Fisher Paykel CPV2366LN, CPV2364GDLN, CPV2304LN Installation

PROFESSIONAL COOKTOP

CPV2 models

INSTALLATION GUIDE

US CA

591105B 01.18

48” models

2 MODEL IDENTIFICATION

CPV2-488

CPV2-486GD CPV2-486GL

36” models

CPV2-366 CPV2-364GD

30” models

CPV2-304

CPV2-485GD

Unpacking and handling

●

Inspect the product to verify that there is no shipping damage.
If any damage is detected, call the shipper and initiate a damage
claim. Fisher & Paykel is not responsible for shipping damage.

●

DO NOT discard any packing material (box, pallet, straps) until
the unit has been inspected.

●

Remove the outer carton and any packing material from the
shipping base.

●

The cooktop should be moved close to its final location.
Electric and gas connections should be made and the backguard
installed before the cooktop is placed in its final position.

4

B

E

A

F

I

H

G

A

C

D

J

KL

CPV2-486GD model shown
for illustration purposes only

Note: Gas inlet connection is located in the
rear left corner.

5 PRODUCT & CUTOUT DIMENSIONS – ALL MODELS

TOP

TOP

PRODUCT AND CUTOUT DIMENSIONS

A

Height below countertop to bottom of chassis / Height of cutout 8” (203) 8” (203) 8” (203)

B

Overall height of product (bottom of chassis to top of grates) 9 15/16’’ (253) 9 15/16’’ (253) 9 15/16’’ (253)

C

Overall width of cooktop 29 7/8’’ (759) 35 7/8’’ (911) 47 7/8’’ (1216)

D

Overall depth of cooktop 28 1/8’’ (714) 28 1/8’’ (714) 28 1/8’’ (714)

E

Height above countertop to top of grates 1 15/16’’ (50) 1 15/16’’ (50) 1 15/16’’ (50)

F

Height from countertop to chassis top surface 3/8” (10) 3/8” (10) 3/8” (10)

G

Height of chassis 8 3/8’’ (213) 8 3/8’’ (213) 8 3/8’’ (213)

H

Distance from left edge of chassis to center line of gas inlet 2 1/2’’ (63) 2 1/2’’ (63) 3’’ (77)

I

Distance from left edge of chassis to center line of power cord 10 5/8’’ (270) 10 5/8’’ (270) 10 5/8’’ (270)

J

Width of cutout min 30” (762) min 36” (915) min 48” (1219)

K

Depth of cutout for projecting control panel 24 3/16’’ (614) 24 3/16’’ (614) 24 3/16’’ (614)

L

Depth of cutout for flush control panel 26 5/8” (677) 26 5/8” (677) 26 5/8” (677)

6

FRONT

SIDE

30” MODELS 36” MODELS 48” MODELS

inches (mm) inches (mm) inches (mm)

7 COOKTOP INSTALLATION SCENARIOS AND USE OF BACKGUARDS

Important notes

●

There are three different backguards available for purchase:

●

Wall Mount Low Backguard

●

Wall Mount High Backguard with Low Shelf

●

Wall Mount High Backguard with High Shelf.

●

For installations against non-combustible* surfaces only, you may install the cooktop without a backguard or choose any of the three backguards.

●

For installations close to combustible surfaces (above the cooking surface), without a backguard, there must be a minimum 6” (152mm) clearance (see Scenario 2 or 7 opposite)

●

For installations immediately against combustible surfaces (above the cooking surface), you must purchase the Wall Mount High Backguard High Shelf (scenario 5 opposite).

●

The cooking surface must sit flush or above the adjacent countertop level.

* Non-combustible surfaces:
as defined in ‘National Fuel Gas Code’ (ANSI Z223.1, Current Edition). Clearances from non-combustible materials
are not part of the ANSI Z21.1 scope and are not certified by UL. Clearances of less than 6” (152mm) must be
approved by the local codes and/or by the local authority having jurisdiction.

BACKGUARD MODEL NUMBERS

COOKTOP

WALL
MOUNT LOW
BACKGUARD

WALL
MOUNT HIGH
BACKGUARD
LOW SHELF

WALL
MOUNT HIGH
BACKGUARD
HIGH SHELF

BACKGUARD
WIDTH

30” models BGCV2-1230 BGCV2-3030 BGCV2-3030H 29 7/8” (759mm)

36” models BGCV2-1236 BGCV2-3036 BGCV2-3036H 35 7/8” (911mm)

48” models BGCV2-1248 BGCV2-3048 BGCV2-3048H 47 7/8” (1216mm)

Note: Backguard Installation Instructions can also be downloaded from our website www.fisherpaykel.com

9