Fisher & Paykel DD60SCHW7, DD60SCB7, DD60SCHB7, DD60SCM7, DD60SDFX7 Installation Instructions Manual

NZ AU GB IE

590200D 04.13

DD60S 7 & DD60ST 7 models

INSTALLATION INSTRUCTIONS

DishDrawer

TM

dishwasher

2

FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL

1

DD60SHI7
DD60SLI7

(not available in GBIE, only NZAU)

Classic

PRODUCT & CABINETRY

DIMENSIONS

(STANDARD HEIGHT)

PRODUCT & CABINETRY

DIMENSIONS

(STANDARD HEIGHT)

PRODUCT & CABINETRY

DIMENSIONS

(STANDARD HEIGHT)

PRODUCT & CABINETRY

DIMENSIONS

(TALL HEIGHT)

PRODUCT & CABINETRY

DIMENSIONS

(TALL HEIGHT)

PRODUCT & CABINETRY

DIMENSIONS

(TALL HEIGHT)

DD60SC(H)X7
DD60SC(H)W7

DD60SDF(H)X7
DD60SDFM7

DD60SC(H)B7
DD60SCM7

Designer

DD60SI7

DD60SC(H)TX7
DD60SC(H)TW7

DD60SDF(H)TX7
DD60SDFTM7

DD60SC(H)TM7

Integrated with remote control Integrated with badge control Integrated with remote control Integrated with badge control

Classic

Designer

DD60STI7 DD60SHTI7

CUSTOM FRONT

PANEL CALCULATIONS

CUSTOM FRONT

PANEL CALCULATIONS

PARTS SUPPLIED

CAVITY PREPARATION

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

CHOOSE

DRAINAGE OPTION

FINAL CHECKLIST

CONNECT TO WATER & ELECTRICITY

TROUBLESHOOTING

FINAL CHECKLIST

CONNECT TO WATER & ELECTRICITY

PARTS SUPPLIED

CAVITY PREPARATION

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

PARTS SUPPLIED +

EXTERNAL VENTING KIT

PARTS SUPPLIED +

EXTERNAL VENTING KIT

CAVITY PREPARATION

ATTA CH

CAVITY BRACKET

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

CHOOSE

DRAINAGE OPTION

FINAL CHECKLIST

TROUBLESHOOTING

FINAL CHECKLIST

TROUBLESHOOTING

SECURE WITHOUT
DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

PARTS SUPPLIED

CAVITY PREPARATION

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

CHOOSE

DRAINAGE OPTION

FINAL CHECKLIST

CONNECT TO WATER & ELECTRICITY

CHOOSE

DRAINAGE OPTION

TROUBLESHOOTING

PARTS SUPPLIED

CAVITY PREPARATION &

EXTERNAL VENTING

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

FOLLOW STEPS

FOR THE

EXTERNAL

VENTING KIT

INSTALL THE FRONT PANEL

INSTALL THE FRONT PANEL

CONNECT TO WATER & ELECTRICITY

CONNECT TO WATER & ELECTRICITY

CHOOSE

DRAINAGE OPTION

CONNECT TO WATER & ELECTRICITY

CHOOSE

DRAINAGE OPTION

CONNECT TO WATER & ELECTRICITY

CHOOSE

DRAINAGE OPTION

TROUBLESHOOTING

FINAL CHECKLIST

TROUBLESHOOTING

FOLLOW STEPS

FOR THE

EXTERNAL

VENTING KIT

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

480 mm CAVITY

ONLY - ATTACH

CAVITY BRACKET

FINAL CHECKLIST

CHOOSE

DRAINAGE OPTION

CONNECT TO WATER & ELECTRICITY

TROUBLESHOOTING

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

FOLLOW STEPS

FOR THE

EXTERNAL

VENTING KIT

FOLLOW STEPS

FOR THE

EXTERNAL

VENTING KIT

CAVITY PREPARATION &

EXTERNAL VENTING

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

456mm CAVITY

480mm CAVITY

PRODUCT & CABINETRY

DIMENSIONS

(TALL HEIGHT)

CUSTOM FRONT

PANEL CALCULATIONS

PARTS SUPPLIED

480 mm CAVITY

ONLY - ATTACH

CAVITY BRACKET

FINAL CHECKLIST

TROUBLESHOOTING

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

CAVITY PREPARATION

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

456mm CAVITY 480mm CAVITY

PRODUCT & CABINETRY

DIMENSIONS

(STANDARD HEIGHT)

