P3PC-1582-01EN
fi-5015C Image Scanner
Getting Started
CONTENTS
■ Regulatory Information ........................................................ ii
■ Note, Liability ....................................................................... iii
■ Safety Precautions ................................................................ v
Chapter1 PREPARING THE SCANNER.................................. 1
1.1 Checking the Contents of the Scanner Package............. 1
1.2 Names of Parts ................................................................... 1
1.3 Operator panel.................................................................... 1
Chapter2 INSTALLATION OF THE SCANNER....................... 3
2.1 Installing the Scanner Application ................................... 3
2.2 Installing the Scanner ........................................................ 9
2.3 Connecting the Scanner to Your PC............................... 10
2.4 Confirming Installation .................................................... 11
Appendix1 TROUBLESHOOTING........................................ AP-1
Appendix2 DAILY CARE ...................................................... AP-4
Appendix3 REPLACING CONSUMABLES.......................... AP-5
fi-5015C Image Scanner Getting Started i
INTRODUCTION
Thank you for purchasing the fi-5015C Color Scanner.
This document describes how to use fi-5015C and basic
operation methods. Before you start using fi-5015C be
sure to thoroughly read this manual to ensure correct
use.
The "Operator’s Guide" stored on the Setup CD Rom
provides useful and detailed information on Operations
when you would like to use advanced features, Daily
Care for maintenance of the scanner, and Replacing
Consumables to maintain conditions for smooth scanning. Please also read the Operator’s Guide for further
information.
■ Regulatory Information
FCC declaration
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
located.
• Consult your dealer or an experienced radio/TV
technician.
FCC warning: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTICE
The use of a shielded interface cable is
required to comply with the Class B limits
of Part 15 of FCC rules.
The length of the AC cable must be 3
meters (10 feet) or less.
Canadian DOC Regulations
This digital apparatus does not exceed the Class B
limit for radio noise emissions from digital
apparatus set out in the Radio interference
Regulations of the Canadian Department of
Communications.
This Class B digital apparatus complies with
Canadian ICES-003.
Le présent appareil numérique n'émet pas de
parasites radioélectriques dépassant les limites
applicables aux appareils numériques de la classe
B et prescrites dans le Règlement sur le brouillage
radioélectrique dictées par le Ministère des
Communications du Canada.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
Bescheimigung des Herstellers /
Importeurs
Für den fi-5015C wid folgendes bescheinigt:
• In Übereinsstimmung mit den Bestimmungen
der EN45014(CE) funkentstört
• Maschinenlärminformationsverordnung
3.GPSGV: Der höchste Schalldruckpegel beträgt
70 dB (A) oder weniger, gemäß EN ISO 7779.
International ENERGY STAR® Program
As an ENERGY STAR®
Partner, PFU LIMITED has
determined that this product
meets the
guidelines for energy efficiency.
The International
STAR
international program that promotes energy
saving through the penetration of energy efficient
computers and other office equipment. The
program backs the development and
dissemination of products with functions that
effectively reduce energy consumption. It is an
open system in which business proprietors can
participate voluntarily. The targeted products are
office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and
multifunction devices. Their standards and logos
are uniform among participating nations.
ENERGY STAR
ENERGY
®
Office Equipment Program is an
®
ii
■ Note, Liability
READ ALL OF THIS MANUAL CAREFULLY
BEFORE USING THIS PRODUCT. IF THIS
PRODUCT IS NOT USED CORRECTLY,
UNEXPECTED INJURY MAY BE CAUSED TO
USERS OR BYSTANDERS.
• Do not put the substance contained in the lamp
in your mouth as it has mercury.
• Do not breathe the chemical liquid contained in
the scanner lamps.
• Do not incinerate, crush, or shred the lamps or
scanner parts.
Also, keep this manual in a safe place so that it
can be easily referred to during use of this
product.
While all efforts have been made to ensure the
accuracy of all information in this manual, PFU
assumes no liability to any party for any damage
caused by errors or omissions or by statements of
any kind in this manual, its updates or
supplements, whether such errors are omissions or
statements resulting from negligence, accidents,
or any other cause. PFU further assumes no
liability arising from the application or use of any
product or system described herein; nor any
liability for incidental or consequential damages
arising from the use of this manual. PFU disclaims
all warranties regarding the information contained
herein, whether expressed, implied, or statutory.
Use in High-safety Applications
This product has been designed and manufactured
on the assumption that it will be used in office,
personal, domestic, regular industrial, and
general-purpose applications. It has not been
designed and manufactured for use in applications
(simply called "high-safety applications" from
here on) that directly involve danger to life and
health when a high degree of safety is required,
for example, in the control of nuclear reactions at
nuclear power facilities, automatic flight control
of aircraft, air traffic control, operation control in
mass-transport systems, medical equipment for
sustaining life, and missile firing control in
weapons systems, and when provisionally the
safety in question is not ensured. The user should
use this product with adopting measures for
ensuring safety in such high-safety applications.
PFU LIMITED assumes no liability whatsoever
for damages arising from use of this product by
the user in high-safety applications, and for any
claims or compensation for damages by the user
or a third party.
