Fujifilm X100 Service Manual

Confidential: FUJIFILM Service Center Use Only

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

FinePix X100

CAUTION

 BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIGNATED

AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN
PERFORMING REPAIRS. (Refer to page 3)

WARNING

THE COMPONENTS IDENTIFIED WITH THE MARK "



DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.

PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC



DIAGRAM AND IN THE PARTS LIST.

 IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN ELECTRICAL

SHOCK.

" ON THE SCHEMATIC

Ref. No.: ZM00925-106

Printed in Japan 2013.01

1

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

SAFETY CHECK-OUT

After correcting the original problem, perform the following

safety check before return the product to the customer.

1. Check the area of your repair for unsoldered
or poorly soldered connections. Check the
entire board surface for solder splasher and
bridges.

2. Check the interboard wiring to ensure that no
wires are "pinched" or contact high-wattage
resistors.

3. Look for unauthorized replacement parts,
particularly transistors, that were installed
during a previous repair. Point them out to the
customer and recommend their replacement.

4. Look for parts which, though functioning, show
obvious

signs of deterioration. Point them out to the

7. CAUTION: FOR
CONTINUED PROTECTION
AGAINST FIRE HAZARD,
REPLACE ONLY WITH
SAME TYPE 2.5 AMPERES
125V/250V FUSE.

ATTENTION: AFIN

RISK OF FIRE-

2.5A 125V/250V

REPLACE FUSE

2.5A 125V/250V

AS MARKED

D'ASSURER UNE
PROTECTION
PERMANENTE CONTRE
LES RISQUES D'INCENDIE,
REMPLACER
UNIQUEMENT PAR UN
FUSIBLE DE MEME, TYPE

2.5 AMPERES, 125/250
VOLTS.

customer and recommend their replacement.

5. Check the B + voltage to see it is at the values
specified.

6. Make leakage - current measurements to
determine that exposed parts are acceptably
insulated from the supply circuit before
returning the product to the customer.

8. WARNING:
TO REDUCE THE

ELECTRIC SHOCK, BE
CAREFUL TO TOUCH THE

WARNING!

HIGH VOLTAGE

PARTS.

2

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

RoHS lead-free compliance

With the exception of parts and materials expressly excluded from the RoHS directive, all the internal con nections and
component parts and materials used in this product are lead-free compliant under the European RoHS directive (*1). Use the
designated after-sales parts and the designated lead-free solder when performing repairs.

*1: Definition of lead-free
A lead content ratio of 0.1 wt% or less in the applicable locations (solder, terminals, electronic components, etc.)

<Lead-free soldering>

When lead-free solder is used, the solder tends to be less workable than when eutectic solder is used. When carrying out
repairs, use a designated lead-free solder, bearing in mind the differing work practices for eutectic solder and lead-free
solder.

■

Differences in the soldering work for lead-free and eutectic solder

Melting point 183°C 220°C

Soldering iron temperature 283°C 320°C

Wetting Good Poor
Surface Gloss Matte

Eutectic solder (Sn-Pb) Lead-free solder

■

Recommended equipment

(Sn-Ag-Cu)

Remark

The bonding temperature that will
give the best bond strength.

lead-free

Wire diameter

Solder type (Displayed symbol)
SnAgCu

■

Soldering iron maintenance

Because of the high soldering iron temperature in lead-free soldering, there is rapid carbonization of the flux adhering to

the tip of the soldering iron.
(1) Always cover the tip of the soldering iron with solder when it is not being used.
(2) If the tip is black from carbonization, wipe it gently with a paper towel soaked in alcohol until the solder will wet.

3

MEMO

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

4

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

1. Disassembly ............................................................................................................1-1

2. Schematics ..............................................................................................................2-1

3. Adjustments ............................................................................................................3-1

4. Inspection ................................................................................................................4-1

5. Parts List 1

6. Appendix...................................................................................................................6-1

(Packing and Accessories) (Mechanical Block) (Electrical parts)............. 5-1

CONTENTS

5

MEMO

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

6

Confidential: FUJIFILM Service Center Use Only



1. Disassembly

1-1. Removing the CASE

(1) Remove DECO PLA TE LEVER the direction of the arrow.
(2) Remove the 1 screws.（MS2M 1.4X2.0L）
(3) Remove SHEET LEVER FINDER the direction of the arrow.

1

FinePix X100 Service Manual

2

2

2

3

3

(4) Peel off the SHEET GRIP F RIGHT.
(5)Peel off the SHEET SC GRIP FRONT.

4

5

1-1



(6)Peel off the SHEET GRIP F LEF.
(7)Peel off the SHEET SC TOP F-L.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

7

(8)Peel off the SHEET GRIP R RIGHT.
(9)Peel off the SHEETSC GRIP RIGHT.

6

8

9

1-2



（10）Peel off the SHEET SC TOP F-R.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

10

（11）Peel off the SHEET GRIP R LEFT.
（12）Peel off the SHEET SC GRIP LEFT.

11

12

[Assembly]

Refer to the sheet sticking procedure.
Recycling prohibition of SHEET.