CUSTOM FRONT

PANEL CALCULATIONS

PARTS SUPPLIED

CAVITY PREPARATION

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

INSTALL THE FRONT PANEL

& BADGE CONTROLS

INSTALL THE FRONT PANEL

& BADGE CONTROLS

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

STANDARD HEIGHT SINGLE MODELS

TALL HEIGHT SINGLE MODELS

ONLY AVAILABLE IN NZ AU ONLY AVAILABLE IN NZ AUONLY AVAILABLE IN GB IE ONLY AVAILABLE IN GB IE

3

SAFETY AND WARNINGS - ALL MODELS

ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY

2a

2b

WARNING!

Electrical shock hazard

Before installing the dishwasher, remove the house fuse or open the circuit

breaker.

This appliance must be earthed. In the event of a malfunction or breakdown,
earthing will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having an
equipment-earthing conductor and an earthing plug. The plug must be plugged
into an appropriate outlet that is installed and earthed in accordance with all
local codes and ordinances. WARNING- Improper connection of the equipment­earthing conductor can result in a risk of electric shock. Check with a qualified
electrician or service representative if you are in doubt as to whether the
appliance is properly earthed.

Do not modify the power supply plug provided with the appliance - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician. Do not use
an extension cord, adapter plug or multiple outlet box.

Failure to follow this advice may result in electrical shock or death.

WARNING!

Cut hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

IMPORTANT SAFETY INSTRUCTIONS!

Installation of this dishwasher requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building and electricity regulations.
At the completion of the dishwasher installation, the Installer must perform the Final Checklist.
Remove all packaging materials supplied with the dishwasher.
This dishwasher is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibility of the plumber and
electrician to ensure that each installation complies with all Codes and Regulations.
The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

The switched power outlet must be outside the dishwasher cavity, so that it is accessible after

installation.

Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to
the power supply cord and hoses.
If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.

Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should

not be reused.
Failure to install the dishwasher correctly could invalidate any warranty or liability claims.

If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle,

boat or mobile facility containing the product to the service shop at your expense or pay the service
technician’s travel to the location of the product.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS!

Read these instructions completely and carefully.
Ensure the product is not plugged in.
Installation of custom panels requires basic mechanical and electrical skills.
Installation must comply with your local building and electricity regulations.
Failure to install the custom panels correctly could invalidate any warranty or liability claims.

SAVE THESE INSTRUCTIONS

Electrical Shock Hazard

WARNING: To reduce the risk of electrical shock, fire, or injury to persons, the
installer must ensure that the dishwasher is completely enclosed at the time of
installation.
Before fitting the front panels and connecting the integrated badges (where
present), the installer must ensure that the dishwasher is disconnected from the
power supply.
After installing the front panel, the installer must ensure that the following
components are electrically earthed: the panel bracket, the integrated badge
(where present) and any custom metal component (e.g. handle) that extends
past the rubber seal.

Failure to follow these warnings may result in electrical shock, injury or fire.

WARNING!

Fitting integrated front panels requires access to electrical service areas.
This work must be performed and certified by a qualified electrical service technician.

4

PARTS SUPPLIED - ALL MODELS

3a

If the Drain hose supplied is not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose by 3.6m.
The kit is available from the nearest Fisher & Paykel Authorised Service Centre or through our local website listed at the end of this document.

Clamp (1)
(for securing

Drain hose joiner)

Wire clip (1)
(for securing

Drain hose joiner)

Phillips
16 mm
screws (7)

38 mm
bottom
fixing screws
& metal
washers (2)

Drain hose
support (1)

Moisture
protection
tape (1)

(to prevent
moisture damage)

Cavity bracket kit (1)

supplied with Tall height
Designer and Integrated
models only

Drain hose
joiner (1)

Rubber
washer for
inlet hose (1)

(comes already

fitted)

Side mounting
bracket kit
(A and B) (2)

OPTIONAL

5

ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS

3b

External Venting kit (1)

supplied with Integrated
models with remote only

Panel mounting
screws (6)

Panel bracket (1)

(attached to
product)

Integrated rectangular badge (1)

