Installation, Operation, Maintenance Instructions
Low Flow Valves
030 000 Globe Valves
Flow Control Division
Kammer Control Valves
Index
1 Using Kämmer valves and actuators correctly.
2 Unpacking
3 Installation
4 Quick check
5 Maintenance
6 Remove and install actuator
7 Disassemble and assemble valve
8Trouble-shooting chart
1 USING KÄMMER VALVES AND ACTUATORS
CORRECTLY
1.1 General
The following instructions are designed to assist in
unpacking, installing and performing maintenance as
required on Kämmer products. Product users and
maintenance personnel should thoroughly review this
bulletin prior to installing, operating or performing
any maintenance.
DANGER:
are designed for specific applications (e.g. with regard
to medium, pressure, temperature). For this reason
they should not be used in other applications without
first contacting the manufacturer.
1.2 Terms concerning safety
The safety terms DANGER, WARNING, CAUTION and
NOTE are used in these instructions to highlight
particular dangers and/or to provide additional
information on aspects that may not be readily
apparent.
DANGER:
and/or substantial property damage will occur if
proper precautions are not taken.
STOP!
WARNING:
and/or substantial property damage can occur if
proper precautions are not taken.
CAUTION: i
or property damage can occur if proper precautions
are not taken.
In most cases Kämmer valves and actuators
indicates that death, severe personal injury
indicates that death, severe personal injury
ndicates that minor personal injury and/
NOTE:
information, which may not be very obvious even to
qualified personnel. Compliance with other, not
particularly emphasised notes, with regard to
transport, assembly, operation and maintenance and
with regard to technical documentation (e.g. in the
operating instruction, product documentation or on
the product itself) is essential, in order to avoid faults,
which in themselves might directly or indirectly cause
severe personal injury or property damage.
1.3 Protective clothing
Kämmer products are often used in problematic
applications (e.g. extremely high pressures, dangerous, toxic or corrosive mediums). In particular
valves with bellows seals point to such applications.
When performing service, inspection or repair
operations always ensure, that the valve and actuator
are depressurised and that the valve has been cleaned
and is free from harmful substances. In such cases
pay particular attention to personal protection
(protective clothing, gloves, glasses etc.).
1.4 Qualified personnel
Qualified personnel are people who, on account of
their training, experience and instruction and their
knowledge of relevant standards, specifications,
accident prevention regulations and operating
conditions, have been authorised by those responsible
for the safety of the plant to perform the necessary
work and who can recognise and avoid possible
dangers.
1.5 Installation
DANGER:
serial-no. and/or the tag-no. to ensure that the valve/
actuator is correct for the intended application.
Do not insulate extensions that are provided for hot
or cold services.
Pipelines must be correctly aligned to ensure that the
valve is not fitted under tension.
indicates and provides additional technical
Before installation check the order-no,
KMEIM3001-00 - 09.03
1
Flow Control Division
Kammer Control Valves
1.6 Spare parts
Use only Kämmer original spare parts. Kämmer
cannot accept responsibility for any damages that
occur from using spare parts or fastening materials
from other manufactures. If Kämmer products
(especially sealing materials) have been on store for
longer periods check these for corrosion or deterioration before using these products. Fire protection for
Kämmer products must be provided by the end user.
1.7 Service / repair
To avoid possible injury to personnel or damage to
products, safety terms must be strictly adhered to.
Modifying this product, substituting nonfactory parts,
or using maintenance procedures other than outlined
in this instruction could drastically affect performance
and be hazardous to personnel and equipment, and
may void existing warranties. Between actuator and
valve there are moving parts. To avoid injury
Flowserve provides pinch-point-protection in the form
of cover plates, especially where side-mounted
positioners are fitted. If these plates are removed for
inspection, service or repair special attention is
required. After completing work the cover plates must
be refitted.
Apart from the operating instructions and the
obligatory accident prevention directives valid in the
country of use, all recognised regulations for safety
and good engineering practices must be followed.
WARNING:
STOP!
for repair or service Kämmer must be provided with
Before products are returned to Kämmer
a certificate which confirms that the product has been
decontaminated and is clean. Kämmer will not accept
deliveries if a certificate has not been provided (a form
can be obtained from Kämmer).
1.8 Storage
In most cases Kämmer Products are manufactured
from stainless steel. Products not manufactured from
stainless steel are provided with an epoxy resin
coating. This means that Kämmer products are well
protected from corrosion. Nevertheless Kämmer
products must be stored adequately in a clean, dry
environment. Plastic caps are fitted to protect the
flange faces to prevent the ingress of foreign
materials. These caps should not be removed until
the valve is actually mounted into the system.
1.9 Valve and actuator variations
These instructions cannot claim to cover all details
of all possible product variations, nor in particular
can they provide information for every possible
example of installation, operation or maintenance.