About the use of mercury
Lamp(s) inside this product contain
H
g
mercury and must be recycled or
disposed of according to local, state, or
federal laws.
Trademarks
Microsoft, Windows, and Windows NT are
registered trademarks of Microsoft Corporation in
the United States and/or other countries.
ISIS, QuickScan and their respective logos are
trademarks or registered trademarks of EMC
Corporation in the United States.
Adobe, the Adobe logo, and Acrobat are either
registered trademarks of Adobe Systems
Incorporated in the United States and/or other
countries.
Other product names are the trademarks or
registered trademarks of the respective companies.
How Trademarks Are Indicated In
This Manual
References to operating systems (OS) are
indicated as follows:
Windows 98
Windows Me
Windows 2000
Windows XP
Where there is no distinction between the different
versions of the above operating system, the
general term "Windows " is used.
Adobe Acrobat
All the descriptions in this manual assume the
usage of Adobe Acrobat bundled with this
product. However, Adobe Acrobat may be
upgraded without notice. If the descriptions differ
from the screens actually displayed, refer to the
Acrobat’s “Help”.
Microsoft® Windows® 98
operating system.
Microsoft® Windows®
Millennium Edition operating
system.
Microsoft® Windows® 2000
Professional operating system.
Microsoft® Windows® XP
Professional operating system,
Microsoft
Edition operating system.
®
Windows® XP Home
Adobe® Acrobat®
To avoid unexpected injuries;
fi-5015C Image Scanner Getting Started iii
Manufacturer
PFU LIMITED
International Sales Dept., Imaging Business
Division, Products Group
Solid Square East Tower, 580 Horikawa-cho,
Saiwai-ku, Kawasaki-shi Kanagawa 212-8563,
Japan
Phone : (81-44) 540-4538
All Rights Reserved, Copyright© PFU LIMITED 2006
Outline characters on a colored background
show instructions users should follow.
R
It may also include the drawing that shows the
specific instruction.
Warning Label
The glass surface inside the ADF becomes hot
during the operation. Be careful not to touch the
glass surface inside the ADF.
About Maintenance
The user must not perform repairs on this scanner.
Contact the store where you purchased the scanner
or an authorized FUJITSU Image Scanner service
provider to make repairs to this product.
Warning Indications Used In This
Manual
This indication alerts operators to an
WARNING
CAUTION
operation that, if not strictly
observed, may result in severe injury
or death.
This indication alerts operators to an
operation that, if not strictly
observed, may result in safety
hazards to personnel or damage to
equipment.
Symbols Used In This Manual
ATTENTION
Do NOT remove, stain or scratch the
warning labels from the scanner.
Screen Examples In This Manual
The screen examples in this manual are subject to
change without notice in the interest of product
improvement. If the actual displayed screen
differs from the screen examples in this manual,
operate by following the actual displayed screen
while referring to the User's Manual of the scanner
application you are using.
The screenshots in this manual were captured
from FUJITSU TWAIN32 scanner driver,
ScandAll 21 Image Capturing Utility Software,
FUJITSU ISIS scanner driver, QuickScan Pro™
image capturing software and Adobe Acrobat.
ATTENTION
HINT
This symbol alerts operators to particularly
important information. Be sure to read this
information.
This symbol alerts operators to helpful
advice regarding operation.
A TRIANGLE symbol indicates that special care
and attention is required.
The drawing inside the triangle shows the
specific caution.
A CIRCLE with a diagonal line inside shows
action which users may not perform.
The drawing inside or under the circle shows the
specific action that is not allowed.
iv
■ Safety Precautions
WARNING
Turn the scanner OFF if it is damaged.
If the scanner is damaged for any reason,
disconnect immediately the power plug in order
to turn out the scanner. Contact the store
where you purchased the scanner.
Do not damage the AC cable.
A damaged AC cable may cause fire or electric
shock. Do not place heavy objects on AC
cables, or pull, bend, twist, heat, damage or
modify AC cables.
Do not use damaged AC cables or power
plugs, or install any cables or power plugs to
loose wall sockets.
Use only specified AC cables and
connector cables
Use only specified AC cables and connector
cables. Failure to use the correct cables might
cause electric shock and/or equipment failure.
Please don’t use the AC cable provided with
this scanner for other devices, since this might
cause equipment failure and other troubles or
an electric shock.
Use this scanner only at the indicated
power voltage. Do not connect to multiplepower strips.
Use this scanner only at the indicated power
voltage and current. Improper power voltage
and current might cause fire or electric shock.
Do not connect to multiple-power strips.
Do not touch the AC cable with wet hands.
Do not touch the power plug with wet hands.
Doing so might cause electric shock.
Do not put liquids inside the scanner.
Do not insert or drop metal objects in to the
scanner. Do not scan wet documents or
documents with paper clips or staples. Do not
splash or allow the scanner to get wet.
If foreign objects (water, small metal objects,
liquids, etc.) get inside the scanner, immediately
turn off the scanner and disconnect the power
plug from the power outlet, then contact the store
where you bought the scanner or the
Maintenance Service Center. Pay particular
attention to this warning in households where
there are small children.