(Satin chrome supplied)

supplied with Integrated models
with badge only

6

4

PRODUCT DIMENSIONS

AHI

J

K

Side

Plan

G

F

B

CD

E

Product dimensions (mm)

STANDARD HEIGHT MODELS TALL HEIGHT MODELS

Classic

Designer

Integrated

Remote

control

Integrated

Badge

control

Classic

Designer

Integrated

Remote

control

456 mm cavity

Integrated

Badge

control

456 mm cavity

Integrated

Remote

control

480 mm cavity

Integrated

Badge

control

480 mm cavity

A

overall height1 of product (incl. front panel height) 410 410 410 410 454 478

2

454 454 478

2

478

2

B

overall width of product 599 599 599 599 599 599 599 599 599 599

C

overall depth of product (excl. handle) 582 571 571

3

571

3

582 571 571

3

571

3

571

3

571

3

D

depth of chassis (to back of front panel) 553 553 553 553 553 553 553 553 553 553

E

maximum extension of drawer (excl. handle) 556 545 545

3

545

3

556 545 545

3

545

3

545

3

545

3

F

depth of front panel (excl. handle) 29 18 16-20 16-20 29 18 16-20 16-20 16-20 16-20

G

height1 of chassis 410 410 410 410 454 454 454 454 454 454

H

depth of handle n/a 41 n/a n/a n/a 41 n/a n/a n/a n/a

I

height of front panel 394 398 4084min. 398 438 470 4525min. 442 4765min. 470

J

height of ventilation gap below front panel 7 8 min. 2 min. 8 7 8 min. 2 min. 8 min. 2 min. 8

K

height from top of handle to top of front panel n/a 64 n/a n/a n/a 64 n/a n/a n/a n/a

1

includes 2mm high bracket slots 2Includes cavity bracket 3Assuming front panel thickness of 18 mm

4

Recommended for a 2 mm ventilation gap below panel, if cavity height is 412 mm 5Recommended for a 2 mm ventilation gap below panel

7

5

CABINETRY DIMENSIONS

min.

412mm

456mm 480mm

LL L

dishwasher dishwasher dishwasher

Standard height models

Tall height Classic models

Tall height Integrated models

Compact

Oven

Single
Oven

Tall height Designer models

Plan

Side

L

N

M

Cavity height options allow you to match dishwasher with your cabinetry or companion products

Minimum clearances from adjacent cabinetry

You may choose to install Tall height Integrated
models into either a 456 mm or a 480 mm high cavity.
Note: the minimum height of the custom drawer front

panel will also be different for these two options.

Cabinetry dimensions (mm)

STANDARD HEIGHT MODELS TALL HEIGHT MODELS

Classic

Designer

Integrated

Remote

control

Integrated

Badge

control

Classic

Designer

Integrated

Remote

control

456 mm cavity

Integrated

Badge

control

456 mm cavity

Integrated

Remote

control

480 mm cavity

Integrated

Badge

control

480 mm cavity

L

inside height of cavity min. 412 min. 412 min. 412 min. 412 456 480 456 456 480 480

M

inside width of cavity 600 600 600 600 600 600 600 600 600 600

N

inside depth of cavity min. 560 min. 560 min. 560 min. 560 min. 560 min. 560 min. 560 min. 560 min. 560 min. 560

min. 13 mm
clearance
from a corner

min. 2 mm
clearance
to adjacent
cupboard door

8

The following calculations assume the top of the panel is aligned
with the top of the adjacent cabinetry:

WIDTH OF THE PANEL

Measure

A (

the width between adjacent door/drawer fronts)

and write it in the  rst box below, then complete the equation.

HEIGHT OF THE PANEL

Measure B and write it in the  rst box below, then complete
the equation.

min. 2 mm

min. 2 mm

min. 2 mm ventilation gap
with external venting kit
installed

min. 2 mm ventilation gap with

external venting kit installed

min. 2 mmmin. 2 mm

WIDTH OF PANEL

HEIGHT
OF PANEL

A

B

A

B

clearance to
adjacent cabinet
front (min. 2 mm)

ventilation gap

(min. 2 mm)

WIDTH OF PANEL

(min. 596 mm)

HEIGHT OF PANEL

- 2x

-

=

=

FRONT PANEL SPECIFICATIONS

16 -20 mm panel thickness
Maximum weight of panel: 9 kg
Adequately sealed to withstand moisture (50

O

C @ 80% RH).
Because of it being a hot and wet environment generally, the
back and sides of the panel should be completely sealed with a
waterproof vapour barrier (ie polyurethane) to prevent damage
to the panel.
The back of the panel (including any integrated handle) should
be completely flush so that the seal between the panel and the
rubber trim is maintained.