1-3



1-2. Removing the CASE BOTTOM

(1) Remove the 4 screws.（N-MSGM 1.7X2.5L）
(2) Remove the 2 screws.（N-MSGM 1.7×4.0）

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

(3) Remove the 2 screws.（N-NS2M 1.7×3.5）

1

2

3

1-4

(4) Remove the 2 screws.（N-MSGM 1.7×2.5）

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

4

(5) Remove the 1 screws.（N-MS2M 1.7×2.5）
(6) Remove the 2 screws.（N-MS2M 1.7×4.5）
(7)Remove the COVER DC COUPLER.
(8)Remove the CASE BOTTOM.

5

6

Revised:25.May.2011

1-5



1-3. Removing the CONST REAR

（1）Remove the 4 screws.（N-MS2M 1.7×2.5）

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

（2）Remove the 2 screws.（N-NS2M 1.7×3.5）
（3）Remove the 2 screws.（BT2M 1.7×5.0）

2

1

3

1-6

Confidential: FUJIFILM Service Center Use Only



（4）Remove the 1 screws.（N-MSNM 1.7×3.0B）

【メインコンデンサーのディスチャージ箇所】

ディスチャージ前にメインコンデンサー端子を触らないように注意してください。

4

FinePix X100 Service Manual

（5）Remove the 1 screws.（BT2M 1.7×4.0）
（6）Remove the 1 screws.（BT2M 1.7×6.0）

6

5

1-7



（7）Remove the 1 screws.（N-NS2M 1.7×3.5）

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

7

(8）Remove the flexible cable.

1-8



(9) Remove the BUTTON R LEFT.
(10) Remove the WINDOW LCD and CUSHION LCD.

9

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

10

(11) Remove the flexible cable.

11

1-9



1-4. Removing the LCD

(1) Peel off the CUSHION PWB REAR.
(2)

Remove the LCD_BL_FPC.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

(3) Unlock the connector and remove the LCD FPC.
(4) Remove Y6221RAER FPC ASSY the direction of the arrow.

3

1

2

4

1-10



1-5. Removing the CONST FRAME MAIN

(1) Peel off the UL TAPE.
(2)Unlock the connector and disconnect the flexible cable.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

(3)Remove the 1 screws.（MS2M 1.7×2.5）
(4)Remove CONST PWB SIDE in the direction of the arrow.

3

1

4



1-11



(5) Remove the SIDE FPC.
(6) Peel off the SHEET HEAT FRAME.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

6

5

(7) Remove the SPEAKER.

5

1-12



A

(8)Remove the 3 screws. (MSGM 1.7×2.5）
(9)Remove the 1 screws. (BT2M 1.7×4.0）

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

8

[Main capacitor discharge points]

Take care not to touch the main capacitor terminals before discharging the capacitor.

Discharge the main capacitor as shown in the figure.

8

9

1-13



1-6. Removing the CONST TOP

(1) Peel off the UL TEPE.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

(2)Unlock the connector and remove the MAIN TOP FPC.

2

1-14



(3) Unlock the connector and remove the SIDE FPC.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

3

(4) Peel off the SHEET HARNESS MC R.

4

1-15



(5)Remove the 1 screws.（N-MSGM 1.7×2.5）.
(6) Remove the 2 screws.（PS2AM 1.4×3.5）.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

5 6

(7) Remove the special 1 screws.（T-BTPM 1.0×4.0）

(Use Hexalobular (star screwdriver)T1 Type.)

(8) Remove the CONST TOP.

6

7

1-16



(9) Peel off the ULTAPE.
(10) Unlock the connector and remove the EVF FPC.

9

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

10

(11) Peel off the ULTAPE.
(12) Unlock the connector and remove the MAIN-TOP FPC.

11

12

1-17



1-7. Removing the LENS ASSY

(1) Remove EYE PIECE in the direction of the arrow.

1

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

(2) Remove the flexible cable.

2

1-18



(3) Remove the flexible cable.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

3

(4) Peel off the SHEET HARNESS MC F.
(5) Remove the 1 screws.（PS2AM 1.4×3.0）
(6) Remove the TRIPOD SCREW.

4

5

6

1-19



(7) Peel off the SHEET ES.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

7

(8) Remove the 1 screws.（PS2AM 1.4×3.5）
(9) Remove WINDOW EYE SENSOR in the direction of the arrow.

8

9

1-20



(10) Remove the EYE FPC PWB ASSY.

10

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

(11)

Peel off the UL TAPE.

11

1-21



(12) Peel off the UL TAPE.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

(13) Peel off the UL TAPE.



12

13

1-22

(14) Unlock the connector and remove the LENS FPC.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

14

(15) Unlock the connector and remove the MAIN-CAM FPC.
(16) Remove the LENS.

(17) Remove the 3 screws.（BT2M1.7×5.0）and Remove the LENS ASSY

15

17

Revised:25.May.2011

1-23



1-8. Removing the CONST FRONT

(1) Peel off the ULTAPE.

Confidential: FUJIFILM Service Center Use Only

FinePix X100 Service Manual

1

(2) Remove the flexible cable.

2

1-24