Do not touch the inside of the scanner
unless necessary.
Do not take apart or modify the scanner. The
inside of the scanner contains high-voltage
components. Touching these components might
cause fire or electric shock.
Do not use the scanner if there is a strange
odor.
If you detect excessive heat coming from the
device or detect other problems such as smoke,
strange smells or noises, disconnect immediately
the power plug in order to turn out the scanner.
Make sure that any smoke coming from it has
stopped, before contacting the store where you
bought the scanner or an authorized FUJITSU
scanner service provider.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the
power plug or metal fittings with a soft, dry
cloth. Accumulated dust might cause fire or
electric shock.
Do not install the device in locations that
has oil smoke, steam, humidity, and dust.
Do not install the scanner in locations subject
to oil smoke, steam, humidity, and dust. Doing
so might cause a fire or electric shock.
fi-5015C Image Scanner Getting Started v
CAUTION
Do not install the scanner on unstable
surfaces.
Make sure that the scanner is installed on a
flat, level surface and that none of its parts
extend beyond the surface top, such as a desk
or table. Do not install the scanner on
unstable surfaces. Install the scanner on a level
surface that is free of vibration to prevent it
from falling.
Install the scanner on a strong surface that will
support the weight of the scanner and other
devices.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the
ventilation ports generates heat inside of
scanner, which may results in fire or scanner
failure.
Do not place heavy objects or stand on top
of the scanner.
Do not place heavy objects on the scanner or
use the scanner's surface top to perform other
work. Improper installation might cause injuries
and equipment failure.
Firmly insert the power plug.
Firmly insert the power plug as far it can go into
the power outlet.
Avoid any contact when scanner is in use.
Avoid touching any scanner mechanism during
scanning since this may cause injuries.
Before moving the scanner, disconnect the
power plug from the power outlet.
Do not move the scanner with the power and
interface cables connected as this might
damage the cables, causing fire, electric shock
or injuries. Before moving the scanner, be sure
to disconnect the power plug from the power
outlet, and all other data cables. Make sure that
the floor is free of any obstruction.
Protect the scanner from static electricity.
Install the scanner away from strong magnetic
fields and other sources of electronic noise.
Also, protect the scanner from any static
electricity as this might cause the scanner to
malfunction.
Do not use aerosol sprays near the
scanner.
Do not use aerosol sprays to clean the scanner.
Aerosol sprays cause dirt and dust to enter the
scanner, resulting scanner failure and
malfunction.
Disconnect the power plug from the power
outlet when the scanner is not used for a
long period of time.
When the scanner is not going to be used for a
long period of time, be sure to disconnect the
power plug from the power outlet for safety.
Do not install the scanner in the direct
sunlight.
Do not install the scanner under direct sunlight or
near heating apparatus. Doing so might cause
excessive heat to build up inside the scanner,
which can cause scanner trouble or even fire.
Install the scanner in a well-ventilated location.
Do not use the scanner immediately after
moving it from a cold place into a warm
room.
Do not use the device immediately after
moving it from a cold place into a warm room.
This may cause condensation, which might
lead to scanning errors. Let the device dry
about one or two hours before you use it.
vi
Before moving the scanner, make sure the
shipping lock is locked.
When moving the scanner, be sure to lock the
shipping lock in order to prevent damages to
the scanner.
Chapter1 PREPARING THE SCANNER
1.1 Checking the Contents of the Scanner Package
When you unpack the scanner package, make sure that
the package contains all the parts on the list included in
the package.
If any parts are missing or defective, contact your scanner dealer or an authorized FUJITSU scanner service
provider. Handle the scanner and accessories with care.
1.2 Names of Parts
This section describes the names of parts.
Side Guide
ADF paper chute
Automatic Document Feeder (ADF)
Extension
Document cover
Document
stopper
Flatbed
Operator panel
1.3 Operator panel
The operator panel is located on the front side of the
scanner. The panel consists of a Function Number Display, four buttons and a LED.
(1)
.
Function Number
Display (2)
Buttons
Power LED(5)
(2)
Name Function
Function (1)
Send to (3)
Scan (4)
Power button
(6)
(3)
Indicates the state of the scanner. The meaning of the numbers and alphabets indicated are
explained later in this section.
Changes the Function activated
by the Send to button.
Launches the linked application
software (*).
Turns the scanner ON and OFF.
Lights when the scanner is
turned ON.
(4)
(5)
(6)
USB connector
ADF cable connector
*) About the settings on the launcher, refer to FUJITSU
TWAIN32 scanner driver help and the "fi-5015C
Operator’s Guide" on the Setup CD-ROM.
Shipping lock
Main power switch
DC inlet
fi-5015C Image Scanner Getting Started 1
■ Indications on the Function
Number Display
The following shows the indications on the Function
Number Display.
No. Descriptions
8
P
0
1
U
E
Lights only one time upon turning on the scanner.
Indicates that the scanner has been turned ON and
is being initialized.
Indicates that initialization will soon be completed.
Indicates that initialization has been completed
successfully.
This status is called "Ready Status".
