Modes 13

Remarks

Information on the product description meets the design specifications of Fujitsu and is
provided for comparison purposes. Several factors may cause the actual results to differ.
Technical data is subject to change without prior notification. Fujitsu rejects any responsibility
with regard to technical or editorial mistakes or omissions.

Trademarks

Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited or its subsidiaries in
the United States and other countries.

Microsoft and Windows are trademarks or registered trademarks of the Microsoft Corporation
in the United States and/or other countries.

VESA, DDC and DPMS are registered trademarks of Video Electronics Standards
Association.

All other trademarks specified here are the property of their respective owners.

Copyright

No part of this publication may be copied, reproduced or translated without the prior written
consent of Fujitsu.

No part of this publication may be saved or transferred by any electronic means without the
written approval of Fujitsu.

Contents

Contents

First Setup........................................................................................................................................... 2

Quick Installation................................................................................................................................3

Installing the LCD monitor................................................................................................................. 5

Assembling the stand and base ........................................................................................................... 5

Disassembling the stand and base....................................................................................................... 6

Front view of the product................................................................................................................... 7

Rear view of the product.................................................................................................................... 8

Using On Screen Display (OSD) functions....................................................................................... 9

Main Menu............................................................................................................................................ 9

Shortcut functions from the button(s) ................................................................................................. 10

Automatic adjustment................................................................................................................. 10

Adjusting brightness and contrast .............................................................................................. 10

Adjusting the input...................................................................................................................... 10

Adjusting the audio functions ..................................................................................................... 10

Adjusting the colour.................................................................................................................... 11

Displaying information ................................................................................................................ 11

Adjusting the image.................................................................................................................... 11

Adjusting the OSD setup ............................................................................................................ 12

Adjusting the factory settings ..................................................................................................... 12

Supporting Timing Modes ............................................................................................................... 13

Warning .............................................................................................................................................. 13

Fujitsu 1

First Setup

First Setup

Congratulation for purchasing monitor! This monitor comes with the following accessories:

Power cable

•

Audio cable

•

DVI cable (24 pin)

•

Quick Start Guide

•

Safety manual

•

2 Fujitsu

Quick Installation

Quick Installation

1 32 4 5

1 = Power cable
2 = Headphones (optional)
3 = DVI cable

► Make sure that both monitor and computer are OFF.

►

Connect the video cable (VGA cable) to the computer, then to the monitor.

► Connect the DVI cable from the DVI output on the computer to the DVI input on the monitor.

► Connect the power cable to a properly grounded AC outlet, then to the monitor.

► Connect the headphones to the headphone output terminal of the monitor (headphones sold

separately).

► Connect the audio cable from the audio output of your computer to the audio input of the

monitor.

► Turn the computer power on.

► Turn the monitor power on.

Fujitsu 3

4 = AUDIO cable (optional)
5 = VGA cable

Quick Installation

► Set the timing mode (resolution and refresh rate):

For Windows users

Example: 1920 x 1080 @ 60 Hz

Resolution

– Right-click on the Windows desktop and select

– Set the resolution.

Refresh rate (vertical frequency)

– See your graphic card’s user guide for instructions.

Screen Resolution.

4 Fujitsu

Installing the LCD monitor

Installing the LCD monitor

Assembling the stand and base

► To prevent the monitor from being scratched, put a piece of soft cloth on the table on which the

screen will be put.

Lay the monitor flat on a table with the LED screen face down.

►

► Insert the stand and base into the monitor as shown below.

► Stand the LED LCD monitor on its base.

Fujitsu 5

Installing the LCD monitor

Disassembling the stand and base

► To prevent the monitor from being scratched, put a piece of soft cloth on the table on which the

screen will be put.

Lay the monitor flat on a table with the LED screen face down.

►

► Press the release button and pull the stand away from the monitor.

► Push the tabs inwards and pull the base from the stand to remove.

6 Fujitsu

Front view of the product

Front view of the product

1234 65

1 = OSD menu ON/OFF
2 = Scroll down / Decrease
3 = Scroll up/ Increase

Fujitsu 7

4 = Confirm/Select
5 = Power ON/OFF
6 = LED indicator

Rear view of the product

Rear view of the product

1234 5

1 = Power input
2 = Headphone jack
3 = Audio input

8 Fujitsu

4 = DVI input (DVI 24 pin)
5 = VGA input (D-Sub 15 pin)

Using On Screen Display (OSD) functions

Using On Screen Display (OSD) functions

Displays main menu 1

Exits OSD menu

Toggles between VGA or DVI 2

Confirms selection

Selects the desired item when in OSD menu ▼

When not in OSD menu, opens the Brightness/Contrast menu

Selects the desired item when in OSD menu ▲

When not in OSD menu, directly enters Image Mode

1+▼ Power lock (when not in OSD menu)

1+▲ OSD lock (when not in OSD menu)

Main Menu

Fujitsu 9

Using On Screen Display (OSD) functions

Shortcut functions from the button(s)

Automatic adjustment

Automatically adjusts Horizontal Position, Vertical Position,
Phase (Fine Tune) and Clock (H. Size) of the screen.