6a

Note: when the top of the dishwasher has to be lower than the adjacent cabinetry,
the panel can be increased in height.

INTEGRATED MODELS WITH REMOTE ONLY - CUSTOM FRONT PANEL CALCULATIONS

9

The following calculations assume the top of the panel is aligned
with the top of the adjacent cabinetry:

WIDTH OF THE PANEL

Measure

A (

the width between adjacent door/drawer fronts)

and write it in the  rst box below, then complete the equation.

HEIGHT OF THE PANEL

Measure B and write it in the  rst box below, then complete
the equation.

min. 2 mm

min. 2 mm

min. 8 mm ventilation gap

min. 8 mm ventilation gap

min. 2 mmmin. 2 mm

WIDTH OF PANEL

HEIGHT
OF PANEL

A

B

A

B

clearance to
adjacent cabinet
front (min. 2 mm)

ventilation gap

(min.8 mm)

WIDTH OF PANEL

(min. 596 mm)

HEIGHT OF PANEL

- 2x

-

=

=

FRONT PANEL SPECIFICATIONS

16 -20 mm panel thickness
Maximum weight of panel: 9 kg
Adequately sealed to withstand moisture (50

O

C @ 80% RH).
Because of it being a hot and wet environment generally, the
back and sides of the panel should be completely sealed with a
waterproof vapour barrier (ie polyurethane) to prevent damage
to the panel.
The back of the panel (including any integrated handle) should
be completely flush so that the seal between the panel and the
rubber trim is maintained.

6b

Note: when the top of the dishwasher has to be lower than the adjacent cabinetry,
the panel can be increased in height.

INTEGRATED MODELS WITH BADGE ONLY - CUSTOM FRONT PANEL CALCULATIONS

10

7a

CAVITY PREPARATION

Water Connection

Recommended COLD
(Maximum 60°C).

¾ “ BSP (GB20) to
suit flat washer.

Water Pressure

Water softener models

Max. 1 MPa (145 psi)
Min. 0.1 MPa (14.5 psi)

Models without water
softener

Max. 1 MPa (145 psi)
Min. 0.03 MPa (4.3 psi)

Important!

Adjacent cabinetry
must not extend
above cavity base

Important!

The power outlet must be
located in a cabinet adjacent
to the dishwasher cavity.

220-240 VAC min. 4.8 A

min.

ø

60 mm

min. 200 mm

Moisture

protection

tape must

be applied.

Services can be
located either side
of the dishwasher.

These marks indicate
formed bracket screw
locations, if securing
by drawer removal.

10 mm

BENCHTOP

11

7b

7c

ø

60 mm

ø

60 mm

max.

5 mm

max.

5 mm

220 mm

220 mm

100 mm

100 mm

ø

60mm

Services can be located
either side of dishwasher

VENT HOSE

VENT HOSE
& SERVICES

SERVICES

Services can be located
either side of dishwasher

Shelf cutouts

Shelf cutouts

The ø60 mm services hole should
be enlarged to accomodate the
extra venting hose by
cutting out some material from
the bottom corner.

External Venting kit (1)

External Venting kit (1)

INTEGRATED MODELS WITH REMOTE ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINET

INTEGRATED MODELS WITH REMOTE ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH ADJACENT CABINET

min. 100 mm

min.100 mm

Important!

To prevent pooling of condensation from the vent hose, a
toekick height of no less than 100 mm is required.

Important!

To prevent pooling of condensation from the vent hose, a
toekick height of no less than 100 mm is required.