Indicates that a temporary error (that users can
solve) has occurred during the initialization or
scanning of documents.
"U" and an error number (0, 1, 9) are displayed
alternately. Refer section "Temporary error" on
page. AP-3.
To return the scanner to the ready status ("1"),
press the "Scan" or "Send to" button while the
error is indicated. Refer section "Temporary error"
on page. AP-3.
Indicates that a device alarm (that users can not
solve) has occurred during the initialization or
scanning of documents.
"E" and an alarm number (0, 2 ,7, b, c, d) are indicated alternately.
To return the scanner to the ready status ("1"),
press "Scan" or "Send to" button.
If this alarm occurs, turn the power off and then on
again. If the alarm is indicated after turning on the
power again, contact your service engineer.
2
Chapter2 INSTALLATION OF THE SCANNER
2.1 Installing the Scanner Application
For scanning documents with this scanner, both scanner
driver and image capturing application software (called
"application" hereafter) must be installed on your PC.
The following scanner drivers and applications are provided:
• Scanner Driver:
FUJITSU TWAIN 32 Scanner Driver
FUJITSU ISIS Scanner Driver
• Scanning application:
ScandAll 21 (for FUJITSU TWAIN 32)
QuickScan Pro
Install the appropiate scanner driver for the application
you will use. The following sections describe installation of each driver and application.
ATTENTION
Please install the scanner driver before
connecting the scanner to your PC.
If you connect the scanner before installing the scanner driver, the scanner will not
operate correctly.
If you have connected the scanner beforehand, the "Found New Hardware Wizard"
screen appears (this screen might differ
slightly according to the used OS) . On this
screen, click the [Cancel] button to close
the Wizard screen and install the scanner
driver first.
TM
(Trial) (for FUJITSU ISIS )
■ Installing the FUJITSU TWAIN32
Scanner Driver
ATTENTION
1. Turn on your PC and log on to Windows.
ATTENTION
2. Insert the Setup CD-ROM into the CD drive.
⇒ <SETUP DISK START UP SCREEN> appears.
ATTENTION
3. Click [INSTALL PRODUCTS].
Windows XP screenshots are used in this
section as examples. The windows and
operations may slightly vary depending on
your OS
When using Windows 2000 or Windows
XP, log on as a user with "Administrator"
privileges.
This screen may not appear when the
"Autoplay" setting of your PC is OFF. In
this case, run "Install.exe" in this CD-ROM
directly from the "Explorer" or "My Computer".
.
For FUJITSU TWAIN32 Scanner Driver
■ Preparation
Confirm the following items before installing the application.
• Take out the Setup CD-ROM from its package, but do not insert the Setup CD-ROM
into the CD driver yet.
• Uninstall any older version of FUJITSU
TWAIN 32 driver if already installed.
ATTENTION
Uninstall [Scanner Utility for Microsoft Windows] from [Add/Remove Programs] of the
control panel.
fi-5015C Image Scanner Getting Started 3
4. Click [TWAIN Driver] on the window below.
5. Error Recovery Guide Installation window
appears.
Error Recovery Guide is a software that displays troubleshooting information on screen
when any scanner error occurs. Although this
software’s installation is highly recommended,
it can be installed later if you do not install it in
this step.
■ Installing ScandAll 21
"Scandall 21" is an image capturing software that complies with the TWAIN standard.
ATTENTION
When using Windows 2000 or Windows
XP, log on as a user with "Administrator"
privileges.
ATTENTION
When you select [Yes] for installing the
Error Recovery Guide, [Choose Setup
Language] window appears. Select a language and follow the instructions on the
window. Error Recovery Guide will automatically continue finishing its installation.
Please wait until the installation of TWAIN
driver automatically starts.
6. Select a language used for installation on
[Choose Setup Language] window and click
[OK].
7. Follow the instructions on the window to install
the application.
1. Insert the Setup CD-ROM into the CD drive.
⇒ <SETUP DISK START UP SCREEN> appears.
2. Click [INSTALL PRODUCTS].
3. Click [ScandAll 21] on the window below.
8. When the [InstallShield Wizard Complete] window appears, click [Finish].
Your computer will be restarted.
Do not remove the Setup CD-ROM from the CD drive
until your PC has completely restarted.
Installation of the scanner driver is completed.
4. Select a language used for installation on
[Choose Setup Language] window and click
[OK].
5. Install the application following the instructions
on the window.
4
6. When the [InstallShield Wizard Complete] window appears, click [Finish].
3. Click [INSTALL PRODUCTS].
4. Click [ISIS Driver] on the window below.
ATTENTION
For finishing the installation, it may be necessary to restart your computer. Follow the
instructions on the window.
For FUJITSU ISIS Scanner Driver
■ Preparation
Take out the Setup CD-ROM from its package, but do
not insert the Setup CD-ROM into the CD drive yet.
■ Installing the FUJITSU ISIS
Scanner Driver
ATTENTION
1. Turn your PC on and log on to Windows.
ATTENTION
Windows XP screenshots are used in this
section as examples. The windows and
operations may vary slightly depending on
your OS.
