Fluke MPG2-H-HV, MPG2-H User Manual

MPG2-H™ and MPG2-H-HV™

Manual Pressure Generator/Controller

for Hydraulic Pressure

Operation and Maintenance Manual

High pressure liquids and gases are potentially hazardous. Energy stored in these liquids and gases can be released unexpectedly and with extreme force. High pressure systems should be assembled and operated only by personnel who have been instructed in proper safety practices.

Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of DH Instruments, a Fluke Company, 4765 East Beautiful Lane Phoenix AZ 85044-5318 USA.

DH Instruments makes sincere efforts to ensure the accuracy and quality of its’ published materials; however, no warranty, expressed or implied, is provided. DH Instruments disclaims any responsibility or liability for any direct or indirect damages resulting from the use of the information in this manual or products described in it. Mention of any product or brand does not constitute an endorsement by DH Instruments of that product or brand. This manual was originally composed in English and was subsequently translated into other languages. The fidelity of the translation cannot be guaranteed. In case of conflict between the English version and other language versions, the English version predominates.

DH Instruments, DH, DHI, E-DWT, GPC1, MPG2, MPG2-H, MPG2-H-HV, OPG1, PG7000, RPM4 are trademarks, registered and otherwise, of DH Instruments, a Fluke Company.

Document No. 3340765 080515 Printed in the USA

AABBLLEE OOFF

TABLE OF CONTENTS ...............................................................I

TABLES..................................................................................II

FIGURES.................................................................................II

ABOUT THIS MANUAL.............................................................III

1. INTRODUCTION ................................................................. 1

1.1 PRODUCT OVERVIEW ...........................................................................................................................1

1.2 SPECIFICATIONS ...................................................................................................................................1

1.3 LOCATION OF THE COMPONENTS......................................................................................................2

1.4 DIMENSIONAL SCHEMATICS................................................................................................................4

1.5 HYDRAULIC SCHEMATIC......................................................................................................................5

2. INSTALLATION .................................................................. 7

2.1 UNPACKING AND INSPECTION ............................................................................................................7

2.2 SITE REQUIREMENTS............................................................................................................................7

2.3 INITIAL SETUP........................................................................................................................................8

OONNTTEENNTTS

3. OPERATION....................................................................... 9

3.1 GENERAL OPERATING PRINCIPLES AND INFORMATION.................................................................9

3.1.1 OVERVIEW....................................................................................................................................................9

3.1.2 VALVES.........................................................................................................................................................9

3.1.3 PRIMING PUMP.............................................................................................................................................9

3.1.4 VARIABLE VOLUME (VV).............................................................................................................................9

3.1.5 RESERVOIR ................................................................................................................................................10

3.2 OPERATION..........................................................................................................................................10

3.2.1 FILLING AND PRIMING THE SYSTEM UNDER TEST, PRIMING PUMP..................................................10

3.2.2 GENERATING AND ADJUSTING PRESSURE, VARIABLE VOLUME AND FINE ADJUST VALVE........11

3.2.3 REFILLING OR EMPTYING THE VARIABLE VOLUME WITHOUT RELEASING TEST PRESSURE......12

4. MAINTENANCE AND ADJUSTMENTS .................................. 13

4.1 REPLACING LIQUID AND FLUSHING HYDRAULIC SYSTEM............................................................13

5. WARRANTY STATEMENT .................................................. 15

MPG2-H OPERATION AND MAINTENANCE MANUAL

AABBLLEES

Table 1. MPG2-H and MPG2-H-HV Parts List.............................................................................................7

Table 2. DHI Authorized Service Providers ...............................................................................................16

IIGGUURREES

Figure 1. Front view .....................................................................................................................................2

Figure 2. Rear view......................................................................................................................................2

Figure 3. Top view........................................................................................................................................3

Figure 4. Front view dimensions..................................................................................................................4

Figure 5. Bottom and side view dimensions................................................................................................4

Figure 6. System schematic.........................................................................................................................5

ABOUT THIS MANUAL

BBOOUUTT

This manual provides the user with the information necessary to operate an MPG2-H Manual Pressure Generator/Controller for Hydraulic pressure. It also includes additional information provided to help you optimize MPG2 use and take full advantage of its many features and functions.

For those of you who “don’t read manuals”, go directly to Section 2.3 to set up your MPG2. Then go to Section 3.2. This will get you running quickly with minimal risk of causing damage to yourself or your MPG2. Then… when you have questions or start to wonder about all the great features you might be missing, get into the manual!

(CAUTION) is used throughout the manual to identify user warnings and cautions.

(NOTE) is used throughout the manual to identify operating and applications advice and additional explanations.

HHIISS

AANNUUAAL

Manual Conventions

MPG2-H OPERATION AND MAINTENANCE MANUAL

OOTTEES

1. INTRODUCTION

11.

NNTTRROODDUUCCTTIIOON

1.1 PRODUCT OVERVIEW

The DHI Manual Pressure Generator/Controller for Hydraulic Pressure (MPG2-H) provides a compact and easy to use system for manually generating, setting and finely adjusting pressures between atmosphere and 200 MPa (30 000 psi) in closed volumes. MPG2 is a standard pressure generation and control component for working with DHI PG7302 piston gauges or liquid operated RPM4 reference pressure monitors. MGP2 and RPM4 are available as a single, integrated pressure calibration instrument designated E-DWT

The MPG2-H-HV has a larger displacement variable volume (7 cc rather than 3 cc) and is intended for applications with higher test volumes to reduce variable volume stroke needed to generate the desired pressure. The maximum working pressure of MPG2-H-HV is 100 MPa (15 000 psi). The MPG2-H requires less variable volume torque and adjusts pressure more precisely.

1.2 SPECIFICATIONS

MPG2-H MPG2-H-HV

Pressure range

Variable volume piston

Variable volume stroke

Priming pump displacement

Reservoir capacity

TEST1, TEST2 connections

Due to a policy of continuous product improvement all specifications are subject to change without notice.

diameter

Variable volume

displacement

Operating fluid

Dimensions

Weight:

Atmosphere to 200 MPa (30 000 psi) Atmosphere to 100 MPa

7.9 mm 12 mm

6 cm 6 cm 7 cc (.43 in.3) 3 cc (0.18 in. 3)

3.7 cc (0.23 in. 300 cc (18 in. DH 500 (DH500 is a gland and collar type fitting for ¼ in. (6 mm) coned and

left hand threaded tube. DH500 is equivalent to AE F250C, HIP HF4, etc.) Any non-corrosive oil, water, water/alcohol. Inquire about other fluids 400 mm W x 136 mm H x 300 mm D (15.8 in. x 5.4 in. x 11.8 in.)

(see Section 1.4 ) 10 kg (22 lbs.)

)

(15 000 psi)

+ 15 hidden pages