This means that the instructions normally include only
the directions to be followed by qualified personal
where the product is being used for is defined
purpose. If there are any uncertainties in this respect
particularly in the event of missing product-related
information, clarification must be obtained via the
appropriate FLOWSERVE sales office.
2 UNPACKING
2.1 Each delivery includes a packing slip. When unpacking, check all delivered valves and accessories using
this packing slip.
2.2 Larger valves can be lifted using slings on the yoke
rods or, if present, on the lugs provided for this purpose. If slings are used, attach them so that the outer
tubing or attaching parts are not damaged.
WARNING:
of gravity of the valve may be above the lifting point.
STOP!
If slings are used, be aware that the centre
In this case, secure or support the valve against rotating, to prevent damage or personnel injury.
2.3 Report transport damage to the carrier immediately.
2.4 In case of discrepancies, contact your nearest
FLOWSERVE sales office.
3 INSTALLATION
3.1 Clean tubing prior to installing.
3.2 If possible, install the valve in an upright position (actuator on top), to ease maintenance. An upright installation position is important with low-temperature
applications, in order to keep the distance between
the packing material and the medium as large as possible. The packing material then retains the ambient
temperature as much as possible.
NOTE:
Do not insulate extension bonnets that are pro-
vided for hot or cold services
3.3 Make sure that sufficient overhead clearance above
the actuator is maintained, to allow for disassembly
of plug from the valve body (see following table).
Actuator Clearance Actuator Clearance
size (mm) size (mm)
37/47 95 P2 140
38/48 140 P3 140
39/49 140 P4 140
39D/49D 140 P5 140
3.4 After installing, check direction of flow again. The direction of flow is shown by the arrow on the housing.
3.5 If the valve is to be welded into the line, make sure
that the valve is shielded from excessive heat.
3.6 Connect supply pressure and signal lines. Control
valves are supplied with a positioner. The end connections for supply pressure and signal are clearly
marked. Actuator and positioner are suitable for max.
4.2 bar (60 psi) supply pressure. If the supply pres-
2
Flow Control Division
Kammer Control Valves
sure exceeds the pressure specified on the nameplate,
a pressure reducing station is required. If instrument
air is not available, install an oil separator/air filter in
the air inlet line. All connections must be leak free.
4 QUICK CHECK:
Before operating, check the valve as follows:
4.1 Open and close the valve, and observe the movement
of the actuator stem. The movement must be smooth
and linear.
4.2 Check for maximum stroke through change of signal
(for pneumatic positioners, 0.2 - 1.0 bar or corresponding split-range values; for IP positioners, 4-20
or 0-20 mA).
4.3 Check all air connections for leaks.
4.4 Tighten packing nut (see table 1).
Torque
Thread PTFE Grafoil
M20 x 1,5 1 3
M30 x 1,5 6 15
M38 x 1,5 15 35
M45 x 1,5 17 40
Table 1
NOTE:
An excessively tightened gland nut can cause
excessive packing wear and can hinder the free movement of the plug stem.
5.2 Check bellows gasket and test connection - if present - for
external leaks.
5.3 Check valve for damage caused by corrosive residues
or corrosive vapours.
5.4 Clean valves and repaint as necessary.
Warning:
STOP!
clean the actuator/valve with a damp cloth only.
To prevent a buildup of electrostatic charge
5.5 Check gland nut for correct torque (see table 1)..
NOTE:
An excessively tightened gland nut can cause
excessive packing wear and can hinder the free movement of the plug stem.
5.6 If possible, open and close valve and check for maximum stroke and smooth movement of the plug stem.
Irregular movement of the plug stem may indicate
internal defects.
NOTE: With graphite packing, irregular movement of
the plug stem is normal.
WARNING:
STOP!
all moving parts. Failure to do so can lead to serious
Keep hands, hair, clothing, etc. away from
injury.
5.7 Check all accessories for firm seating.
5.8 If possible, close supply pressure and check the failsafe position.
5.10 Check stem boot for wear.
4.5 Check fail-safe position. To do this, close supply pressure and observe whether the valve opens or closes
as defined.
4.6 After use at fluctuating temperatures, re-tighten all
bolt connections and check for leaks.
5 MAINTENANCE
Check valves for correct functioning at regular
intervals (at least once every 6 months) as follows.
This check can be made when installed and in many
cases without interrupting production. If internal
defects are suspected, see section „Disassembly and
Assembly of Valve“.
5.1 Examine gaskets for leaks and if necessary re-tighten
bolts (see Fig. 1).
5.11 Check actuator for leaks. To do this, spray housing,
air connections and plug stem guide with leak spray
and check for any bubble formation.
5.12 Clean plug stem.
5.13 Check air filter, if present, and if necessary replace
insert.