When using Windows 2000 or Windows
XP, log on as a user with "Administrator"
privileges.
5. Error Recovery Guide Installation window
appears.
Error Recovery Guide is a software that displays troubleshooting information on screen if
any scanner error occurs. Although this software’s installation is highly recommended, it
can be installed later if you do not install it in
this step.
ATTENTION
When you select [Yes] for installing Error
Recovery Guide, the [Choose Setup Language] window appears. Select a language and follow the instructions on the
window. The Error Recovery Guide will
automatically continue finishing its installation. Please wait until the installation of
ISIS driver automatically starts.
2. Insert the "Setup CD-ROM" into the CD drive.
⇒ <SETUP DISK START UP SCREEN> appears.
ATTENTION
This screen may not appear when the
"Autoplay" setting of your PC is OFF. In
this case, run "Install.exe" in this CD-ROM
directly from the "Explorer" or "My Computer".
fi-5015C Image Scanner Getting Started 5
6. Select a language used for installation on
[Choose Setup Language] window and click
[OK].
7. Follow the instructions on the window to install
the application.
8. When the [InstallShield Wizard Complete]
window appears, click [Finish].
Your computer will be restarted. Do not remove the
Setup CD-ROM from the CD drive until your PC has
completely restarted.
Now the installation of the scanner driver is completed.
■ Installing QuickScan Pro™(Trial)
"QuickScan Pro™ (Trial)" is an image capturing software that complies with the ISIS standard.
ATTENTION
1. Insert the Setup CD-ROM into a CD drive.
⇒ <SETUP DISK STARTUP SCREEN> appears.
• When using Windows 2000 or Windows
XP, log on as a user with "Administrator"
privileges.
5. Enter the required information, then click
[Next >] button.
2. Click [INSTALL PRODUCTS].
3. Click [QuickScan PRO (Trial)] on the window
below.
ATTENTION
"QuickScan Pro™" included in the Setup
CD-ROM is a trial version. For further use
after the expiration of its trial period of up
to 30 launches, it is necessary to purchase
a fully functional version of QuickScan
Pro™. (When you install the trial version,
do not change the Serial Number already
displayed.)
6. Install the application following the instructions
on the window.
Error Recovery Guide
Error Recovery Guide is a software that displays troubleshooting information on screen if any scanner error
occurs.
If you did not install together the Error Recovery Guide
4. Continue to install the application following the
instructions on the window.
with the driver, please proceed with the procedures
given below for installing it.
1. Insert the Setup CD-ROM in your CD drive.
The <SETUP DISK STARTUP SCREEN> will
appear.
6
2. Click [Install Products].
3. Click [Error Recovery Guide] on the next
screen.
4. Select a language to use for the installation in
the <Choose Setup Language> window and
click [OK].
Image Processing Software Option
(Trial)
For details on the installation of the Image Processing
Software Option, refer to the "Image Processing Software Option USER’S GUIDE".
Adobe
®
Acrobat
Install Adobe Acrobat from the "Adobe Acrobat CDROM" provided with this scanner.
ATTENTION
Adobe Acrobat is not supported by
Microsoft Windows 95, Microsoft Windows 98/98SE, Microsoft Windows NT4.0,
Microsoft Windows Me.
®
5. Install the application following the instructions
in the window.
6. When the [InstallShield Wizard Complete]
screen displays, click [Finish].
fi-5015C Image Scanner Getting Started 7
HINT
Adobe Acrobat is required for displaying
the manuals stored in the CD-ROM.
* Installation of Adobe Acrobat is not necessary if it has already been installed in
your PC.
1. Insert the "Adobe Acrobat CD-ROM" into the
CD-ROM drive.
⇒ The "Adobe Acrobat" window appears.
ATTENTION
This window is not displayed automatically
when the "Auto play" setting of your computer is deactivated. In this case, please
run "Auto play.exe" of this CD-ROM
directly from "Explore" or "My computer".
2. Select the language and Click [OK] button.
3. Select "Install Adobe Acrobat".
ATTENTION
Notes for using Adobe Acrobat
When scanning a paper document and
converting the image to PDF using Acrobat unexpected images may be output
when:
1. Setting "Edge Shadow Removal" in Acrobat, and setting "Digital Endorser" or
"Black Background" options in the
TWAIN driver at the same time. Letter
strings embedded in the image or the
background may be missed.
Solution 1: Set "Edge shadow removal"
to "OFF" or set any option other than
"Adaptive" for "Color/Grayscale" and/or
"Monochrome" under "Compression" by
selecting [File]->[Create PDF]-> [From
Scanner...]-> [Image Settings...] in Acrobat.
Solution 2: Adjust the scanning density
in the TWAIN driver.
2. Setting "Adaptive" for "Color/Grayscale"
and/or "Monochrome" under "Compression" in Acrobat and scanning in a resolution lower than the resolution
recommended for Acrobat.
Solution: Set OPTION to something
other than "Adaptive" under "Compression."
*As for detailed usage and information of
Acrobat, refer to "Create a PDF file from a
scanned document" in Acrobat Help.
4. Click the [Next] button. The set up window
appears.