12

8

MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE

Left hand side Right hand side

Drain hose - 2000 mm

Inlet hose - 1650 mm

Venting hose - 1525 mm

(Integrated wireless models only) (Integrated wireless models only)

Venting hose - 1925 mm

Power cord

(excl. plug)

- 1650 mm

Drain hose - 1800 mm

Inlet hose - 1250 mm

Power cord

(excl. plug)

- 1650 mm

Drain hose - 2000 mm

Drain hose - 1800 mm

Inlet hose - 1650 mm

Inlet hose - 1250 mm

Venting hose - 1525 mm

Venting hose - 1925 mm

(Integrated models with
remote (NZ AU) only)

(Integrated models with
remote (NZ AU) only)

Power cord (excl. plug) - 1650 mm

Power cord (excl. plug) - 1650 mm

13

TALL HEIGHT DESIGNER & INTEGRATED MODELS FOR 480 mm CAVITY ONLY - ATTACH CAVITY BRACKET

9

The enclosed cavity bracket is  tted before installation in order to conceal the gap at the top of the cavity left after installation.

2

1

Ensure the cavity panel
bracket is positioned so
that the “F” arrow is
pointing towards the front
of the chassis.

Firmly push the bracket so that
the prongs engage with the top
tabs and it clicks into place.

Ensure the top trim seal
is facing forward after
attaching the bracket.

Important!

Ensure the prongs have not been
driven down into the chassis as
this will damage the lid below.

12

14

RECOMMENDED METHOD (a) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)

11a10a

ATTACH SIDE MOUNTING BRACKETS

Fitted Elbow

Clip all four side mounting
brackets into their slots
using a flat-bladed
screwdriver. Ensure they’re
securely fitted before
sliding product into cavity.

The mounting slots are in pairs,
one on each side diagonally
across the product. A bracket
must match A slot and B
bracket must match B slot.

Check that the fitted elbow is rotated
left or right (depending on the direction
of the routing), then ensure the venting
hose is securely attached to it.

NOW CHOOSE WHICH INSTALLATION METHOD (a) or (b)

IS MORE SUITABLE FOR YOUR CABINETRY...

B

B

B

A

A

A

A

B

INTEGRATED MODELS WITH REMOTE ONLY ­ATTACH VENTING HOSE

15

12a 13a

PULL THROUGH HOSES & MOVE INTO THE CAVITY SECURE THE DRAWER

As you push product in, pull through hoses and
cord, ensuring they don’t get kinked or twisted.

Important!

If product cannot be pushed in far enough, pull
out again and rearrange hoses and cord. Do not
use excessive force, as doing so may squash the
hoses and lead to incorrect operation.

vent either
through
same cabinet
or adjacent
cabinet as per
step 7b or 7c



1

32

Open the

drawer halfway.

Using a flat-bladed

screwdriver, prise

the grey

rubber plug out

of the trim moulding.

Replace the grey
rubber plug back into
the trim moulding
and ensure the trim
seal is facing forward.

Repeat for all
four brackets.

Using a small Philips

screwdriver,

screw through the trim

moulding, securing the

side mounting bracket

to the cabinetry.

Do not damage the

rubber trimseal.

14a

2

1

After routing the vent hose
through and out the hole
cutout, attach and secure the
vent by tightening the four
screws provided.

Airflow

Vent Hose
(Integrated models
with remote (NZAU)
only)

INTEGRATED MODELS WITH REMOTE ONLY - SECURE THE EXTERNAL VENT

16

11b10b

PULL THROUGH HOSES & MOVE INTO THE CAVITY

Fitted Elbow

Check that the fitted elbow is
rotated left or right (depending
on the direction of the routing),
then ensure the venting hose is
securely attached to it.

vent either
through
same cabinet
or adjacent
cabinet as per
step 7b or 7c

ALTERNATIVE METHOD (b) - SECURE BY DRAWER REMOVAL

INTEGRATED MODELS WITH REMOTE ONLY ­ATTACH VENTING HOSE

As you push product in, pull through hoses and
cord, ensuring they don’t get kinked or twisted.

Important!

If product cannot be pushed in far enough, pull
out again and rearrange hoses and cord. Do not
use excessive force, as doing so may squash the
hoses and lead to incorrect operation.

Vent Hose
(Integrated models
with remote (NZAU)
only)

17

12b 13b

14b 15b

REMOVE THE DRAWER SECURE THE DRAWER TO THE CABINETRY

REFIT THE DRAWER ONTO THE RUNNERS

2

1

4

5

3

Before refitting the drawer,
ensure the hoses are not
twisted and the latches at
the rear of each drawer
runner are facing forward.

Ensure the release tabs on
both sides are reset fully.