Note:
For further information regarding service and
maintenance please contact your nearest
FLOWSERVE office.
DANGER:
On actuators with aluminium cases the
actuator springs must be renewed with original spare
parts every 10 years or after 50.000 operating hours
which ever occurs first.
3
Flow Control Division
Kammer Control Valves
Cap
Travel indicator
Yoke plate
Yoke nuts
Zero adjustment locknut
Actuator stem
Locknuts
Gland nut
Clamping nut
Plug stem
Actuator series 4
Fig. 1
Coupling
Coupling screws
Coupling insert
Locknut
Yoke plate
Yoke nuts
Actuator series 2
Fig. 1a
4
REMOVE AND INSTALL ACTUATOR
Flow Control Division
Kammer Control Valves
General Information
We recommend separating the actuator from the
valve during all repair work. However, many
maintenance and adjusting operations can be
carried out in an installed condition.
6.1 Remove series 4 actuator
(see Fig 1 + 2)
For series 2 actuator see 6.3
For actuators with spring-to-close, go to 6.1.1
For actuators with spring-to-open, go to 6.1.2
6.1.1 Shut off air supply.
STOP!
WARNING:
pressure and drain all fluids from the valve before
working on the actuator. Failure to do so can cause
Depressurise the line to atmospheric
serious injury.
6.1.2 Remove cap and nameplate. Tighten zero adjusting
nut until it just touches the surface of the spring
housing. This relieves the plug from actuator spring
pressure. If the actuator is fitted with a handwheel
this can be used to relieve the plug from actuator
spring pressure.
6.1.3 Using a wrench, secure the actuator stem against
turning and using a second wrench loosen the stem
locknuts. If the actuator is fitted with a coupling refer to the procedure described in the maintenance
instructions for the I/P actuator.
CAUTION:
The actuator stem must not be rotated,
as this will cause damage to the diaphragm.
6.1.4 Loosen gland and clamp nuts.
6.1.5 Secure plug stem against turning and unscrew actuator from plug stem by rotating counter-clockwise.
CAUTION:
Ensure that the plug assembly is not rotated with the plug seated. This may cause irreparable damage to the seating faces.
6.1.5 Remove actuator and remove at the same time locknut, travel indicator disc, gland nut and clamp nut.
3.2 Install series 3 actuator
Information:
• Before the actuator is installed, it must be calibrated according to section 3 of the instructions
„Pneumatic and Electro-pneumatic Actuators“.
• All worn or damaged parts must be replaced.
Reusable parts must be clean.
6.2.1 Position actuator with clamp nut, gland nut, locknuts and travel indicator disc on the valve.
6.2.2 Only for „spring-to-close“ actuators:
Screw actuator onto plug stem by rotating clockwise, until the yoke plate just touches the valve housing and the actuator is aligned forward. If the actuator is fitted with a coupling refer to the procedure described in the maintenance instructions for
the I/P actuator.
CAUTION:
Ensure that the plug assembly is not rotated with the plug seated. This may cause irreparable damage to the seating faces.
Only for „spring-to-open“ actuators:
Lift plug stem and screw it into the lower coupling
half until the distance between „plug in seat“ and
„plug raised“ approximately corresponds to the specified stroke.
6.2.3 Tighten clamp nut and gland nut.
6.2.4 Adjust seat tightness by screwing/unscrewing the
plug stem in/out of the actuator stem.
CAUTION:
Ensure that the plug assembly is not rotated with the plug seated. This may cause irreparable damage to the seating faces. Open valve, make
adjustment, close valve and check for leaks. If the
valve is fitted with a bellows seal the plug stem may
NOT be rotated at all. In the case of a bellows seal
adjustments are made with the coupling.
6.2.5 After adjusting, secure the locknuts and the travel
indicator disc lying between them against actuator
stem and align the travel indicator on the yoke rod.
6.3 Remove series 2 actuator
(see Fig. 1a)
For series 4 actuator see 6.1
6.3.1 Shut off air supply.
WARNING:
pressure and drain all fluids from the valve before
STOP!
Depressurise the line to atmospheric
working on the actuator. Failure to do so can cause
serious injury.
6.3.2 Disconnect all tubing.
6.3.3 Remove 2 screws and remove coupling.
6.3.4 Remove yoke rod retaining nuts and lift actuator
assembly from the valve.
6.3.5 Remove coupling insert and it’s locknut from plug
stem.
NOTE:
Ensure that the plug assembly is not rotated
with the plug seated. This may cause irreparable
damage to the seating faces.
6.4 Install series 2 actuator
(see Fig. 1a)
The actuator stem must be fully extended:
Actuators with air-to-open action must be fully
vented. Actuators with air-to-close action apply
supply pressure.