5. Follow the instructions to install the software.
HINT
Select "How to install" on the "Adobe Acrobat" window to learn more about Adobe
Acrobat installation. Refer to "Adobe Acrobat Help" about how to use Adobe Acrobat.
ATTENTION
■
Uninstalling Supplied Programs
Support and User registration for Adobe
products:
Refer to the technical support information
stored in the [Customer Support] folder on
Adobe Acrobat CD-ROM. (Note that free
person-to-person support is not available
for this bundled product.)
Follow the procedure below to uninstall supplied programs.
HINT
Windows XP screenshots are used in this
section. The windows and operations may
slightly vary depending on your OS.
1. Start up your PC.
ATTENTION
When using Windows NT 4.0, Windows
2000 or Windows XP, log on as a user with
"Administrator" privileges (privileges of the
administrator of your PC).
8
2. Exit all currently running programs.
2.2 Installing the Scanner
3. Select [Control Panel] - [Add or remove Programs] from the [Start] menu.
⇒ This displays the "Add or remove Programs"
screen which displays a list of the currently
installed applications.
4. Select the application to uninstall.
• When uninstalling FUJITSU TWAIN 32
scanner driver,
select "Scanner Utility for Microsoft Windows".
• When uninstalling Scandall 21,
select "ScandAll 21".
• When uninstalling FUJITSU ISIS scanner
driver,
select "Fujitsu ISIS Drivers".
• When uninstalling QuickScan Pro
select "QuickScan 3.0".
• When uninstalling Error Recovery Guide,
select "Error Recovery Guide".
• When uninstalling Image Processing Soft-
ware Option,
select "Image Processing Software Option"
• When uninstalling Software Operation
Panel,
select "Software Operation Panel".
ATTENTION
When uninstalling Adobe Acrobat, refer to
the installation procedure described in the
Adobe Acrobat CD-ROM.
5. Click the [Change/Remove] or [Remove] button.
TM
,
After the computer has been restarted, connect the scanner.
1. Place the scanner at its installation site.
For details on the scanner's dimensions and
required installation space, refer to "fi-5015C
Operator’s Guide" "Appendix A Installation
Specifications" in the Setup CD-ROM.
2. Unlock the shipping lock
The carrier unit inside the scanner is fixed in place
by the shipping lock to prevent the scanner from
becoming damaged during transportation from
factory.
After transporting and placing the scanner, release
the shipping lock.
3. Installation of the ADF paper chute, Extension
and Document stopper.
Attach Extension to ADF paper chuter, and then
mount it on the scanner; attach Document stopper
to the scanner.
ADF paper chute
Extension
Document stopper
6. When the confirmation dialogbox appears,
Click the [OK] or [Yes] button.
⇒ This executes the uninstallation.
ATTENTION
Screen displays may vary slightly according to the operation system (OS) you are
using. Follow the on screen instructions of
the OS.
Example: When the OS Windows 2000
• "Add or Remove Programs" - "Add/
Remove Applications"
• [Changel/Remove] button - [Add/
Remove] button.
fi-5015C Image Scanner Getting Started 9
4. Connect the ADF cable to the ADF cable connector on the scanner, and secure it with
screws.
Screw
5. Connect the AC adapter.
2.3 Connecting the Scanner to Your PC
Follow the procedure below to connect the USB cable.
1. Connect the USB interface cable to the USB
interface connector.
2. Connect the other end of the USB interface
cable to the PC.
ATTENTION
Use only the AC adapter provided by the
manufacturer.
1) Connect the AC cable to the AC adapter.
2) Connect the AC adapter connector to the
scanner’s DC inlet.
3) Plug the AC cable into the outlet.
ATTENTION
• Be sure to use the USB cable which
comes as an accessory with this scanner. Correct operation with commercially
available cables is not guaranteed.
• When connecting to an USB hub, use
the first stage USB hub that is closest to
the computer. If you use the second or
later hub stages, the scanner may not
operate correctly.
• If you connect the scanner with USB 2.0,
it is required that the USB port and Hub
are compliant with USB 2.0. The scanning speed may slow down if it is connected with USB1.1.
3. Press the "I" side of the main power switch to
turn on the scanner.
4. Press the power button to turn ON the scanner.
Your scanner will be automatically detected.
For Windows 98:
When a request for inserting the CD-ROM for
Windows 98 appears, insert it into the CD drive
and click the [OK] button.
For Windows 2000:
When [Digital Signature not Found] appears,
click [Yes].
The installation of the scanner is completed.
10
HINT
The Function Number Display and the LED
may flash for an instant when plugging the
AC cable into the outlet.
2.4 Confirming Installation
To confirm whether the installation was successful, perform a scanning operation with an application that complies with either the TWAIN regulations, such as
ScandAll 21 or the ISIS regulations such as QuickScan
ProTM.
■ Confirming with ScandAll 21
1. Load the documents on the scanner.
For details on loading documents, refer to "2.2
Loading Documents on the ADF for Scanning" in
the fi-5015C Operator's Guide on the Setup CDROM.