Adjusting brightness and contrast

Calls up the

Contrast Adjusts the contrast of the screen.

▲: Increase contrast.

▼: Decrease contrast.

Brightness Adjusts the brightness of the screen.

▲: Increase brightness.

▼: Decrease brightness.

ACR Allows the user to turn ACR on or off. Brightness adjustment

and ECO are disabled when ACR is active.

ECO Allows the user to turn ECO on or off. Brightness adjustment

and ACR are disabled when ECO is active.

Brightness/Contrast setting window

Adjusting the input

When Input Select is selected, change the input signal to VGA
or DVI.

Adjusting the audio functions

Adjusts the

Volume Adjusts the speaker output volume.

Mute Turns the Mute on or off.

audio functions.

10 Fujitsu

Using On Screen Display (OSD) functions

Adjusting the colour

Selects the
between 9300K, 6300K, 5400K and customer colour.

9300K Adds more blue to the picture, for a cooler white.

6300K Adds more red to the picture, for a warmer white and richer

reds.

5400K Adds more green to the picture, for darker tones.

Customer color Individual adjustments for red (R), green (G), blue (B).

► Press button 2 to select the desired colour.

► Press the ▲ or ▼ button to adjust the selected colour.

color to improve brightness and colour saturation

Displaying information

Displays the
coming from the graphic card in your computer.

Note: See your graphic card user guide for more information
about changing the resolution and refresh rate.

information regarding the current input signal

Adjusting the image

Manually adjusts the H./V. position, horizontal size, phase,
sharpness, expansion and mode

H./V. Position Adjusts the horizontal and vertical position of the image.

H. Position ▲: Move screen to the right.

▼: Move screen to the left.

V. Position ▲: Move screen up.

▼: Move screen down.

Horizontal size Adjusts the width of the screen image.

▲: Increase the width of screen image.

▼: Decrease the width of screen image.

Phase Adjusts the delay time of data and clock.

Press ▲ or ▼ to adjust to your preference.

Sharpness Adjusts the clarity of a non-Full HD resolution (1920 x 1080)

Expansion Toggles the video mode between Full Screen or Aspect

Full Screen Selects full-screen image.

KeepAspect Selects input timing image size.

signal with the ▲ or ▼ button.

Ratio

Fujitsu 11

Using On Screen Display (OSD) functions

Mode Provides an optimum display environment depending on the

Standard is for the general Windows environment and the monitor

Game optimised for a PC game environment

Video optimised for a movie and video environment.

Landscape optimised to display outdoor scenery images.

Text optimised for text editing and viewing in a word processing

contents displayed. It contains 5 user-selectable presets.

default setting.

environment

Adjusting the OSD setup

Sets Language, OSD Position, OSD time Out and OSD
Background.

Language Allows users to choose from the languages available.

OSD Position Press the ▲ or ▼ button to toggle between horizontal and

H. Position Horizontally adjusts the OSD position.

V. Position Vertically adjusts the OSD position.

OSD time Out Automatically turns off On Screen Display (OSD) after a

OSD Background Allows the user to turn the OSD background ON or OFF.

vertical OSD position adjustment.

▲: Move OSD to the right.

▼: Move OSD to the left.

▲: Move OSD up.

▼: Move OSD down.

preset period of time.

Adjusting the factory settings

Restores factory settings for Video or Audio controls.

12 Fujitsu

Press button 2 to select the Memory Recall menu option.

Supporting Timing Modes

Supporting Timing Modes

Resolution Refresh rate

640 x 480 60/67/72/75Hz

720 x 400 70 Hz

800 x 600 60/75 Hz

832 x 624 75 Hz

1024 x 768 60//70/75 Hz

1280 x 800 60 Hz

1280 x 960 60 Hz

1280 x 1024 60/75 Hz

1152 x 864 75 Hz

1152 x 870 75 Hz

1440 x 900 60/75 Hz

1600 x 1200 60 Hz

1680 x 1050 60 Hz

1920 x 1080 60 Hz

Do not set the graphic card in your computer to exceed these maximum refresh

!

rates. Doing so may result in permanent damage to your monitor.

Warning

This display is equipped with a glossy front bezel.

!

Please consider the placement of the display as the front bezel may cause reflections from
surrounding light and bright surfaces.

Fujitsu 13