Manually depress the plug stem to ensure the plug is
fully seated.
6.4.1 Screw coupling insert locknut and coupling insert as
far as possible onto plug stem.
6.4.2 Place the actuator assembly on the valve engaging
the yoke rod threads in the lower yoke plate and
ensuring the actuator faces in the correct direction.
5
Locknut
Flow Control Division
Kammer Control Valves
Packing follower
Packing
Guide bushing
Body
Gland nut
Clamp nut
Bonnet nut
Bonnet
Bonnet gasket
Plug stem
Seat ring
Seat ring gasket
Typical valve configuration
Fig. 1
6
4
Flow Control Division
Kammer Control Valves
7 DISASSEMBLE AND ASSEMBLE VALVE
General Information
We recommend separating the actuator from the
valve before commencing repair work.
However, many maintenance and adjusting operations can be carried out with the valve installed.
NOTE:
Never rotate the plug or perform any service
on the valve while the plug is seated in the seat ring.
Doing so may cause irreparable damage to the trim
set. To ensure against this, always hold the plug out
of the seat while working on the valve assembly.
7.1 Disassemble valve
7.1.1 Disconnect actuator from valve body
7.1.2 Hold the plug out of the seat. Using a 41 mm wrench
loosen and unscrew the bonnet nut and remove the
bonnet from the valve.
7.1.3 Carefully extract the plug from the bonnet. Note that
the threaded section of the plug stem is slightly
smaller in diameter than the guided section, this helps
prevent damage to the packing when removing the
plug from the bonnet.
7.2.5 Replace packing by inserting packing rings one at a
time tapping each one down with a suitable bushing.
NOTE:
ensure that the gaps in the packing rings are
distributed evenly around the circumferance in the
packing box (gaps not in line).
Different packings and fitting sequence is shown in
the spare parts list.
7.2.6 Insert packing follower. Fit gland nut for transport
purposes only. Gland nut to be fitted correctly and
tightened down when the actuator is mounted.
7.1.4 Remove the packing follower, packing rings and guide
bushing and clean the packing chamber.
7.1.5 Remove the bonnet gasket.
7.1.6 Remove seat and seat gasket.
7.1.7 Clean and inspect all parts.
7.2 Assemble valve
Attention: All worn or damaged parts must be re-
placed. Reusable parts must be clean. All consumable items such as seals, and gaskets must always
be renewed.
7.2.1 Replace seat gasket and seat ring.
7.2.2 Replace bonnet gasket.
7.2.3 Insert the plug into the bonnet. Install the guide bushing into the packing chamber with bevelled end facing down and insert the bonnet in the valve body.
7.2.4 Coat the bonnet nut threads with a small amount of
lubricant. Hold the plug stem fully retracted in the
bonnet and thread the bonnet nut onto the body. Using a 41 mm torque wrench torque the bonnet nut to
150 Nm.
7
Flow Control Division
Kammer Control Valves
Regional Headquarters
Flowserve Flowserve Flowserve
Manderscheidtstr. 19 1350 N. Mt. Springs Prkwy. 12 Tuas Avenue 20
45141 Essen Springville, UT 84663
Germany USA Singapore 638824
Telephone: +49 (0) 201 8919 5 Telephone: +1 801 489 8611 Telephone: +65 862 3332
Facsimile: +49 (0) 201 8919 662 Facsimile: +1 801 489 3719 Facsimile: +65 862 4940
Main Sales Offices (Europa, Middle east, Africa)
Flowserve Flowserve Flowserve Flowserve
von-Braun-Straße 19a 12, av. du Québec Station Road Allee du Quartz 1
48681 Ahaus 91965, Courtaboeuf Cedex Pershore, Worcestershire CH-2300 La-Chaux-de Fonds
Germany France England WR102BZ Switzerland
Telephone: +49 (0) 2561 6860 Telephone: +33 (0) 1 60 923 251 Telephone: +44 (0) 1386 55 45 51 Telephone: +41 (0) 32 925 9700
Facsimile: +49 (0) 2561 68648 Facsimile: +33 (0) 1 60 923 299 Facsimile: +44 (0) 1386 55 49 68 Facsimile: +41 (0) 32 926 5422
Flowserve Flowserve
Cnr. Bismit and Granier Str. C/O Saleh & Abdulaziz Abahsain
Jet Park Ext 3 P.O. Box 209
Boksburg
1459 Gauteng Al Khobar 31952
South Africa Saudi Arabia
Telephone: +27 397-3150 Telephone: 9663 857 3442
Facsimile: +27 397-5300/01/02 Facsimile: 9663 859 5284
8
©01.2001 Flowserve Corporation. Flowserve and Kämmer are trademarks of Flowserve Corporation
All data subject to change without notice
Loading...