2. Start ScandAll 21.
Select [Start] - [Programs] - [Scanner Utility for
Microsoft Windows] - [ScandAll 21].
3. Specify the scanner (that you will use)
Select [Select Source...]from the [Scan] menu of
ScandAll 21.
4. Select "FUJITSU fi-5015C" on the dialog box.
HINT
7. Documents are scanned, and the scanned
images are displayed on the [ScandAll 21] window.
For details on [TWAIN driver], refer to the
"FUJITSU TWAIN32 Scanner Driver User’s
Guide" provided in the Setup CD-ROM.
5. Select [To View...] from the [Scan] menu.
6. Set scanning resolution, document size, etc. on
the [TWAIN driver] window (for setting details
of scanning) and click the [Scan] button.
If the scanning completes without any trouble, the instalation performed successfully.
For details on various types of scanning, refer to the
"fi-5015C Operator’s Guide" on the Setup CD-ROM.
■ Confirming with QuickScan Pro™
1. Load the documents on to the scanner.
For details on loading documents, refer to "2.2
Loading Documents on the ADF" in the fi-5015C
Operator's Guide on the Setup CD-ROM
2. Start QuickScan Pro™.
From the [Start] menu, select [Programs]-[QuickScan]-[QuickScan].
.
fi-5015C Image Scanner Getting Started 11
3. Select [Select Scanner...] from [Scan] menu in
QuickScan Pro™.
And, select fi-5015C from the list of [Scanner:],
and then click the [OK] button.
4. Select [Preview Settings...] from the [Scan]
menu. Set the scan resolution, paper size and
other scanning requirements, and then click
[OK].
HINT
Refer to "QuickScan Overview" or "QuickScan Help" for information about QuickScan Pro™ functions and operations. On
the [Start] menu, point to [Programs][QuickScan] and click the file.
5. Select [Preview Scan] from the [Scan] menu.
And then the document is scanned.
If the scanning completes without any trouble, the instalation performed successfully.
12
Appendix1 TROUBLESHOOTING
■ Troubleshooting checklist
Symptom Check this item Remedy
Scanner does not turn on. Is the main switch turned on? Turn the main switch on.
Have you pushed the power button? Push the power button.
Are the AC cable and AC adapter prop-
erly connected to the scanner?
Is Windows normally started up? Push the power button again after completely
Scanning does not start. Are the documents loaded correctly on
the ADF paper chute?
Is the ADF closed completely? Close the ADF completely.
Is the USB cable properly connected? Correctly connect the cable. (When a USB hub is
Does the Function Number Display indicates an alarm or an error?
Does the alarm state remain displayed
even after the scanner has been turned
off and back on again?
Vertical lines appear in the
generated image of the
scanned image.
The generated image shifts
or is distorted.
Quality of generated image
is unsatisfactory.
Multi feed frequently
occurs. (*)
Is the glass dirty? Clean the glass following the instructions in the
Are the documents loaded correctly? Load the documents correctly.
Are the glass or sheet guides (a white
location) clean?
Do the documents satisfy the "Document Quality" in the section 2.2.1 of the
fi-5015C Operator’s Guide?
Are the documents set properly in the
ADF paper chute?
Is the document stack thicker than 4mm? Reduce the number of sheets in the document
Is the Pad ASSY dirty? Clean the Pad ASSY. Refer to the Operator's
Is the Pad ASSY worn out? Replace the Pad ASSY. Refer to the Operator's
Correctly connect the AC cable and the AC
adapter.
Disconnect the AC cable and the AC adapter from
the scanner, then connect them again.
If this does not restore the power supply, contact
the store where you purchased the scanner or an
authorized FUJITSU scanner service provider.
starting up Windows.
Load the document correctly on ADF paper chute.
used, check the hub's power supply.)
When the Function Number Display indicates an
alarm or an error, refer to the "Chapter 4. TROUBLESHOOTING" in the fi-5015C Operator’s
Guide for removing the alarm or the error.
Turn off and on the power button.
If this does not eliminate the alarm state, contact
the store where you purchased the scanner or an
authorized FUJITSU scanner service provider.
Operator's Guide "3 Maintenance".
Clean dirty locations.
Scan the document by Flatbed.
Fan the documents before scanning. Correctly
align the document stack and load them on the
ADF paper chute. Refer to Section 2.2.2 of the fi5015C Operator’s Guide.
stack to 4 mm thickness or less.
Guide "3.2.3 Cleaning the ADF".
Guide "3.3.3 Replacing the Pad ASSY".
fi-5015C Image Scanner Getting Started AP-1
Symptom Check this item Remedy
Paper is not fed (pick error
occurs frequently, or document stops midway).
The generated images are
elongated.
There is a shadow on the
leading edge of the generated image?
Do the documents satisfy the "Document Quality"in Section 2.3.1of the fi5015C Operator’s Guide?
Is the thick document placed on the Flatbed?
Is the Pick roller unit dirty? Clean the Pick roller unit. Refer to the Operator's
Is the Pick roller unit worn out? Replace the Pick roller unit. Refer to the Opera-
Are the Pick roller unit dirty? Clean the Pick roller unit. Refer to the Operator's
Are the Pick roller unit dirty? Clean the Pick roller unit. Refer to the Operator's
Have you adjusted the offset (the scanning starting position)?