Ensure the drawer
is now rotated
clockwise back.

2

100 mm

1

3

4

5

100 mm

To prevent kinked hoses, we recommend
rotating the drawer anti-clockwise and
resting it on its side after removal.

Press the release tabs
in on either side and
push back to release
drawer from runners

Push drawer runners back in.

Product may
move. Mark
chassis position
on cavity

1

2

The product has three
pairs of fixing points:

Ensure the sound insulation is
repositioned correctly.

a pair of fixing
holes either side on
the bottom
(use 38 mm fixing
screws & washers)

two pairs of formed
brackets on either
side of the chassis
(use 16 mm screws)

2

1

After routing the vent hose
through and out the hole
cutout, attach and secure the
vent by tightening the four
screws provided.

Airflow

Pull forward the release tabs
on both sides 100

mm

INTEGRATED MODELS WITH REMOTE ONLY ­SECURE THE EXTERNAL VENT

18

1

2

16 mm x6

2

2

1

Important!

Ensure the rubber seal
between the drawer
and panel is kept in
place.

REMOVE BRACKET FROM PRODUCT

ATTACH PANEL TO PRODUCT

ATTACH PANEL TO PANEL BRACKET

There must be at least

3 screws used each side

When refitting the
door pins,
ensure they are
orientated as shown.

Align bottom of panel

with bottom of bracket

16a

18a

17a

19a

INTEGRATED MODELS WITH REMOTE ONLY - INSTALLING THE FRONT PANEL

1

1

2

3

Electrical Shock Hazard

Before continuing, ensure that the product is
disconnected from the power supply.

Failure to follow this warning may result in
electrical shock, injury or re.

WARNING!

EARTH THE PANEL

WARNING!

WARNING!

To earth the panel bracket, connect the earth
wire from the product to one of the tabs.
Any custom metal component (e.g. handle)
that extends past the rubber seal must be
earthed too.

Failure to follow these warnings may result
in electrical shock, injury or  re.

Electrical Shock Hazard

Repeat for the other drawer

19

ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS

With the front panel fitted, insert an appropriately
sized Philips screwdriver into the hole above the
door pin and rotate the panel up or down to align
the gaps in your cabinetry.

Repeat on the other side if necessary.

The panel has a maximum travel of 2 mm up or
down.

Important!

Ensure that you maintain a minimum of 2 mm ventilation
gap below the panel.

+ or - 2 mm

20a

INTEGRATED MODELS WITH REMOTE ONLY - INSTALLING THE FRONT PANEL

20

1

2

16 mm x6

DETERMINE BADGE CUTOUT LOCATION

ROUTE BADGE WIRING THROUGH PANEL ATTACH PANEL TO PANEL BRACKET

REMOVE BRACKET & DISCONNECT BADGE

16b

18b 19b

17b

There must be at least

3 screws used each side

Align bottom of panel

with bottom of bracket

228.5 mm

228.5 mm

127 mm

255 mm

30 mm

25 mm

1

3

4

1

2

1

2

Badge zone

INTEGRATED MODELS WITH BADGE ONLY - INSTALLING THE FRONT PANEL & BADGE CONTROLS

Electrical Shock Hazard

Before continuing, ensure that the product is
disconnected from the power supply.

Failure to follow this warning may result in
electrical shock, injury or re.

WARNING!

21

2

2

1

ATTACH PANEL TO PRODUCT

ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS

20b

22b

21b

With the front panel fitted, insert an appropriately
sized Philips screwdriver into the hole above the
door pin and rotate the panel up or down to align
the gaps in your cabinetry.

Repeat on the other side if necessary.

The panel has a maximum travel of 2 mm up or
down.

Important!

Ensure that you maintain a minimum of 8 mm ventilation
gap below the panel.

+ or - 2 mm

Important!

Ensure the rubber seal
between the drawer
and panels is kept in
place.

When refitting the
door pins, ensure
they are
orientated as shown.

Push the panel in
then up to locate.

INTEGRATED MODELS WITH BADGE ONLY - INSTALLING THE FRONT PANEL & BADGE CONTROLS

REATTACH BADGE & EARTH THE PANEL

1

2

WARNING!

Electrical Shock Hazard

Connect the integrated badge
earth wire to one of the two tabs
provided on the panel bracket.