* "Multi feed" means that more than 2 papers are fed at the same time.
Scan the document by Flatbed.
Is the thick document placed on the Flatbed?
Guide "3.2.3 Cleaning the ADF".
tor's Guide "3.3.4 Replacing the Pick roller unit".
Guide "3.2.3 Cleaning the ADF".
Guide "3.2.3 Cleaning the ADF".
Adjust the [Sub-scan Setting] on [Scanners and
Cameras] in the control panel.
AP-2
■ Temporary error
■ Device alarm (Permanent error)
Indication Description
U0 Shipping lock error occurred.
U1 A paper feed error occurred.
U9 ADF error.
The following shows the procedure for releasing of each
temporary error.
• "U0" error
Confirm that the shipping lock is released.
Refer to "2.2 Installing the Scanner" (page 9)
• "U1" error
1. Remove jammed documents.
(Refer to fi-5015C Operator’s Guide "3.1 How
to clear the paper jam" on the Setup
CD-ROM
2. Confirm that the documents meet the paper
conditions for scanning.
(Refer to fi-5015C Operator’s Guide "2.2.1
Checking document condition" on the Setup
CD-ROM.)
• "U9" error
Turn off the scanner power. Confirm / Connect
the ADF cable, then turn on the scanner power.
* Be sure of switching off the main switch, in
case you make any operation with ADF cable.
Indication Description
E0 Flatbed motor malfunction.
E2 Trouble in the optical system.
E7 Trouble occurred in the internal memory
(EEPROM).
Eb An LSI error.
Ec An error in the memory.
Ed An error with USB
When you encounter any alarm, turn off and on the
scanner. If the alarm is still displayed on the Function
Number Display, contact the store where you purchased
the scanner or an authorized FUJITSU scanner service
provider.
.)
fi-5015C Image Scanner Getting Started AP-3
Appendix2 DAILY CARE
When operating the scanner, the
WARNING
ADF’s inside glass becomes very
hot.
Before you clean inside the scanner, turn off its power and unplug
the AC adapter from the outlet. Wait
for at least 15 minutes.
■ Cleaning Materials
Cleaning
Materials
Cleaner F1
(or isopropyl
alcohol)
Lint-free dry
cloth
For details about the cleaning materials, contact the
FUJITSU scanner dealer where you purchased the scanner.
Parts No. Remarks
CA995010013
- Commercially available one
1 bottle
Moisten a cloth with
this fluid and wipe the
scanner clean.
■ Locations and Cycle for Cleaning
Part to clean Standard Cleaning Cycle
Pad ASSY Clean these parts after every
1,000 scans.
Pick roller unit
Pinch roller
Glass
ATTENTION
For details on the cleaning the ADF, refer to "3.2 cleaning the ADF" in fi-5015C Operator’s Guide on the Setup
CD-ROM".
The scanner must be cleaned more frequently if you scan any of the following
type of sheets:
• Documents of coated paper
• Documents that are almost completely
covered with printed text or graphics
• Chemically treated documents such
as carbonless paper
• Documents containing a large amount
of calcium carbonate
• Documents written by pencil
• Documents with not enough fixed a
toner.
■ Cleaning Method
The ADF must be cleaned with a lint-free cloth moistened with the Cleaner F1.
AP-4
Appendix3 REPLACING CONSUMABLES
During its operation, the inside
WARNING
glass of the ADF becomes very
hot .
Before replacing the
consumables, turn its power off
and unplug the AC adapter from
the outlet. Wait at least
15 minutes.
■ Consumables and Replacement
Cycle
The followings are the specifications of consumables
and their recommended replacement cycles.
Description Parts No.
Standard
Replacement Cycle
The following illustrations show the locations of the
consumables. Refer to "Chapter 4 Replacing Consumables" fi-5015C Operator’s Guide on the Setup
CD-ROM.
■ Replacing the Pad ASSY
Pad ASSY
■ Replacing the Pick Roller unit
Pad ASSY PA03209-
0550
Pick roller unit PA03209-
0551
To purchase consumables,
purchased the scanner or an authorized FUJITSU scanner
service provider.
contact the store where you
After 20,000 scans or
one year
After 100,000 scans or
one year
The replacement cycles above are rough guidelines
when using the following type of paper:
Woodfree paper or Plain paper.
This cycle varies according to the type of the used paper
and how frequently the scanner is used and cleaned.
ATTENTION
Use only the specified consumables.
fi-5015C Image Scanner Getting Started AP-5
fi-5015C Image Scanner Getting Started
P3PC-1582-01EN
Date of issuance: February, 2006
Issuance responsibility: PFU LIMITED
z Copying of the contents of this manual in whole or in part and
copying of the scanner application is forbidden under the
copyright law.
z The contents of this manual are subject to change without notice.
z PFU LIMITED is not liable whatsoever for any damages resulting
from use of this scanner and procedures described in this manual,
profit loss due to defects, and any claims by a third party.
Loading...