To earth the panel bracket,
connect the earth wire from the
product to the other tab.
Any custom metal component
(e.g. handle) that extends past the
rubber seal must be earthed too.

Failure to follow these warnings
may result in electrical shock,
injury or  re.

22

THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.

23

1

3

2

750-882.5 mm

1

2

38 mm

max.
120
mm

750-882.5 mm

**

3 4

5

If space is limited
for fixing, push
hose through drain
hose support
to required height

If space is limited
for fixing, push
hose through drain
hose support
to required height

Dishwasher using sink trap with drain hose joiner

750 - 882.5 mm

750 - 882.5 mm

min. R 200 mm

min. R 200 mm

Supplied drain hose joiner
19 mm waste tee

HIGHLOOP

min. 150 mm

Ensure drain hose is routed straight
to joiner. Remove excess drain hose
material if necessary.

Do not shorten the inlet hose.

Dishwasher and Standpipe Ø 38 mm

Ensure the
supplied
rubber
washer is
fitted inside
the coupling.

Tighten coupling with spanner.

180

o

No leaks!

CONNECT INLET HOSE TO COLD WATER PLUG PRODUCT IN

24 25

1 2

24 24see see

Important!

Do not connect the
drain hose to a waste
disposal unit, as this
type of connection may
lead to a blockage in
the drain hose.

23

27

26

FINAL CHECKLIST TROUBLESHOOTING

Check all parts are installed.
Ensure that all panels and parts thereof are secure and final electrical tests have

been conducted in accordance with local electrical regulations.

Ensure product is level, securely fastened to the cabinetry and opens and

closes freely. The drawer must be free to fully close with no resistance from the

cabinetry.

Ensure inlet hose to water supply has supplied rubber washer fitted, and that

it’s tightened a further half turn after seal contact.

Ensure any knockouts or plugs in drain connection have been drilled out and

drain connection has been made.

The drain hose joiner must not support the weight of excess hose material.

Keep drain hose as fully extended as possible to prevent sagging. Any excess

length of drain hose should be kept on the dishwasher side of the highloop.

If connecting the drain hose to the sink trap, ensure the Highloop is a minimum

150 mm higher than the drain hose joiner.

Ensure any packaging or tape securing the racks is removed from the drawer.

Turn on the power and water supplies, then open the drawer. You should hear a

beep and see a program indicator light up on the internal control panel.

Check the spray arm is in place and free to rotate.

Add three cups of water into the drawer. Press

on the internal control panel

until the indicator of the ‘Rinse’ program lights up. Close the drawer and press

to start the program.

After the Rinse program has finished, ensure the dishwasher has run and

drained correctly.

Check water supply and drainage connection for leakage.

Spray arm

Excessive water remaining above the filter plate, after the rinse cycle

Check for a kinked drain hose, blocked waste connection, highloop not
properly installed, drain hose not routed correctly or spray arm not in place.

No water supply (This is displayed as a ‘U1’ fault -- see section ‘If there is a
fault’ in the User guide for how to recognise this fault on models without a
display.)

Check water is connected and turned on.

The dishwasher is beeping continuously

There is a fault. See section ‘If there is a fault’ in the User guide for further

information and instructions.

No program indicator lights up when the drawer is opened

Ensure power is connected and is switched on. If it is and still no indicator
ligths up, see the ‘Preference options’ section of the ‘Quick start guide’. An
option called ‘Open drawer auto power-on’ may need to be turned on.

Water around water supply and drainage connections

Check connections, existing plumbing and hoses for leaks. Check rubber
washer and hose clamp are correctly fitted.

If product is tipping

Ensure the product is secured to the cabinetry.

If front panels are misaligned

Check and relevel product. Check the cabinetry is square. For Integrated
models, check and adjust front panel alignment if necessary.

Drawer doesn’t close properly

Ensure nothing is obstructing the drawer from closing properly eg sound
insulation, hoses or drawer latches.
If a problem occurs, consult the ‘Troubleshooting’ section of the User guide.
If after checking these points you still need assistance, please refer to the
Service & Warranty book for warranty details and your nearest Authorised
Service Centre, or contact us through our website, listed below.

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change
at any time. For current details about model and specification availability in your country, please
visit our website listed at the end of this document or contact your local Fisher & Paykel dealer.

www. sherpaykel.com